Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of sintering additives on defect chemistry and hydration of BaZr0.4Ce0.4(Y,Yb)0.2O3-δ proton conducting electrolytes

  • Dayaghi, Amir Masoud
  • Polfus, Jonathan M.
  • Strandbakke, Ragnar
  • Pokle, Anuj
  • Vollestad, Einar
  • Haugsrud, Reidar
  • Norby, Truls
  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] The effects of NiO, ZnO, and CuO sintering additives (0.5, 1.0, or 2.0 wt%) on the sintering behaviour, effective acceptor concentration, and hydration thermodynamics are examined for BaZr0.4Ce0.4Y0.1Yb0.1O3_delta and BaZr0.4Ce0.4Y0.2O3_delta proton conducting electrolytes. Thermogravimetry of hydration shows that the sintering additives - except for 0.5 wt% CuO - lead to a decrease in the effective acceptor concentration, and the decrease per mole sintering additive is the largest for NiO. The absence of typical secondary phases such as BaY2NiO5 and the homogeneous distribution of Ni determined from elemental mapping imply that sintering additives dissolve into the perovskite lattice. Exsolution of metallic Ni and Cu upon reduction leads to a substantial recovery of the effective acceptor concentration. Subsequent oxidation is accompanied by a repeated decrease in the effective acceptor concentration as the sintering additives appear to re-dissolve. Defect chemical reactions are proposed to explain the observed results and these are supported by energetics from first principles calculations. Overall, NiO has the highest positive impact on densification and grain growth, and a relatively small amount of 0.5 wt% NiO or CuO is preferable to optimise both sintering and hydration., This study has received European Union's Horizon 2020-Societal Challenges Research and Innovation funding under grant agreement No 838077 (eCOCO2 project). The Research Council of Norway is acknowledged for computational resources provided through the Uninett Sigma2 project nn4604k and for support to the Norwegian Center for Transmission Electron Microscopy (NORTEM) national infrastructure project 197405.r Center for Transmission Electron Microscopy (NORTEM) national infrastructure project 197405.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluating oxide nanoparticle exsolution on A-site deficient PrBaCo 2 O 6-o electrodes

  • Carrillo-Del Teso, Alfonso Juan
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • López-García, Andrés
  • Fabuel Robledo, Maria
  • Delgado-Galicia, Blanca|||0009-0004-4655-5789
  • Isabelle Rodriguez|||0000-0001-5479-2494
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Solis, Cecilia
  • Haas, Sylvio
  • Vøllestad, Einar
  • Wachowski, Sebastian
  • Strandbakke, Ragnar
  • Norby, Truls
[EN] Nanoparticle exsolution is a powerful technique for functionalizing redox oxides in energy applications, particularly at high temperatures. It shows promise for solid oxide fuel cells and electrolyzers. However, exsolution of other chemistries like metal oxides is not well studied, and the mechanism is poorly understood. This work explores oxide exsolution in PrBa1¿xCo2O6¿¿ (x = 0, 0.05, 0.1, 0.15) double perovskites, practiced electrodes in proton ceramic fuel cells and electrolyzers. Oxide exsolution in PrBa1¿xCo2O6¿¿ aimed at boosting the electrocatalytic activity and was evaluated by varying intrinsic materials-related properties, viz. A-site deficiency and external parameters (temperature, under fixed time, and pO2 = 10¿5 atm conditions). The materials were analyzed with conventional characterization tools and synchrotron-based small-angle x-ray scattering. Unlike metal-nanoparticle exsolution, increasing the A-site deficiency did not enhance the extent of oxide-nanoparticle exsolution, whereas larger nanoparticles were obtained by increasing the exsolution temperature. Combined Raman spectroscopy and electron microscopy analysis revealed that BaCoO3, Co3O4, and amorphous BaCO3 nanoparticles were formed on the surface of the double perovskites after the reductive treatments. The present results demonstrate the complexity of oxide-nanoparticle exsolution in comparison with metal-nanoparticle exsolution. Further materials screening and mechanistic studies are needed to enhance our understanding of this method for functionalizing proton ceramic electrochemical cells (PCEC) electrodes., We acknowledge the Spanish Government through the M-ERA.NET Joint Call 2018 'FunKeyCat' (PCI2019-103742, RYC2021-033889-I), the Research Council of Norway (Grant No. 299736), and the National Science Centre Poland, which has received funding from the European Union's Horizon 2020 research and innovation program under Grant Agreement No. 685451. We thank the support of the Electronic Microscopy Service of the Universitat Politecnica de Valencia and the Norwegian Center for Transmission Electron Microscopy (NORTEM) (No. 197405/F50). The authors acknowledge DESY (Hamburg, Germany), a member of the Helmholtz Association HGF, for providing experimental facilities. SAXS-WAXS measurements were carried out at PETRA III (beamtime allocated for proposals I-20210219 and I-20210223), and the authors would like to thank Andre Conceicao for assistance in using the SAXSMAT beamline P62.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the cation distribution in acceptor doped Ba(Zr,Ce)O3-(Zr,Ce)O2 co-ionic composite electrolytes

  • Dayaghi, Amir Masoud
  • Jiang, Bo
  • Almeida Carvalho, Patricia
  • Haugsrud, Reidar
  • Norby, Truls
  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Composite co-ionic ceramic electrolytes that combine proton and oxide ion conductors hold potential for co-electrolysis of CO2 and H2O for syngas production due to flexible control of the transport numbers of the two charge carriers. Contrary to purely oxide ion co-electrolysis, co-ionic co-electrolysis embodies the supply of CO2 and H2O separately to the negative and positive electrodes, respectively. This study focuses on the development of a chemically stable co-ionic composite electrolyte of an acceptor-doped Ba(Zr,Ce)O3 proton conducting perovskite phase and an acceptor-doped (Ce,Zr)O2 oxide ion conducting fluorite phase, annealed at temperatures between 800 and 1600 degrees C. Comprehensive evaluations of the composites' microstructure, hydration, and conductivity were performed, revealing that annealing temperature and cation selection significantly impact the properties and performance of co-ionic electrolytes. Higher annealing temperatures drive cation redistribution, with the perovskite phase becoming zirconium-rich at its B-site and depleted in acceptor dopants, resulting in diminished hydration and protonic conductivity. Herein, we show that composites pairing cerium-rich fluorite phases (e.g., Ce0.8Gd0.2O1.9, CGO20, or Ce0.8Y0.2O1.9, CYO20) display markedly improved performance. The BaCe0.8Y0.2O2.9 (BCY20)-CYO20 system (1 : 1 weight ratio) achieved the highest conductivity (sigma = 0.01 Scm-1 at 650 degrees C in wet Ar), establishing itself as a promising candidate for co-ionic electrolyte applications in solid oxide electrochemical cells., This project has received European Union's Horizon 2020 research and innovation funding under grant agreement No. 838077. The Research Council of Norway is acknowledged for support to the Norwegian Center for Transmission Electron Microscopy (NORTEM) national infrastructure project 197405. The authors acknowledge the ESRF for provision of synchrotron radiation facilities under proposal number A31-1-270 and we would like to thank Wouter van Beek and Kenneth Marshall for assistance and support in using beamline BM31 (SNBL). The authors also thank Daniel Irving at the I15-1 beamline at the Diamond Light Source, UK, for synchrotron X-ray measurements.