Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tailoring oxide nanoparticle exsolution in La0.5Ba0.5-yCo1-xFexO3-[delta]

  • Balcerzak, Daria
  • Norby, Truls
  • Strandbakke, Ragnar
  • Gazda, Maria
  • Wachowski, Sebastian L.
  • López-García, Andrés
  • Carrillo-Del Teso, Alfonso Juan
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] We show that oxide nanoparticles (NPs) exsolve on La0.5Ba0.5-yCo1-xFexO3-¿ (x = 0-1, y = 0 or 0.01) in oxidizing conditions. The phenomenon occurs only in Co-containing materials and depends on pO2 and pH2O pressures. Under dry conditions, the smallest NPs average about 30 nm, with 200-300 NPs/mu m2 at pO2= 5 x 10-5 atm. For pO2= 1 atm, NP size increases to 100-200 nm, and population drops to a few to about 20 NPs/mu m2 depending on A-site nonstoichiometry and x. In humid conditions, the smallest NPs around 50 nm, with a peak of 100 NPs/mu m2 exsolve for pO2= 1. Transmission electron microscopy shows that exsolved NPs in La0.5Ba0.5-yCoO3-¿ are Ba-Orich. We propose defect chemistry models, indicating that exsolution is driven by oxidation reactions forming A-site vacancies, increasing exsolved material with higher pO2. We suggest that adsorbed water under humid conditions blocks nucleation sites, altering observed trends., Project FunKeyCat is supported by the National Science Centre, Poland, The Research Council of Norway (FunKeyCat 299736) , and the Spanish Government (PCI2019-103742, RYC2021-033889-I) under the M-ERA.NET 2, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement no 685451. We thank the support of the Electronic Microscopy Service of the Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Physicochemical properties of La0.5Ba0.5Co1-xFexO3-o (0 &lt, = x &lt, = 1) as positrode for proton ceramic electrochemical cells

  • Wachowski, Sebastian L.
  • Szpunar, Iga
  • Pospiech, Joanna
  • Balcerzak, Daria
  • Mielewczyk-Gryn, Aleksandra
  • Nadolska, Malgorzata
  • Vollestad, Einar
  • Gazda, Maria
  • Strandbakke, Ragnar
  • Norby, Truls
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] We report on essential properties of materials in the series La0.5Ba0.5Co1-xFexO3-delta as positrodes for proton ceramic electrochemical cells (PCECs). The unit cell and thermochemical expansion coefficient (TCEC) of these cubic perovskites decrease with iron content x, the TCEC of La0.5Ba0.5FeO3-delta going as low as 1110(-6) 1/K. The materials behave as LaMO3 perovskites with small band gaps and Ba acting as acceptors compensated by electron holes and oxygen vacancies. The electrical properties are dominated by p-type conduction with high large polaron mobilities for the Co-rich compositions at low temperatures, shifting towards small polaron mobilities with increasing Fe content. X-ray absorption spectroscopy (XAS) shows that Co is in a high spin state and takes on the main part of the cation oxidation state changes, and that hole states are in orbitals overlapping with the O 2p states, confirming the large polaronic behaviour, while holes on Fe are more localised at the cation. Hydration is more pronounced in inert atmospheres, as hydration of oxygen vacancies is easier than hydrogenation and increases with Fe content, in line with the commonly accepted finding that delocalization of holes disfavours protonation. Fe-rich compositions benefit from lower TCEC and higher hydration and hence expected proton permeability, at the cost of lower electronic conductivity. The surfaces are hydrophobic irrespective of Fe content, suggesting weak chemisorption of the underlaying water layer, possibly giving relatively many available surface sites for oxygen adsorption, but limited surface proton conductance - both of importance to positrodes for operando PCECs., This work is financed by The Research Council of Norway (Grant no 299736 "FunKeyCat") through the M-ERA.NET Joint Call 2018, and through project FunKey Cat supported by the National Science Centre, Poland under the M-ERA.NET 2, which has received funding from the European Union's Horizon 2020 research and innovation program under Grant agreement No 685451. Also M-ERA.NET in Spain and Spanish Ministry of Science and Innovation through the PCIN-2017-125, PIE 20238AT016, and RYC2021-033889-I funding is kindly acknowledged. We acknowledge the Solaris National Radiation Centre Poland for access to the XAS/PEEM beamline (proposal ID 191011) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluating oxide nanoparticle exsolution on A-site deficient PrBaCo 2 O 6-o electrodes

  • Carrillo-Del Teso, Alfonso Juan
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • López-García, Andrés
  • Fabuel Robledo, Maria
  • Delgado-Galicia, Blanca|||0009-0004-4655-5789
  • Isabelle Rodriguez|||0000-0001-5479-2494
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Solis, Cecilia
  • Haas, Sylvio
  • Vøllestad, Einar
  • Wachowski, Sebastian
  • Strandbakke, Ragnar
  • Norby, Truls
[EN] Nanoparticle exsolution is a powerful technique for functionalizing redox oxides in energy applications, particularly at high temperatures. It shows promise for solid oxide fuel cells and electrolyzers. However, exsolution of other chemistries like metal oxides is not well studied, and the mechanism is poorly understood. This work explores oxide exsolution in PrBa1¿xCo2O6¿¿ (x = 0, 0.05, 0.1, 0.15) double perovskites, practiced electrodes in proton ceramic fuel cells and electrolyzers. Oxide exsolution in PrBa1¿xCo2O6¿¿ aimed at boosting the electrocatalytic activity and was evaluated by varying intrinsic materials-related properties, viz. A-site deficiency and external parameters (temperature, under fixed time, and pO2 = 10¿5 atm conditions). The materials were analyzed with conventional characterization tools and synchrotron-based small-angle x-ray scattering. Unlike metal-nanoparticle exsolution, increasing the A-site deficiency did not enhance the extent of oxide-nanoparticle exsolution, whereas larger nanoparticles were obtained by increasing the exsolution temperature. Combined Raman spectroscopy and electron microscopy analysis revealed that BaCoO3, Co3O4, and amorphous BaCO3 nanoparticles were formed on the surface of the double perovskites after the reductive treatments. The present results demonstrate the complexity of oxide-nanoparticle exsolution in comparison with metal-nanoparticle exsolution. Further materials screening and mechanistic studies are needed to enhance our understanding of this method for functionalizing proton ceramic electrochemical cells (PCEC) electrodes., We acknowledge the Spanish Government through the M-ERA.NET Joint Call 2018 'FunKeyCat' (PCI2019-103742, RYC2021-033889-I), the Research Council of Norway (Grant No. 299736), and the National Science Centre Poland, which has received funding from the European Union's Horizon 2020 research and innovation program under Grant Agreement No. 685451. We thank the support of the Electronic Microscopy Service of the Universitat Politecnica de Valencia and the Norwegian Center for Transmission Electron Microscopy (NORTEM) (No. 197405/F50). The authors acknowledge DESY (Hamburg, Germany), a member of the Helmholtz Association HGF, for providing experimental facilities. SAXS-WAXS measurements were carried out at PETRA III (beamtime allocated for proposals I-20210219 and I-20210223), and the authors would like to thank Andre Conceicao for assistance in using the SAXSMAT beamline P62.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Additive manufacturing of Proton-Conducting Ceramics by robocasting with integrated laser postprocessing

  • Pospiech, Joanna
  • Nadolska, Malgorzata
  • Cieslik, Mateusz
  • Sobczyk, Tomasz
  • Chmielewski, Marek
  • Mielewczyk-Gryn, Aleksandra
  • Strandbakke, Ragnar
  • Wachowski, Sebastian Lech
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] A hybrid system combining robocasting and NIR laser postprocessing has been designed to fabricate layers of mixed proton-electron conducting Ba0.5La0.5Co1-xFexO3-delta ceramic. The proposed manufacturing technique allows for the control of the geometry and microstructure and shortens the fabrication time to a range of a few minutes. Using 5 W laser power and a scanning speed of 500 mm<middle dot>s(-1), sintering of a round-shaped layer with an 8 mm radius was performed in less than 2 s. The single phase of the final product was confirmed by X-ray diffraction. Various ceramic-to-polymer weight ratios were tested, showing that various porosities of microstructures of similar to 30 - 35 % and similar to 19 % can be obtained with 2:1 and 4:1 loading respectively., The project FunKeyCat is supported by the National Science Centre, Poland under the M-ERA.NET 2, which has received funding from the European Union's Horizon 2020 research and innovation program under Grant Agreement No 685451, from the Research Council of Norway (Grant n degrees 299736) , and the Spanish Government (M-ERA.NET PCI2019-103742) . The authors also express gratitude to Piotr Okoczuk, MSc Eng, for performing the confocal microscopy measurements and to Robert Tylingo, Ph.D., D.Sc. Eng., for conducting the viscosity measurements and for their contribution to this work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Governing principles of hydration of mixed proton conducting Co-based double perovskites

  • Strandbakke, Ragnar
  • Wachowski, Sebastian Lech
  • Vines, Lasse
  • Sky, Thomas Neset
  • Szpunar, Iga
  • Carvalho, Patricia A.
  • Mielewczyk-Gryn, Aleksandra
  • Sorby, Magnus H.
  • Gazda, Maria
  • Norby, Truls
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Proton ceramic electrochemical cells PCECs hold promise for efficient, sustainable production and use of hydrogen. The positive electrodes are mixed proton conducting perovskites that facilitate water splitting and oxygen reduction, but the factors that determine the protonation are poorly understood. Here, we establish the governing principles of protonation through a study of hydration of 45 double perovskites with the general formula A(I)A(II)Co(2)O(6_delta), having Ba or Ba+Sr on A(I) and a mix of rare earths (Y and lanthanides Ln = La, Pr, Nd, Sm, Gd, Dy, Tb, Lu) on A(II). We show how hydration is coupled to the A-site basicity and disorder as well as population of electron holes in the Co-O bond (Co oxidation state), promoted by a closed or semi-closed Ln 4 f shell, i.e., Ln = La, Gd, Lu., This work is financed by The Research Council of Norway (Grant nO 272797 "GoPHy MiCO" and nO 299736 "FunKeyCat") through the M-ERA.NET Joint Call 2016 and 2018 (R.S., M.H.S., T.N.). Project "FunKeyCat" is supported by the National Science Centre, Poland, under the M-ERA.NET 2, which has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement no 685451 (2016/22/Z/ST5/00691) (S.L.W., A.M.G., M.G.), and the Spanish Government through the National Research Agency AEI (grant PCIN-2017-125) (M.B., J.A.S.). This publication was partially developed under the provision of the Polish Ministry and Higher Education project "Support for research and development with the use of research infrastructure of the National Synchrotron Radiation Centre SOLARIS" under contract nr 1/SOL/2021/2 (S.L.W., A.M.G., M.G.). We acknowledge the SOLARIS Centre for access to the Beamline PIRX, where the measurements were performed. We thank Dr. Marcin Zaj & aogon;c for assistance (proposal nos. 191011 and 201036). We also thank Dr. Vegar & Oslash;ygarden for Rietveld refinements of NPD data.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Simultaneous local heating/thermometry based on plasmonic magnetochromic nanoheaters

  • Li, Zhi
  • López-Ortega, Alberto
  • Aranda-Ramos, Antonio
  • Tajada Herráiz, José Luis
  • Sort, Jordi
  • Nogués, Carme
  • Vavassori, Paolo
  • Nogués, Josep
  • Sepúlveda, Borja
A crucial challenge in nanotherapies is achieving accurate and real‐time control of the therapeutic action, which is particularly relevant in local thermal therapies to minimize healthy tissue damage and necrotic cell deaths. Here, a nanoheater/thermometry concept is presented based on magnetoplasmonic (Co/Au or Fe/Au) nanodomes that merge exceptionally efficient plasmonic heating and simultaneous highly sensitive detection of the temperature variations. The temperature detection is based on precise optical monitoring of the magnetic‐induced rotation of the nanodomes in solution. It is shown that the phase lag between the optical signal and the driving magnetic field can be used to detect viscosity variations around the nanodomes with unprecedented accuracy (detection limit 0.0016 mPa s, i.e., 60‐fold smaller than state‐of‐the‐art plasmonic nanorheometers). This feature is exploited to monitor the viscosity reduction induced by optical heating in real‐time, even in highly inhomogeneous cell dispersions. The magnetochromic nanoheater/thermometers show higher optical stability, much higher heating efficiency and similar temperature detection limits (0.05 °C) compared to state‐of‐the art luminescent nanothermometers. The technological interest is also boosted by the simpler and lower cost temperature detection system, and the cost effectiveness and scalability of the nanofabrication process, thereby highlighting the biomedical potential of this nanotechnology., This work was supported by the Spanish Ministry of Economy, Industry and Competitivenes (MINECO) projects MAT2013‐48628‐R, MAT2016‐77391‐R, and PCIN‐2016‐093 (H2020 M‐ERA.NET). Z.L. acknowledges the Chinese Scholarship Council (CSC) Program (201506950059) for financial support. The 2017‐SGR‐292 project of the Generalitat de Catalunya is acknowledged. The ICN2 was funded by the Centres de Recerca de Catalunya (CERCA) programme/Generalitat de Catalunya. The ICN2 was supported by the Severo Ochoa programme (MINECO, No. SEV‐2013‐0295). A.L.‐O. and P.V. acknowledge funding from the Basque Government (No. PI2015_1_19), MINECO and the European Regional Development Fund (FEDER) (No. FIS2015 64519 R). A.L.‐O. acknowledges the support from Juan de la Cierva grant. This work was also supported by MINECO under the Maria de Maeztu Units of Excellence (MDM‐2016‐0618). J.S. acknowledges the financial support by the European Research Council (SPIN‐PORICS 2014‐Consolidator Grant, Agreement No. 648454)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Oxide nanoparticle exsolution in Lu-doped (Ba,La)CoO3

  • Balcerzak, Daria
  • Szpunar, I.
  • Strandbakke, Ragnar
  • Saeed, Sarmad W.
  • Bazioti, Calliope
  • Mielewczyk-Gryn, Aleksandra
  • Winiarz, P.
  • Carrillo, Alfonso J.
  • Balaguer, María
  • Serra Alfaro, José Manuel
  • Gazda, M.
  • Wachowski, S.
This study investigated Lu doping of BaLaCoO and its influence on the exsolution of oxide nanoparticles (NPs). As a result of Lu doping, we observed the phase segregation into the main BaLaCoLuO (BLCO-Lu) phase and the secondary BaLaCoLuO (BCO-Lu) phase. We noticed the exsolution of BCO-Lu nanoparticles on the main BLCO-Lu phase. Moreover, the BLCO-Lu phase exsolved in the form of nanoparticles on the adjacent BCO-Lu grains. That shows that the phases are covered with mutually exsolved oxide NPs. In addition, trace amounts of the BaLuCoO phase are detected. We noticed that the exsolved oxides even in the as-prepared sample were fine (average size of 18 nm), and well distributed with a dense population of NPs above 280 per 1 μm. Furthermore, we showed that the size and shape of the exsolved oxide NPs can be controlled by varying the annealing temperature. For example, at 800 °C the exsolved oxides segregate and form two different shapes; spherical and cuboidal, with an average size of 31 nm and NP population of about 23 NPs per μm. Meanwhile, with lowering the temperature to 400 °C the oxides form only spherical and quite evenly distributed NPs with the occurrence of 137 NPs per 1 μm. The obtained results open the possibility of tailoring a novel, more catalytically active material for future applications in electrochemical devices., Project FunKeyCat is supported by the National Science Centre, Poland under the M-ERA.NET 2, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement no 685451. The Research Council of Norway is also acknowledged for support to the Norwegian Center for Transmission Electron Microscopy (NORTEM) (no. 197405/F50)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Additive manufacturing of Proton-Conducting Ceramics by robocasting with integrated laser postprocessing

  • Pospiech, Joanna
  • Nadolska, Malgorzata
  • Cieslik, Mateusz
  • Sobczyk, Tomasz
  • Chmielewski, Marek
  • Mielewczyk-Gryn, Aleksandra
  • Strandbakke, Ragnar
  • Serra Alfaro, José Manuel
  • Wachowski, Sebastian Lech
A hybrid system combining robocasting and NIR laser postprocessing has been designed to fabricate layers of mixed proton-electron conducting BaLaCoFeO ceramic. The proposed manufacturing technique allows for the control of the geometry and microstructure and shortens the fabrication time to a range of a few minutes. Using 5 W laser power and a scanning speed of 500 mm·s, sintering of a round-shaped layer with an 8 mm radius was performed in less than 2 s. The single phase of the final product was confirmed by X-ray diffraction. Various ceramic-to-polymer weight ratios were tested, showing that various porosities of microstructures of ∼30 - 35 % and ∼19 % can be obtained with 2:1 and 4:1 loading respectively., The project FunKeyCat is supported by the National Science Centre, Poland under the M-ERA.NET 2, which has received funding from the European Union's Horizon 2020 research and innovation program under Grant Agreement No 685451, from the Research Council of Norway (Grant n° 299736), and the Spanish Government (M-ERA.NET PCI2019-103742). The authors also express gratitude to Piotr Okoczuk, MSc Eng, for performing the confocal microscopy measurements and to Robert Tylingo, Ph.D., D.Sc. Eng., for conducting the viscosity measurements and for their contribution to this work.