Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

UiO-66 MOF-Derived Ru@ZrO2 catalysts for photo-thermal CO2 hydrogenation

  • Almazán, Fernando
  • Lafuente, Marta
  • Echarte, Amaya
  • Imizcoz, Mikel
  • Pellejero, Ismael
  • Gandía, Luis M.
This article belongs to the Special Issue Heterogeneous Catalysis — A Themed Issue in Honor of Prof. Dr. Avelino Corma., The use of metal–organic frameworks (MOFs) as templates or precursors in the manufacture of heterogeneous catalysts is highly attractive due to the transfer of MOFs’ inherent porosity and homogeneous metallic distribution to the derived structure. Herein, we report on the preparation of MOF-derived Ru@ZrO2 catalysts by controlled thermal treatment of zirconium-based MOF UiO-66 with ruthenium moieties. Ru3+ (3 or 10 mol%) precursor was added to UiO-66 synthesis and, subsequently, the as-synthesized hybrid structure was calcined in flowing air at different temperatures (400–600 °C) to obtain ZrO2-derived oxides doped with highly dispersed Ru metallic clusters. The materials were tested for the catalytic photo-thermal conversion of CO2 to CH4. Methanation experiments were conducted in a continuous flow (feed flow rate of 5 sccm and 1:4 CO2 to H2 molar ratio) reactor at temperatures from 80 to 300 °C. Ru0.10@ZrO2 catalyst calcined at 600 °C was able to hydrogenate CO2 to CH4 with production rates up to 65 mmolCH4·gcat.–1·h–1, CH4 yield of 80% and nearly 100% selectivity at 300 °C. The effect of the illumination was investigated with this catalyst using a high-power visible LED. A CO2 conversion enhancement from 18% to 38% was measured when 24 sun of visible LED radiation was applied, mainly due to the increase in the temperature as a result of the efficient absorption of the radiation received. MOF-derived Ru@ZrO2 catalysts have resulted to be noticeably active materials for the photo-thermal hydrogenation of CO2 for the purpose of the production of carbon-neutral methane. A remarkable effect of the ZrO2 crystalline phase on the CH4 selectivity has been found, with monoclinic zirconia being much more selective to CH4 than its cubic allotrope., Financial support was obtained from Spanish Agencia Estatal de Investigación and Spanish Ministerio de Ciencia e Innovación MCIN/AEI/10.13039/501100011033/ and FEDER “Una manera de hacer Europa” (grants PID2019-106687RJ-I00/AEI/ 10.13039/501100011033 and PID2021-127265OB-C21), as well as from Plan de Recuperación, Transformación y Resiliencia and NextGenerationEU (grants PLEC2022-009221 and TED2021-130846B-100), which is gratefully acknowledged. M.L. and M.I. thank Spanish Ministerio de Universidades and Unión Europea-NextGenerationEU for the postdoctoral ¨Margarita Salas¨ and FPU 18/01877 grants, respectively. A.E. thanks Universidad Pública de Navarra for the predoctoral fellowship. L.M.G. thanks the Banco de Santander and Universidad Pública de Navarra for their financial support under “Programa de Intensificación de la Investigación 2018” initiative., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

UiO-66 MOF-Derived Ru@ZrO2 Catalysts for Photo-Thermal CO2 Hydrogenation

  • Almazán, Fernando
  • Lafuente, Marta
  • Echarte, Amaya
  • Imizcoz, Mikel
  • Pellejero, Ismael
  • Gandía, Luis M.
The use of metal–organic frameworks (MOFs) as templates or precursors in the manufacture of heterogeneous catalysts is highly attractive due to the transfer of MOFs’ inherent porosity and homogeneous metallic distribution to the derived structure. Herein, we report on the preparation of MOF-derived Ru@ZrO2 catalysts by controlled thermal treatment of zirconium-based MOF UiO-66 with ruthenium moieties. Ru3+ (3 or 10 mol%) precursor was added to UiO-66 synthesis and, subsequently, the as-synthesized hybrid structure was calcined in flowing air at different temperatures (400–600 °C) to obtain ZrO2-derived oxides doped with highly dispersed Ru metallic clusters. The materials were tested for the catalytic photo-thermal conversion of CO2 to CH4. Methanation experiments were conducted in a continuous flow (feed flow rate of 5 sccm and 1:4 CO2 to H2 molar ratio) reactor at temperatures from 80 to 300 °C. Ru0.10@ZrO2 catalyst calcined at 600 °C was able to hydrogenate CO2 to CH4 with production rates up to 65 mmolCH4·gcat.–1·h–1, CH4 yield of 80% and nearly 100% selectivity at 300 °C. The effect of the illumination was investigated with this catalyst using a high-power visible LED. A CO2 conversion enhancement from 18% to 38% was measured when 24 sun of visible LED radiation was applied, mainly due to the increase in the temperature as a result of the efficient absorption of the radiation received. MOF-derived Ru@ZrO2 catalysts have resulted to be noticeably active materials for the photo-thermal hydrogenation of CO2 for the purpose of the production of carbon-neutral methane. A remarkable effect of the ZrO2 crystalline phase on the CH4 selectivity has been found, with monoclinic zirconia being much more selective to CH4 than its cubic allotrope.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A prospective review on bioplastics and biopolymers

  • Moreira, Rui
  • Atienza-Martínez, Maria
  • Gil-Lalaguna, Noemí
  • Serra, Arménio
  • Cornejo, Alfonso
  • Bimbela, Fernando
  • Coelho, Jorge
  • Gandía, Luis M.
  • Arauzo, Jesus
  • Sánchez, José Luis
The production of bioplastics has been extensively investigated in recent decades, with the purpose of reducing the global dependence on fossil resources. In this review, the main routes to produce bioplastics and a critical discussion of these technologies are presented. The synthesis routes to produce biodegradable and non-biodegradable bioplastics are discussed. Additionally, approaches to improve the environmental footprint of some conventional plastics that have no immediate solutions of substitution are also addressed. A comparison of the main properties of the bioplastics considered and a general perspective of the bioplastics market are also provided. Because these themes have often been reviewed separately, this article aims to provide a unified general perspective of bioplastics in the context of a biobased economy, as well as pointing out some of the hurdles in such way.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Renewable Platform Chemicals from Biomass: Pathways, Technologies and Challenges

  • Moreira, Rui
  • Atienza-Martínez, Maria
  • Gil-Lalaguna, Noemí
  • Bimbela, Fernando
  • Cornejo, Alfonso
  • Serra, Arménio
  • Coelho, Jorge
  • Gandía, Luis M.
  • Arauzo, Jesús
  • Sánchez, José Luis
The production of renewable chemicals and plastics has been extensively investigated in recent decades, with the purpose of reducing the global dependence on fossil resources. In this review, the main routes to produce chemicals from biomass are reviewed and a critical discussion on the prospects and techno-economic viability of these technologies is presented. As these topics are often considered as independent from each other, the aim of this work is to provide an unified and interdisciplinary perspective of main possible production routes and their development status for experts and non-experts. The main processes of biomass concentration were reviewed and two main approaches for obtaining renewable chemicals were considered: (i) the production of compounds chemically identical to petroleum derivatives, and (ii) the production of conventional and new oxygenated chemicals. The literature shows that there are sustainable technological alternatives to the substitution of many petroleum derived chemicals, but the complexity of the production processes should not be simplistically evaluated. Solutions and technologies must be carefully evaluated, both from the point of view of their technoeconomic viability and their sustainability.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

CO2 methanation over nickel catalysts: support effects investigated through specific activity and operando IR spectroscopy measurement

  • González Rangulan, Vigni Virginia
  • Reyero Zaragoza, Inés
  • Bimbela Serrano, Fernando
  • Romero Sarria, Francisca
  • Daturi, Marco
  • Gandía Pascual, Luis
Renewed interest in CO2 methanation is due to its role within the framework of the Power-to-Methane processes. While the use of nickel-based catalysts for CO2 methanation is well stablished, the support is being subjected to thorough research due to its complex effects. The objective of this work was the study of the influence of the support with a series of catalysts supported on alumina, ceria, ceria–zirconia, and titania. Catalysts’ performance has been kinetically and spectroscopically evaluated over a wide range of temperatures (150–500 °C). The main results have shown remarkable differences among the catalysts as concerns Ni dispersion, metallic precursor reducibility, basic properties, and catalytic activity. Operando infrared spectroscopy measurements have evidenced the presence of almost the same type of adsorbed species during the course of the reaction, but with different relative intensities. The results indicate that using as support of Ni a reducible metal oxide that is capable of developing the basicity associated with medium-strength basic sites and a suitable balance between metallic sites and centers linked to the support leads to high CO2 methanation activity. In addition, the results obtained by operando FTIR spectroscopy suggest that CO2 methanation follows the formate pathway over the catalysts under consideration., Financial support from Spanish Ministerio de Ciencia e Innovación and Agencia Estatal de Investigación MCIN/AEI/10.13039/501100011033/ and FEDER “Una manera de hacer Europa” (grant PID2021-127265OB-C21), as well as from Plan de Recuperación, Transformación y Resiliencia and NextGenerationEU (grants PLEC2022-009221 and TED2021-130846B-100) is gratefully acknowledged. Financial support from Universidad Pública de Navarra is also thanked for the PhD grant awarded to V.V. González-Rangulan. V.V. González-Rangulan also acknowledges the CNRS for the financial support, the guidance, and assistance provided during the 3-month research sojourn in ENSICAEN. L.M. Gandía also thanks Banco de Santander and Universidad Pública de Navarra for their financial support under “Programa de Intensificación de la Investigación 2018” initiative.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Gaseous fueling of an adapted commercial automotive spark-ignition engine: simplified thermodynamic modeling and experimental study running on hydrogen, methane, carbon monoxide and their mixtures

  • Urroz Unzueta, José Carlos
  • Diéguez Elizondo, Pedro
  • Arzamendi Manterola, Gurutze
  • Arana Burgui, Miguel
  • Gandía Pascual, Luis
In the present work, methane, carbon monoxide, hydrogen and the binary mixtures 20 % CH4–80 % H2, 80 % CH4–20 % H2, 25 % CO–75 % H2 (by volume) were considered as fuels of a naturally aspirated port-fuel injection four-cylinder Volkswagen 1.4 L spark-ignition (SI) engine. The interest in these fuels lies in the fact that they can be obtained from renewable resources such as the fermentation or gasification of residual biomasses as well as the electrolysis of water with electricity of renewable origin in the case of hydrogen. In addition, they can be used upon relatively easy modifications of the engines, including the retrofitting of existing internal combustion engines. It has been found that the engine gives similar performance regardless the gaseous fuel nature if the air–fuel equivalence ratio (λ) is the same. Maximum brake torque and mean effective pressure values within 45–89 N⋅m and 4.0–8.0 bar, respectively, have been obtained at values of λ between 1 and 2 at full load, engine speed of 2000 rpm and optimum spark-advance. In contrast, the nature of the gaseous fuel had great influence upon the range of λ values at which a fuel (either pure or blend) could be used. Methane and methane-rich mixtures with hydrogen or carbon monoxide allowed operating the engine at close to stoichiometric conditions (i.e. 1 < λ < 1.5) yielding the highest brake torque and mean effective pressure values. On the contrary, hydrogen and hydrogen-rich mixtures with methane or carbon monoxide could be employed only in the very fuel-lean region (i.e. 1.5 < λ < 2). The behavior of carbon monoxide was intermediate between that of methane and hydrogen. The present study extends and complements previous works in which the aforementioned fuels were compared only under stoichiometric conditions in air (λ = 1). In addition, a simple zero-dimensional thermodynamic combustion model has been developed that allows describing qualitatively the trends set by the several fuels. Although the model is useful to understand the influence of the fuels properties on the engine performance, its predictive capability is limited by the simplifications made., Financial support from Spanish Ministerio de Ciencia e Innovación and Agencia Estatal de Investigación MCIN/AEI/10.13039/501100011033/ and FEDER “Una manera de hacer Europa” (grant PID2021-127265OB-C21), as well as from Plan de Recuperación, Transformación y Resiliencia and NextGenerationEU (grants PLEC2022-009221 and TED2021-130846B-100) is gratefully acknowledged. L.M. Gandía also thanks Banco de Santander and Universidad Pública de Navarra for their financial support under “Programa de Intensificación de la Investigación 2018” initiative. Authors also acknowledge Open Access Funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

How bimetallic CoMo carbides and nitrides improve CO oxidation

  • Villasana, Yanet
  • García Macedo, Jorge A.
  • Navarro Puyuelo, Andrea
  • Reyero Zaragoza, Inés
  • Lara, Hugo
  • Bimbela Serrano, Fernando
  • Gandía Pascual, Luis
  • Brito, Joaquin L.
  • Méndez, Franklin J.
CO elimination is an important step for the proper management of gaseous effluents from various processes, thus avoiding adverse impacts on the environment and human health. In this study, different bimetallic Al2O3-supported CoMo catalysts have been developed, characterized, and tested in the CO oxidation reaction, based on their respective oxides, carbides, and nitrides phases. The parent CoMo-oxide catalyst (CoMo) was prepared by impregnation and then transformed to its carburized (CoMoC) and nitrided (CoMoN) forms using temperatureprogrammed reaction methods under controlled atmospheres of CH4/H2 and NH3, respectively. The catalytic results demonstrate that the CoMoC catalyst exhibits higher activity compared to its CoMoN counterpart, and both are more active than the parent CoMo catalyst. Furthermore, the reduction temperature and space velocity were key process factors, which notably influenced activity and kinetic parameters, while the increase of reduction time does not seem to improve catalytic behavior. These results were associated with a better metal dispersion, and relatively higher reduction grade and metallic surface area on the carbides and nitrides, opening the possibility that new adsorption sites may be created. The catalytic results compare favorably with other nonnoble metal catalysts, such as Cr-, Cu-, Fe-, and Ni-based samples, and highlight the potential of using carbides and nitrides as alternative formulations to enhance the performance of CO oxidation., All authors would like to express our sincere appreciation to the Agencia Española de Cooperación Internacional para el Desarrollo (AECID) through the Ikiam-UE-AECID 2018/SPE/0000400194 agreement for funding the research. F.J. Méndez also thanks SIP-IPN for partially supporting the research through the SIP-IPN-20230056 project, while J.A. Garcia-Macedo and H.A. Lara-Garcia thank DGAPA-UNAM through the PAPIIT-IN112622 and PAPIIT-IA107023 projects, respectively. L.M. Gandía, F. Bimbela and the rest of UPNA co-authors would also like to thank the Spanish Agencia Estatal de Investigación (AEI) and Ministerio de Ciencia e Innovación (MICINN), as well as the European Union’s NextGenerationEU Funds and the European Regional Development Fund (ERDF/FEDER), for granting additional financial support (Project Refs. PID2021-127265OB-C21 and TED2021-130846B-I00) and for the funding provided to hire A. Navarro-Puyuelo as postdoctoral researcher (Project Ref. PLEC2022-009221). M. Boujnah and J. Muñiz also would like to acknowledge the Supercomputing Department (UNAM) for the computing resources under Projects Ref. LANCAD-UNAM-DGTIC-425 project. Likewise, M. Boujnah (CVU number 1018873) wants to acknowledge CONAHCYT-México for his postdoctoral fellowship.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

The 3D-printing fabrication of multichannel silicone microreactors for catalytic applications

  • Ibáñez de Garayo Quilchano, Alejandro
  • Imizcoz Aramburu, Mikel
  • Maisterra Udi, Maitane
  • Almazán, Fernando
  • Sanz Carrillo, Diego
  • Bimbela Serrano, Fernando
  • Cornejo Ibergallartu, Alfonso
  • Pellejero, Ismael
  • Gandía Pascual, Luis
Microstructured reactors (MSRs) are especially indicated for highly demanding heterogeneous catalysis due to the small channel dimensions that minimize diffusional limitations and enhance mass and heat transport between the fluid and the catalyst. Herein, we present the fabrication protocol of the fused filament 3D printing of silicone monolithic microreactors based on a multichannel design. Microchannels of 200 to 800 µm in width and up to 20 mm in length were developed following the scaffold-removal procedure using acrylonitrile butadiene styrene (ABS) as the material for the 3D-printed scaffold fabrication, polydimethylsiloxane (PDMS) as the building material, and acetone as the ABS removing agent. The main printing parameters such as temperature and printing velocity were optimized in order to minimize the bridging effect and filament collapsing and intercrossing. Heterogeneous catalysts were incorporated into the microchannel walls during fabrication, thus avoiding further post-processing steps. The nanoparticulated catalyst was deposited on ABS scaffolds through dip coating and transferred to the microchannel walls during the PDMS pouring step and subsequent scaffold removal. Two different designs of the silicone monolithic microreactors were tested for four catalytic applications, namely liquid-phase 2-nitrophenol photohydrogenation and methylene blue photodegradation in aqueous media, lignin depolymerization in ethanol, and gas-phase CO2 hydrogenation, in order to investigate the microreactor performance under different reaction conditions (temperature and solvent) and establish the possible range of applications., Financial support was received from Spanish Agencia Estatal de Investigación and Spanish Ministerio de Ciencia e Innovación MCIN/AEI/10.13039/501100011033/ and FEDER “Una manera de hacer Europa” (grants PID2019-106687RJ-I00/AEI/10.13039/501100011033 and PID2021-127265OB-C21) as well as from Plan de Recuperación, Transformación y Resiliencia and NextGenerationEU (grants PLEC2022-009221 and TED2021-130846B-100), and Gobierno de Navarra grant PC091-092 FOREST2+ which are gratefully acknowledged. The Spanish Ministerio de Universidades fellowship FPU 18/01877 was granted to M.I. The Universidad Pública de Navarra predoctoral fellowship was granted to M.M. L.M. Gandía thanks Banco de Santander and Universidad Pública de Navarra for their financial support under the “Programa de Intensificación de la Investigación 2018” initiative.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

UiO-66 MOF-Derived Ru@ZrO2 catalysts for photo-thermal CO2 hydrogenation

  • Almazán, Fernando
  • Lafuente Adiego, Marta
  • Echarte Villeras, Amaya
  • Imizcoz Aramburu, Mikel
  • Pellejero, Ismael
  • Gandía Pascual, Luis
The use of metal–organic frameworks (MOFs) as templates or precursors in the manufacture of heterogeneous catalysts is highly attractive due to the transfer of MOFs’ inherent porosity and homogeneous metallic distribution to the derived structure. Herein, we report on the preparation of MOF-derived Ru@ZrO2 catalysts by controlled thermal treatment of zirconium-based MOF UiO66 with ruthenium moieties. Ru3+ (3 or 10 mol%) precursor was added to UiO-66 synthesis and, subsequently, the as-synthesized hybrid structure was calcined in flowing air at different temperatures (400–600 ◦C) to obtain ZrO2 -derived oxides doped with highly dispersed Ru metallic clusters. The materials were tested for the catalytic photo-thermal conversion of CO2 to CH4 . Methanation experiments were conducted in a continuous flow (feed flow rate of 5 sccm and 1:4 CO2 to H2 molar ratio) reactor at temperatures from 80 to 300 ◦C. Ru0.10@ZrO2 catalyst calcined at 600 ◦C was able to hydrogenate CO2 to CH4 with production rates up to 65 mmolCH4·gcat. –1 ·h –1, CH4 yield of 80% and nearly 100% selectivity at 300 ◦C. The effect of the illumination was investigated with this catalyst using a high-power visible LED. A CO2 conversion enhancement from 18% to 38% was measured when 24 sun of visible LED radiation was applied, mainly due to the increase in the temperature as a result of the efficient absorption of the radiation received. MOF-derived Ru@ZrO2 catalysts have resulted to be noticeably active materials for the photo-thermal hydrogenation of CO2 for the purpose of the production of carbon-neutral methane. A remarkable effect of the ZrO2 crystalline phase on the CH4 selectivity has been found, with monoclinic zirconia being much more selective to CH4 than its cubic allotrope., Financial support was obtained from Spanish Agencia Estatal de Investigación and Spanish Ministerio de Ciencia e Innovación MCIN/AEI/10.13039/501100011033/ and FEDER “Una manera de hacer Europa” (grants PID2019-106687RJ-I00/AEI/ 10.13039/501100011033 and PID2021-127265OB-C21), as well as from Plan de Recuperación, Transformación y Resiliencia and NextGenerationEU (grants PLEC2022-009221 and TED2021-130846B-100), which is gratefully acknowledged. M.L. and M.I. thank Spanish Ministerio de Universidades and Unión Europea-NextGenerationEU for the postdoctoral ¨Margarita Salas¨ and FPU 18/01877 grants, respectively. A.E. thanks Universidad Pública de Navarra for the predoctoral fellowship. L.M.G. thanks the Banco de Santander and Universidad Pública de Navarra for their financial support under “Programa de Intensificación de la Investigación 2018” initiative.