Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A DC-DC Converter Based On Modified Flyback Converter Topology

  • Pesce, C.
  • Riedemann, J.
  • Andrade, I.
  • Peña, R.
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] This paper proposes a DC-DC power converter topology based on a modified Flyback Converter (FC). The aim of the proposed topology is to increase the voltage gain by connecting the inputs of N isolated FCs in parallel and the N secondary inductances in series. This scheme reduces the current in each switch then reducing the associated losses. A single diode and an output capacitance complete the power converter circuit. A Proportional+Integral (PI) controller is used to control the output voltage with the converter operating in discontinuous current mode. The proposed converter can handle more power than the standard FC with a low number of active power devices. The system is modeled using PSIM platform and experimental results are presented considering a 1kW prototype., Este trabajo fue financiado por Universidad de La Frontera, Temuco, Chile, bajo el proyecto DIUFRO17-0044. También se agradece el aporte financiero entregado por Fondecyt Chile bajo el contrato 1151325 y CONICYT/FONDAP/15110019 y al Ministerio de Economía Español por el contrato DPI2014- 53245-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Vector control of an open-ended winding induction machine based on a two-output indirect matrix converter

  • Riedemann, Javier
  • Clare, Jon
  • Wheeler, Pat
  • Cardenas, Roberto
  • Peña, Ruben
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] The open-ended winding induction machine fed from a standard two-level Voltage Source Inverter (VSI) arrangement is an attractive solution for AC drives. An alternative power converter approach is to use an Indirect Matrix Converter (IMC) consisting of a matrix converter AC-DC input stage and two VSI output stages. This latter topology provides fully bidirectional power flow operation and requires only a small input filter. In this paper, a vector control strategy for an open-ended winding cage induction machine fed by a two-output IMC is presented. The modulation scheme for the input power converter stage aims to modify the virtual DC link voltage depending on the load voltage requirement. Additionally, the modulation strategy for the dual-inverter output aims to eliminate the zero sequence voltage applied to the load. A vector control scheme is used and the full system is modelled using a PSIM and MATLAB/Simulink platform. Experimental results from a 7.5 kW prototype are presented, demonstrating the feasibility of the topology and control strategy., This work was supported by The Chilean Research Fondecyt [grant number 1151325]; CONICYT/FONDAP/15110019.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Open-End Winding Induction Machine Fed by a Dual-Output Indirect Matrix Converter

  • Riedemann, Javier
  • Clare, J.C.
  • Wheeler, P.W.
  • Rivera, Marco
  • Peña, Rubén
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] Open-ended winding induction machines fed from standard two-level voltage source inverters (VSIs) provide an attractive arrangement for ac drives. An alternative approach is to use a dual-output indirect matrix converter (IMC). It is well known that the IMC provides fully bidirectional power flow operation, with small input size filter requirements. While a standard IMC consists of an ac dc matrix converter (MC) input stage followed by a single VSI output stage, it is possible to replicate the VSI to produce multiple outputs. In this paper, an open-end winding induction machine fed by an IMC with two output stages is presented. The IMC modulation strategy aims to reduce the common-mode voltage (CMV), while compensating any zero-sequence voltage fed to the machine. The system is modeled using a PSIM and MATLAB/Simulink platform. Experimental results demonstrating the viability of the method are presented using a 7.5-kW prototype., This work was supported in part by the Fondecyt/1151325, in part by the CONICYT/FONDAP/15110019, and in part by The Newton Picarte Project EPSRC: EP/N004043/1: New Configurations of Power Converters for Grid Interconnection Systems/CONICYT DPI20140007.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A multilevel modular DC DC converter topology

  • Vidal, R.
  • Soto, D.
  • Andrade, I.
  • Riedemann, J.
  • Pesce, C.
  • Belenguer, E.
  • Pena, R.
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] A multilevel modular DC DC power conversion topology based on cascaded H-Bridge converters in a double II configuration is presented. The topology is intended to interconnect large power DC networks. A two level control hierarchy is used to regulate the DC voltage of each H-bridge module. At the top level, DC and circulating AC currents are used to control the total energy converter in all branches (both parallels and series) of each II arrange. At bottom level, the voltage balance of a converter branch, which comprises N H-bridge modules, is carried out by balancing (N-1) capacitor voltage deviations, with respect to the average capacitor voltage. The entire topology and control strategies are simulated in a PSIM environment. Simulation results with three H-bridge converters per branch are shown and preliminary experimental results with a low power prototype are also included., This work was supported by Fondecyt grant 1151325, CONICYT/FONDAP/15110019, The Spanish Ministry of Economy and EU FEDER funds under grant DPI2014-53245-R, The University of Magallanes grant PR-FI-02IE14/15, Universitat Jaume I grant P1.1B2013-51, the Newton Picarte Project EPSRC:EP/N004043/1 and CONICYT DPI20140007.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Model aggregation of large wind farms for dynamic studies

  • Martínez-Turégano, Jaime|||0000-0002-3483-8253
  • Añó Villalba, Salvador Conrado|||0000-0002-8435-5225
  • Bernal-Perez, Soledad|||0000-0002-5431-9792
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
  • Chaqués-Herráiz, G.
[EN] A large number of nodes is required for the detailed simulation of large off-shore wind farms. Therefore, the corresponding electromagnetic transient simulations require large simulation times. This paper compares a detailed model of an off-shore wind farm with three clusters of 50 wind turbines each one (i.e. a total of 150 wind turbines), with a simplified model consisting of three aggregated wind farms. The paper includes the aggregation criteria so equal power flows and voltages are obtained at the wind farms points of common coupling. The control is carried out using a centralized PI controller to control total active power, and a distributed droop control for active and reactive power control of each wind turbine. The proposed aggregation method leads to significant savings on computational times, with the aggregated models being more than three hundred and fifty times faster than the detailed ones. The results have been validated by means of detailed PSCAD/EMTDC simulations.v, The authors would like to thank the support of the Spanish Ministry of Economy and EU FEDER funds under grant DPI2014-53245-R. The support of CONICYT/FONDAP/15110019 and Fondecyt 1151325 is also kindly acknowledged. This project has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No. 691714.