Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of laser irradiation on failure mechanism of TiCp reinforcedtitanium composite coating produced by laser cladding

  • Candel Bou, Juan José
  • Jiménez, J.A.
  • Franconetti Rodríguez, Patricia
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Laser cladding is an effective technique to coat a metallic substrate with a layer of a different nature.It has been widely reported that the most important combined parameters controlling the quality ofthe coating are the specific energy (E) and the powder density ( ). In the present work, clad depositsof Ti6Al4V + 60 wt.% TiC were prepared on a Ti6Al4V substrate using an optimum combination of Ec= 24 J/mm2 and c= 3 mg/mm2. These experiments were performed using a laser power of 400 and600 W, in order to study the effect of laser power on the properties of the clad. The microstructure, phasecomposition and nanohardness of the coatings were investigated by optical microscopy, scanning elec-tron microscopy and X-ray diffraction. During laser processing, TiC can be partially converted to TiCX(X = 0.5) due mainly to the TiC dissolution into the laser-generated melting pool and subsequent precipi-tation during cooling. It was observed that the lower laser power limit reduces primary TiC dissolution butit also promotes secondary carbide alignment at the interface. On the other hand, the damage mechanisminduced by high laser power is dominated by primary TiC particle cracking by the high stress concentra-tion at the particle matrix interface followed by ductile failure of the matrix. It is also remarkable thatirradiance affects the TiC/TiCxratio despite Ecand care fixed and it determines hardness distributioninside the coating., Authors thank MINECO funding in special the Training of Research Staff programme with the help BES-2009-013589 and the support of the Comision Interministerial de Ciencia y Tecnologia (CICYT), Spain, under Grant MAT2012-39124. This work was developed at the Materials Technology Unit of the Polytechnic University of Valencia associated to CSIC through the National Centre for Metallurgical Research (CENIM). Finally, thank the EU for the funding received through the FEDER help in the project UPOV08-3E-005 for the purchase of equipment and the Generalitat Valenciana for the help ACOMP/2012/094.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Comportamiento frente a la oxidación de aleaciones de titanio alfa + beta

  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
  • Schalht, A.
  • Amigó Mata, Angèlica
[EN] Las aleaciones alfa+beta, presentan excelentes propiedades mecánicas y frente a la corrosión lo que las hace excelentes candidatas para su aplicación en la industria química y aeronáutica, pero es importante mejorar su comportamiento frente a elevadas temperaturas, sobre todo su oxidación a esas temperaturas. En el presente trabajo se estudia la obtención de aleaciones + del tipo Ti-3%at. X (Nb, Mo, Ta) por vía pulvimetalúrgica a partir de mezcla elemental de polvos y su caracterización microestructural, con análisis específico de su resistencia a la oxidación a elevadas temperaturas. La microestructura se caracteriza mediante microscopía óptica y electrónica. La resistencia mecánica de las aleaciones se obtiene mediante ensayos de flexión y análisis fractográfico. La resistencia frente a la oxidación se ha determinado mediante una termobalanza Q50 de TA Instruments a 900º durante 200 minutos. Los mecanismos de corrosión se han analizado a través de sus óxidos superficiales, caracterizados mediante microscopía electrónica de barrido (SEM) y microscopía de fuerza atómica (AFM). Todas las aleaciones investigadas presentan estructura + con densidades entre el 90 y 94%. Además, presentan elevada resistencia a flexión, alrededor de los 1750-1800 MPa de carga de rotura, y elevada dureza; con una resistencia a la oxidación sensiblemente mayor que la correspondiente al titanio puro comercial. La difracción de rayos-X (XRD) y espectroscopia Raman confirman la formación de óxidos de titanio como fase principal. En conclusión la adición de los elementos de aleación aumenta en dos veces su resistencia frente a la oxidación a elevadas temperaturas., Los autores agradecen al MINECO la financiación del proyecto de investigación bilateral con Brasil PIB2010BZ-00448, a la UE por la financiación FEDER UPOV08-3E-005 para la compra de equipamiento y a la Generalitat Valenciana por la ayuda ACOMP/2013/094.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Efecto de las variables de proceso sobre el comportamiento a flexión de aleaciones Ti - 3% at. X (X = Nb, Ta) obtenidas por pulvimetalurgia, Effect of process variables on the flexural behavior of alloys Ti - 3% at. X (X = Nb, Ta) obtained by powder metallurgy

  • Franconetti Rodríguez, Patricia
  • Candel Bou, Juan José
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[ES] El niobio y el tantalio se añaden al titanio para formar nuevas aleaciones beta con mayor biocompatibilidad para aplicaciones biomédicas. Ambos elementos tienen un elevado punto de fusión, por lo que su difusión en estado sólido es limitada. En este trabajo se han fabricado por pulvimetalurgia muestras de titanio con 3% atómico de niobio o tantalio. Se estudia el efecto de la presión de compactación, la temperatura y el tiempo de sinterizado sobre la resistencia, la elasticidad y la ductilidad a flexión. Los resultados muestran que ambos elementos se comportan de manera semejante: aumenta la resistencia entre 20-25%, la elasticidad entre 0-10% y la ductilidad en más de un 150%. Por tanto, la adición de estos elementos es beneficiosa para las propiedades mecánicas. El análisis estadístico muestra que el efecto de la temperatura y presión son importantes mientras que el efecto del tiempo es poco significativo e incluso perjudicial en estas aleaciones., [EN] Niobium and tantalum are added to titanium alloys to form new beta alloys with higher biocompatibility for biomedical applications. Both elements have a high melting point, that is the reason for their limited solid state diffusion. In this work samples of titanium with 3% at. niobium and tantalum have been manufactured by powder metallurgy. The effect of the compacting pressure, temperature and the sintering time on the strength, elasticity and ductility in bending has been studied. The results show that both elements behave similarly: flexural strength increases between 20-25%, elasticity between 0-10% and ductility over 150%. Therefore, the addition of these elements is beneficial to mechanical properties. Statistical analysis shows that the effect of temperature and pressure are important, while the effect of time is insignificant and even harmful in these alloys., Los autores agradecen al MINECO la financiación a través del programa de Formación de Personal Investigador con la ayuda BES-2009-013589 así como a través del proyecto de investigación bilateral con Brasil PIB2010BZ-00448. Este trabajo se ha desarrollado en la Unidad de Tecnología de Materiales de la Universidad Politécnica de Valencia asociada al CSIC a través del Centro Nacional de Investigaciones Metalúrgicas (CENIM). Por último, agradecer a la UE por la financiación recibida a través del FEDER en el proyecto UPOV08-3E-005 para la compra de equipamiento y a la Generalitat Valenciana por la ayuda ACOMP/2012/094.