Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Compressive strength and microstructure of alkali-activated blast furnace slag/sewage sludge ash (GGBS/SSA) blends cured at room temperature

  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Reig, L.
  • Santini, M. A., Jr.
  • Moraes, J.C.B
  • Akasaki, J. L.
[EN] In the present work, ground granulated blast furnace slag (GGBS) and sewage sludge ash (SSA) blends were assessed for the production of alkali-activated pastes and mortars. Percentages of SSA to substitute GGBS ranged from 0 to 30 wt% and sodium concentrations of 6¿10 mol kg-1 were used for the activating solutions. Pastes and mortars were cured at 20 C for up to 90 days. Raw materials were characterised by granulometric analysis, XRF, XRD, FTIR and SEM techniques. The replacement percentage of GGBS by SSA and the sodium hydroxide concentration of the alkaline activator were optimised to produce mortar with compressive strengths close to 30 MPa after 28 curing days at room temperature. Best results were obtained in samples blended with 20 wt% SSA activated with 6 mol kg-1 NaOH solutions which, according to the XRD, FTIR and microscopic results,contained higher amounts of (N,C)¿A¿S¿H gel. The potential use of SSA for the development of alternative cementitious materials at room temperature has been demonstrated., The authors acknowledge FAPESP (processo 2013/25254-5), Santander Universidades (program: Becas Iberoame¿rica Jo¿venes Profesores Investigadores Espan a 2014 , Grant to Lucia Reig), CNPq (No 14/2013 processo 478057/2013-0) and the scanning electron microscopy services of FEIS/UNESP.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of the Pozzolanic Activity of Uncontrolled-Combusted Sewage Sludge Ash

  • Istuque, Danilo Bordan
  • Reig, Lucia
  • Pinheiro Melges, Jose Luiz
  • Akasaki, Jorge Luis
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
[EN] Waste management is a crucial issue facing modern society. The generation of sewage sludge is increasing annually due to the urbanization and improvement of sanitation systems of cities. The construction sector has emerged as a solution for the elimination of waste due to the enormous volume of materials that this sector can absorb. This paper evaluates the pozzolanic activity of sewage sludge ash (USSA) obtained following an uncontrolled-combustion process, a simple and economic procedure. Compressive strength of Portland cement/USSA mortars with 5%¿25% by weight USSA were evaluated. Calcium hydroxide/USSA and Portland cement/USSA pastes were chemically and physically characterized through thermogravimetric/differential-thermogravimetric (TG/DTG), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM) analyses. The increase in the replacement of Portland cement by USSA is associated with an increase in the compressive strength of mortars. These values for USSA containing mortars cured for 90 days were in the range of 49.6¿55.4 MPa, higher than the one reached by the reference mortar. According to the microstructural analysis, the increment on the compressive strength can be attributed to the formation of hydrated products (C¿S¿H, C¿A¿S¿H, and C¿A¿H) by the pozzolanic reaction of USSA., This research was financed in part by the Coordenacao de Aperfeicoamento de Pessoal de Nivel Superior-Brasil (Capes)Finance Code 001, and Conselho Nacional de Desenvolvimento Cientifico e Tecnologico (CNPq) (Processo Nos. 309015/2015-4 and 478057/2013-0). Thanks go to the Scanning Electron Microscopy Service of FEIS/UNESP, Servico Municipal Autonomo de Agua e Esgoto (SEMAE) from the Sao Jose do Rio Preto city (Sao Paulo, Brazil).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Flow shop scheduling with heterogeneous workers

  • Benavides, Alexander J.
  • Ritt, Marcus
  • Miralles Insa, Cristóbal Javier|||0000-0002-5269-9955
We propose an extension to the flow shop scheduling problem named Heterogeneous Flow Shop Scheduling Problem (Het-FSSP), where two simultaneous issues have to be resolved: finding the best worker assignment to the workstations, and solving the corresponding scheduling problem. This problem is motivated by Sheltered Work centers for Disabled, whose main objective is the labor integration of persons with disabilities, an important aim not only for these centers but for any company desiring to overcome the traditional standardized vision of the workforce. In such a scenario the goal is to maintain high productivity levels by minimizing the maximum completion time, while respecting the diverse capabilities and paces of the heterogeneous workers, which increases the complexity of finding an optimal schedule. We present a mathematical model that extends a flow shop model to admit a heterogeneous worker assignment, and propose a heuristic based on scatter search and path relinking to solve the problem. Computational results show that this approach finds good solutions within a short time, providing the production managers with practical approaches for this combined assignment and scheduling problem., We are grateful for the support by CAPES-Brazil and MEC-Spain (project CAPES-DGU258-12/PHB-0012-PC), by FAPERGS (project 12/2046-6), by Petrobras, by CNPq (project 478847/2013-0), and by the National Center for Supercomputing at UFRGS. We also thank the project "CORSARI MAGIC DPI2010-18243" of the Spanish Ministerio de Ciencia e Innovacion.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasound pre-treatment prior to unripe banana air-drying: effect of the ultrasonic volumetric power on the kinetic parameters

  • La Fuente-Arias, Carla Ivonne
  • Tadini, Carmen C.
[EN] Aiming to decrease the water content during the air-drying process of unripe banana slices, ultrasound (US) pre-treatments (25 °C) for 20 and 25 min at 9.38 and 25.63 W/L ultrasonic volumetric power were evaluated. Air-drying was performed at 50 and 60 °C for 360 min. Unripe banana slices pretreated at 25.63 W/L did not improve water migration, under either air-drying temperature, while slices pretreated at 9.38 W/L resulted in an increase in water effective diffusivity of 4.8 and 13.7% at 20 min US + air-drying at 50 °C and 25 min US + air-drying at 60 °C, respectively. The drying time saving of 7% and 9%, respectively, was achieved, showing that these treatments were alternative for processing unripe banana slices. Thus, ultrasound and air-drying operational parameters required accurately defined to achieve desirable results. Experimental data were adjusted to four models and the Midilli model resulted in the best experimental data fit, with r 2 > 0.9988, RMSE < 0.0873 and ¿2 < 0.00996., The authors acknowledge the financial support from the Sao Paulo Research Foundation (FAPESP) under Grants 2011/22398-0 and 2013/07914-8, the scholarship provided by the Coordination for the Improvement of Higher Education Personnel (CAPES, Finance Code 001) and by CNPq (National Council for Scientific and Technological Development) under Grant 306440/2013-0. Thanks to Prof. Antonio Carlos Teixeira (Dept. of Chemical Engineering, Escola Politecnica, University of Sao Paulo) for allowing the use of ultrasound bath (FISHER SCIENTIFIC, model FS 110, USA).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Behavior of metakaolin-based geopolymers incorporating sewage sludge ash (SSA)

  • Istuque, D.B.
  • Reig Cerdá, Lucía
  • Moraes, J.C.B
  • Akasaki, Jorge Luis
  • Malmonge, J.A.
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
[EN] In recent years, geopolymers have become a widely researched binding material. There are technological and environmental advantages tousing this type of binder instead of Portland cement. In this study, binary systems of geopolymers were produced by using mixtures of metakaolin (MK) ,a well-known aluminosilicate raw material, and a residue from sewage sludge incineration: sewage sludge ash (SSA). This ash was used to partially replace the metakaolin in proportions of 0 20%. The mixtures were activated with alkaline solutions and they were cured by using two different conditions: at room temperature (25 °C) and in a thermal bath (65 °C). The samples were assessed by X-ray diffraction, scanning electron microscopy (pastes) and compressive strength (mortars). The results from these studies showed zeolite formation (faujasite) in geopolymers cured in the thermal bath, which caused a decrease in the compressive strength of the alkali-activated mortars.Replacement of MK with SSA caused a lower reduction in the compressive strength of mortars cured at 65 °C. However, at room temperature, similar mechanical strength was observed for the MK and MK-SSA systems. These results demonstrated that SSA is a suitable mineral precursor for partial replacement of MK in geopolymer production., The authors acknowledge Santander Universidades for the grant to Lucia Reig (program: Becas lberoamerica Jovenes Profesores Investigadores Espana 2014), CAPES (CAPES/DGU no 266/12), CNPq (no. 14/2013 processo 478057/2013-0) Scanning electron microscopy service of FEIS/UNESP and CNPq (processo 309015/2015-4).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of the long-term compressive strength development of the sewage sludge ash/metakaolin-based geopolymer

  • Istuque, D.
  • Akasaki, J. L.
  • Melges, J. L. P.
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
[EN] This paper aimed to evaluate the long-term compressive strength development of the sewage sludge ash/metakaolin (SSA/MK)¿based geopolymer. SSA/MK¿based geopolymeric mortars and pastes were produced at 25ºC with different SSA contents (0 - 30 wt.%). Compressive strength tests were run within the 3-720 curing days range. A physicochemical characterisation (X-ray diffraction and scanning electron microscopy) was performed in geopolymeric pastes. All the geopolymeric mortars presented a compressive strength gain with curing time. The mortars with all the SSA evaluated contents (10, 20, 30 wt.%) developed a compressive strength over 40 MPa after 720 curing days at 25ºC. The maximum compressive strength of the mortars with SSA was approximately 61 MPa (10 wt.% of SSA), similarly to the reference mortar (100% MK-based geopolymer). The microstructure analyses showed that the SSA/MK¿based geopolymer presented a dense microstructure with N-A-S-H gel formation., This study was financed partly by the Coordenacao de Aperfeicoamento de Pessoal de Nivel Su-perior -Brasil (CAPES) -(Finance Code 001 and CAPES/DGU n. 266/12), and the National Council of Scientific and Technological Development -Bra-sil (CNPq) -(n. 14/2013, process 478057/2013-0 and 309015/2015-4). The authors would like to thank Programa Institucional de Internacionalizacao - CAPES -PrInt. The authors acknowledge the Scanning Electron Microscopy Service of FEIS/UN-ESP, Servico Municipal Autonomo de Agua e Es-goto (SEMAE) from the Sao Jose do Rio Preto city -SP, Brazil and Diatom Mineracao Ltda. The authors would like to thank Programa Institucional de Internacionalizacao CAPES -PrInt.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The assembly line worker assignment and balancing problem with stochastic worker availability

  • Ritt, Marcus
  • Costa, Alysson
  • Miralles Insa, Cristóbal Javier|||0000-0002-5269-9955
[EN] Assembly lines can be employed successfully in sheltered work centres to better include persons with disabilities in the labour market as well as to improve production efficiency. The optimal assignment of a heterogeneous workforce is known as the assembly line worker assignment and balancing problem (ALWABP). These assembly lines are characterised not only by a heterogeneous workforce, but also by high levels of absenteeism, which makes it more difficult to obtain stable and efficient line balancing solutions. In this paper, an extension of the ALWABP to minimise the expected cycle time under uncertain worker availability is proposed. We model this problem as a two-stage mixed integer program, and propose local search heuristics for solving it. Computational experiments show that stochastic modelling can help to improve the line's efficiency and that the proposed heuristics produce good results for instances of practical size., This work was supported by the CNPq under [grant number 478847/2013-0]; University of Melbourne under [grant number ECR 2015].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Quantifying usability of domain-specific languages: An empirical study on software maintenance

  • Albuquerque, Diego
  • Cafeo, Bruno
  • Garcia, Alessandro
  • Barbosa, Simone
  • Ribeiro, Antonio
  • Abrahao Gonzales, Silvia Mara|||0000-0003-3580-2014
A domain-specific language (DSL) aims to support software development by offering abstractions to a particular domain. It is expected that DSLs improve the maintainability of artifacts otherwise produced with general-purpose languages. However, the maintainability of the DSL artifacts and, hence, their adoption in mainstream development, is largely dependent on the usability of the language itself. Unfortunately, it is often hard to identify their usability strengths and weaknesses early, as there is no guidance on how to objectively reveal them. Usability is a multi-faceted quality characteristic, which is challenging to quantify beforehand by DSL stakeholders. There is even less support on how to quantitatively evaluate the usability of DSLs used in maintenance tasks. In this context, this paper reports a study to compare the usability of textual DSLs under the perspective of software maintenance. A usability measurement framework was developed based on the cognitive dimensions of notations. The framework was evaluated both qualitatively and quantitatively using two DSLs in the context of two evolving object-oriented systems. The results suggested that the proposed metrics were useful: (1) to early identify DSL usability limitations, (2) to reveal specific DSL features favoring maintenance tasks, and (3) to successfully analyze eight critical DSL usability dimensions., This work was funded by B. Cafeo CAPES PhD Scholarship, and CNPq scholarship grant number 141688/2013-0; A. Garcia FAPERJ - distinguished scientist grant (number E-26/102.211/2009), CNPq - productivity grants (number 305526/2009-0 and 308490/2012-6), Universal project grants (number 483882/2009-7 and 485348/2011-0), and PUC-Rio (productivity grant).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Unripe Banana Flour Produced by Air-Drying Assisted with Ultrasound-Description of the Mechanisms Involved to Enhance the Mass Transfer in Two Approaches

  • La Fuente-Arias, Carla Ivonne
  • Tadini, Carmen C.
[EN] In this research the application of ultrasound, prior to air-drying, describing the phenomena in two approaches: unripe banana slices immersed in water (hydrated) and vacuum packaged (non-hydrated) were investigated. The results showed two falling rate periods during the air-drying. For the second rate period, an increase of water effective diffusivity due to the "sponge effect" (direct effect of ultrasound) and the microscopic channels formation (indirect effect) was observed. Scanning electron microscopy images showed that untreated dried slices were less porous, characterized by small cavities and high density, while ultrasound pretreated slices resulted in a porous structure with more free volume between cells. An increase in porosity decreased the resistance for diffusion, influencing positively the water effective diffusivity. Moreover, ultrasound produced partial disorder of the crystalline structure within the starch granules, reducing the amount of energy required for gelatinization. Moreover, reduction of resistant starch content was not observed., The authors acknowledge financial support from the Sao Paulo Research Foundation (FAPESP) under grants 2011/22398-0 and 2013/07914-8, the scholarship provided by the Coordination for the Improvement of Higher Education Personnel (CAPES) and by CNPq (National Council for Scientific and Technological Development) under grant 306440/2013-0. Thanks for Prof. Elizabete Wenzel de Menezes and Aline de Oliveira Santos (Dept. of Food and Experimental Nutrition, Faculty of Pharmaceutical Sciences, University of Sao Paulo), for help with resistant starch analyses.
Repositori Institucional UIB
Publicación Artículo científico (JournalArticle)

Contribution of cardio-vascular risk factors to depressive status in the PREDIMED-PLUS Trial. A cross-sectional and a 2-year longitudinal study

  • Martín-Peláez, Sandra
  • Serra-Majem, Lluis
  • Cano-Ibáñez, Naomi
  • Martínez-González, Miguel Ángel
  • Salas-Salvadó, Jordi
  • Corella, Dolores
  • Lassale, Camille
  • Martínez, Jose Alfredo
  • Alonso-Gómez, Ángel M.
  • Wärnberg, Julia
  • Vioque, Jesús
  • Romaguera, Dora
  • López-Miranda, José
  • Estruch, Ramón
  • Tinahones, Francisco J.
  • Lapetra, José
  • Fernández-Aranda, Fernando
  • Bueno-Cavanillas, Aurora
  • Tur, Josep A.
  • Martín, Vicente
  • Pintó, Xavier
  • Delgado-Rodríguez, Miguel
  • Matía, Pilar
  • Vidal, Josep
  • Vázquez, Clotilde
  • Daimiel, Lidia
  • Ros, Emili
  • Toledo, Estefanía
  • Nishi, Stephanie K.
  • Sorli, Jose V.
  • Malcampo, Mireia
  • Zulet, M. Ángeles
  • Moreno-Rodríguez, Anaí
  • Cueto-Galán, Raquel
  • Vivancos-Aparicio, Diego
  • Colom, Antoni
  • García-Ríos, Antonio
  • Casas, Rosa
  • Bernal-López, M. Rosa
  • Santos-Lozano, Jose Manuel
  • Vázquez, Zenaida
  • Gómez-Martínez, Carlos
  • Ortega-Azorín, Carolina
  • Del Val, Jose Luís
  • Abete, Itziar
  • Goikoetxea-Bahon, Amaia
  • Pascual, Elena
  • Becerra-Tomás, Nerea
  • Chillarón, Juan J.
  • Sánchez-Villegas, Almudena
[eng] Background: Cardio-vascular disease and depression are thought to be closely related, due to shared risk factors. The aim of the study was to determine the association between cardio-vascular risk (CVR) factors and depressive status in a population (55–75 years) with metabolic syndrome (MetS) from the PREDIMED-Plus trial. Methods and findings: Participants were classified into three groups of CVR according to the Framingham-based REGICOR function: (1) low (LR), (2) medium (MR) or (3) high/very high (HR). The Beck Depression Inventory-II (BDI-II) was used to assess depressive symptoms at baseline and after 2 years. The association between CVR and depressive status at baseline (n = 6545), and their changes after 2 years (n = 4566) were evaluated through multivariable regression models (logistic and linear models). HR women showed higher odds of depressive status than LR [OR (95% CI) = 1.78 (1.26, 2.50)]. MR and HR participants with total cholesterol <160 mg/mL showed higher odds of depression than LR [OR (95% CI) = 1.77 (1.13, 2.77) and 2.83 (1.25, 6.42) respectively)] but those with total cholesterol ≥280 mg/mL showed lower odds of depression than LR [OR (95% CI) = 0.26 (0.07, 0.98) and 0.23 (0.05, 0.95), respectively]. All participants decreased their BDI-II score after 2 years, being the decrease smaller in MR and HR diabetic compared to LR [adjusted mean±SE = -0.52±0.20, -0.41±0.27 and -1.25±0.31 respectively). MR and HR participants with total cholesterol between 240–279 mg/mL showed greater decreases in the BDI-II score compared to LR (adjusted mean±SE = -0.83±0.37, -0.77±0.64 and 0.97±0.52 respectively). Conclusions: Improving cardiovascular health could prevent the onset of depression in the elderly. Diabetes and total cholesterol in individuals at high CVR, may play a specific role in the precise response. International Standard Randomized Controlled Trial (ISRCTN89898870).
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

The Concreteness Advantage in Lexical Decision Does Not Depend on Perceptual Simulations

  • Bottini, Roberto
  • Morucci, Piermatteo
  • D’Urso, Anna
  • Collignon, Olivier
  • Crepaldi, Davide
Online First Publication, September 9, 2021, Abstract words are typically more difficult to identify than concrete words in lexical-decision, word-naming, and recall tasks. This behavioral advantage, known as the concreteness effect, is often considered as evidence for embodied semantics, which emphasizes the role of sensorimotor experience in the comprehension of word meaning. In this view, online sensorimotor simulations triggered by concrete words, but not by abstract words, facilitate access to word meaning and speed up word identification. To test whether perceptual simulation is the driving force underlying the concreteness effect, we compared data from early-blind and sighted individuals performing an auditory lexical-decision task. Subjects were presented with property words referring to abstract (e.g., “logic”), concrete multimodal (e.g., “spherical”), and concrete unimodal visual concepts (e.g., “blue”). According to the embodied account, the processing advantage for concrete unimodal visual words should disappear in the early blind because they cannot rely on visual experience and simulation during semantics processing (i.e., purely visual words should be abstract for early-blind people). On the contrary, we found that both sighted and blind individuals are faster when processing multimodal and unimodal visual words compared with abstract words. This result suggests that the concreteness effect does not depend on perceptual simulations but might be driven by modality-independent properties of word meaning., This research was supported in part by the Research Projects of National Relevance (PRIN) grant “How Do We Make Sense of Words?” (Project Grant 2015PCNJ5F) awarded to Davide Crepaldi and Olivier Collignon by the Italian Ministry of Education, the European Research Council (ERC) grant “MADVIS—Mapping the Deprived Visual System: Cracking Function for Prediction” (Project 337573, ERC-20130StG), and the Belgian Excellence of Science (EOS) program (Project 30991544) awarded to Olivier Collignon.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Polyoxometalate-ionic liquids (POM-ILs) – a new type of ionic liquid additive family for lubricants

  • Casasin-Garcia, M. L.
  • Khanmohammadi, H.
  • Mitchell, S. G.
  • Espallargas, N.
The focus on energy efficiency to move towards a more sustainable use of resources has intensified efforts to minimize friction and wear in mechanical systems, which account for 23% of the world's energy consumption. In this study, polyoxometalate ionic liquids (POM-ILs) are introduced as environmentally acceptable lubricant additives, for their potential friction-reducing and anti-wear (AW) properties. These compounds, characterized by their complex structures and tunable properties, have been investigated for their tribological performance across base fluids of varying polarities. Their performance has been compared against zinc dialkyldithiophosphate (ZDDP), a standard AW additive. Our findings demonstrate that POM-ILs exhibit promising friction-reducing and AW capabilities, comparable to traditional additives. The efficacy of POM-ILs was found to be highly dependent on the base fluid used, with significant variations observed in their ability to interact with stainless steel surfaces. Adsorption studies confirmed strong adsorption of POM-ILs onto stainless steel, with notable influence from the base fluid. Advanced characterization techniques revealed the formation of a predominantly oxide-rich tribofilm on the metal surface, as a result of POM-IL decomposition and reaction with the metal. POM-ILs show significant potential as lubricant additives, with their structural versatility offering a promising path for future greener developments in tribology.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Multifunctional polyoxomolybdate ionic liquid coatings for mitigating microbiologically influenced corrosion

  • Malefioudaki, Mariella
  • Misra, Archismita
  • Sbeity, Nadja
  • Zueco-Vincelle, Juan
  • Laguna-Bercero, Miguel A.
  • Koerdt, Andrea
  • Martín-Rapún, Rafael
  • Mitchell, Scott G.
Corrosion of metals and other materials in marine environments poses significant economic, operational, safety, and environmental challenges across the oil and gas industry, the renewable energy sector, and maritime infrastructure. Microbiologically influenced corrosion (MIC) accounts for a substantial portion of this corrosion, with sulfate-reducing bacteria (SRB) and methanogenic archaea (MA) being key contributors. Conventional methods such as cathodic polarization have proven insufficient in mitigating the colonization of corrosive microbial communities in real marine environments, requiring the development of alternative, broad-spectrum antimicrobial strategies to prevent such biofilm formation. Recently, molybdate has emerged as a potential alternative to traditional biocides and nitrate. Our hypothesis is polyoxometalate-ionic liquids (POM-ILs), which exhibit antimicrobial and anticorrosion properties, could have a broader spectrum of antimicrobial activity than demonstrated until now and could be capable of shielding and protecting sensitive metal surfaces from the extreme acidic environments produced by MIC microorganisms. Here we show how two prototype polyoxomolybdate-based POM-ILs, [(CH3(CH2)6)4N]2[Mo6O19] and [(CH3(CH2)6)4N]4[Mo8O26], demonstrated antimicrobial activity at microgram per millilitre concentrations, prevented biofilm formation on metal surfaces, and provided resistance to corrosive acidic environments. Furthermore, impedance measurements were commensurate with electron microscopy studies showing that POM-IL-coated brass coupons withstood extremely corrosive environments. These proof-of-concept results demonstrate how multi-functional POM-IL coatings represent promising MIC mitigation solutions by providing a hydrophobic acid-resistant and biocidal protective layer that prevents biocolonisation and acidic corrosion by MIC microorganisms.