Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Monitoring and decontamination technologies for removing waterborne micro- and nanoplastic contaminants

  • Amonte, Cecilia
  • Gracia-Vallés, Nicolás
  • Mitchell, Scott G.
  • Gurauskis, Jonas
Micro- and nanoplastics (MNPs) are accumulating worldwide, posing a threat to ecosystems and biodiversity due to the ongoing global demand. In the literature there is a wide variety of procedures for sampling and characterizing MNPs in water samples, highlighting a lack of standardized methods, particularly plastics in the nanometric range (<0.1 μm), which require the removal of larger particles (>1.0 μm) followed by a concentration step to reach the quantification limits of analytical techniques. Proper sampling is essential for collecting representative samples, followed by a pre-treatment to remove suspended particles, which may interfere in the subsequent analysis. Consequently, specific techniques are employed to isolate the MNPs from the matrix samples and proceed to visual and chemical characterization. This review compiles key data on MNP characterization and advocates for a “best practices” toolbox to overcome current challenges, proposing a conceptual framework for developing efficient MNP characterization and supporting potential decontamination technologies., This project has received funding from Pathfinder Open 2022, a European Innovation Council (EIC) work program that is part of Horizon Europe (grant agreement no. 101099528) and UK Innovation Funding Agency (UKRI) (reference no. 10062709). This work was also supported through CEX2023-001286-S funded by MCIN/AEI/10.13039/501100011033 (Ministerio de Ciencia e Innovación/Agencia Estatal de Investigación, Spain). This study was supported by MCIN with funding from the European Union NextGenerationEU, With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preparation and characterization of different immobilized and chemically modified preparations of lipase B from Candida antarctica: is it the activation energy a good indicator of the biocatalyst expressed activity?

  • Hackenhaar, Camila R.
  • Abellanas-Perez, Pedro
  • Carballares, Diego
  • Bolivar, Juan M
  • Rodrigues, Rafael C
  • Fernandez-Lafuente, Roberto
Lipase B from Candida antarctica immobilized on octyl (via interfacial activation) and octyl-vinyl sulfone (covalently attached) agarose beads via different immobilization protocols was submitted to amination and/or glutaraldehyde modifications. The catalytic performance of the resulting biocatalysts significantly varied across different substrates: using octyl-CALB with the double modification, activity increased 3.5 fold versus triacetin and decreased by 5 % using R-methyl mandelate, while using the covalent biocatalyst, activity increase by 2.2 or 20 %, respectively. Similarly, the stability of the biocatalysts -both in absolute and relative terms- was strongly influenced by the inactivation pH and the substrate used for residual activity determination. Under the tested conditions, activity versus substrate concentration followed first-order kinetics up to the substrate solubility limit, preventing the determination of kinetic parameters such as Kcat or Km. Activation energy (Eₐ) for triacetin hydrolysis was also measured for each biocatalyst under different inactivation states. Interestingly, no consistent correlation was found between Eₐ and enzyme activity. Generally, partial inactivation of the biocatalysts increased Eₐ, although some exceptions were observed. These findings suggest that Eₐ alone does not directly correlate with enzymatic activity, highlighting the complex interplay between structural enzyme modifications, substrate used to determine the enzyme activity, and the enzyme catalytic behavior., JMB acknowledges funding from project CNS2022-135541 financed by MICIU/AEI /10.13039/501100011033 and by European Union NextGeneration EU/PRTR. DCN and JMB acknowledges funding from Pathfinder Open 2022, a European Innovation Council (EIC) work program that is part of Horizon Europe (grant agreement no. 101099528) and UK Innovation Funding Agency (UKRI) (reference no. 10062709). RFL acknowledges the support from MINECO and AEI via project PID2022-136535OB-I00. RCR acknowledges the support from CNPq (Process: 403151/2023-6) and FAPERGS (Process: 22/2551-0000397-4). CRH acknowledges the support by the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior – Brazil (CAPES) – Finance Code 001., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sol–gel-free electrospinning of α-Al2O3 suspensions: A systematic study on processing commercial powders into ceramic fibers

  • Fuentes-García, J. A.
  • Gurauskis, Jonas
This study optimizes the fabrication of electrospun α-Al2O3 ceramic fibers from commercial powders, focusing on the synergy between solid loading (α-Al2O3 solid oxide), solvent systems (water/alcohol), and surfactant (PVP) molecular weight (K15 and K30) for suspension elaboration. Rheological characterization identified a highly suitable processing window with consistency indices (K) of 3.85–4.85 Pa·s and pseudoplastic flow (n) ranging from 0.927–0.972 for the elaborated suspensions. The dominant viscoelastic liquid character (G’> G”), high electrical conductivity (up to 1825 μS/cm), and reduced surface tension (58–64 mN/m) facilitated stable Taylor cone formation and enhanced jet thinning. A breakthrough was achieved by increasing solid loading and transitioning to high-molecular-weight PVP K-30. This strategy, coupled with isopropanol-based solvents, provided steric stabilization and structural recovery necessary to maintain single-fiber integrity during both spinning and sintering at 1500 °C. The resulting fibers exhibited high micrometric uniformity and morphological retention despite the formation of intermediate aluminum oxycarbides. This research demonstrates a robust, cost-effective, and scalable route for designing advanced ceramic scaffolds directly from industrial precursors., This work has received funding from the European Union’s Horizon Europe Climate, Energy and Mobility (CL5) Project 101236115-C2FUe-LS, EIC Pathfinder Open program under Grant Agreement No.101099528 (BMRex). This work wasalso supported by the UK Research and Innovation (UKRI) agency under Grant Agreement No. 10062709. This research was further supported by the European Union−Next Generation EU and the Ministerio de Ciencia e Innovación (Spain) via the coordinated action “GreenLiFTech” in the framework of the subproject N-GasCat (TED2021−130621B−C41)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Reseña (Review)

Monitoring and decontamination technologies for removing waterborne micro- and nanoplastic contaminants

  • Amonte, Cecilia
  • Gracia-Vallés, Nicolás
  • Mitchell, Scott G.
  • Gurauskis, Jonas
Micro- and nanoplastics (MNPs) are accumulating worldwide, posing a threat to ecosystems and biodiversity due to the ongoing global demand. In the literature there is a wide variety of procedures for sampling and characterizing MNPs in water samples, highlighting a lack of standardized methods, particularly plastics in the nanometric range (<0.1 μm), which require the removal of larger particles (>1.0 μm) followed by a concentration step to reach the quantification limits of analytical techniques. Proper sampling is essential for collecting representative samples, followed by a pre-treatment to remove suspended particles, which may interfere in the subsequent analysis. Consequently, specific techniques are employed to isolate the MNPs from the matrix samples and proceed to visual and chemical characterization. This review compiles key data on MNP characterization and advocates for a “best practices” toolbox to overcome current challenges, proposing a conceptual framework for developing efficient MNP characterization and supporting potential decontamination technologies.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Sol–Gel-Free Electrospinning of α-Al <sub>2</sub> O <sub>3</sub> Suspensions: A Systematic Study on Processing Commercial Powders into Ceramic Fibers

  • Fuentes-García, Jesús Antonio
  • Gurauskis, Jonas
This study optimizes the fabrication of electrospun α-Al2O3 ceramic fibers from commercial powders, focusing on the synergy between solid loading (α-Al2O3 solid oxide), solvent systems (water/alcohol), and surfactant (PVP) molecular weight (K15 and K30) for suspension elaboration. Rheological characterization identified a highly suitable processing window with consistency indices (K) of 3.85–4.85 Pa·s and pseudoplastic flow (n) ranging from 0.927–0.972 for the elaborated suspensions. The dominant viscoelastic liquid character (G’> G”), high electrical conductivity (up to 1825 μS/cm), and reduced surface tension (58–64 mN/m) facilitated stable Taylor cone formation and enhanced jet thinning. A breakthrough was achieved by increasing solid loading and transitioning to high-molecular-weight PVP K-30. This strategy, coupled with isopropanol-based solvents, provided steric stabilization and structural recovery necessary to maintain single-fiber integrity during both spinning and sintering at 1500 °C. The resulting fibers exhibited high micrometric uniformity and morphological retention despite the formation of intermediate aluminum oxycarbides. This research demonstrates a robust, cost-effective, and scalable route for designing advanced ceramic scaffolds directly from industrial precursors.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Rheological design and characterization of Al2O3-based pastes for the direct ink writing of CFD-optimized woodpile scaffolds

  • Amonte Lopez, Cecilia
  • Fuentes-García, Jesús Antonio
  • Quindimil, Adrián
  • Gurauskis, Jonas
This study presents a strategy for the design and fabrication framework of Direct Ink Writing (DIW) manufactured Al2O3-based scaffolds, integrating computational fluid dynamics (CFD) and experimental rheological optimization. First, CFD simulations were performed under gas flow conditions to evaluate the impact of internal geometry on the permeability, pressure drop, unit mass flow and outward mass flow rate, comparing Woodpile (WP) architectures with 90° and 45° strut orientations. The WP90 configuration promotes high mass flow, evidenced by a lower pressure drop. While the WP45 configuration created a more intricate fluid pathway, maximizing gas-scaffold interactions at the cost of higher flow resistance. Once the 3D structure was studied, the rheological behaviour of the multicomponent paste comprising PVP, hydroxypropyl cellulose, Darvan, and graphite for DIW was experimentally optimized to achieve the high-viscosity and shear-thinning properties required for the WP structures printability. The effects of solid loading (44-48 vol% vs. 57-61 vol%) and particle morphology in aqueous Al2O3-YSZ and Al2O3-Sepiolite pastes were investigated. Crucially, the study elucidates a system-dependent interaction mechanism where the graphite pore former acts as a reinforcing agent in granular Al2O3-YSZ pastes but functions as a lubricant in fibrous Al2O3-Sepiolite networks. This sequential approach ensures that the scaffold's performance is optimized at the design stage while maintaining high structural fidelity during the extrusion process.