Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of sintering additives on defect chemistry and hydration of BaZr0.4Ce0.4(Y,Yb)0.2O3-δ proton conducting electrolytes

  • Dayaghi, Amir Masoud
  • Polfus, Jonathan M.
  • Strandbakke, Ragnar
  • Pokle, Anuj
  • Vollestad, Einar
  • Haugsrud, Reidar
  • Norby, Truls
  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] The effects of NiO, ZnO, and CuO sintering additives (0.5, 1.0, or 2.0 wt%) on the sintering behaviour, effective acceptor concentration, and hydration thermodynamics are examined for BaZr0.4Ce0.4Y0.1Yb0.1O3_delta and BaZr0.4Ce0.4Y0.2O3_delta proton conducting electrolytes. Thermogravimetry of hydration shows that the sintering additives - except for 0.5 wt% CuO - lead to a decrease in the effective acceptor concentration, and the decrease per mole sintering additive is the largest for NiO. The absence of typical secondary phases such as BaY2NiO5 and the homogeneous distribution of Ni determined from elemental mapping imply that sintering additives dissolve into the perovskite lattice. Exsolution of metallic Ni and Cu upon reduction leads to a substantial recovery of the effective acceptor concentration. Subsequent oxidation is accompanied by a repeated decrease in the effective acceptor concentration as the sintering additives appear to re-dissolve. Defect chemical reactions are proposed to explain the observed results and these are supported by energetics from first principles calculations. Overall, NiO has the highest positive impact on densification and grain growth, and a relatively small amount of 0.5 wt% NiO or CuO is preferable to optimise both sintering and hydration., This study has received European Union's Horizon 2020-Societal Challenges Research and Innovation funding under grant agreement No 838077 (eCOCO2 project). The Research Council of Norway is acknowledged for computational resources provided through the Uninett Sigma2 project nn4604k and for support to the Norwegian Center for Transmission Electron Microscopy (NORTEM) national infrastructure project 197405.r Center for Transmission Electron Microscopy (NORTEM) national infrastructure project 197405.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Efficient CO2 and H2O Co-Electrolysis in a BaZr0.44Ce0.36Y0.2O3o-Based Proton Ceramic Electrochemical Reactor with BaGd0.8La0.2Co2O6-o Steam Electrodes

  • Barrio-Querol, Elena
  • Leonard, Kwati
  • Matsumoto, Hiroshige
  • Quina-García, Imanol
  • Fabuel Robledo, Maria
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
[EN] Despite the increasing use of electrification and efforts to decarbonize processes, hydrocarbons remain indispensable for heavy transport and chemistry sectors. Electrochemical devices powered by renewable energy offer a promising strategy to convert CO2 into sustainable molecules that can be used as fuels and chemical feedstocks. In this study, we investigate the electrochemical performance of BaGd0.8La0.2Co2O6-delta as a steam or oxygen electrode in a proton ceramic electrolysis cell. Two composite materials were evaluated as electrode candidates, consisting of BaGd0.8La0.2Co2O6-delta (BGLC) combined with either BaZr0.4Ce0.4Y0.1Yb0.1O3-delta (BZCYYb4411) or BaZr0.5Ce0.3Y0.2O3-delta (BZCY532). The electrodes were characterized using electrochemical impedance spectroscopy (EIS) on symmetrical cells under various oxidizing conditions and temperatures. Based on this analysis, the BGLC-BZCYYb4411 electrode was selected as the steam electrode in a full PCER configuration, composed of Ni-SrZr0.5Ce0.4Y0.1O2.95 (SZCY541) as the fuel/CO2 electrode and BaZr0.44Ce0.36Y0.2O3-delta as the electrolyte. The cell was evaluated for co-electrolysis of H2O and CO2. The results illustrate the potential of the BGLC-based electrodes and BZCY-based electrolytes for efficient CO2 upgrading and steam electrolysis in a single-step process., This study has received European Union Horizon 2020 Research and Innovation funding under Grant 838077 (Project eCOCO2). Financial support from the Spanish Government (Grant CEX2021-001230-S funded by MCIN/AEI/10.13039/501100011033, TED2021-132590B-C21, PRE2019-088857) and the Generalitat Valenciana (Grant CIACIF/2021/199) is also acknowledged. The authors acknowledge the support of the Servicio de Microscopia Electronica of the Universitat Politecnica de Valencia (UPV).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the cation distribution in acceptor doped Ba(Zr,Ce)O3-(Zr,Ce)O2 co-ionic composite electrolytes

  • Dayaghi, Amir Masoud
  • Jiang, Bo
  • Almeida Carvalho, Patricia
  • Haugsrud, Reidar
  • Norby, Truls
  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Composite co-ionic ceramic electrolytes that combine proton and oxide ion conductors hold potential for co-electrolysis of CO2 and H2O for syngas production due to flexible control of the transport numbers of the two charge carriers. Contrary to purely oxide ion co-electrolysis, co-ionic co-electrolysis embodies the supply of CO2 and H2O separately to the negative and positive electrodes, respectively. This study focuses on the development of a chemically stable co-ionic composite electrolyte of an acceptor-doped Ba(Zr,Ce)O3 proton conducting perovskite phase and an acceptor-doped (Ce,Zr)O2 oxide ion conducting fluorite phase, annealed at temperatures between 800 and 1600 degrees C. Comprehensive evaluations of the composites' microstructure, hydration, and conductivity were performed, revealing that annealing temperature and cation selection significantly impact the properties and performance of co-ionic electrolytes. Higher annealing temperatures drive cation redistribution, with the perovskite phase becoming zirconium-rich at its B-site and depleted in acceptor dopants, resulting in diminished hydration and protonic conductivity. Herein, we show that composites pairing cerium-rich fluorite phases (e.g., Ce0.8Gd0.2O1.9, CGO20, or Ce0.8Y0.2O1.9, CYO20) display markedly improved performance. The BaCe0.8Y0.2O2.9 (BCY20)-CYO20 system (1 : 1 weight ratio) achieved the highest conductivity (sigma = 0.01 Scm-1 at 650 degrees C in wet Ar), establishing itself as a promising candidate for co-ionic electrolyte applications in solid oxide electrochemical cells., This project has received European Union's Horizon 2020 research and innovation funding under grant agreement No. 838077. The Research Council of Norway is acknowledged for support to the Norwegian Center for Transmission Electron Microscopy (NORTEM) national infrastructure project 197405. The authors acknowledge the ESRF for provision of synchrotron radiation facilities under proposal number A31-1-270 and we would like to thank Wouter van Beek and Kenneth Marshall for assistance and support in using beamline BM31 (SNBL). The authors also thank Daniel Irving at the I15-1 beamline at the Diamond Light Source, UK, for synchrotron X-ray measurements.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Direct electrocatalytic CO2 reduction in a pressurized tubular protonic membrane reactor

  • Quina-García, Imanol
  • Almar-Liante, Laura|||0000-0001-5103-3812
  • MARTINEZ FELIU, AGUSTIN|||0000-0002-9974-1567
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Catalán-Martínez, David
  • Dayaghi, Amir Masoud
  • Norby, Truls
[EN] Power-to-methane technology enables storage of renewable elec-tricity in chemical energy, which can be transported and converted us-ing existing infrastructure. The moderate energy efficiency of this pro-cess is associated with high reactor exothermicity and complex thermal integration. Proton-ceramic electrochemical cells (PCECs) enable ther-mal combination of methanation and electrochemically driven H2 steps via endothermic reactions, boosting energy efficiency and heat man-agement. Here, we report single-step methane production from CO2 in a tubular PCEC at 450 degrees C and less than 30 bar. The H2 reactant is sup-plied by electrochemical pumping of protons from H2 in the external chamber. The electrochemical cell consists of an -25-mm-thick electro-lyte (BaZr0.8Ce0.1Y0.1O3-8) supported on a BaZr0.8Ce0.1Y0.1O3-8/Ni com-posite acting as a methanation catalyst. The reaction was studied as a function of total pressure, H2/CO2 ratio, and current density, reaching CH4 yields greater than 99% above 20 bar. High pressure and a CO2- rich atmosphere ameliorated the electrochemical behavior because of higher electrolyte hydration and boosted electrode kinetics., This study has received European Union Horizon 2020 Research and Innovation funding under grant agreement 838077 (eCOCO2 project) and financial support from the Spanish Government (PID2022-139663OB-I00, PRE2019-090959, and CEX2021-001230-S funded by MCIN/AEI/10.13039/501100011033) and MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and was carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transicion Energetica Sostenible+ (PTI-TRANSENER+). Support from Camilla Vigen (CoorsTek Membrane Sciences) with manufacture of tubular cells is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Direct hydrogenation of CO2 to aromatics via Fischer-Tropsch route over tandem K-Fe/Al2O3+H-ZSM-5 catalysts: Influence of zeolite properties

  • Murciano Martínez, Raúl
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • MARTINEZ FELIU, AGUSTIN|||0000-0002-9974-1567
[EN] Direct hydrogenation of CO2 to valuable aromatics using multifunctional catalysts is an attractive technology to produce low-carbon footprint chemicals. In this work, the relevant zeolite parameters driving the formation of total and BTEX aromatics from CO2 and H2 on tandem K-Fe/gamma-Al2O3+H-ZSM-5 catalysts following the FischerTropsch (FT)-mediated route were investigated. To this end, a set of H-ZSM-5 zeolites covering a wide range of physicochemical properties (density of Br phi nsted and Lewis acid sites, external acidity, crystallite size, and mesoporosity) was used, characterized by different techniques (ICP-OES, XRD, N2 physisorption, FTIR-pyridine, FTIR-2,6,-di-tert-butyl pyridine, XPS, 27Al MAS NMR, and electron microscopy), and evaluated in CO2 hydrogenation at 400 degrees C, 30 bar, H2/CO2 = 3.1, and GHSV of 4700 mL/(gFe-cat & sdot;h). At these conditions, high and stable CO2 conversions of 50 - 55% and low CO selectivity of ca. 10% were obtained for the Fe-based and tandem catalysts. The density and, to a certain extent, the strength of Br phi nsted acid sites were found the main parameters determining the selectivity of aromatics, reaching initial (TOS = 1.5 h) values of about 79% and 40% in liquid (C5+) and total hydrocarbons, respectively, for the catalyst based on the most acidic zeolite. Lewis acid sites associated to extraframework Al species (EFAL), by contrast, did not appear to play a relevant role in our conditions. Moreover, although a positive effect of the total amount and strength of Br phi nsted acid sites on the selectivity to the most valuable BTEX aromatics was inferred from our results, the external Br phi nsted acidity was the most influential factor in this case. Hence, a remarkable BTEX selectivity of 75% in aromatics was achieved for the zeolite previously submitted to a surface-passivation treatment by silylation., This work has received European Union's Horizon 2020 Research and Innovation funding under grant agreement No 838077 (eCOCO 2 project) . Funding by the Generalitat Valenciana through the Prometeo CIPROM/2022/10 project is also acknowledged. This study was supported by MICIN with funding from European NextGenerationEU (PRTR-C17. I1) within the Green Hydrogen and Energy Program-CSIC and CSIC Interdisciplinary Thematic Platform (PTI +) Transicion Energetica Sostenible + (PTI-TRANSENER +) . We are grateful to Dr. S. Escorihuela, Dr. M. Navarro, and Dr. J.A. Vidal-Moya for their assistance in part of the experimental work. The authors are also thankful to the Microscopy Service of the Universitat Polite cnica de Valencia (UPV) .
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Direct electrocatalytic CO2 reduction in a pressurized tubular protonic membrane reactor

  • Quina, Imanol
  • Almar, Laura
  • Catalán-Martínez, David
  • Dayaghi, Amir Masoud
  • Martínez, Agustín
  • Norby, Truls
  • Escolástico Rozalén, Sonia
  • Serra Alfaro, José Manuel
Power-to-methane technology enables storage of renewable electricity in chemical energy, which can be transported and converted using existing infrastructure. The moderate energy efficiency of this process is associated with high reactor exothermicity and complex thermal integration. Proton-ceramic electrochemical cells (PCECs) enable thermal combination of methanation and electrochemically driven H steps via endothermic reactions, boosting energy efficiency and heat management. Here, we report single-step methane production from CO in a tubular PCEC at 450°C and less than 30 bar. The H reactant is supplied by electrochemical pumping of protons from H in the external chamber. The electrochemical cell consists of an ∼25-μm-thick electrolyte (BaZrCeYO) supported on a BaZrCeYO/Ni composite acting as a methanation catalyst. The reaction was studied as a function of total pressure, H/CO ratio, and current density, reaching CH yields greater than 99% above 20 bar. High pressure and a CO-rich atmosphere ameliorated the electrochemical behavior because of higher electrolyte hydration and boosted electrode kinetics., This study has received European Union Horizon 2020 Research and Innovation funding under grant agreement 838077 (eCOCO2 project) and financial support from the Spanish Government (PID2022-139663OB-I00, PRE2019-090959, and CEX2021-001230-S funded by MCIN/AEI/10.13039/501100011033) and MCIN with funding from NextGenerationEU (PRTR-C17.I1) within the Planes Complementarios con CCAA (Area of Green Hydrogen and Energy) and was carried out in the CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). Support from Camilla Vigen (CoorsTek Membrane Sciences) with manufacture of tubular cells is gratefully acknowledged., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001230-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effects of sintering additives on defect chemistry and hydration of BaZr0.4Ce0.4(Y,Yb)0.2O3−δ proton conducting electrolytes

  • Dayaghi, Amir Masoud
  • Polfus, Jonathan M.
  • Strandbakke, Ragnar
  • Pokle, Anuj
  • Almar, Laura
  • Escolástico Rozalén, Sonia
  • Vøllestad, Einar
  • Serra Alfaro, José Manuel
  • Haugsrud, Reidar
  • Norby, Truls
The effects of NiO, ZnO, and CuO sintering additives (0.5, 1.0, or 2.0 wt%) on the sintering behaviour, effective acceptor concentration, and hydration thermodynamics are examined for BaZrCeYYbO and BaZrCeYO proton conducting electrolytes. Thermogravimetry of hydration shows that the sintering additives – except for 0.5 wt% CuO – lead to a decrease in the effective acceptor concentration, and the decrease per mole sintering additive is the largest for NiO. The absence of typical secondary phases such as BaYNiO and the homogeneous distribution of Ni determined from elemental mapping imply that sintering additives dissolve into the perovskite lattice. Exsolution of metallic Ni and Cu upon reduction leads to a substantial recovery of the effective acceptor concentration. Subsequent oxidation is accompanied by a repeated decrease in the effective acceptor concentration as the sintering additives appear to re-dissolve. Defect chemical reactions are proposed to explain the observed results and these are supported by energetics from first principles calculations. Overall, NiO has the highest positive impact on densification and grain growth, and a relatively small amount of 0.5 wt% NiO or CuO is preferable to optimise both sintering and hydration., This study has received European Union's Horizon 2020-Societal Challenges Research and Innovation funding under grant agreement No 838077 (eCOCO2 project). The Research Council of Norway is acknowledged for computational resources provided through the Uninett Sigma2 project nn4604k and for support to the Norwegian Center for Transmission Electron Microscopy (NORTEM) national infrastructure project 197405., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Direct hydrogenation of CO2 to aromatics via Fischer-Tropsch route over tandem K-Fe/Al2O3+H-ZSM-5 catalysts: Influence of zeolite properties

  • Murciano, Raúl
  • Serra Alfaro, José Manuel
  • Martínez, Agustín
Direct hydrogenation of CO to valuable aromatics using multifunctional catalysts is an attractive technology to produce low-carbon footprint chemicals. In this work, the relevant zeolite parameters driving the formation of total and BTEX aromatics from CO and H on tandem K-Fe/γ-AlO+H-ZSM-5 catalysts following the Fischer-Tropsch (FT)-mediated route were investigated. To this end, a set of H-ZSM-5 zeolites covering a wide range of physicochemical properties (density of Brønsted and Lewis acid sites, external acidity, crystallite size, and mesoporosity) was used, characterized by different techniques (ICP-OES, XRD, N physisorption, FTIR-pyridine, FTIR-2,6,-di-tert-butyl pyridine, XPS, Al MAS NMR, and electron microscopy), and evaluated in CO hydrogenation at 400 °C, 30 bar, H/CO = 3.1, and GHSV of 4700 mL/(g·h). At these conditions, high and stable CO conversions of 50 – 55% and low CO selectivity of ca. 10% were obtained for the Fe-based and tandem catalysts. The density and, to a certain extent, the strength of Brønsted acid sites were found the main parameters determining the selectivity of aromatics, reaching initial (TOS = 1.5 h) values of about 79% and 40% in liquid (C) and total hydrocarbons, respectively, for the catalyst based on the most acidic zeolite. Lewis acid sites associated to extraframework Al species (EFAL), by contrast, did not appear to play a relevant role in our conditions. Moreover, although a positive effect of the total amount and strength of Brønsted acid sites on the selectivity to the most valuable BTEX aromatics was inferred from our results, the external Brønsted acidity was the most influential factor in this case. Hence, a remarkable BTEX selectivity of 75% in aromatics was achieved for the zeolite previously submitted to a surface-passivation treatment by silylation., This work has received European Union’s Horizon 2020 Research and Innovation funding under grant agreement No 838077 (eCOCO2 project). Funding by the Generalitat Valenciana through the Prometeo CIPROM/2022/10 project is also acknowledged. This study was supported by MICIN with funding from European NextGenerationEU (PRTR-C17. I1) within the Green Hydrogen and Energy Program-CSIC and CSIC Interdisciplinary Thematic Platform (PTI+) Transición Energética Sostenible+ (PTI-TRANSENER+). We are grateful to Dr. S. Escorihuela, Dr. M. Navarro, and Dr. J.A. Vidal-Moya for their assistance in part of the experimental work. The authors are also thankful to the Microscopy Service of the Universitat Politècnica de València (UPV).