Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Probing high oxygen activity in YSZ electrolyte

  • Robles-Fernández, A.
  • Orera, A.
  • Peña, J. I.
  • Merino, R. I.
The redox behavior of terbium and praseodymium doped yttria-stabilized zirconia (YSZ) is studied. The aim is to identify spectroscopic probes and a suitable experimental procedure to monitor the oxygen activity in YSZ electrolytes in solid oxide cells with spatial resolution and at operation conditions (e.g. at high temperatures). Sintered ceramics and crystals with 0.3 to 10 at% content of Pr or Tb ions in YSZ were prepared. Upon equilibration in atmospheres from 10-20to 100 bar PO2around 800 °C, the majority of these rare earth ions are in the 3 + oxidation state. At oxygen pressures above 0.001 bar, the small proportion of Tb4+and Pr4+formed give rise to intense optical absorption around 300 500 nm and to decreased reflectance. From the reflectance measurements it is shown that the Tb4+concentration increases as PO21/4, as correspond to the trapping of the holes generated upon the oxygen incorporation as Tb4+. This competitive absorption causes a decrease of the Tb3+luminescence. A quantitative relationship of the Tb3+luminescence intensity with PO2at 800 °C has been found, which is compatible with the trapping model. The spatial resolution of the experimental procedure could be very roughly estimated of the order of 100 µm.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Laser processing of ceramic materials for electrochemical and high temperature energy applications

  • Merino, R.I.
  • Laguna-Bercero, M.A.
  • Lahoz, R.
  • Larrea, Á.
  • Oliete, P.B.
  • Orera, A.
  • Peña, J.I.
  • Sanjuán, M.L.
  • Sola, D.
The laser is a powerful tool for materials processing, incorporated already in many industrial processes and laboratory procedures. In this work, we are concerned with laser processing applied to research and development of ceramics for electrochemical cells and other high temperature oxide ceramics for energy applications. Solidification of single crystals or composites of relevant oxides can be performed by the laser assisted floating zone method, providing samples for structural, mechanical or functional fundamental research, as well as knowledge about its manufacture by melt processes. Selective laser melting of these ceramic oxides is a very promising technology, at the research level. Successful examples of surface laser melting of oxide eutectic composites are presented. The technologies of subtractive laser processing of ceramics (cutting, drilling, structuring, cleaning, etc.) are more developed, and the research is directed towards the optimization of mechanisms, increase of resolution and efficiency and the investigation of the effects of the laser treatment on the functional performance. Different laser processes of SOC (solid oxide cell) components are shown to decrease the ohmic, concentration and activation losses. The manuscript describes the state-of-the art of the technologies as applied to oxide and composite materials present in solid oxide electrochemical devices (SOFC, SOEC, and batteries) and selective emitters for thermophotovoltaics, with emphasis on the last achievements by the authors team. El láser es una potente herramienta para el procesamiento de materiales, incorporada ya en muchos procesos industriales y procedimientos de laboratorio. En este trabajo nos ocupamos del procesamiento láser aplicado a la investigación y desarrollo de cerámicas para celdas electroquímicas y otras cerámicas de óxido de alta temperatura para aplicaciones energéticas. La solidificación de monocristales o composites de óxidos relevantes se puede realizar mediante el método de zona flotante asistida por láser, proporcionando muestras para investigación básica estructural, de propiedades mecánicas o funcionales, así como conocimiento sobre su fabricación mediante procesos de fusión. La fusión selectiva por láser de estos óxidos cerámicos es una tecnología muy prometedora, cuyo desarrollo es todavía incipiente. Se presentan ejemplos exitosos de fusión por láser de superficie de compuestos eutécticos de óxidos. Las tecnologías sustractivas de procesamiento de cerámicas con láser (corte, taladrado, estructuración, limpieza, etc.) están más desarrolladas, y la investigación se dirige hacia la optimización de procedimientos, aumento de resolución y eficiencia y la investigación de los efectos del tratamiento láser sobre el rendimiento funcional. Diferentes procesos láser de los componentes de celda de óxido sólido disminuyen las pérdidas óhmicas, de concentración y de activación. El manuscrito describe el estado actual de las tecnologías aplicadas a óxidos y materiales compuestos presentes en dispositivos electroquímicos de óxidos sólidos (SOFC, SOEC y baterías) y emisores selectivos para aplicaciones termofotovoltaicas, con énfasis en los últimos logros del equipo.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Eutectic ceramics of the CeO2 – ZrO2 – MgO system produced by laser-assisted directional solidification

  • Orera, Alodia
  • Oliete, Patricia B.
  • Merino, Rosa I.
  • Sanjuán, María Luisa
Oxide eutectics have great potentiality as structural or functional materials, owing to the outstanding properties derived from the eutectic microstructure. Among them, the eutectic of the ZrO2 – MgO system is particularly noteworthy because of the unusual combination of thermomechanical, optical and electrical properties. In a recent application, Zr1-δMgδO2-δ – MgO eutectic oxides have been used to produce porous supports for molten-carbonate based CO2 separation membranes. Here we explore composite ceramic oxides of the CexZr1-xO2 – MgO (x ​≤ ​0.5) system with eutectic microstructure, with the motivation that incorporating cerium may enhance the CO2 permeation properties. Eutectic composites with different cerium content are produced by a laser-assisted directional solidification technique at variable solidification rate, v. In all cases the composite bicrystal consists of two phases, MgO and a fluorite-like (CexZr1-x)1-yMgyO2-y phase. A purely fibrilar microstructure is found for x ​≥ ​0.3 ​at v ​= ​25 ​mm/h, with MgO fibres embedded within the fluorite-like matrix. The MgO mol% in the eutectic composites decreases from ∼53% for x ​= ​0 to ∼48% for x ​= ​0.5. X-ray and Raman results evidence long-range ordering in a quasi-tetragonal monoclinic symmetry for x ​= ​0.5. Impedance spectroscopy results are consistent with a change from ionic to mainly electronic conductivity when the atmosphere is changed from air or Ar to 5%H2–Ar.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Laser-Induced Surface Modification on Wollastonite-Tricalcium Phosphate and Magnesium Oxide-Magnesium Stabilized Zirconia Eutectics for Bone Restoring Applications

  • Wang, Shunheng
  • Sola, Daniel
  • Peña, Jose I.
An adaptation of the laser floating zone technique is used to modify the surface properties of ceramics with interest for biomedical applications. This new method is based upon the surface remelting of ceramic rods by using laser radiation, and its versatility is demonstrated in the surface structuring of two different eutectic composites with potential application as bone substitutes. Firstly, directionally eutectic rods of wollastonite (W)–tricalcium phosphate (TCP) and magnesium oxide (MgO)–magnesium stabilized zirconia (MgSZ) were grown by the laser floating zone technique. In the case of W-TCP eutectics, materials with crystalline, glass–ceramic, or vitreous microstructure could be obtained as the growth rate was increased. In the other case, a material made up of magnesium oxide and magnesium stabilized zirconia phases arranged in fibrillar or lamellar geometry was obtained. At higher solidification rates, the rupture of the growth front gave rise to the organization of the phases in the form of colonies or cells. The laser zone remelting technique was used to remove defects and to refine the microstructure of the directionally solidified eutectic surfaces as well as to cover MgO–MgSZ rods with W–TCP glass in the eutectic composition. The study provides a promising technique that can tailor the surface properties and functionality of bone repair materials. The products’ properties and challenges in preparation procedures are discussed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Lanthanide nickelates for their application on Solid Oxide Cells

  • Morales-Zapata, M.A.
  • Larrea, A.
  • Laguna-Bercero, M.A.
High-temperature technologies like solid oxide cells (SOC) have been employed to provide power-to-fuel and vice versa for energy conversion and storage. These technologies are a work in progress due to durability and compatibility issues between components at high temperatures. For this reason, the pursuit of optimal physical, mechanical, and chemical properties of SOC materials at lower temperatures has become more diligent. Finding suitable air electrodes has become one of the more notable obstacles to complete implementation in the industry. One of the most recent alternatives is the use of lanthanide nickelates with the Ruddlesden-Popper (RP), Lnn+1NinO3n±1 (Ln = La, Nd or Pr), and perovskite, LnNiO3-δ, structures. These materials present fast ionic and electronic transport, as well as flexible oxygen stoichiometry that makes them compelling for this purpose. As part of an ongoing study on alternative air electrode advanced materials, this review is focused on documenting the relevant findings of RP nickelates over the years, especially focusing on the current status in research and development while comparing the electrochemical performance of nickelate air electrodes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ceramics with eutectic microstructure in the ZrO2–PrOx system

  • Grima, Lorena
  • Peña, José Ignacio
  • Sanjuán, María Luisa
Praseodymium oxides present redox properties analogous to those of Ce‐based systems and have been proposed for catalytic applications in combination with CeO2, ZrO2, or both. However, uncertainties remain concerning the nature and redox behavior of Pr‐rich mixtures, especially with ZrO2. Here we study the eutectic composites of the ZrO2–PrOx system, focusing on the sensitivity of their microstructure, phase symmetry, and composition to variations of the processing atmosphere from oxidizing to reducing. Mixed oxides have been produced by a laser‐assisted directional solidification technique in O2, air, N2, or 5%H2(Ar) environment, and the resulting materials have been analyzed by scanning electron microscopy/energy‐dispersive X‐ray spectroscopy, X‐ray diffraction, Raman spectroscopy, and magnetic susceptibility. In air, N2, or 5%H2(Ar) atmosphere, a lamellar, eutectic‐like microstructure forms, the major phase being the one with less Pr content. Both the Pr concentration in each phase as the PrOx molar percentage of the eutectic composites decrease as the atmosphere becomes more reducing. Both eutectic phases are fluorite‐like when processing in air, whereas in N2 or 5%H2(Ar), the phase with high Pr content is of the A‐R2O3 type, and the phase with low Pr content can be described as a fluorite phase containing C‐R2O3‐like short‐range‐ordered regions. The results obtained for samples processed in O2 suggest that for high enough pO2 no eutectic forms, in analogy with the ZrO2–CeO2 system. The evolution of the phase composition and symmetry is discussed in terms of the limited stability of the phases found in the ZrO2–Pr2O3 system, namely, A‐ or C‐R2O3‐like, beyond a certain Pr oxidation degree and oxygen content.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Surface activation of calcium zirconate-calcium stabilized zirconia eutectic ceramics with bioactive wollastonite-tricalcium phosphate coatings

  • Sola, Daniel
  • Chueca, Eloy
  • Wang, Shunheng
  • Peña, José Ignacio
In this work, we have developed and characterized a ceramic composite based on a core of directionally solidified calcium zirconate-calcium stabilized zirconia (CZO-CSZ) eutectic composite coated with a bioactive glass-ceramic. The aim is to research new orthopedic implants as an alternative to conventional 3Y-TZP bioinert ceramics. The CZO-CSZ eutectic rods were grown from the melt of rods of CaO-ZrO2 in the eutectic composition using the laser floating zone technique (LFZ). The mechanical results indicated that directional eutectics prepared with this technique exhibited good mechanical strength and significant hardness and toughness. The LFZ technique was also used to melt the bioactive coating previously placed by dip coating on the CZO-CSZ rod surface. Depending on the thickness of the coating and the applied laser power, an alloying or coating process was achieved. In the first case, the coating was diluted with the surface of the eutectic cylinder, leading to the segregation of the calcium zirconate and zirconia phases and the formation of a bioactive phase embedding zirconia particles. In the second case, a layer of ceramic glass was formed, well attached to the eutectic cylinder. These layers were both studied from the microstructural and bioactivity points of view.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Cobalt-Zirconia coated monoliths fabricated by Direct Ink Writing for catalytic applications

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, Miguel Ángel
  • Llanes, Luis
  • Llorca, Jordi
  • Morales, Miguel
Direct Ink Writing (DIW) is a promising technique for fabricating ceramic catalysts with complex geometries and enhanced catalytic performances, but these still require overcoming some challenges to maximize their catalytic and mechanical functionality. In this work, DIW yttria-doped zirconia (YDZ) catalysts were coated with a Co/YDZ catalyst layer. Two configurations based on a dense monolith and a porous one sintered at 1450ºC and 1300ºC were fabricated through DIW, using optimal rheological hydrogel-inks, to investigate the effect of porosity on the mechanical and catalytic performance in the ethanol steam reforming reaction. The monolith sintered at 1450°C achieved the best mechanical and catalytic performance, as it presented the highest Co concentration (2.3 at%) at the catalyst layer. In addition, this monolith exhibited excellent mechanical properties at the interface between contiguous filaments in the multilayer structure. Therefore, this simple approach is a promising method to produce enhanced catalytically and mechanically robust monoliths.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Direct Ink Writing of cobalt-zirconia monoliths for catalytic applications: A novel single-step fabrication approach

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Vilella, Tània
  • Serrano, Isabel
  • Laguna-Bercero, Miguel Ángel
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Additive manufacturing technologies are revolutionizing the fabrication of ceramic catalysts through hierarchical design to enhance catalytic performance and simultaneously improving the efficiency of the manufacturing process by decreasing the initial investment and production steps. This work proposes a fabrication process of cobalt-zirconia monoliths based on Direct-Ink Writing of Co-enriched hydrogel-based ceramic inks, and the debinding and sintering at 600ºC in a single thermal treatment. The effect of Co precursor amount (3.0 −7.0 wt% Co) on the rheological properties of inks and the catalytic performance in ethanol steam reforming is investigated. The results reveal the successful incorporation of Co into rectilinear monoliths with 50 % infill, obtaining strongly Co-rich surfaces. The remarkable catalytic performance of the 5.0 wt% Co monolith at 300–600ºC confirms the feasibility of this novel single-step approach, reaching an appropriate balance between catalytic activity and printability. This outcome may represent a push towards the fabrication of fully 3D-printed monolithic catalysts.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Can Y2O3-MgO eutectics be new promising structural and optical ceramics?

  • Moshtaghioun B. M.
  • Peña J. I.
  • Merino R. I.
The manuscript addresses the solidification of Y2O3-MgO eutectic composites for the first time, and the study of their microstructure, mechanical properties and infrared transmittance. The composites with eutectic composition (20 % vol MgO) have been solidified using the laser floating zone method, at solidification rates between 25 mm/h and 750 mm/h. Their microstructure has been quantified and the conditions for coupled or cellular regime determined. They are dense, with elastic modulus, as determined from nanoindentation tests of around 200 GPa. The highest 3-point flexural strength (256±25 MPa) values and highest infrared optical transmittance has been observed for the material solidified with the finest, still homogeneous microstructure that could be achieved. This microstructure, which is achieved at a solidification rate of 50mm/h, consists of MgO fibers of 600 nm diameter embedded in the Y2O3 matrix. The thin MgO rods and the associated residual stress field contribute to the material strength as they deviate the propagating crack. The Vickers Hardness ranged from 9.5 to 11.5 GPa, with mild increase with the decrease of the microstructural size which has been rationalized as the MgO rods blocking the movement of dislocations in the matrix, as in other studied composites. Indentation fracture toughness values around 3 MPa.m1/2, independent of the sample microstructure, have been measured. In the longitudinal direction transmittance values higher than 80 % in the wavelength range from 3.5 to 7 µm, for 1 mm thick slices have been measured. Light scattering limits the short wavelength cut-off to around 2 µm for light travelling in the longitudinal direction, while a transmittance gap is observed in the transverse direction, of photonic crystal like nature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

3D-printed Ni/γ-Al2O3 catalysts for CO2 methanation: Effect of Ni loading and sintering temperature

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, Miguel Ángel
  • Vilella, Tània
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Additive manufacturing (AM) technologies are revolutionizing the production of ceramic components, particularly in fields like catalysis, where complex shapes offer remarkable advantages in performance. AM also minimizes material waste while reducing the number of fabrication steps. This work is focused on the fabrication of Ni/γ-Al2O3 monoliths for CO2 methanation in one step by using Direct-Ink Writing (DIW) of Ni-enriched hydrogel-based γ-Al2O3 inks, and the debinding and sintering in a single thermal treatment. For this purpose, the influence of Ni precursor amount (2.5–5.0 wt% Ni) on the rheological properties of inks and the catalytic activity is investigated. Monoliths with woodpile architecture and 50 % infill are sintered at 450 °C and 600 °C to determine the effect of the sintering temperature on the Ni distribution in the catalyst. Results evidence successful incorporation of the metallic active phase into the monolithic structures. Both the Ni amount and sintering temperature are key factors to enhance the CO2 methanation performance. The 5.0 wt% Ni monolith sintered at 450 °C presents both the highest CO2 conversion and methane selectivity at 350–500 °C, due to better reduction degree, dispersion, and smaller size of Ni nanoparticles at the maximum metal loading. These remarkable results demonstrate the potential of DIW for the fabrication of fully 3D-printed monolithic catalysts with well-dispersed metal particles, all while minimizing production steps.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Direct recycling of 3D-printed Co-YDZ catalysts for ethanol steam reforming

  • Razavi, Seyed Ali
  • Fargas, Gemma
  • Serrano, Isabel
  • Laguna-Bercero, Miguel Ángel
  • Vilella, Tània
  • Llanes, Luis
  • Rodríguez, Daniel
  • Ginebra, Maria-Pau
  • Llorca, Jordi
  • Morales, Miguel
Additive manufacturing enhances the catalyst performance via hierarchical design. To address environmental and resource concerns, this work aims to fabricate directly recycled 3D-printed monoliths using Direct-Ink Writing (DIW) from 100 % recovered cobalt-zirconia powders. Virgin cobalt-zirconia monoliths were firstly fabricated by DIW of 3.0–7.0 wt% Co-enriched hydrogel-based ceramic inks, followed by calcination at 600°C in a single thermal treatment. After testing the catalytic performance of monoliths in ethanol steam reforming, 3D-printed cobalt-zirconia monoliths were fragmented and subjected to subsequent milling and sieving steps to recover composite cobalt-zirconia powders with the appropriate properties for reuse in DIW. The recovered powders, inks and monoliths were microstructurally, rheologically and catalytically characterized, and then compared to catalysts constituted by virgin materials. The rheology properties of inks for the recycled and virgin monoliths presented an appropriate printability. Furthermore, the catalytic performance of recycled monoliths was close to that exhibited by virgin catalysts. This study demonstrates the feasibility of directly recycling fully 3D-printed catalysts, potentially reducing the environmental impact with a circular production model to enhance sustainability in the catalyst industry.