Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Ultrafast Epitaxial Growth Kinetics in Functional Oxide Thin Films Grown by Pulsed Laser Annealing of Chemical Solutions

  • Queraltó López, Albert
  • Pérez del Pino, Ángel|||0000-0002-1405-6027
  • De La Mata, Maria|||0000-0002-1581-4838
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Tristany, Mar
  • Obradors, Xavier|||0000-0003-4592-7718
  • Puig i Molina, Mª Teresa|||0000-0002-1873-0488
The crystallization process and physical properties of different functional oxide thin films (CeZrO, LaNiO, BaSrTiO, and LaSrMnO) on single crystal substrates (YO:ZrO, LaAlO, and SrTiO) are studied by pulsed laser annealing (PLA). A Nd:YAG laser source (λ = 266 nm, 10 Hz and τ ∼3 ns) is employed to crystallize chemical solution deposited (CSD) amorphous/nanocrystalline films under atmospheric conditions. We provide new insight on the influence of photochemical and photothermal interactions on the epitaxial crystallization kinetics of oxide thin films during the transformation from amorphous/polycrystalline material (i.e., atomic diffusion, epitaxial growth rates, and activation energies of nucleation and crystallization). The epitaxial growth is investigated by varying the laser fluence and the applied number of pulses. The morphology, structure, and epitaxial evolution of films are evaluated by means of atomic force and transmission electron microscopies and X-ray diffraction. Highly epitaxial oriented films of 20-40 nm in thickness are obtained by PLA. The crystallization kinetics of laser treatments is determined to be orders of magnitude faster than thermal treatments with similar activation energies (1.5-4.1 eV), mainly due to the large temperature gradients inducing modified atomic diffusion mechanisms derived mainly from photothermal interactions, as well as a minor contribution of photochemical effects. The fast heating rates achieved by PLA also contribute to the fast epitaxial growth due to reduced coarsening of polycrystalline material. The measurement of the physical properties (electrical resistivity and magnetism) of laser processed CSD films has revealed significantly good functionalities, close to those of thermally grown films, but with much shorter processing times.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Ultraviolet pulsed laser crystallization of Ba0.8Sr0.2TiO3 films on LaNiO3-coated silicon substrates

  • Queraltó López, Albert
  • Pérez del Pino, Ángel|||0000-0002-1405-6027
  • De La Mata, Maria|||0000-0002-1581-4838
  • Tristany, Mar
  • Obradors, Xavier|||0000-0003-4592-7718
  • Puig i Molina, Mª Teresa|||0000-0002-1873-0488
  • Trolier-McKinstry, Susan
In this work, BaSrTiO (BST) films on LaNiO-buffered SiO/Si (LNO/SiO/Si) substrates were crystallized by pulsed laser irradiation. Solution-derived amorphous barium-strontium-titanate precursor layers were crystallized with a KrF excimer laser in oxygen ambient at fluences ranging from 50 to 75 mJ cm. With the substrate temperature set to 500 °C, the number of pulses and film thickness were varied until high-quality crystallinity could be achieved. It was found that films with a thickness of 40 nm are fully crystallized with a uniaxial {00l} orientation which is predetermined by the LaNiO orientation. On the other hand, for 160 nm thick films, crystallization was observed after 12,000 pulses in the 70 nm close to the surface, while the rest of the film remained amorphous. The large temperature difference between the film surface and interface due to the low thermal conductivity of the amorphous BST is suggested as the origin of this behavior. Films thicker than 80 nm cracked on crystallization due to the stress caused by the different thermal expansion coefficients of film and substrate, as well as the large temperature variations within the BST film.