Pasar al contenido principal

A LA BUSQUEDA DE NUEVOS CERAMICOS DE ULTRADUROS A BASE DE BORO PARA APLICACIONES ESTRUCTURALES EN LA NUEVA GENERACION DE AVIONES Y USO SEGURO Y EFICIENTE DE LA ENERGIA

PID2019-103847RJ-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE SEVILLA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Can Y2O3-MgO eutectics be new promising structural and optical ceramics?

  • Moshtaghioun, Bibi Malmal
  • Peña, J. I.
  • Merino, R. I.
Hasta el 28 de agosto de 2021 puede accederse gratis a la versión publicada del artículo en este enlace: authors.elsevier.com/c/1dNyu_UwYsE~Gd, The manuscript addresses the solidification of Y2O3-MgO eutectic composites for the first time, and the study of their microstructure, mechanical properties and infrared transmittance. The composites with eutectic composition (20 % vol MgO) have been solidified using the laser floating zone method, at solidification rates between 25 mm/h and 750 mm/h. Their microstructure has been quantified and the conditions for coupled or cellular regime determined. They are dense, with elastic modulus, as determined from nanoindentation tests of around 200 GPa. The highest 3-point flexural strength (256±25 MPa) values and highest infrared optical transmittance has been observed for the material solidified with the finest, still homogeneous microstructure that could be achieved. This microstructure, which is achieved at a solidification rate of 50mm/h, consists of MgO fibers of 600 nm diameter embedded in the Y2O3 matrix. The thin MgO rods and the associated residual stress field contribute to the material strength as they deviate the propagating crack. The Vickers Hardness ranged from 9.5 to 11.5 GPa, with mild increase with the decrease of the microstructural size which has been rationalized as the MgO rods blocking the movement of dislocations in the matrix, as in other studied composites. Indentation fracture toughness values around 3 MPa.m1/2, independent of the sample microstructure, have been measured. In the longitudinal direction transmittance values higher than 80 % in the wavelength range from 3.5 to 7 μm, for 1 mm thick slices have been measured. Light scattering limits the short wavelength cut-off to around 2 μm for light travelling in the longitudinal direction, while a transmittance gap is observed in the transverse direction, of photonic crystal like nature., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants No. MAT77769-R and Gobierno de Aragón, Subvención a Grupos de Investigación No. T02_20R. BMM wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza and is grateful to the Ministerio de Economía y Competitividad for the research funding through the project PID2019-103847RJ-I00 and ‘Junta de Andalucía’ through the project P18-RTJ-1972. We want to thank Rubén Gotor for his help in several tasks of material preparation. Authors would like to acknowledge also the use of the Servicio General de Apoyo a la Investigación SAI, Universidad de Zaragoza, namely, the Service of Electron Microscopy of Materials and the Service of X-ray Diffraction and Fluorescence Analysis., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

CaO–MgO–SiO2–P2O5- based multiphase bio-ceramics fabricated by directional solidification: Microstructure features and in vitro bioactivity studies

  • Díaz-Pérez, María
  • Grima, Lorena
  • Moshtaghioun, Bibi Malmal
  • Peña, J. I.
In vitro activity is important when considering the choice of a multiphasic bioceramic scaffold as phases can dissolve or transform at different rates. The aim of this study is focused on the synthesis and in vitro analysis of multiphasic ceramics obtained from the melt by directional solidification. Depending on the growth rate of the new composition different bioactive phases coexist in the same sample: akermanite, monticellite, tricalcium phosphate and Nurse's A phase, all of them with potential in the medical area as implant for bone or dental repair. With the knowledge of what and how phases dissolve first, it was possible to design materials to get porous scaffolds or more stable ceramics., The authors would like to acknowledge the use of Servicio General de Apoyo en la Investigación- SAI, Universidad de Zaragoza. BMM wants to acknowledge the financial support awarded by the Spanish Ministry of Science and Innovation through the grant PID2019-103847RJ-I00, as well as the one provided by the Regional government of the ‘Junta de Andalucía’ through the project P18-RTJ-1972., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cation-driven electrical conductivity in Ta-doped orthorhombic zirconia ceramics

  • Moshtaghioun, Bibi Malmal
  • Laguna-Bercero, M. A.
  • Peña, J. I.
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Arturo
This paper is devoted to the study of the electrical conductivity of tantalum-doped zirconia ceramics prepared by spark plasma sintering. In this study, the temperature dependence of conductivity in as-prepared specimens and in those previously annealed in air is determined and compared. A semi-empirical model, which is based on the oxidation states of the cations, has been developed and successfully assessed. According to this, the conductivity is basically controlled by the diffusion of tetravalent zirconium cations in both cases, although the concentration of these species varies drastically with the amount of induced oxygen vacancies. This is a quite unexpected fact, since conductivity is normally controlled by anionic diffusion in zirconia ceramics. This option is forbidden here due to the presence of substitutional pentavalent cations. Therefore, conductivity values are much lower than those reported in trivalent or divalent substitutional cation doped zirconia ceramics., The authors would like to acknowledge provided by several institutions: BMM wants to acknowledge the Spanish Ministry of Science and Innovation through the grant PID2019-103847RJ-I00, as well as the financial support awarded by the Regional government of the ‘Junta de Andalucía’ through the project P18-RTJ-1972. BMM and JIP gratefully acknowledge the financial support provided the Ministry of Science in Spain through the projects MAT2016-77769-R and Gobierno de Aragón, Spain (Grupo Reconocido DGA T02_17R) and the associated EU Regional Development Funds. MLB acknowledges the funding support provided by the projects MAT2015-68078-R and PID2019-107106RB-C32 funded by the Spanish Ministry of Science and Innovation. Finally, DGG and ADR are grateful to the Spanish Ministry of Science for the research funding through the project MAT2015-71411-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

New hardness model for fine fibrous eutectic ceramics prepared by laserheated floating zone (LFZ)

  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Peña, J. I.
  • Merino, R. I.
Resumen del trabajo presentado a la Conferencia Ceramics in Europe, celebrada en Krakow (Poland) del 10 al 14 de julio de 2022., B.M.M and D.G.G. are grateful to the Ministerio de Economía y Competitividad for the research funding through the project PID2019-103847RJ- I00 financiado por MCIN/ AEI /10.13039/501100011033 and ‘Junta de Andalucía’ through the project P18-RTJ-1972. RIM and JIP acknowledge to the Gobierno de Aragón, for the financial support to the Research Group T02_20R., No
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

CaO–MgO–SiO2–P2O5- based multiphase bio-ceramics fabricated by directional solidification: Microstructure features and in vitro bioactivity studies

  • Díaz-Pérez, M.
  • Grima, L.
  • Moshtaghioun, B.M.
  • Peña, J.I.
In vitro activity is important when considering the choice of a multiphasic bioceramic scaffold as phases can dissolve or transform at different rates. The aim of this study is focused on the synthesis and in vitro analysis of multiphasic ceramics obtained from the melt by directional solidification. Depending on the growth rate of the new composition different bioactive phases coexist in the same sample: akermanite, monticellite, tricalcium phosphate and Nurse''s A phase, all of them with potential in the medical area as implant for bone or dental repair. With the knowledge of what and how phases dissolve first, it was possible to design materials to get porous scaffolds or more stable ceramics.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Can Y2O3-MgO eutectics be new promising structural and optical ceramics?

  • Moshtaghioun B. M.
  • Peña J. I.
  • Merino R. I.
The manuscript addresses the solidification of Y2O3-MgO eutectic composites for the first time, and the study of their microstructure, mechanical properties and infrared transmittance. The composites with eutectic composition (20 % vol MgO) have been solidified using the laser floating zone method, at solidification rates between 25 mm/h and 750 mm/h. Their microstructure has been quantified and the conditions for coupled or cellular regime determined. They are dense, with elastic modulus, as determined from nanoindentation tests of around 200 GPa. The highest 3-point flexural strength (256±25 MPa) values and highest infrared optical transmittance has been observed for the material solidified with the finest, still homogeneous microstructure that could be achieved. This microstructure, which is achieved at a solidification rate of 50mm/h, consists of MgO fibers of 600 nm diameter embedded in the Y2O3 matrix. The thin MgO rods and the associated residual stress field contribute to the material strength as they deviate the propagating crack. The Vickers Hardness ranged from 9.5 to 11.5 GPa, with mild increase with the decrease of the microstructural size which has been rationalized as the MgO rods blocking the movement of dislocations in the matrix, as in other studied composites. Indentation fracture toughness values around 3 MPa.m1/2, independent of the sample microstructure, have been measured. In the longitudinal direction transmittance values higher than 80 % in the wavelength range from 3.5 to 7 µm, for 1 mm thick slices have been measured. Light scattering limits the short wavelength cut-off to around 2 µm for light travelling in the longitudinal direction, while a transmittance gap is observed in the transverse direction, of photonic crystal like nature.