Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Combustion Modeling Approach for the Optimization of a Temperature Controlled Reactivity Compression Ignition Engine Fueled with Iso-Octane

  • Pelosin, Mattia
  • Spohr-Fernandes, Cássio
  • Lucchini, Tommaso
  • Marmorini, Luca
  • Zhou, Qiyan
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
[EN] In this study, an innovative Low Temperature Combustion (LTC) system named Temperature Controlled Reactivity Compression Ignition (TCRCI) is presented, and a numerical optimization of the hardware and the operating parameters is proposed. The studied combustion system aims to reduce the complexity of the Reaction Controlled Compression Ignition engine (RCCI), replacing the direct injection of high reactivity fuel with a heated injection of low reactivity fuel. The combustion system at the actual state of development is presented, and its characteristics are discussed. Hence, it is clear that the performances are highly limited by the actual diesel-derived hardware, and a dedicated model must be designed to progress in the development of this technology. A Computational Fluid Dynamics (CFD) model suitable for the simulation of this type of combustion is proposed, and it is validated with the available experimental operating conditions. The Particle Swarm Optimization (PSO) algorithm was integrated with the Computational Fluid Dynamic (CFD) software to optimize the engine combustion system by means of computational simulation. The operating condition considered has a relatively high load with a fixed fuel mass and compression ratio. The parameters to optimize are the piston bowl geometry, injection parameters and the boosting pressure. The achieved system configuration is characterized by a wider piston bowl and injection angle, and it is able to increase the net efficiency of 3% and to significantly reduce CO emissions from 0.407 to 0.136 mg., This research has been supported by Grant UPV-SOLGEN-79674 funded by Universitat Politecnica de Valencia. This research has been supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana. The author C. S. Fernandes thanks the Universitat Politècnica de València for his predoctoral contract (FPI-2019-S2-20-555), which is included within the framework of Programa de Apoyo para la Investigación y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Thermo-economic analysis of an oxygen production plant powered by an innovative energy recovery system

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Gutierrez, Fabio Alberto
[EN] Oxy-fuel combustion is considered an attractive alternative to reduce pollutant emissions, which uses high-purity oxygen mixed instead of air for combustion processes. However, purchasing large amounts of high-purity oxygen may be unprofitable for certain industrial sectors, discouraging its implementation. Considering this, the potential of an oxygen production cycle for factories using oxy-fuel combustion is studied by performing a thermo-economic analysis where high-purity oxygen, electricity, and natural gas prices are considered. Oxygen is produced by membrane means, where mixed ionic-electronic conducting membranes are used, which require high temperatures and pressure gradients to work properly. A set of turbochargers is implemented, chosen by scaling an off-the-shelf model, what introduces an innovative way of waste energy recovering for improving the performance of the cycle. The whole cycle is powered by waste heat from high temperature flue gases, and it is sized for a ceramic manufacturing factory. In this work, two cases are analysed, differentiated by considering additional heating and the vacuum generation method in the oxygen line. The first case exhibits smaller production levels, although better profitability (31¿€t¿1), whereas the second case displays higher production levels and production costs (33¿€t¿1). Both cases are competitive concerning the average price of high-purity oxygen, supposing an average of 50¿€t¿1 in wholesale markets, proving the potential of the proposed alternative for oxygen production., This research work has been supported by Grant PDC2021120821-I00 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR. This work has also been supported by Grant UPV-SOLGEN-79674 funded by the Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia (PAID-11-21). The authors want to acknowledge the institution "Conselleria d'Educacio, Investigaci o, Cultura i Esport de la Generalitat Valenciana" and its grant program "Subvenciones para la contratacion de personal investigador de caracter predoctoral" for doctoral studies (ACIF/2020/246) funded by The European Union. Also, this work is part of grant number INNVA1/2021/38 funded by "Agencia Valenciana de la Innovacion (AVI)" and by "ERDF A way of making Europe".