Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Computational optimization of the dual-mode dual-fuel concept through genetic algorithm at different engine loads

  • Xu, Guangfu
  • Jia, Ming
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • García Martínez, Antonio|||0000-0001-5783-4936
[EN] The diesel/gasoline dual-mode dual-fuel (DMDF) combustion concept was optimized in a compression-ignition engine by combining the computational fluid dynamics (CFD) simulations with the genetic algorithm. Seven operating parameters with remarkable influences on the engine performance were chosen as the variables to be optimized for simultaneously minimizing the fuel efficiency, nitrogen oxides (NOx), and soot emissions. Moreover, the potential of the further improvement of the DMDF combustion concept was discussed, and the rationality of this strategy was demonstrated. The results indicate that, at low load, simultaneous improvement of the fuel economy and emissions can be realized by strengthening the homogeneous combustion. At mid load, the fuel economy can be improved by reducing the heat transfer losses, while the NOx emissions are sacrificed to some extent. At high load, improved fuel economy can be realized by transferring a part of diffusion combustion to premixed reactivity-controlled compression ignition (RCCI) combustion. Concerning the operating parameters, lower intake temperature is beneficial to decrease the transfer losses, and the control of intake temperature is crucial for the stable operation of DMDF combustion under wide load conditions. Overall, gross indicated thermal efficiency above 45% is achieved, and the NOx and soot emission can be maintained under the Euro 6 standard for the test load range., This work was partially supported by the National Natural Science Foundation of China (Grant Nos. 51961135105 and 91641117) and China Postdoctoral Science Foundation (Grant No. 2019M661094). The experimental results used in this investigation were obtained in a project funded by VOLVO Group Trucks Technology. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

CFD Modeling of Reacting Diesel Sprays with Primary Reference Fuel

  • Zhou, Qiyan
  • Lucchini, Tommaso
  • D'Errico, Gianluca
  • Lu, Xingcai
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • García-Oliver, José M|||0000-0002-2676-9681
[EN] Computational fluid dynamics (CFD) modeling has many potentials for the design and calibration of modern and future engine concepts, including facilitating the exploration of operation conditions and casting light on the involved physical and chemical phenomena. As more attention is paid to the matching of different fuel types and combustion strategies, the use of detailed chemistry in characterizing auto-ignition, flame stabilization processes and the formation of pollutant emissions is becoming critical, yet computationally intensive. Therefore, there is much interest in using tabulated approaches to account for detailed chemistry with an affordable computational cost. In the present work, the tabulated flamelet progress variable approach (TFPV), based on flamelet assumptions, was investigated and validated by simulating constant-volume Diesel combustion with primary reference fuels - binary mixtures of n-heptane and iso-octane. Simulations were initially carried out to evaluate and compare the performance of two kinetic models in homogeneous reactors and laminar diffusion flames, followed by turbulent reacting spray simulations considering different fuels, ambient temperatures, and oxygen concentrations. The sensitivity study of the turbulent Schmidt number was then conducted, and results in terms of ignition delay and lift-off length were compared with experimental data to determine a more appropriate global constant. Finally, parametric variations of ambient temperature and oxygen concentration were performed for six fuel blends ranging from PRF0 (n-heptane) to PRF100 (iso-octane), confirming the validity of the TFPV model., Authors acknowledge the financial support from the China Scholarship Council (No. 201806230180) and Natural Science Foundation of China (No. 51961135105) for the first author's study in Politecnico di Milano, Italy
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Computational optimization of the piston bowl geometry for the different combustión regimes of the dual-mode dual-fuel (DMDF) concept through an improved genetic algorithm

  • Xu, Guangfu
  • Jia, Ming
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
[EN] Focusing on the dual-mode dual-fuel (DMDF) combustion concept, a combined optimization of the piston bowl geometry with the fuel injection strategy was conducted at various loads. An improved genetic algorithm was introduced in this study, which is superior in searching for the global optimal solutions. The optimal piston bowl shape coupled with the corresponding injection strategy was summarized at the various loads. The results show that the piston bowl geometry optimization can further improve the thermal efficiency with 1.4%, 4.4%, and 1.4% percentage points for the low, mid, and high loads, respectively. An indicated thermal efficiency up to 51.8% can be realized at mid load. Meanwhile, for all the optimal cases, NOx and soot emissions can meet the Euro VI limits. At low and mid loads, both the open and re-entrant type piston bowl can be equipped, while the high load only prefers the open type piston bowl for the DMDF mode. The re-entrant type or deep piston bowls are superior in organizing strong in-cylinder flow, which is beneficial for the fuel/air mixing. The open type or shallow piston bowls are helpful for reducing the heat transfer losses owing to the less heat transfer surface area. Furthermore, a correlation analysis was conducted to investigate the sensitivity of engine performance to the piston geometric parameters and injection parameters. It is concluded that the fuel injection event becomes more important for managing the engine performance as load increases. Among the injection parameters, the influence of the fuel injection timings and injection pressure on engine performance is more obvious. The piston geometric parameters play more significant roles in the heat transfer losses than the injection parameters for all loads. Among the geometric parameters, the most influential parameters are the width and open extent of the piston bowl. The heat transfer loss energy fraction can be well decreased with a wider and more open piston bowl., This work was partially supported by the National Natural Science Foundation of China (Grant Nos. 51961135105 and 91641117) and Postdoctoral Research Foundation of China (Grant Nos. 2019M661094 and 2020T130075). The experimental results used in this investigation were obtained in a project funded by VOLVO Group Trucks Technology. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Val`encia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

CFD analysis of combustion and emission characteristics of primary reference fuels: from transient Diesel spray to heavy-duty engine

  • Zhou, Qiyan
  • Lucchini, Tommaso
  • D'Errico, Gianluca
  • Lu, Xingcai
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • García-Oliver, José M|||0000-0002-2676-9681
[EN] The pre-blending of low- and high-reactivity fuels for a single direct injection system has been proven to be an effective way to control the reactivity of mixtures in compression ignition engines, having the potential to simultaneously reduce fuel consumption and pollutant emissions. However, there is not much knowledge about the complex physical-chemical phenomena in the turbulent sprays with fuels having widely different autoignition qualities, although this information is critical for the design and development of cleaner combustion systems based on this concept. For this reason, a computational analysis of ignition behavior, flame structure, and soot production for reacting sprays with five primary reference fuels (PRFs), from PRF0 (n-heptane) to PRF80 (20% n-heptane, 80% iso-octane) with 20% increment in iso-octane mass fraction, was first performed using the Tabulated Flamelet Progress Variable (TFPV) approach based on the tabulation of diffusion flamelets for different scalar dissipation rates. The temporal and spatial features of the flame structure and soot formation for different fuels were investigated with the so-called intensity-axial distance-time (IXT) plots. Then, ten PRFs, from RRF0 to PRF90 with 10% increment in iso-octane mass fraction, were investigated and compared in a heavy-duty Diesel engine operating at the conventional high-temperature, short-ignition delay (HTSID) condition. The injection timing was altered from -5 to -13 degrees ATDC to optimize the combustion phase and engine performance for different fuels. The results showed that PRF70 exhibited the best performance at the tested condition, which reduced the soot mass to 5% of the baseline value without sacrificing fuel efficiency., Authors acknowledge the financial support from the China Scholarship Council (No. 201806230180) and Natural Science Foundation of China (No. 51961135105) for the first author's study in Politecnico di Milano, Italy