Pasar al contenido principal

DISEÑO MICROESTRUCTURAL Y CARACTERIZACION IN-SITU DE NUEVOS MATERIALES PARA SOFC

MAT2015-68078-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 35
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tailoring the microstructure of a solid oxide fuel cell anode support by calcination and milling of YSZ

  • Hanifi, Amir R.
  • Laguna-Bercero, M. A.
  • Sandhu, Navjot K.
  • Etsell, Thomas H.
  • Sarkar, Partha
In this study, the effects of calcination and milling of 8YSZ (8 mol% yttria stabilized zirconia) used in the nickel-YSZ anode on the performance of anode supported tubular fuel cells were investigated. For this purpose, two different types of cells were prepared based on a Ni-YSZ/YSZ/NdNiO-YSZ configuration. For the anode preparation, a suspension was prepared by mixing NiO and YSZ in a ratio of 65:35 wt% (Ni:YSZ 50:50 vol.%) with 30 vol.% graphite as the pore former. As received Tosoh YSZ or its calcined form (heated at 1500 °C for 3 hours) was used in the anode support as the YSZ source. Electrochemical results showed that optimization of the fuel electrode microstructure is essential for the optimal distribution of gas within the support of the cell, especially under electrolysis operation where the performance for an optimized cell (calcined YSZ) was enhanced by a factor of two. In comparison with a standard cell (containing as received YSZ), at 1.5 V and 800 °C the measured current density was -1380 mA cm and -690 mA cm for the cells containing calcined and as received YSZ, respectively. The present study suggests that the anode porosity for improved cell performance under SOEC is more critical than SOFC mode due to more complex gas diffusion under electrolysis mode where large amount of steam needs to be transfered into the cell., The authors would like to acknowledge the Climate Change and Emissions Management Corporation (CCEMC) of Canada and Fundacion Domingo Martinez and Ministerio de Economia y Competitividad (grant no. MAT2015-68078-R) of Spain for funding this research., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The influence of the reducing conditions on the final microstructure and performance of nickel-yttria stabilized zirconia cermets

  • Monzón, Hernán
  • Laguna-Bercero, M. A.
Ni-YSZ (yttria stabilized zirconia) cermets are the most widespread composite materials to be used as SOFC fuel electrodes. These materials are generally fabricated by the reduction of NiO to Ni in a NiO-YSZ composite, where the reducing conditions have a great effect in the final microstructure of the electrode. In the present work, several reducing conditions were explored in order to find the most suitable microstructure for anode-supported microtubular solid oxide fuel cells (SOFCs). Samples were firstly reduced in either pure or diluted H (dry or humidified), at temperatures ranging from 400 to 800 °C while their DC conductivity was monitored. The highest conductivity value was measured for the sample reduced in pure humidified hydrogen at 800 °C. However, this sample experienced conductivity degradation in comparison with samples reduced under dry conditions. For the studied temperature range, nucleation of nano-porous nickel particles is firstly formed during reduction. However, from our experiments it was concluded that those nanoparticles are not stable with time, at least at temperatures between 600 °C and 800 °C. Electrochemical characterization of complete microtubular cells under real wet conditions was also performed under current load, confirming that the microstructure of the Ni-YSZ cermet is still evolving during operation., Authors would like to thank the project MAT2015-68078-R, financed by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder program of the European Union., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Highly stable microtubular cells for portable solid oxide fuel cell applications

  • Monzón, Hernán
  • Laguna-Bercero, M. A.
In this work, extruded support tubes based on Nickel Oxide-YSZ (yttria stabilized-zirconia) were manufactured by Powder Extrusion Moulding (PEM). An YSZ layer is then deposited by dip coating as the electrolyte and subsequently, standard La0.8Sr0.2MnO3-δ (LSM)/YSZ composites were deposited by dip coating as oxygen electrodes. Microstructure of the anode support was optimized in order to achieve the maximum fuel utilization and as a consequence, a high performance of the cells. Experiments as a function of the fuel composition showed power densities above 500 mWcm−2 at 800 °C at 0.7 V, with high fuel utilization (∼75%). Long-term durability studies were also performed for a period above 1000 hours. The experiment was conducted at 800 °C using pure humidified hydrogen at a fixed voltage of 0.8 V. It was observed that the current density of the cell is significantly evolving during the initial period of about 100 hours, as a consequence of reconditioning of nickel particles at the anode support. Once the system is stabilized, no degradation was observed up to 1000 hours under operating conditions, obtaining current densities in the range of 400 mAcm−2 at 0.8 V and 800 °C., The project MAT2015-68078-R, financed by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder program of the European Union, is also acknowledged., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Mecanizado láser de electrolitos para la mejora del rendimiento electroquímico de pilas de combustible de óxido sólido

  • Cebollero, Jose Antonio
  • Lahoz, Fernando J.
  • Laguna-Bercero, M. A.
  • Larrea, Ángel
Trabajo presentado al III Congreso Iberoamericano de Hidrógeno y Pilas de Combustible (IberConappice), celebrado en Huesca del 17 al 20 de octubre de 2017., [ES]: El rendimiento de las celdas de combustible de óxido sólido (SOFC) está limitado por dos principales factores. Uno de ellos es la resistencia óhmica, debida a la conductividad iónica del electrolito y por tanto directamente proporcional a su espesor. También aparece la denominada resistencia de polarización, debido a las reacciones electroquímicas que tienen lugar en los electrodos. Está directamente relacionada con la densidad de puntos triples (TPB), por lo que depende de la microestructura y del área de contacto entre electrolito y electrodo. En este trabajo, se ha utilizado la técnica de mecanizado láser para modificar electrolitos SOFC de circona estabilizada con itria (YSZ) y de este modo fabricar pilas con un mayor rendimiento. Por una parte se han preparado electrolitos finos autosoportados con menor resistencia óhmica, adelgazando la cerámica mediante mecanizado láser para crear zonas de ~20 μm de espesor. El resto del electrolito se mantiene con el espesor original de 150 μm y actúa como soporte mecánico de la celda. Por otra parte, para reducir la resistencia de polarización, se ha mecanizado la superficie originalmente lisa de los electrolitos, generando un perfil corrugado que incrementa el área de contacto con el electrodo. Se han fabricado celdas simétricas de LSM (manganita de lantano y estroncio) -YSZ / YSZ / LSM-YSZ, depositando los electrodos mediante inmersión (dip coating). Para conseguir una buena unión de los electrodos con los electrolitos mecanizados, ha sido necesario recurrir a técnicas de sinterización asistida por presión. Se ha evaluado el rendimiento de las celdas mediante espectroscopia de impedancias electroquímica (EIS), obteniendo una reducción de la resistencia de polarización de hasta el 30% en el rango de temperaturas comprendido entre 700ºC y 900ºC., [EN]: Performance of Solid Oxide Fuel Cells (SOFC) is limited by two main factors. One of them is the ohmic resistance, caused by ionic conductivity of the electrolyte, and consequently directly proportional to its thickness. In addition, activation polarisation resistance appears due to electrochemical reactions happening in the electrodes. This resistance is directly related with the Triple Phase Boundary (TPB) density; therefore it depends on the microstructure and on the electrode-electrolyte contact area. In this work, laser machining has been used to modify SOFC yttria stabilised zirconia (YSZ) electrolytes, and in this way to fabricate cells with higher performance. On the one hand thin self-supported electrolytes with less ohmic resistance have been prepared, thinning the ceramic by laser machining to create zones with ~20 μm in thickness. The rest of the electrolyte remains with the original thickness of 150 μm and acts as mechanical support of the cell. On the other hand, in order to reduce the polarisation resistance, the initially smooth surface of the electrolyte has been machined, generating a corrugate profile that increments the contact area with the electrode. Symmetrical LSM (lanthanum strontium manganite)-YSZ / YSZ / LSM-YSZ cells have been fabricated; the electrodes were deposited by dip coating. In order to obtain a good contact between the electrodes and the modified electrolytes, pressureassisted sintering was needed. The performance of the cells has been measured by electrochemical impedance spectroscopy (EIS), obtaining a decrease in the polarisation resistance up to 30% in a temperature range between 700ºC - 900ºC., Este trabajo ha sido financiado por el proyecto MAT2015-68078-R, financiado por el gobierno de España (Ministerio de Economía y Competitividad) y el Programa Feder de la Unión Europea., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Design and characterization of macroporous alumina membranes for passive samplers of water contaminants

  • Orera, V. M.
  • Silva-Treviño, J.
  • Franquet-Griell, Helena
  • Lacorte Bruguera, Silvia
Macroporous ceramic membranes with hierarchical pore structure were developed and characterized for the time-integrated analysis of water contaminants. The alumina membranes were boosted to allow a suitable diffusion rate for envisaged applications. Sacrificial fugitives as cornstarch and graphite and partial sintering technique were utilized for the control of pore structure and morphology. The present study includes: (i) Development of ceramic membrane preparation methods based on wet forming techniques and partial sintering in order to control of membrane parameters such as porosity, tortuosity factor and thickness; (ii) Microstructural characterization of the ceramic membranes using two complementary techniques: Hg-porosimetry and SEM; (iii) the diffusion tests performed under laboratory conditions by an innovative, easy and accurate method based in the use of methylene blue (C16H18ClN3S) water solutions as test compound to study the characteristics of ceramic membranes. Using slip casting and partial sintering processing three different Al2O3 membrane configurations with high values 34.5, 36.9 and 39.6 vol% of interconnected porosity and 1.75, 1.7 and 1.3 mm thickness were prepared. The pore morphology consisted of spherical cavities of 5-10 μm diameter and small pores of 70–200 nm. This study also gathers the basis for the calculation of diffusion coefficients, membrane geometrical factor and sampling rates using methylene blue water solutions whose concentration can be accurately determined by optical absorption measurements at 664 nm. Diffusion coefficients for methylene blue range from 2.3 ± 0.5E-8 to 3.0 ± 0.5E-8 cm2 s−1 increasing as connected porosity increases and membrane thickness decreases. The membrane geometrical factors are low, between 0.6 and 1E-02 and Archie’s constants large 4.5–5.5. This has been associated to the bimodal pore structure with coexistence of large and small pores that may increase the tortuosity factors in membranes. The macroporous ceramic membranes herein developed are suitable for the fabrication of passive samplers aimed at preconcentrating organic contaminants in water., Financial support from the Spanish Ministerio de Economía y Competitividad under the projects CTM2014-60199-P regarding the monitoring of cytostatic compounds and MAT2015-68078-R for the development of the ceramic membranes is acknowledged. HF acknowledges FPI grant BES-2012-053000., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of anode functional layers on electrochemical performance and mechanical strength in microtubular solid oxide fuel cells fabricated by gel-casting

  • Morales, Miguel
  • Laguna-Bercero, M. A.
Anode-supported microtubular solid oxide fuel cells (mT-SOFCs) using samaria-doped ceria (SDC) as electrolyte were fabricated, varying the composition and number of anode functional layers (AFLs), by combining the aqueous gel-casting and spray-coating techniques. Suitable aqueous slurry formulation of NiO–SDC was prepared using agarose as a gelling agent for gel-casting of tubular supports. Afterward, 40:60 and 50:50 NiO:SDC (wt %) as AFLs and SDC electrolyte were deposited by spray-coating and subsequently co-sintered. Finally, mT-SOFCs with 2.5 mm outer diameter and thicknesses of 380 μm support; 0, 12, and 24 μm AFLs; 15 μm electrolyte; and 30 μm cathode were obtained. The influence of AFLs on the performance and mechanical integrity was investigated for the three cells. For this purpose, electrochemical and mechanical tests at both macroscopic and micro-/nanometric scales (at the AFLs region) were determined by flexural strength and nanoindentation techniques, respectively. The results evidence that the use of AFLs with an adequate composition and microstructure in the mT-SOFCs is required to improve the performance and mechanical strength of the cell. The cell with a single-layer AFL of 50:50 NiO:SDC (wt %) and 12 μm thickness exhibited the best performance (0.52 W·cm–2) at 650 °C using hydrogen as fuel and air as oxidant., The present work was financed by the Spanish Government (Ministerio de Economia y Competitividad) and the Feder program of the European Union with Project MAT2015-68078-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reversible operation of microtubular solid oxide cells using La0.6Sr0.4Co0.2Fe0.8O3-δ-Ce0.9Gd0.1O2-δ oxygen electrodes

  • López-Robledo, M. J.
  • Laguna-Bercero, M. A.
  • Larrea, Ángel
  • Orera, V. M.
Yttria stabilized zirconia (YSZ) based microtubular solid oxide fuel cells (mT-SOFCs) using La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) and Ce0.9Gd0.1O2-δ (GDC) as the oxygen electrode, along with a porous GDC electrolyte-electrode barrier layer, were fabricated and characterized in both fuel cell (SOFC) and electrolysis (SOEC) operation modes. The cells were anode-supported, the NiO-YSZ microtubular supports being made by Powder Extrusion Moulding (PEM). The cells showed power densities of 695 mW cm−2 at 800 °C and 0.7 V in SOFC mode, and of 845 mA cm−2 at 800 °C and 1.3 V in SOEC mode. AC impedance experiments performed under different potential loads demonstrated the reversibility of the cells. These results showed that these cells, prepared with a method suitable for using on an industrial scale, are highly reproducible and reliable, as well as very competitive as reversible SOFC-SOEC devices operating at intermediate temperatures., The authors would like to acknowledge the grant MAT2015-68078-R financed by the Spanish Government (Ministerio de Economía y Competitividad) and Feder program of the European Community for funding the project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The effect of pore-former morphology on the electrochemical performance of solid oxide fuel cells under combined fuel cell and electrolysis modes

  • Laguna-Bercero, M. A.
  • Hanifi, Amir R.
  • Menand, Lucile
  • Sandhu, Navjot K.
  • Anderson, Neil E.
  • Etsell, Thomas H.
  • Sarkar, Partha
The effect of the pore-former used in the Ni-YSZ fuel electrode on the electrochemical performance of solid oxide cells is studied. Three cells with the configuration of Ni-YSZ/YSZ/Nd2NiO4+δ-YSZ were fabricated with different pore-formers, such as graphite, PMMA (polymethyl methacrylate) or an equal mixture of both, which were added to the Ni-YSZ support during the fabrication process. The results show that the Ni-YSZ support containing graphite leads to a more porous support and formation of coarser pores in the vicinity of the electrolyte. This leads to a reduction in the triple phase boundary (TPB) length with a corresponding increase of activation polarization and, as a consequence, the overall cell performance decreases in both fuel cell and electrolysis modes. The cell having PMMA delivered the highest performance under both operation modes (818 and −713 mAcm−2 were obtained in SOFC and SOEC modes at 800 °C), due to finer pores next to the electrolyte. The cell having the mixture of both pore-formers delivered intermediate results. All the cells show similar concentration polarization values meaning that even the least porous cell (PMMA) provided sufficient porosity for gas flow. In addition, long term reversible experiments were performed, showing no degradation for a period above 400 h., The authors would like to acknowledge the Natural Sciences and Engineering Research Council of Canada for funding part of this research. The work was also funded by the Fundación Domingo Martínez, the Spanish Government (Ministerio de Economía y Competitividad) and the Feder Program of the European Union (MAT2015-68078-R project). LM acknowledges the internship agreement between CSIC and University of Bordeaux for the research stay at ICMA., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Characterization of laser-processed thin ceramic membranes for electrolyte-supported solid oxide fuel cells

  • Cebollero, Jose Antonio
  • Lahoz, Ruth
  • Laguna-Bercero, M. A.
  • Peña, J. I.
  • Larrea, Ángel
  • Orera, V. M.
By laser machining we have prepared thin and self-supported yttria stabilized zirconia (YSZ) electrolytes that can be used in electrolyte-supported solid oxide fuel cells for reducing the operation temperature. The membranes, which are supported by thicker areas of the same material, have an active area of ∼20 μm in thickness and up to 8 mm in diameter. Buckling limits the maximum size of the thin areas to below 1 mm, the overall effective active area being formed by multiple thin areas bounded by ribs. Electron Backscattering Diffraction experiments determined that there are not significant strains inside the membranes and that the heat-affected zone is confined to a shallow layer of ∼1–2 μm. The bending strength of the membranes decreases by ∼26% as a result of the surface microcracking produced by the laser machining. The membranes have a roughness of ∼2.5 μm and are coated by a layer of nanoparticles produced by the laser ablation. This coating and small roughness is not detrimental for the cathodic polarization of the cells. Conversely, the cathode polarization resistance decreases ∼5% in the 650–850 °C temperature range., This study was funded by the MAT2015-68078-R financed by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder Program of the European Union., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of a macroporous ceramic passive sampler for the monitoring of cytostatic drugs in water

  • Franquet-Griell, Helena
  • Pueyo, Víctor
  • Silva-Treviño, J.
  • Orera, V. M.
  • Lacorte Bruguera, Silvia
The aim of this study was to develop and calibrate a macroporous ceramic passive sampler (MCPS) for the monitoring of anticancer drugs in wastewater. This system was designed by the Spanish Research Council (CSIC) and consists in a porous ceramic tube to allow a high diffusion of contaminants. The MCPS has been calibrated for 16 cytostatic drugs over time periods up to 9 d in spiked water under controlled laboratory conditions. Optimal uptake was accomplished for 7 compounds, namely ifosfamide, cyclophosphamide, capecitabine, prednisone, megestrol, cyproterone and mycophenolic acid, whereas cytarabine was not adsorbed in the receiving phase and the rest were hydrolyzed over the deployment period. The sampling rate for these 7 compounds was between 0.825 and 3.350 mL day-1 and the diffusion coefficients varied from 1.01E-07 to 4.12E-07 cm2 s-1. To prove the applicability of the MCPSs, samplers (n = 3) were deployed in influent and effluent waters of a WWTP for a period of 6 d and results were compared to grab sampling and extraction with Solid Phase Extraction (SPE). In influent waters, MCPS were clogged due to the high amount of suspended solids in these waters. In effluents, MCPS detected cyclophosphamide and mycophenolic acid at concentrations of 19 ± 3 and 136 ± 28 ng L-1 with a good agreement with the levels obtained by grab sampling. The study discusses the use and performance of the MCPS for the monitoring of stable cytostatic compounds in a complex matrix such as wastewater., This study has been performed thanks to financial support from the Ministerio de Economía y Competitividad of Spain under the projects CTM2014-60199-P and MAT2015-68078-R. H. Franquet acknowledges the FPI grant BES-2012-053000., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructure, texture, and crystallography in Ni–GDC and Co–GDC porous cermets obtained from directionally solidified eutectic ceramics

  • Serrano-Zabaleta, S.
  • Larrea, Ángel
  • Larrañaga, Aitor
  • Dickey, Elizabeth C.
Lamellar NiO–GDC (Gadolinium-doped Ceria) and CoO–GDC directionally solidified eutectic ceramics (DSECs) were produced by the laser floating-zone technique and subjected to reduction in order to obtain porous cermets of Ni–GDC and Co–GDC, which have potential applications as anodes in solid oxide fuel cells (SOFC). The reduction of these DSECs into porous cermets was studied at 650 °C in NiO–GDC and at 500 and 700 °C in CoO–GDC, all of them processed with similar reduction kinetics. In comparison to similar Ni–YSZ and Co–YSZ lamellar cermets previously studied, no sharp reduction front was observed. The interface between the reduced and nonreduced zones is broader, with pores homogenously distributed in wide areas. Afterwards, the microstructure, texture, and crystallography of the samples were studied by electron microscopy as well as by electron and X-ray diffraction when completely reduced. The single crystal NiO and CoO lamellae transformed into porous polycrystalline metallic lamellae. Moreover, microscopy observations revealed a porous nanostructure of Co particles obtained by reduction at low temperatures (500 °C). Many of the Co and Ni particles seemed to have roughly maintained the previous crystallographic orientation with respect to the GDC phase, although the disorder of the crystallographic orientation increased significantly. In addition, a significant amount of the Ni particles reoriented to form an epitaxial interface with the (100)–GDC surface., This study was funded by MAT2012-30763 and MAT2015-68078-R projects, which are financed by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder Program of the European Union. E.C. Dickey acknowledges support from the National Science Foundation under grant #1139792., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microtubular solid oxide fuel cells fabricated by gel-casting: the role of supporting microstructure on the mechanical properties

  • Morales, M.
  • Laguna-Bercero, M. A.
Different cell configurations of anode-supported microtubular solid oxide fuel cells (mT-SOFCs) using samaria-doped ceria (SDC) as the electrolyte were fabricated. Several cells were processed varying the porosity and wall thickness (outer diameter) of NiO–SDC tubular supports. Suitable aqueous slurry formulations of NiO–SDC for gel-casting were prepared using agarose, as a gelling agent, and sucrose, as a pore former. The subsequent NiO–SDC anode functional layer (AFL), the SDC electrolyte and the La0.6Sr0.4Co0.2Fe0.8O3−δ–SDC cathode were deposited by spray-coating. Afterwards, the electrochemical performance of different single cells was tested under humidified hydrogen as the fuel and air as the oxidant. The mechanical strength of the supporting tubes at different processing stages (green, pre-/post-sintering, post-reduction, post-redox cycle conditions) were also determined to study the macro-mechanical failure behaviour of the cells. In addition, the mechanical strength of half-cells with different porosity, sintering temperature and wall thickness in the tubular supports was also determined. For this purpose, the modulus of rupture was measured by a three point bending test. This study shows that the electrochemical properties and mechanical strength are feasible for further development of anode-supported mT-SOFCs fabricated by gel-casting., The present work was financed by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder program of the European Union with the project MAT2015-68078-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tailoring the electrode-electrolyte interface of Solid Oxide Fuel Cells (SOFC) by laser micro-patterning to improve their electrochemical performance

  • Cebollero, Jose Antonio
  • Lahoz, Ruth
  • Laguna-Bercero, M. A.
  • Larrea, Ángel
Cathode activation polarisation is one of the main contributions to the losses of a Solid Oxide Fuel Cell. To reduce this loss we use a pulsed laser to modify the surface of yttria stabilized zirconia (YSZ) electrolytes to make a corrugated micro-patterning in the mesoscale. The beam of the laser source, 5 ns pulse width and emitting at λ = 532 nm (green region), is computer-controlled to engrave the selected micro-pattern on the electrolyte surface. Several laser scanning procedures and geometries have been tested. Finally, we engrave a square array with 28 μm of lattice parameter and 7 μm in depth on YSZ plates. With these plates we prepare LSM-YSZ/YSZ/LSM-YSZ symmetrical cells (LSM: La1-xSrxMnO3) and determine their activation polarisation by Electrochemical Impedance Spectroscopy (EIS). To get good electrode-electrolyte contact after sintering it is necessary to use pressure-assisted sintering with low loads (about 5 kPa), which do not modify the electrode microstructure. The decrease in polarisation with respect to an unprocessed cell is about 30%. EIS analysis confirms that the reason for this decrease is an improvement in the activation processes at the electrode-electrolyte interface., This work was funded by the MAT2015-68078-R project, which is financed by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder Program of the European Union., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Sondas espectroscópicas locales para monitorizar in-situ la actividad de oxígeno en electrolitos en pilas de combustible y electrolizadores de óxido sólido

  • Merino, R. I.
  • Robles-Fernandez, Adrian
  • Orera, Alodia
  • Peña, J. I.
Resumen del trabajo presentado al V Congreso Hispano-Luso de Cerámica y Vidrio, celebrado en Barcelona del 8 al 10 de octubre de 2018., Las celdas electroquímicas de óxido sólido reversibles son dispositivos capaces de generar energía eléctrica a partir de la oxidación de un combustible (modo de funcionamiento pila de combustible, SOFC) o bien de generar combustible (H2) con el suministro de energía eléctrica (modo electrolizador, SOEC). Estos dispositivos constan de un electrólito, conductor de iones óxido; electrodos para catalizar la adsorción, disociación, oxidación y reducción de los reactivos (ánodos o cátodos), con conducción mixta y porosidad para el transporte de gases; y los colectores de corriente. Para un funcionamiento óptimo es necesario que actividades catalíticas, conductancias y transporte de gases, estén ajustados de modo que las pérdidas óhmicas y de polarización sean mínimas, así como la degradación en uso. En particular, son críticos los procesos en las intercaras entre electrólito y electrodos, donde tienen lugar los intercambios de iones. En SOECs basados en circona estabilizada con voltajes de polarización altos se ha encontrado que la actividad de oxígeno en la intercara con el electrodo de oxígeno es tan alta que este se delamina. Laguna-Bercero et al. investigaron esta degradación haciendo un estudio espectroscópico con resolución espacial de celdas después de los ensayos electroquímicos. En esta comunicación presentaremos resultados de la búsqueda de sondas espectroscópicas que permitan monitorizar la actividad de oxígeno en condiciones de operación, es decir a las temperaturas de trabajo de los dispositivos. Para acceder ópticamente al interior del electrolito se persigue hacer el estudio usando monocristales como electrolito. Se han investigado diferentes dopantes y codopantes en monocristales de circona estabilizada (Ce, Pr, Mn, V, Ce-Pr, Mn-Nd), en los que existe variación del estado de oxidación de uno o ambos dopantes en distintos rangos de actividad de oxígeno. También se han preparado cerámicas y cristales de circona dopada con Tb y sintetizado apatitas dopadas. Se observa que la señal de raman electrónico de Ce3+ desaparece a temperaturas mayores de 300 ºC, mientras que luminiscencias de Er3+, Pr3+ y Tb3+ persisten a temperaturas mucho más altas. El codopado presenta algunas desventajas frente a dopantes simples con cambios espectroscópicos frente a la actividad de oxígeno y señal óptica cuantificable a alta temperatura., Se agradece al MINECO la financiación a través del proyecto NEXTSOFC MAT2015-68078-R., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reversible operation performance of microtubular solid oxide cells with a nickelate-based oxygen electrode

  • Morales, M.
  • Larrea, Ángel
  • Laguna-Bercero, M. A.
This paper describes the reversible operation of a highly efficient microtubular solid oxide cell (SOC) with a nickelate-based oxygen electrode. The fuel cell was composed of a microtubular support of nickel and yttria stabilized zirconia (Ni-YSZ), an YSZ dense electrolyte, and a double oxygen electrode formed by a first composite layer of praseodymium nickelate (PNO) and gadolinium-doped ceria (CGO) and a second one of PNO. A good performance of the cell was obtained at temperatures up to 800 °C for both fuel cell (SOFC) and electrolysis (SOEC) operation modes, specially promising in electrolysis mode. The current density in SOEC mode at 800 °C is about −980 mA cm−2 at 1.2V with 50% steam. Current density versus voltage curves (j-V) present a linear behavior in the electrolysis mode, with a specific cell area resistance (ASR) of 0.32 Ω cm−2. Durability experiments were carried out switching the voltage from 0.7V to 1.2V. No apparent degradation was observed in fuel cell mode and SOEC mode up to a period of about 100 h. However, after this period especially in electrolysis mode there is an accumulated degradation associated to nickel coarsening, as confirmed by SEM and EIS experiments. Those results confirm that nickelate based oxygen electrodes are excellent candidates for reversible SOCs., This work was funded by the MAT2015-68078-R project, financed by the Spanish Government (Ministerio de Ciencia, Innovación y Universidades) and the Feder Program of the European Union., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

SOFC cathodic layers using wet powder spraying technique with self synthesized nanopowders

  • Wain-Martin, A.
  • Morán-Ruiz, Aroa
  • Laguna-Bercero, M. A.
  • Campana, Roberto
  • Larrañaga, Aitor
  • Slater, P. R.
  • Arriortua, María Isabel
In this work, a wet powder spraying method has been investigated as a facile low cost route to deposit electrode layer on SOFC electrolyte support. A particular focus has been examining the interfacial stability of the deposited layers, and determining the influence of the thickness of the different layers, as well as the ball milling regime used to produce the electrode inks. The developed system consist of an yttria stabilized zirconia electrolyte support, a La0.6Sr0.4FeO3 (LSF) cathode, a Sm0.2Ce0.8O1.9 (SDC) barrier layer between the electrolyte and the cathode, and LaNi0.6Fe0.4O3 (LNF) as a contact layer, for a future integration with the SOFC interconnector. The electrolyte supports (300 μm thickness and 9 mm diameter) supports were prepared by uniaxial pressing, while the deposition of thin barrier layers, cathode and contact layer were carried out by manual spray coating., This research has been funded by the Ministerio de Economía, Industria y Competitividad [MAT2016-76739-R and MAT2015-68078-R] [AEI/FEDER, UE] and Dpto. Educación of the Basque Government [IT-630-13]. The authors thanks the support received by the European Regional Development Fund (ERDF). The technical support of SGIker of UPV/EHU is gratefully acknowledged. A. Wain-Martin thanks Ministerio de Economía y Competitividad for funding his work [BES-2014-068433]., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optimization of laser-patterned YSZ-LSM composite cathode-electrolyte interfaces for solid oxide fuel cells

  • Cebollero, Jose Antonio
  • Laguna-Bercero, M. A.
  • Lahoz, Fernando J.
  • Silva-Treviño, J.
  • Moreno, Rodrigo
  • Larrea, Ángel
Patterned cathode/electrolyte interfaces formed by a hexagonal array of ∼22 μm deep wells with 24 μm lattice parameter have been prepared by pulsed laser machining to enlarge the contact surface and, consequently, to reduce the cathode polarization of Solid Oxide Fuel Cells. These new interfaces have been tested in YSZ-LSM/YSZ/YSZ-LSM symmetrical cells, where the cathode is deposited by dip-coating. Appropriate ceramic suspensions have been formulated to penetrate into deep wells without presenting interfacial delamination after sintering. We analyse their applicability by comparing their rheology with the microstructure and electrochemical performance of the cells. The activation component of the polarization resistance is reduced by ∼50% using ethanol-based suspensions with 20 wt% solids loading, although the gas diffusion component increases due to excessive densification. Alternative ceramic suspensions with 17.5 wt% solids loading provide optimum electrode gas diffusion but lower activation components, resulting in an overall decrease of ∼20% in polarization resistance., This work was funded by the MAT2015-68078-R and MAT2015-67586-C3-2-R projects, which are financed by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder Program of the European Union.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Development of advanced nickelate-based oxygen electrodes for solid oxide cells

  • Laguna-Bercero, M. A.
  • Orera, Alodia
  • Morales-Zapata, M.
  • Larrea, Ángel
Trabajo presentado al Solid Oxide Fuel Cells 16 (SOFC-XVI), celebrado en Kyoto (Japón) del 8 al 13 de septiembre de 2019., The present work deals with the development of lanthanide nickelate based oxygen electrodes (Ln2NiO4+δ, with Ln = Nd, La or Pr) as the oxygen electrode for both solid oxide fuel cell (SOFC) and solid oxide electrolysis (SOEC) applications. The have been widely investigated as they present high oxygen diffusion parameters, making them attractive as SOFC oxygen electrodes. However, the main drawback of these nickelate phases is their reactivity with standard YSZ (yttria stabilized zirconia) or CGO (cerium gadolinium oxide) electrolytes, as typical sintering temperatures are usually higher than 1000 ºC in order to get strong adhesion at the electrode/electrolyte interface. Two strategies will be employed to avoid the undesired reactivity: the direct formation of the nickelate phase into YSZ scaffolds by infiltration and the development of active barrier layer., This work was funded by the MAT2015-68078-R project, financed by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder Program of the European Union, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Interfacial stability and ionic conductivity enhanced by dopant segregation in eutectic ceramics: the role of Gd segregation in doped CeO2/CoO and CeO2/NiO interfaces

  • Orera, Alodia
  • Wang, Funing
  • Ferreiro-Vila, Elías
  • Serrano-Zabaleta, S.
  • Larrañaga, Aitor
  • Laguna-Bercero, M. A.
  • Dickey, Elizabeth C.
  • Rivadulla, Francisco
  • Muñoz, M. Carmen
  • Larrea, Ángel
The conductivity of ceramic ionic materials is highly influenced by dopant segregation at the grain boundaries or interfaces, which usually induces a depletion of charge carriers by space charge effects. Hence, obtaining interfacial configurations that promote the formation of oxygen vacancies is highly desirable. In this paper we have combined high resolution electron microscopy (HREM), kelvin probe force microscopy (KPFM) and density functional theory (DFT) to elucidate the equilibrium state of CGO–CoO and CGO–NiO eutectic ceramics (CGO: cerium-gadolinium oxide). HREM proves that the interface is sharp, formed by a single common oxygen plane, and that in CGO–CoO the concentration of gadolinium ions at the interface is almost three times greater than in the bulk, while they distribute homogeneously in the CGO–NiO system. Accordingly, KPFM experiments suggest that interfacial ionic conductivity is much higher in CoO–CGO than in NiO–CGO. DFT demonstrates that Gd segregation in the CGO–CoO reduces the interface energy, contributing to its stability. The Gd-oxygen vacancy complexes compensate the interfacial ionic charge density discontinuity. Additionally, the induced local distortions around the defect release the strain associated with the lattice mismatch. Therefore, we show that in CGO-based eutectics the structure and ionicity of the constituent oxides are essential to promote the interface dopant segregation, indicating a new way to produce nanocomposites with enhanced interfacial ionic conductivity., This work was funded through MAT2015-68078-R, MAT2015-66888-C3-1R, MAT2016-80762-R and RTI2018-097895-B-C41 projects by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder Programme of the European Union. Financial support from Xunta de Galicia (Centro singular de investigación de Galicia, accreditation 2016–2019, ED431G/09) is also recognized. F. W. acknowledges the financial support of the China Scholarship Council (CSC) during her stay at the ICMM., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Suitability of strontium and cobalt-free perovskite cathodes with La9.67Si5AlO26 apatite electrolyte for intermediate temperature solid oxide fuel cells

  • Robles-Fernandez, Adrian
  • Orera, Alodia
  • Merino, R. I.
  • Slater, Peter
Aluminium-doped lanthanum silicate (LSAO) apatite-type compounds have been considered as promising candidates for substituting yttria-stabilized zirconia (YSZ) as electrolytes for intermediate temperature solid oxide fuel cells (IT-SOFC). Nevertheless, not many materials have been reported to work as cathodes in a LSAO apatite-based cell. In the present work, eight different strontium and cobalt-free compounds with a perovskite-type structure and the general composition LaM1−xNxO3−δ (where M = Fe, Cr, Mn; N = Cu, Ni; and x = 0.2, 0.3) have been tested. This study includes the synthesis and structural characterization of the compounds, as well as thermomechanical and chemical compatibility tests between them. Functional characterization of the individual components has been performed by electrochemical impedance spectroscopy (EIS). Apatite/perovskite symmetrical cells were used to measure area-specific resistance (ASR) of the half cell in an intermediate temperature range (500–850 °C) both with and without DC bias. According to its electrochemical behaviour, LaFe0.8Cu0.2O3−δ is the most promising material for IT-SOFC among the compositions tested since its ASR is similar to that of the traditional (LaxSr1−x)MnO3 (LSM) cathode., This work was financially supported by Spanish Government MAT2015-68078-R (MINECO/FEDER, UE) and RTI2018-098944-J-I00 (MCIU/AEI/FEDER, UE) grants and BES-2016-078508 FPI grant and a flexifund grant under the EPSRC EP/R023662/1 JUICED project, which allowed the author to perform initial experiments at the University of Birmingham under the supervision of Prof. Peter R. Slater. Authors would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cation-driven electrical conductivity in Ta-doped orthorhombic zirconia ceramics

  • Moshtaghioun, Bibi Malmal
  • Laguna-Bercero, M. A.
  • Peña, J. I.
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Arturo
This paper is devoted to the study of the electrical conductivity of tantalum-doped zirconia ceramics prepared by spark plasma sintering. In this study, the temperature dependence of conductivity in as-prepared specimens and in those previously annealed in air is determined and compared. A semi-empirical model, which is based on the oxidation states of the cations, has been developed and successfully assessed. According to this, the conductivity is basically controlled by the diffusion of tetravalent zirconium cations in both cases, although the concentration of these species varies drastically with the amount of induced oxygen vacancies. This is a quite unexpected fact, since conductivity is normally controlled by anionic diffusion in zirconia ceramics. This option is forbidden here due to the presence of substitutional pentavalent cations. Therefore, conductivity values are much lower than those reported in trivalent or divalent substitutional cation doped zirconia ceramics., The authors would like to acknowledge provided by several institutions: BMM wants to acknowledge the Spanish Ministry of Science and Innovation through the grant PID2019-103847RJ-I00, as well as the financial support awarded by the Regional government of the ‘Junta de Andalucía’ through the project P18-RTJ-1972. BMM and JIP gratefully acknowledge the financial support provided the Ministry of Science in Spain through the projects MAT2016-77769-R and Gobierno de Aragón, Spain (Grupo Reconocido DGA T02_17R) and the associated EU Regional Development Funds. MLB acknowledges the funding support provided by the projects MAT2015-68078-R and PID2019-107106RB-C32 funded by the Spanish Ministry of Science and Innovation. Finally, DGG and ADR are grateful to the Spanish Ministry of Science for the research funding through the project MAT2015-71411-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

CO2 and steam electrolysis using a microtubular solid oxide cell

  • Monzón, Hernán
  • Laguna-Bercero, M. A.
Nickel-yttria stabilized zirconia (Ni-YSZ) supported tubes were fabricated by plastic extrusion molding (PEM). YSZ was used as the electrolyte and LSM-YSZ (lanthanum-strontium doped manganite) as the oxygen electrode. Both layers were deposited by dip coating and were then sintered at 1500 °C and 1150 °C, respectively. Coelectrolysis experiments were performed in these cells at 850 °C, using different fuel gas conditions varying the amount of steam, carbon dioxide, nitrogen and hydrogen. Area specific resistance (ASR) values ranged from 0.47 Ωcm2, when rich steam and CO2 flows are used, to 1.74 Ωcm2, when a diluted composition is used. Gas chromatography was used to examine the amount of H2 and CO in the output gas. The obtained results are consistent with the equilibrium of the water gas shift reaction. For all the different analysed conditions, faradaic efficiency was found to be close to 100%. This experiment confirmed that there is no electronic conduction taking place through the YSZ electrolyte. The threshold for electronic conduction in the diluted feeding conditions (Poor H2O and CO2) for these particular YSZ-based cell was found at voltages of about 1.65 V., This work was funded by the MAT2015-68078-R and RTI2018-098944-J-I00 projects, financed by the Spanish Government (Ministerio de Ciencia, Innovación y Universidades) and the Feder Program of the European Union, and also grants GA-LC-035/2012 and LMP154_18 financed by the Aragon Government. The use of Servicio General de Apoyo a la Investigacion-SAI, Universidad de Zaragoza is finally acknowledged for the use of the electron microscopy facilities., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Tailoring the microstructure of a solid oxide fuel cell anode support by calcination and milling of YSZ

  • Hanifi, A.R.
  • Laguna-Bercero, M.
  • Sandhu, N.K.
  • Etsell, T.H.
  • Sarkar, P.
In this study, the effects of calcination and milling of 8YSZ (8 mol% yttria stabilized zirconia) used in the nickel-YSZ anode on the performance of anode supported tubular fuel cells were investigated. For this purpose, two different types of cells were prepared based on a Ni-YSZ/YSZ/Nd2NiO4+d-YSZ configuration. For the anode preparation, a suspension was prepared by mixing NiO and YSZ in a ratio of 65:35 wt% (Ni:YSZ 50:50 vol.%) with 30 vol.% graphite as the pore former. As received Tosoh YSZ or its calcined form (heated at 1500 °C for 3 hours) was used in the anode support as the YSZ source. Electrochemical results showed that optimization of the fuel electrode microstructure is essential for the optimal distribution of gas within the support of the cell, especially under electrolysis operation where the performance for an optimized cell (calcined YSZ) was enhanced by a factor of two. In comparison with a standard cell (containing as received YSZ), at 1.5 V and 800 °C the measured current density was -1380 mA cm-2 and -690 mA cm-2 for the cells containing calcined and as received YSZ, respectively. The present study suggests that the anode porosity for improved cell performance under SOEC is more critical than SOFC mode due to more complex gas diffusion under electrolysis mode where large amount of steam needs to be transfered into the cell.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Range expansion of the Bluetongue vector, Culicoides imicola, in continental France likely due to rare wind-transport events

  • Jacquet, S.
  • Huber, K.
  • Pagès, N.
  • Talavera, S.
  • Burgin, L.E.
  • Carpenter, S.
  • Sanders, C.
  • Dicko, A.H.
  • Djerbal, M.
  • Goffredo, M.
  • Lhor, Y.
  • Lucientes, J.
  • Miranda-Chueca, M.
  • Fonseca, Pereira Da
  • Ramilo, D.W.
  • Setier-Rio, M.
  • Bouyer, J.
  • Chevillon, C.
  • Balenghien, T.
  • Guis, H.
  • Garros, C.
The role of the northward expansion of Culicoides imicola Kieffer in recent and unprecedented outbreaks of Culicoides-borne arboviruses in southern Europe has been a significant point of contention. We combined entomological surveys, movement simulations of air-borne particles, and population genetics to reconstruct the chain of events that led to a newly colonized French area nestled at the northern foot of the Pyrenees. Simulating the movement of air-borne particles evidenced frequent wind-transport events allowing, within at most 36 hours, the immigration of midges from north-eastern Spain and Balearic Islands, and, as rare events, their immigration from Corsica. Completing the puzzle, population genetic analyses discriminated Corsica as the origin of the new population and identified two successive colonization events within west-Mediterranean basin. Our findings are of considerable importance when trying to understand the invasion of new territories by expanding species.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Microtubular solid oxide fuel cells fabricated by gel-casting: the role of supporting microstructure on the mechanical properties

  • Morales, M.
  • Laguna-Bercero, M.A.
Different cell configurations of anode-supported microtubular solid oxide fuel cells (mT-SOFCs) using samaria-doped ceria (SDC) as the electrolyte were fabricated. Several cells were processed varying the porosity and wall thickness (outer diameter) of NiO-SDC tubular supports. Suitable aqueous slurry formulations of NiO-SDC for gel-casting were prepared using agarose, as a gelling agent, and sucrose, as a pore former. The subsequent NiO-SDC anode functional layer (AFL), the SDC electrolyte and the La0.6Sr0.4Co0.2Fe0.8O3-d-SDC cathode were deposited by spray-coating. Afterwards, the electrochemical performance of different single cells was tested under humidified hydrogen as the fuel and air as the oxidant. The mechanical strength of the supporting tubes at different processing stages (green, pre-/post-sintering, post-reduction, post-redox cycle conditions) were also determined to study the macro-mechanical failure behaviour of the cells. In addition, the mechanical strength of half-cells with different porosity, sintering temperature and wall thickness in the tubular supports was also determined. For this purpose, the modulus of rupture was measured by a three point bending test. This study shows that the electrochemical properties and mechanical strength are feasible for further development of anode-supported mT-SOFCs fabricated by gel-casting.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Characterization of laser-processed thin ceramic membranes for electrolyte-supported solid oxide fuel cells

  • Cebollero, J.A.
  • Lahoz, R.
  • Laguna-Bercero, M.A.
  • Peña, J.I.
  • Larrea, A.
  • Orera, V.M.
By laser machining we have prepared thin and self-supported yttria stabilized zirconia (YSZ) electrolytes that can be used in electrolyte-supported solid oxide fuel cells for reducing the operation temperature. The membranes, which are supported by thicker areas of the same material, have an active area of ~20 µm in thickness and up to 8 mm in diameter. Buckling limits the maximum size of the thin areas to below 1 mm, the overall effective active area being formed by multiple thin areas bounded by ribs. Electron Backscattering Diffraction experiments determined that there are not significant strains inside the membranes and that the heat-affected zone is confined to a shallow layer of ~1–2 µm. The bending strength of the membranes decreases by ~26% as a result of the surface microcracking produced by the laser machining. The membranes have a roughness of ~2.5 µm and are coated by a layer of nanoparticles produced by the laser ablation. This coating and small roughness is not detrimental for the cathodic polarization of the cells. Conversely, the cathode polarization resistance decreases ~5% in the 650–850 °C temperature range.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Design and characterization of macroporous alumina membranes for passive samplers of water contaminants

  • Orera, V.M.
  • Silva, J.
  • Franquet-Griell, H.
  • Lacorte, S.
Macroporous ceramic membranes with hierarchical pore structure were developed and characterized for the time-integrated analysis of water contaminants. The alumina membranes were boosted to allow a suitable diffusion rate for envisaged applications. Sacrificial fugitives as cornstarch and graphite and partial sintering technique were utilized for the control of pore structure and morphology. The present study includes: (i) Development of ceramic membrane preparation methods based on wet forming techniques and partial sintering in order to control of membrane parameters such as porosity, tortuosity factor and thickness; (ii) Microstructural characterization of the ceramic membranes using two complementary techniques: Hg-porosimetry and SEM; (iii) the diffusion tests performed under laboratory conditions by an innovative, easy and accurate method based in the use of methylene blue (C16H18ClN3S) water solutions as test compound to study the characteristics of ceramic membranes. Using slip casting and partial sintering processing three different Al2O3 membrane configurations with high values 34.5, 36.9 and 39.6 vol% of interconnected porosity and 1.75, 1.7 and 1.3 mm thickness were prepared. The pore morphology consisted of spherical cavities of 5-10 µm diameter and small pores of 70–200 nm. This study also gathers the basis for the calculation of diffusion coefficients, membrane geometrical factor and sampling rates using methylene blue water solutions whose concentration can be accurately determined by optical absorption measurements at 664 nm. Diffusion coefficients for methylene blue range from 2.3 ± 0.5E-8 to 3.0 ± 0.5E-8 cm2 s-1 increasing as connected porosity increases and membrane thickness decreases. The membrane geometrical factors are low, between 0.6 and 1E-02 and Archie''s constants large 4.5–5.5. This has been associated to the bimodal pore structure with coexistence of large and small pores that may increase the tortuosity factors in membranes. The macroporous ceramic membranes herein developed are suitable for the fabrication of passive samplers aimed at preconcentrating organic contaminants in water.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

The effect of pore-former morphology on the electrochemical performance of solid oxide fuel cells under combined fuel cell and electrolysis modes

  • Laguna-Bercero, M.A.
  • Hanifi, A.R.
  • Menand, L.
  • Sandhu, N.K.
  • Anderson, N.E.
  • Etsell, T.H.
  • Sarkar, P.
The effect of the pore-former used in the Ni-YSZ fuel electrode on the electrochemical performance of solid oxide cells is studied. Three cells with the configuration of Ni-YSZ/YSZ/Nd2NiO4+d-YSZ were fabricated with different pore-formers, such as graphite, PMMA (polymethyl methacrylate) or an equal mixture of both, which were added to the Ni-YSZ support during the fabrication process. The results show that the Ni-YSZ support containing graphite leads to a more porous support and formation of coarser pores in the vicinity of the electrolyte. This leads to a reduction in the triple phase boundary (TPB) length with a corresponding increase of activation polarization and, as a consequence, the overall cell performance decreases in both fuel cell and electrolysis modes. The cell having PMMA delivered the highest performance under both operation modes (818 and -713 mAcm-2 were obtained in SOFC and SOEC modes at 800 °C), due to finer pores next to the electrolyte. The cell having the mixture of both pore-formers delivered intermediate results. All the cells show similar concentration polarization values meaning that even the least porous cell (PMMA) provided sufficient porosity for gas flow. In addition, long term reversible experiments were performed, showing no degradation for a period above 400 h.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Influence of Anode Functional Layers on Electrochemical Performance and Mechanical Strength in Microtubular Solid Oxide Fuel Cells Fabricated by Gel-Casting

  • Morales, M.
  • Laguna-Bercero, M.A.
Anode-supported microtubular solid oxide fuel cells (mT-SOFCs) using samaria-doped ceria (SDC) as electrolyte were fabricated, varying the composition and number of anode functional layers (AFLs), by combining the aqueous gel-casting and spray-coating techniques. Suitable aqueous slurry formulation of NiO-SDC was prepared using agarose as a gelling agent for gel casting of tubular supports. Afterward, 40:60 and 50:50 NiO:SDC (wt %) as AFLs and SDC electrolyte were deposited by spray-coating and subsequently co-sintered. Finally, mT-SOFCs with 2.5 mm outer diameter and thicknesses of 380 pm support; 0, 12, and 24 mu m AFLs; 15 mu m electrolyte; and 30 mu m cathode were obtained. The influence of AFLs on the performance and mechanical integrity was investigated for the three cells. For this purpose, electrochemical and mechanical tests at both macroscopic and micro-/nanometric scales (at the AFLs region) were determined by flexural strength and nanoindentation techniques, respectively. The results evidence that the use of AFLs with an adequate composition and microstructure in the mT-SOFCs is required to improve the performance and mechanical strength of the cell. The cell with a single-layer AFL of 50:50 NiO:SDC (wt %) and 12 pm thickness exhibited the best performance (0.52 W.cm(-2)) at 650 degrees C using hydrogen as fuel and air as oxidant.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

SOFC cathodic layers using wet powder spraying technique with self synthesized nanopowders

  • Wain-Martin, A.
  • Morán-Ruiz, A.
  • Laguna-Bercero, M.A.
  • Campana, R.
  • Larrañaga, A.
  • Slater, P.R.
  • Arriortua, M.I.
In this work, a wet powder spraying method has been investigated as a facile low cost route to deposit electrode layer on SOFC electrolyte support. A particular focus has been examining the interfacial stability of the deposited layers, and determining the influence of the thickness of the different layers, as well as the ball milling regime used to produce the electrode inks. The developed system consist of an yttria stabilized zirconia electrolyte support, a La 0.6 Sr 0.4 FeO 3 (LSF) cathode, a Sm 0.2 Ce 0.8 O 1.9 (SDC) barrier layer between the electrolyte and the cathode, and LaNi 0.6 Fe 0.4 O 3 (LNF) as a contact layer, for a future integration with the SOFC interconnector. The electrolyte supports (300 µm thickness and 9 mm diameter) supports were prepared by uniaxial pressing, while the deposition of thin barrier layers, cathode and contact layer were carried out by manual spray coating.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Optimization of laser-patterned YSZ-LSM composite cathode-electrolyte interfaces for solid oxide fuel cells

  • Cebollero, J.A.
  • Laguna-Bercero, M.A.
  • Lahoz, R.
  • Silva, J.
  • Moreno, R.
  • Larrea, A.
Patterned cathode/electrolyte interfaces formed by a hexagonal array of ~22 µm deep wells with 24 µm lattice parameter have been prepared by pulsed laser machining to enlarge the contact surface and, consequently, to reduce the cathode polarization of Solid Oxide Fuel Cells. These new interfaces have been tested in YSZ-LSM/YSZ/YSZ-LSM symmetrical cells, where the cathode is deposited by dip-coating. Appropriate ceramic suspensions have been formulated to penetrate into deep wells without presenting interfacial delamination after sintering. We analyse their applicability by comparing their rheology with the microstructure and electrochemical performance of the cells. The activation component of the polarization resistance is reduced by ~50% using ethanol-based suspensions with 20 wt% solids loading, although the gas diffusion component increases due to excessive densification. Alternative ceramic suspensions with 17.5 wt% solids loading provide optimum electrode gas diffusion but lower activation components, resulting in an overall decrease of ~20% in polarization resistance.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

CO2 and steam electrolysis using a microtubular solid oxide cell

  • Monzon, H.
  • Laguna-Bercero, M.A.
Nickel-yttria stabilized zirconia (Ni-YSZ) supported tubes were fabricated by plastic extrusion molding (PEM). YSZ was used as the electrolyte and LSM-YSZ (lanthanum-strontium doped manganite) as the oxygen electrode. Both layers were deposited by dip coating and were then sintered at 1500 degrees C and 1150 degrees C, respectively. Coelectrolysis experiments were performed in these cells at 850 degrees C, using different fuel gas conditions varying the amount of steam, carbon dioxide, nitrogen and hydrogen. Area specific resistance (ASR) values ranged from 0.47 Omega cm(2), when rich steam and CO2 flows are used, to 1.74 Omega cm(2), when a diluted composition is used. Gas chromatography was used to examine the amount of H-2 and CO in the output gas. The obtained results are consistent with the equilibrium of the water gas shift reaction. For all the different analysed conditions, faradaic efficiency was found to be close to 100%. This experiment confirmed that there is no electronic conduction taking place through the YSZ electrolyte. The threshold for electronic conduction in the diluted feeding conditions (Poor H2O and CO2) for these particular YSZ-based cell was found at voltages of about 1.65 V.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Suitability of strontium and cobalt-free perovskite cathodes with La9.67Si5AlO26apatite electrolyte for intermediate temperature solid oxide fuel cells

  • Robles-Fernandez, A.
  • Orera, A.
  • Merino, R.I.
  • Slater, P.R.
Aluminium-doped lanthanum silicate (LSAO) apatite-type compounds have been considered as promising candidates for substituting yttria-stabilized zirconia (YSZ) as electrolytes for intermediate temperature solid oxide fuel cells (IT-SOFC). Nevertheless, not many materials have been reported to work as cathodes in a LSAO apatite-based cell. In the present work, eight different strontium andcobalt-free compounds with a perovskite-type structure and the general composition LaM1-xNxO3-d (where M = Fe, Cr, Mn; N = Cu, Ni; and x = 0.2, 0.3) have been tested. This study includes the synthesis and structural characterization of the compounds, as wellas thermomechanical and chemical compatibility tests between them. Functional characterization of the individual components has been performed by electrochemical impedance spectroscopy (EIS). Apatite/perovskite symmetrical cells were used to measure area-specific resistance (ASR) of the half cellin an intermediate temperature range (500-850 °C) both with and without DC bias. According to its electrochemical behaviour, LaFe0.8Cu0.2O3-d is the most promising material for IT-SOFC among the compositions tested since its ASR is similar to that of thetraditional (LaxSr1-x)MnO3 (LSM) cathode.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Development of advanced nickelate-based oxygen electrodes for solid oxide cells

  • Laguna-Bercero, M.
  • Orera, A.
  • Morales-Zapata, M.
  • Larrea, A.
The present work deals with the development of lanthanide nickelate based oxygen electrodes (Ln2NiO4+d, with Ln = Nd, La or Pr) as the oxygen electrode for solid oxide cells (SOCs) operating in both solid oxide fuel cell (SOFC) and solid oxide electrolysis (SOEC) modes. These compounds have been widely investigated as they present high oxygen diffusion properties, making them attractive as SOFC oxygen electrodes. However, the main drawback of these nickelate phases is their reactivity with standard YSZ (yttria stabilized zirconia) or CGO (cerium gadolinium oxide) electrolytes, as typical sintering temperatures are usually higher than 1000 ºC in order to get strong adhesion at the electrode/electrolyte interface. Two strategies will be employed to avoid the undesired reactivity: the direct formation of the nickelate phase into YSZ scaffolds by infiltration and the development of an active barrier layer. © The Electrochemical Society.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Reversible operation performance of microtubular solid oxide cells with a nickelate-based oxygen electrode

  • Morales-Zapata, M.A.
  • Larrea, A.
  • Laguna-Bercero, M.A.
This paper describes the reversible operation of a highly efficient microtubular solid oxide cell (SOC) with a nickelate-based oxygen electrode. The fuel cell was composed of a microtubular support of nickel and yttria stabilized zirconia (Ni-YSZ), an YSZ dense electrolyte, and a double oxygen electrode formed by a first composite layer of praseodymium nickelate (PNO) and gadolinium-doped ceria (CGO) and a second one of PNO. A good performance of the cell was obtained at temperatures up to 800 °C for both fuel cell (SOFC) and electrolysis (SOEC) operation modes, specially promising in electrolysis mode. The current density in SOEC mode at 800 °C is about -980 mA cm-2 at 1.2V with 50% steam. Current density versus voltage curves (j-V) present a linear behavior in the electrolysis mode, with a specific cell area resistance (ASR) of 0.32 O cm-2. Durability experiments were carried out switching the voltage from 0.7V to 1.2V. No apparent degradation was observed in fuel cell mode and SOEC mode up to a period of about 100 h. However, after this period especially in electrolysis mode there is an accumulated degradation associated to nickel coarsening, as confirmed by SEM and EIS experiments. Those results confirm that nickelate based oxygen electrodes are excellent candidates for reversible SOCs. © 2019 Hydrogen Energy Publications LLC