Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 26
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Cobalt-Zirconia coated monoliths fabricated by Direct Ink Writing for catalytic applications

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, Miguel Ángel
  • Llanes, Luis
  • Llorca, Jordi
  • Morales, Miguel
Direct Ink Writing (DIW) is a promising technique for fabricating ceramic catalysts with complex geometries and enhanced catalytic performances, but these still require overcoming some challenges to maximize their catalytic and mechanical functionality. In this work, DIW yttria-doped zirconia (YDZ) catalysts were coated with a Co/YDZ catalyst layer. Two configurations based on a dense monolith and a porous one sintered at 1450ºC and 1300ºC were fabricated through DIW, using optimal rheological hydrogel-inks, to investigate the effect of porosity on the mechanical and catalytic performance in the ethanol steam reforming reaction. The monolith sintered at 1450°C achieved the best mechanical and catalytic performance, as it presented the highest Co concentration (2.3 at%) at the catalyst layer. In addition, this monolith exhibited excellent mechanical properties at the interface between contiguous filaments in the multilayer structure. Therefore, this simple approach is a promising method to produce enhanced catalytically and mechanically robust monoliths.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

La pretendida gratuidad del procedimiento económico-administrativo: especial referencia al régimen jurídico de las costas en el mencionado procedimiento

  • Álvarez Martínez, Joaquín
Si bien la normativa tributaria proclama, en un primer instante, la gratuidad del procedimiento económico-administrativo, la realidad demuestra que existen serias dudas de la certeza de dicha afirmación. En el presente trabajo se examinan, desde una perspectiva jurídica, los diferentes costes que pueden llegar a asumir quienes, en defensa de sus derechos e intereses legítimos, acuden a la vía económico-administrativa, prestando una especial atención, a estos efectos, al régimen jurídico por el que se rigen las costas del mencionado procedimiento.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Magnetic Field Screening of 2D Materials Revealed by Magnetic Force Microscopy

  • Aldave, Diego A.
  • López-Polín, Guillermo
  • Calle, Esther
  • Begué, Adrián
  • Ranchal, Rocío
  • Martínez, Raúl
  • Bran, Cristina
  • Burzurí, Enrique
  • Gómez-Herrero, Julio
  • Ares, Pablo
  • Jaafar, Miriam
2D materials possess exceptional mechanical properties making them promising candidates for protecting nanostructures. However, the magnetic field screening properties of 2D materials are largely unexplored. Here it is used Magnetic Force Microscopy (MFM) to unveil the effects on the magnetic field of magnetic nanostructures when 2D materials are placed on top of them. It is demonstrated that while graphene exhibits a weak diamagnetic response due to its unique electronic structure around the Dirac point, the overall screening effect remains minimal (≈0.5% per layer). Conversely, graphene oxide (GO) and MoS2 show negligible response to the magnetic field, making them ideal for applications where preserving the original magnetic properties is crucial. These findings suggest that 2D materials can offer effective protection while minimally affecting the underlying magnetic functionalities, important for data storage technologies and spintronics.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Direct Ink Writing of cobalt-zirconia monoliths for catalytic applications: A novel single-step fabrication approach

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Vilella, Tània
  • Serrano, Isabel
  • Laguna-Bercero, Miguel Ángel
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Additive manufacturing technologies are revolutionizing the fabrication of ceramic catalysts through hierarchical design to enhance catalytic performance and simultaneously improving the efficiency of the manufacturing process by decreasing the initial investment and production steps. This work proposes a fabrication process of cobalt-zirconia monoliths based on Direct-Ink Writing of Co-enriched hydrogel-based ceramic inks, and the debinding and sintering at 600ºC in a single thermal treatment. The effect of Co precursor amount (3.0 −7.0 wt% Co) on the rheological properties of inks and the catalytic performance in ethanol steam reforming is investigated. The results reveal the successful incorporation of Co into rectilinear monoliths with 50 % infill, obtaining strongly Co-rich surfaces. The remarkable catalytic performance of the 5.0 wt% Co monolith at 300–600ºC confirms the feasibility of this novel single-step approach, reaching an appropriate balance between catalytic activity and printability. This outcome may represent a push towards the fabrication of fully 3D-printed monolithic catalysts.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Xylem and Phloem in Petioles Are Coordinated With Leaf Gas Exchange in Oaks With Contrasting Anatomical Strategies Depending on Leaf Habit

  • Martín-Sánchez, Rubén
  • Sancho-Knapik, Domingo
  • Ferrio, Juan Pedro
  • Alonso-Forn, David
  • Losada, Juan Manuel
  • Peguero-Pina, José Javier
  • Mencuccini, Maurizio
  • Gil-Pelegrín, Eustaquio
As the single link between leaves and the rest of the plant, petioles must develop conductive tissues according to the water influx and sugar outflow of the leaf lamina. A scaling relationship between leaf area and anatomical traits of xylem and phloem is expected to improve the efficiency of these tissues. However, the different constraints compromising the functionality of both tissues (e.g., risk of cavitation) must not be disregarded. Additionally, deciduous and evergreen plants may have different strategies to produce and package their petiole conduits to cope with environmental restrictions. We explored in 33 oak species the relationships between petiole anatomical traits, leaf area, stomatal conductance, and photosynthesis rate. Results showed allometric scaling between anatomical structure of xylem and phloem with leaf area. We also found correlations between photosynthesis rate, stomatal conductance, and anatomical traits in the petiole. The main novelty is how oaks present a different strategy depending on the leaf habit. Deciduous species tend to increase their diameters to achieve greater leaf‐specific conductivity. By contrast, evergreen oaks develop larger xylem conductive areas for a given leaf area than deciduous ones. This trade‐off between safety‐efficiency in petioles has never been attributed to the leaf habit of the species.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effects of feed additives in the diet of male dairy beef calves on physiological status and rumen microbial fermentation pre- and postweaning

  • Romera-Recio, E.
  • Ramos-Morales, E.
  • Belanche, A.
  • Hassan, M.
  • Romero, P.
  • Gómez, A.
  • Rivelli, I.
  • Llanes, N.
  • Torra, J.
  • Yáñez-Ruiz, D.R.
n Spain, a large number of unweaned calves from northern Europe's dairy industry are transported for intensive beef production, which could pose health risks around weaning due to the separation from their mothers. This study evaluated the impact of including different feed additives in starter concentrate on blood parameters and rumen functional development in 112 calves at the growing farm. We hypothesized that feed additives could enhance rumen function and mitigate health risks associated with transportation and intensive management. The treatments tested, against a control diet (CTL), included: blend of essential oils from plant extracts (EO), yeast-based products (SYN) and a mix of yeast probiotics, oregano-based essential oil and sodium butyrate (MIX). Each treatment was administered during the preweaning stage, with all calves transitioning to the MIX diet postweaning. In the experiment, blood and rumen samples were collected before weaning (8 weeks old) and two months after weaning (18 weeks old) for rumen fermentation and microbial population analyses. Calves were weighed upon arrival (3 weeks), at weaning (10 weeks) and two months postweaning (18 weeks) to assess performance. Results from the experiment showed that rumen fermentation profiles remained stable with regard to volatile fatty acids (VFA) concentrations and pH, indicating effective solid feed consumption and microbial activity before weaning. Postweaning, all feed additives treatments improved rumen fermentation by increasing total VFA and lowering pH, though body weight gains remained unaffected. Concentrations of bacteria and archaea increased compared to preweaning levels, protozoa were absent, and anaerobic fungi did not become established until 2 months postweaning. In conclusion, feed additives provided preweaning improved rumen development, although they did not increase productivity. The treatment should be applied preweaning, highlighting the importance of this particular window of time.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Stress and telomere length in leukocytes: Investigating the role of GABRA6 gene polymorphism and cortisol

  • Martino, Pablo
  • Perez-Alarcón, Mario
  • Deconinck, Luna
  • De Raedt, Rudi
  • Vanderhasselt, Marie-Anne
  • Kozusznik, Malgorzata W.
  • Kooy, Frank
  • Hidalgo, Vanesa
  • Venero, César
  • Salvador, Alicia
  • Baeken, Chris
  • Pulopulos, Matias M.
Telomere length (TL) is considered a biomarker of aging, and short TL in leukocytes is related to age and stress-related health problems. Cumulative lifetime stress exposure has also been associated with shorter TL and age-related health problems, but the mechanisms are not well understood. We tested in 108 individuals whether shorter TL in leukocytes is observed in individuals with the GABRA6 TT genotype, which has been associated with dysregulation of hypothalamic-pituitary-adrenal axis activity (the main biological stress system) compared to the CC genotype. We also investigated if individuals carrying the TT genotype show higher stress-induced and diurnal cortisol secretion and if cortisol explains the interindividual variability in TL. The analysis pipeline of this study was pre-registered, and the results showed that GABRA6 TT carriers had shorter TL in CD8+CD28+ cells (Bonferroni corrected). In contrast to previous studies, no differences between groups in cortisol secretion were observed, and TL and cortisol did not show significant associations. This study shows, for the first time, shorter TL in CD8+CD28+ cells in TT carriers for GABRA6 compared to CC carriers, suggesting accelerated cellular aging. Although this difference could be linked to an increased susceptibility to stress in the TT carriers, this could not be attributed to the direct influence of cortisol, suggesting the involvement of other mechanisms.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Multimodal antiproliferative effects of oleanolic acid mitocans: In vitro and in vivo studies

  • Puerta, Adrián
  • González-Bakker, Aday
  • Romanos, Eduardo
  • Domínguez, Inmaculada Aguilar
  • Martínez-Montiel, Mónica
  • Merino-Montiel, Penélope
  • Pérez Herrera, Raquel
  • Gimeno Floría, M. Concepción
  • Fernández-Bolaños, José G.
  • López, Óscar
  • Padrón, José M.
Mitochondria-targeting drugs (mitocans) based on organic cations are emerging as powerful and selective cancer therapeutics. In this study, we have evaluated a novel series of oleanolic acid-derived mitocans, revealing nanomolar-range antiproliferative effects against human solid tumor cells. Continuous live-cell imaging revealed extensive cytoplasmic vacuolation, while mechanistic studies identified paraptosis as the dominant form of cell death. Remarkably, in vivo experiments demonstrated significant tumor growth inhibition in mice, with no detectable toxicity at therapeutic doses. These findings highlight the potential of oleanolic acid-derived mitocans as promising candidates for cancer therapy.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

High performance La2NiO4+δ oxygen and Ni–Ce0.9Gd0.1O2−δ fuel electrodes for thin film reversible solid oxide cells

  • Riaz, Adeel
  • Sirvent, Juande
  • Zueco-Vincelle, Juan
  • Buzi, Fjorelo
  • Panisset, Silvère
  • Stangl, Alexander
  • Rapenne, Laetitia
  • Baiutti, Federico
  • Mermoux, Michel
  • Laguna-Bercero, Miguel Angel
  • Tarancón, Albert
  • Burriel, Mónica
Thin film reversible solid oxide cells (TF-rSOCs) are attracting a great deal of interest as they promise to operate at much lower temperatures (400–600 °C) than state-of-the-art commercial fuel electrode-supported cells (600–800 °C). However, in all-ceramics TF-rSOCs the high polarization resistance of the electrodes limits the cell performance. To overcome this limitation, high performing oxygen and fuel electrodes were selected and their nanostructure was optimized. Thin nanoporous films of La2NiO4+δ were deposited as oxygen electrode by Pulsed Injection Metal Organic Chemical Vapor Deposition (PI-MOCVD) with different thickness. As for the fuel electrode, thin films of Ni–Ce0.9Gd0.1O2−δ (NiCGO) were deposited by Pulsed Laser Deposition (PLD) at various temperatures and pO2. The electrochemical activity of the oxygen and fuel electrodes was measured by Electrical Conductivity Relaxation (ECR) and Electrochemical Impedance Spectroscopy (EIS), respectively. The optimized electrodes were then deposited on a YSZ single crystal electrolyte and the cell was measured in fuel cell and electrolysis modes showing high performance with a power density of 70 mW cm−2 at 0.7 V and a current density of −44 mA cm−2 at 1.3 V at a low operating temperature of 600 °C. These results demonstrate the potential of using these materials as electrodes in TF-rSOCs.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Multifunctional polyoxomolybdate ionic liquid coatings for mitigating microbiologically influenced corrosion

  • Malefioudaki, Mariella
  • Misra, Archismita
  • Sbeity, Nadja
  • Zueco-Vincelle, Juan
  • Laguna-Bercero, Miguel A.
  • Koerdt, Andrea
  • Martín-Rapún, Rafael
  • Mitchell, Scott G.
Corrosion of metals and other materials in marine environments poses significant economic, operational, safety, and environmental challenges across the oil and gas industry, the renewable energy sector, and maritime infrastructure. Microbiologically influenced corrosion (MIC) accounts for a substantial portion of this corrosion, with sulfate-reducing bacteria (SRB) and methanogenic archaea (MA) being key contributors. Conventional methods such as cathodic polarization have proven insufficient in mitigating the colonization of corrosive microbial communities in real marine environments, requiring the development of alternative, broad-spectrum antimicrobial strategies to prevent such biofilm formation. Recently, molybdate has emerged as a potential alternative to traditional biocides and nitrate. Our hypothesis is polyoxometalate-ionic liquids (POM-ILs), which exhibit antimicrobial and anticorrosion properties, could have a broader spectrum of antimicrobial activity than demonstrated until now and could be capable of shielding and protecting sensitive metal surfaces from the extreme acidic environments produced by MIC microorganisms. Here we show how two prototype polyoxomolybdate-based POM-ILs, [(CH3(CH2)6)4N]2[Mo6O19] and [(CH3(CH2)6)4N]4[Mo8O26], demonstrated antimicrobial activity at microgram per millilitre concentrations, prevented biofilm formation on metal surfaces, and provided resistance to corrosive acidic environments. Furthermore, impedance measurements were commensurate with electron microscopy studies showing that POM-IL-coated brass coupons withstood extremely corrosive environments. These proof-of-concept results demonstrate how multi-functional POM-IL coatings represent promising MIC mitigation solutions by providing a hydrophobic acid-resistant and biocidal protective layer that prevents biocolonisation and acidic corrosion by MIC microorganisms.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Injectable borax-loaded alginate hydrogels reduce muscle atrophy, modulate inflammation, and promote neuroprotection in the SOD1G93A mouse model of ALS through mechanisms involving IGF–Akt–mTOR signaling

  • Rodriguez-Romano, Ana
  • Gonzalez-Valdivieso, Juan
  • Moreno-Martinez, Laura
  • Vázquez Costa, Juan Francisco
  • Osta, Rosario
  • Rico, Patricia
Amyotrophic Lateral Sclerosis (ALS) is a prevalent condition characterized by motor neuron loss and skeletal muscle paralysis. Despite being associated to mutations in over 40 genes, its etiology remains elusive without a cure or effective treatment. ALS, historically considered a motor neuron disease, is defined today as a multisystem disorder involving non-neuronal cell types, including early muscle pathology independent of motor neuron degeneration (dying back hypothesis), thus skeletal muscle actively contributes to disease pathology, making it a viable therapeutic target for ALS. Our previous research has shown that boron transporter NaBC1 (encoded by the SLC4A11 gene), after activation co-localizes with integrins and growth factor receptors synergistically enhancing muscle repair. Here we investigate the effects of injectable alginate-based hydrogels for controlled local borax release in Amyotrophic Lateral Sclerosis muscle. Treated mice showed improved motor function, prolonged survival, and activation of essential muscle metabolic pathways, leading to enhanced muscle repair and reduced atrophy and inflammation. Interestingly, local muscle repair activation provided retrograde neuroprotection by preserving motor neurons and reducing neuro-inflammation. This study highlights the role of muscle tissue in ALS pathology, supporting its targeting with NaBC1-based therapies for muscle regeneration.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Praseodymium and gadolinium doped ceria as oxygen electrode for solid oxide cell applications

  • Morales-Zapata, Miguel Ángel
  • Larrea, Ángel
  • Laguna-Bercero, Miguel Ángel
his study analyzes the structural and electrochemical properties of praseodymium- and gadolinium-doped ceria (CPGO) samples formed by the sintering reaction of Pr2NiO4+δ (PNO) and Ce0.9Gd0.1O2−δ (GDC). X-ray powder diffraction analysis confirmed a single-phase cubic CPGO structure as a primary phase. The cationic compositions were determined using energy dispersive spectroscopy (EDS) in a scanning transmission electron microscope (STEM), while core-loss electron energy-loss spectroscopy (EELS) was used to determine the valence of Ce and Pr. The compatibility between thermal expansion coefficients validated their integration with electrolytes at the typical Solid Oxide Cell (SOC) operation temperatures. Oxygen chemical diffusion and surface exchange coefficients were investigated using the electrical conductivity relaxation (ECR) method at intervals of partial oxygen pressures between 0.10 and 0.21 atm and 600 °C and 800 °C. Finally, the samples were tested in symmetrical cells by electrochemical impedance spectroscopy (EIS) between 700 °C and 850 °C. A polarization resistance of 0.17 Ω cm2 at 850 °C was obtained for CPGO air electrodes formed by sintering a mixture of 80% by weight of GDC and 20% by weight of PNO. These findings confirm that PNO–GDC mixtures forming CPGO oxides are excellent candidates for SOC applications. En este estudio se analizan las propiedades estructurales y electroquímicas de composites formados por la reacción de sinterización de Pr2NiO4+δ (PNO) y Ce0.9Gd0.1O2-δ (GDC). Los refinamientos de Rietveld de los patrones de difracción de rayos X confirmaron una estructura cúbica monofásica de ceria dopada con praseodimio y gadolinio (CPGO) como fase primaria. Las composiciones catiónicas de CPGO se determinaron mediante espectroscopia de dispersión de energía (EDS) en un microscopio electrónico de transmisión de barrido (STEM), mientras que se utilizó espectroscopia de pérdida de energía de electrones (EELS) para determinar la valencia de Ce y Pr. La compatibilidad entre coeficientes de expansión térmica validó la integración de los electrodos con electrolitos a las temperaturas de operación típicas de las pilas de óxido sólido (SOC). Los coeficientes de difusión química de oxígeno y de intercambio superficial se determinaron mediante relajación de la conductividad eléctrica (ECR). Finalmente, se caracterizaron celdas simétricas mediante espectroscopia de impedancia electroquímica (EIS), obteniendo una baja resistencia de polarización de 0.17 Ω cm2 a 850 °C para electrodos de aire compuestos por 80% de GDC y 20% de PNO en peso. Estos hallazgos confirman que los electrodos de CPGO son excelentes candidatos para aplicaciones SOC.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

3D-printed Ni/γ-Al2O3 catalysts for CO2 methanation: Effect of Ni loading and sintering temperature

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, Miguel Ángel
  • Vilella, Tània
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Additive manufacturing (AM) technologies are revolutionizing the production of ceramic components, particularly in fields like catalysis, where complex shapes offer remarkable advantages in performance. AM also minimizes material waste while reducing the number of fabrication steps. This work is focused on the fabrication of Ni/γ-Al2O3 monoliths for CO2 methanation in one step by using Direct-Ink Writing (DIW) of Ni-enriched hydrogel-based γ-Al2O3 inks, and the debinding and sintering in a single thermal treatment. For this purpose, the influence of Ni precursor amount (2.5–5.0 wt% Ni) on the rheological properties of inks and the catalytic activity is investigated. Monoliths with woodpile architecture and 50 % infill are sintered at 450 °C and 600 °C to determine the effect of the sintering temperature on the Ni distribution in the catalyst. Results evidence successful incorporation of the metallic active phase into the monolithic structures. Both the Ni amount and sintering temperature are key factors to enhance the CO2 methanation performance. The 5.0 wt% Ni monolith sintered at 450 °C presents both the highest CO2 conversion and methane selectivity at 350–500 °C, due to better reduction degree, dispersion, and smaller size of Ni nanoparticles at the maximum metal loading. These remarkable results demonstrate the potential of DIW for the fabrication of fully 3D-printed monolithic catalysts with well-dispersed metal particles, all while minimizing production steps.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Direct recycling of 3D-printed Co-YDZ catalysts for ethanol steam reforming

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, Miguel Ángel
  • Vilella, Tània
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Additive manufacturing enhances the catalyst performance via hierarchical design. To address environmental and resource concerns, this work aims to fabricate directly recycled 3D-printed monoliths using Direct-Ink Writing (DIW) from 100 % recovered cobalt-zirconia powders. Virgin cobalt-zirconia monoliths were firstly fabricated by DIW of 3.0–7.0 wt% Co-enriched hydrogel-based ceramic inks, followed by calcination at 600°C in a single thermal treatment. After testing the catalytic performance of monoliths in ethanol steam reforming, 3D-printed cobalt-zirconia monoliths were fragmented and subjected to subsequent milling and sieving steps to recover composite cobalt-zirconia powders with the appropriate properties for reuse in DIW. The recovered powders, inks and monoliths were microstructurally, rheologically and catalytically characterized, and then compared to catalysts constituted by virgin materials. The rheology properties of inks for the recycled and virgin monoliths presented an appropriate printability. Furthermore, the catalytic performance of recycled monoliths was close to that exhibited by virgin catalysts. This study demonstrates the feasibility of directly recycling fully 3D-printed catalysts, potentially reducing the environmental impact with a circular production model to enhance sustainability in the catalyst industry.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

In vitro screening of essential oil blends, probiotics and prebiotics to optimize post‐weaning in artificially reared ruminants: effects on rumen fermentation and gut health indicators in Caco‐2 cells

  • Muñoz-Grein, Jennifer
  • López, Rut
  • Solanas, Estela
  • Fondevila, Manuel
  • Belanche, Alejandro
BACKGROUND: Weaning represents a significant digestive challenge for dairy ruminants due to their underdeveloped rumenmicrobiota resulting from early separation from their dams shortly after birth. This study aimed to optimize the weaning pro-cess by evaluating six commercial feed additives, including four blends of essential oils (BEOs), a probiotic (live yeast) and a pre-biotic (pectin). The effects on rumen fermentation were evaluated using batch cultures with rumen inocula collected at thepost-weaning period from artificially reared lambs, whereas the effects on gut health indicators were assessed using Caco-2 cellmonolayers.RESULTS: Most tested additives showed minor benefits on rumen fermentation, even at higher doses (600 mg L−1 ). A BEO con-taining turmeric, thymol and yeast cell wall promoted a shift towards propionic fermentation, whereas supplementation withpectin decreased NH3 -N concentrations. Conversely, all four BEOs positively influenced intestinal health, resulting in improvedCaco-2 cell viability and lower levels of pro-inflammatory interleukin-6.CONCLUSION: Modulating rumen fermentation during the post-weaning in artificially reared lambs is challenging due to theirimmature rumen microbiota, absence of protozoa, and low rumen pH. Nevertheless, this in vitro study suggests that certainBEOs may enhance intestinal health by improving cell viability and reducing inflammation. Further in vivo studies are neededto confirm these findings.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Otros (Other)

Editorial: Unravelling the unknown of the rumen microbiome: implications for animal health, productivity, and beyond

  • Belanche, Alejandro
  • Belzecki, Grzegorz
  • Hernandez-Sanabria, Emma
  • Martínez-Fernandez, Gonzalo
  • Ramos-Morales, Eva
  • de la Fuente, Gabriel
The rumen, a highly specialised fermentation chamber within the digestive systems of ruminant animals, harbours a complex and dynamic microbial ecosystem. This intricate consortium of bacteria, archaea, protozoa, and fungi plays a central role in the degradation and fermentation of fibrous plant material, ultimately converting it into absorbable nutrients and energy for the host. Beyond its fundamental role in nutrient metabolism, the rumen microbiota exerts profound effects on animal health, immunity, productivity, and environmental sustainability. Understanding its structure and function is therefore critical not only for improving livestock production but also for advancing sustainable agricultural systems in the face of global challenges such as climate change and food security...
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

In vitro effects of saponins, tannins and lipids on rumen fermentation and intestinal health markers in a ruminant weaning context

  • Muñoz-Grein, Jennifer
  • Solanas, Estela
  • Fondevila, Manuel
  • Belanche, Alejandro
Dairy ruminants often experience physiological disturbances during the post-weaning, includingsuboptimal rumen fermentation due to an underdeveloped rumen microbiota, and diarrhoeaassociated with intestinal inflammation and oxidative stress. This study explored six commercialfeed additives with a potential dual mode of action to optimise both rumen fermentation andintestinal health in a post-weaning scenario. The experimental treatments included dietary sup-plementation with saponins (SAP), tannins (TAN), lauric acid (LAU), fish oil (FIO), high-unsaturatedolein (HUO) and high-saturated olein (HSO). Additives were tested at four doses (0, 100, 300 and600 mg/L) with four experimental replicates. Effects on rumen fermentation were evaluated inbatch cultures using inocula from dairy lambs and a high concentrate substrate, while intestinalhealth responses were evaluated in Caco-2 cells. Saponins (p ¼ 0.01) and tannins (p < 0.01) lin-early decreased rumen ammonia-N concentration in batch cultures. In Caco-2 cells, saponinsimproved metabolic activity (p ¼ 0.04), whereas tannins reduced pro-inflammatory IL-6 concentra-tion (p < 0.01), suggesting beneficial effects on intestinal health. Lipid sources exerted minimaleffects on rumen fermentation and induced intestinal inflammation when supplemented at highdoses. Overall, the physiological constrains of dairy ruminants during the post-weaning period,such as an immature rumen microbiota, absence of protozoa and low rumen pH, may limit theefficacy of additives in improving rumen fermentation. Nevertheless, saponins and tanninsshowed potential to reduce rumen proteolysis and support intestinal health during this criticaldevelopmental stage. Further in vivo research is required to validate these findings.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A prospective review on bioplastics and biopolymers

  • Moreira, Rui
  • Atienza-Martínez, Maria
  • Gil-Lalaguna, Noemí
  • Serra, Arménio
  • Cornejo, Alfonso
  • Bimbela, Fernando
  • Coelho, Jorge
  • Gandía, Luis M.
  • Arauzo, Jesus
  • Sánchez, José Luis
The production of bioplastics has been extensively investigated in recent decades, with the purpose of reducing the global dependence on fossil resources. In this review, the main routes to produce bioplastics and a critical discussion of these technologies are presented. The synthesis routes to produce biodegradable and non-biodegradable bioplastics are discussed. Additionally, approaches to improve the environmental footprint of some conventional plastics that have no immediate solutions of substitution are also addressed. A comparison of the main properties of the bioplastics considered and a general perspective of the bioplastics market are also provided. Because these themes have often been reviewed separately, this article aims to provide a unified general perspective of bioplastics in the context of a biobased economy, as well as pointing out some of the hurdles in such way.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

BBN bounds on neutrinophilic ultralight Dark Matter

  • Bertólez-Martínez, T.
  • López-Sarrión, J.
  • Salvado, J.
The high densities in the early Universe provide a unique laboratory to constrain couplings between feebly interacting particles, such as dark matter and neutrinos. In this article, we study how Big Bang Nucleosynthesis can constrain models of Ultra-Light Dark Matter diagonally coupled to neutrinos. We follow an adiabatic formalism which allows to average-out the rapid oscillations of the Dark Matter field and consistently take into account the feedback between the neutrino and the Dark Matter fields. This feedback alters the early Universe dynamics, causing the Dark Matter energy density to scale as radiation, while the neutrino mass scales as a −1 . These two effects modify primordial element abundances by modifying interaction rates and the expansion rate during nucleosynthesis. Then, we use primordial abundances to obtain leading cosmological bounds on the coupling in the range mϕ/eV ∈ (10−22, 10−17), namely g ≲ 0.13(mϕ/eV) for mϕ ≳ 3 × 10−20 eV and g ≲ 1.8 × 10−11q mϕ/eV for mϕ ≲ 3 × 10−20 eV. This consistent cosmological treatment emphasizes that, in the mass interval where its physical assumptions hold, neutrino masses cannot be generated refractively by a direct coupling with an Ultra-Light Dark Matter field.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Structural analysis of Pb-based organic–inorganic metal halide perovskites modified with Cetyltrimethylammonium bromide and 2-Aminopyrazine: Effects on stability and band gap

  • Tabares, Laurenth G.
  • Salamanca-Perdigón, Kevin
  • Lozano, Johan D.
  • Téllez, Jhoan F.
  • Laguna-Bercero, Miguel Á.
  • Macías, Mario A.
The synthesis of the hybrid organic–inorganic metal halide perovskites (C19H42N)3Pb2Cl7, (C19H42N)3Pb2Br7, (C4H7N3)2Cl2PbCl4, and (C4H7N3)2Br2PbBr4 is reported. These Pb-based structures were obtained using cetyltrimethylammonium bromide (CTAB) and 2-aminopyrazine (2-APZ) as organic precursors, respectively. Single-crystal X-ray diffraction analysis revealed that the asymmetric unit for CTAB-based compounds contains three [(C16H33)N(CH3)3]+ cations and a dinuclear [Pb2Cl7]3− unit composed of two lead-centered coordination polyhedra. In contrast, the 2-APZ-based compounds show [PbCl6]4− octahedra connected through vertex sharing to form layered structures alternating with organic [C4H7N3]2+ cations. In both cases, substitution of Cl by Br produced isostructural compounds, but changed the band gap values: from 3.6 eV to 3.3 eV for CTAB-based perovskites and from 2.5 eV to 2.1 eV for 2-APZ-based perovskites. Despite their lower band gap, the 2-APZ-derived compounds exhibited poor ambient stability. Conversely, CTAB-based compounds, although having a higher band gap, demonstrated enhanced thermal and environmental stability due to their hydrophobic nature. The different molecular sizes between 2-APZ and CTAB created different space between inorganic sheets leading to different quantum confinement. These findings highlight the potential for designing improved materials with both low band gap and high stability through mixed occupancy of different organic molecules.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effects of Colostrum Source, Dose and Processing on In Vitro Rumen Fermentation in Weaned Lambs

  • Muñoz-Grein, Jennifer
  • Chekikene, Amina Hind
  • Graikini, Dimitra
  • Sánchez, Lourdes
  • Fondevila, Manuel
  • Belanche, Alejandro
Young dairy ruminants often have limited rumen fermentative capacity, which can impair adaptation to solid diet during weaning. This study evaluated the effects of ruminant colostrum supplementation to enhance in vitro rumen fermentation at weaning. A batch culture system using rumen inoculum from artificially reared lambs was incubated with ovine, bovine, or reconstituted bovine colostrum at 4 and 20 mL/L. Sequential colostrum fractionation was used to identify the main functional components. Whole colostrum supplementation at high doses reduced ruminal pH (p < 0.001) and increased gas production (+18%), ammonia-N (+41%) and butyrate proportion (+10%) across colostrum sources, indicating enhanced microbial fermentation. Responses were dose-dependent and consistent across colostrum sources. Lipid removal had minimal effects, whereas depletion of high-molecular-weight molecules, mostly IgG, markedly reduced gas production and protein degradation. Removal of medium-size proteins such as lactoferrin produced minor changes. Residual activity in low-molecular-weight fractions was retained likely associated with the presence of fermentable substrates and bioactive compounds. These findings indicate that colostrum may exhibit both nutritional and modulatory effects on in vitro rumen fermentation, with IgG identified as a key component. These findings support the preservation of IgG in colostrum-derived products to enhance rumen fermentation, although further in vivo validation is required to evaluate the effects in weaned ruminants.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Soil luminance and thermography support the estimation of whole-field solid-set sprinkler irrigation uniformity

  • Zapata, N.
  • Neji, A.
  • Latorre, B.
  • Serreta, A.
  • Medina, E. T.
  • Paniagua, P.
  • Playán, E.
Application efficiency and distribution uniformity are the key indicators of irrigation performance. Field evaluation of irrigation uniformity with rain gauges is the standard practice, but it is time-consuming and limited in spatial coverage. Remote soil observation methodologies can be an interesting alternative or a complement to characterize irrigation variability. The aim of this research is to develop novel approaches to evaluate the spatial variability of water application in solid-set sprinkler irrigation across an entire field (with bare soil) using a combination of ground-sensors and Unmanned Aerial Vehicles (UAV) based remote sensing techniques. Experimental field trials were conducted to measure the variability of applied irrigation depth using standard methods (rain gauges), local soil temperature sensors and UAV-acquired thermal and visible (RGB) imagery. Additionally, a field trial on a proxy of a commercial field was performed to test the methodology. Local soil temperature measurements at a depth of 5 cm showed strong correlation with irrigation depth measured with rain gauges, particularly in sprinkler arrangements leading to low uniformity (average R2 = 0.55 and RMSE = 1.21 mm). Thermal and visible UAV images effectively explained irrigation depth and variability, with thermal images achieving higher determination coefficients (average R2 = 0.83 and RMSE = 0.7 mm) than visible images (average R2 = 0.78 and RMSE = 0.9 mm). The best performance indicators were observed 3.5–5 h post-irrigation for soil luminance derived from RGB imagery and 5–7 h post-irrigation for thermal imagery. Remote soil temperature also performed better than local measured soil temperature. Linear regression models explaining irrigation depth variability based on soil temperature or luminance were influenced by environmental factors. To avoid this dependency, we propose to develop relational models using only 15 rain gauge measurements, which are used to train the UAV images. This method was validated through experimental trials and applied to estimate whole-field irrigation uniformity.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Current trends in solid state ionics: Solid oxide cells a proceedings-perspective paper of the E-MRS 2025 spring meeting (symposium K: “Solid state ionics: Functional materials and devices for electrochemical energy conversion and storage applications”)

  • Burriel, Mónica
  • Tarancon, Albert
  • Laguna-Bercero, Miguel A.
With this series of proceedings-perspective articles, the journal Solid State Ionics introduces a novel format of progress reports from the research community that aims to bridge the gap between traditional conference proceedings and perspective articles. In addition, it has become apparent in recent years that traditional conference proceedings papers (presumably also favoured by a significant acceleration in scientific publishing) no longer meet the response that was the case in earlier times. This new paper format is an attempt to meet the needs of researchers in a modern publication environment to report the latest developments at the forefront of science (as they are usually discussed at conferences), which are thus brought into a citable form as soon as possible. We thus believe that this innovative format offers several advantages: It accelerates the dissemination of cutting-edge research, provides strategic guidance on promising research directions, increases the visibility of key conference papers, delivers efficiently curated content to readers, and provides a good balance between timely coverage and scientific depth. The E-MRS 2025 Spring Meeting Symposium K on “Solid state ionics: functional materials and devices for electrochemical energy conversion and storage applications” serves as the first conference where the Solid State Ionics community is exploring this innovative publication approach. Rather than providing exhaustive coverage of all presentations, this new format of proceedings-perspective papers highlights key developments and emerging research directions within the field of solid state ionics as identified by leading contributors in each subfield. Each paper focuses on one of the following four central topics. Defect Engineering & Surface Chemistry. Solid Oxide Cells. Protonics & Reactors. Batteries.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Evaluation of transfer learning by means of fuzzy logic for hand gesture recognition

  • Ojeda-Castelo, Juan Jesus
  • Piedra-Fernandez, Jose A.
  • Rodriguez-Gracia, Diego
  • Ayala, Rosa
Hand gesture recognition (HGR) is increasingly adopted in real-world applications, yet selecting the most suitable model–hyperparameter configuration remains a time-consuming and opaque process. This work introduces a systematic evaluation framework for static HGR that combines transfer learning (TL) with a fuzzy logic expert system to provide a reproducible and transparent ranking of candidate models. We benchmark eight widely used CNN backbones across 64 fine-tuned configurations, analyzing their performance in terms of accuracy, recall, and F1-score, while explicitly documenting the fuzzy inference rules used to integrate these metrics. Experiments on 3-class and 5-class subsets of the Tiny Hand Gesture dataset consistently highlight the robustness of classical architectures such as VGG16 and ResNet50, with the best configuration achieving an F1-score of 0.995. Beyond accuracy, we extend the analysis to computational efficiency, showing that deeper or next-generation networks often incur higher training time and memory costs without yielding performance gains. Finally, we report an exploratory hybrid quantum–classical experiment based on ResNet50 with a variational quantum layer, which improved test accuracy from 0.876 to 0.94, at the expense of extremely high training costs. Overall, our contribution is threefold: (i) a reproducible TL evaluation pipeline with fuzzy ranking, (ii) an evidence-based comparison of classical versus modern CNN architectures in static HGR, and (iii) an initial exploration of quantum machine learning integration for gesture classification.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Renewable Platform Chemicals from Biomass: Pathways, Technologies and Challenges

  • Moreira, Rui
  • Atienza-Martínez, Maria
  • Gil-Lalaguna, Noemí
  • Bimbela, Fernando
  • Cornejo, Alfonso
  • Serra, Arménio
  • Coelho, Jorge
  • Gandía, Luis M.
  • Arauzo, Jesús
  • Sánchez, José Luis
The production of renewable chemicals and plastics has been extensively investigated in recent decades, with the purpose of reducing the global dependence on fossil resources. In this review, the main routes to produce chemicals from biomass are reviewed and a critical discussion on the prospects and techno-economic viability of these technologies is presented. As these topics are often considered as independent from each other, the aim of this work is to provide an unified and interdisciplinary perspective of main possible production routes and their development status for experts and non-experts. The main processes of biomass concentration were reviewed and two main approaches for obtaining renewable chemicals were considered: (i) the production of compounds chemically identical to petroleum derivatives, and (ii) the production of conventional and new oxygenated chemicals. The literature shows that there are sustainable technological alternatives to the substitution of many petroleum derived chemicals, but the complexity of the production processes should not be simplistically evaluated. Solutions and technologies must be carefully evaluated, both from the point of view of their technoeconomic viability and their sustainability.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Competitive solid oxide cells using YSr2Cu2FeO7+δ based oxygen electrodes prepared by combustion synthesis

  • Zueco-Vincelle, Juan
  • Marín-Gamero, Rafael
  • de la Torre-Gamarra, Carmen
  • Orera, Alodia
  • García-Alvarado, Flaviano
  • García-Martín, Susana
  • Laguna-Bercero, Miguel A.
In this paper we present the electrochemical performance of YSr2Cu2FeO7+δ (YSCF). YSCF was prepared by the combustion method and showed YBaCuO-type structure. Symmetrical cells with YSCF-Ce0.9Gd0.1O2-δ (CGO) electrodes showed a polarization resistance of 0.3 Ω cm2 at 600 °C. Then, YSCF was incorporated in fuel electrode supported solid oxide cells (SOCs). SOCs were composed by the Ni-8% mol stabilized ZrO2 (YSZ) cermet as fuel electrode, YSZ as electrolyte, CGO as barrier layer and the composite YSCF-CGO as oxygen electrode. A SOC with (La0.6Sr0.4)0.95Fe0.8Co0.2O3−δ (LSCF)-CGO oxygen electrode was also fabricated as reference cell. At 800 °C under 50:50% H2O:H2 in the fuel electrode and air in the oxygen electrode, YSCF-based cell reached a maximum power output of 0.74 W cm−2 at 0.5 V in SOFC mode and −1.1 A cm−2 at thermoneutral voltage (1.3 V) in SOEC mode. In the same conditions, EIS measurements revealed a polarization resistance of 0.17 Ω cm2.