Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Biodegradable porous FeMn(-xAg) alloys, assessment of cytocompatibility, mechanical, magnetic and antibiofilm properties

  • Bartkowska, Aleksandra|||0000-0002-6133-7155
  • Careta, Oriol|||0000-0003-1333-0300
  • Turner, Adam Benedict|||0000-0002-4485-6738
  • Blanquer, Andreu|||0000-0002-3551-1885
  • Ibáñez, Elena|||0000-0002-0275-6958
  • Trobos, Margarita|||0000-0002-9253-6771
  • Nogués, Carme|||0000-0002-6361-8559
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
In this work, porous FeMn(-xAg) alloys are fabricated through powder metallurgy methods. The effects of porosity and Ag addition on the microstructure, biodegradability, magnetic and mechanical properties of the alloys are investigated. Studies on the cytocompatibility, inflammatory cytokine response and antibacterial effect are also conducted. The fabricated alloys exhibit a macro- and nanoporous structure, with uniformly distributed silver particles. The biodegradability tests reveal that the release of Mn to the Hank's solution is higher than that of Fe, without significant differences between the alloys. The degradation products consist mainly of Fe, Mn, O and compounds enriched in Ca, P and Cl. As-sintered alloys show a low saturation magnetization value (below 1 emu g-1), which does not increase significantly with immersion time. The results on biocompatibility indicate that all tested alloys are non-cytotoxic, but the addition of Ag might interfere with cell proliferation. However, the ions released by the FeMn(-xAg) alloys do not induce an inflammatory response in macrophages. The obtained results on microbiological interactions reveal that although no significant bactericidal effect is observed at 4 h between FeMn control and FeMn-5Ag, a significant reduction in the total biofilm biomass of both live and dead bacteria is observed after 24 h in Ag containing FeMn-5Ag surfaces.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Motion analysis and real-time trajectory prediction of magnetically steerable catalytic Janus micromotors

  • Wu, Jiaen|||0000-0001-5020-873X
  • Folio, David|||0000-0001-9430-6091
  • Zhu, Jiawei
  • Jang, Bumjin
  • Chen, Xiangzhong|||0000-0002-2294-7487
  • Feng, Junxiao
  • Gambardella, Pietro|||0000-0003-0031-9217
  • Sort, Jordi|||0000-0003-1213-3639
  • Puigmarti-Luis, Josep|||0000-0002-7510-9815
  • Ergeneman, Olgaç
  • Ferreira, Antoine
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
Chemically driven micromotors display unpredictable trajectories due to the rotational Brownian motion interacting with the surrounding fluid molecules. This hampers the practical applications of these tiny robots, particularly where precise control is a requisite. To overcome the rotational Brownian motion and increase motion directionality, robots are often decorated with a magnetic composition and guided by an external magnetic field. However, despite the straightforward method, explicit analysis and modeling of their motion have been limited. Here, catalytic Janus micromotors are fabricated with distinct magnetizations and a controlled self-propelled motion with magnetic steering is shown. To analyze their dynamic behavior, a dynamic model that can successfully predict the trajectory of micromotors in uniform viscous flows in real time by incorporating a form of state-dependent-coefficient with a robust two-stage Kalman filter is theoretically developed. A good agreement is observed between the theoretically predicted dynamics and experimental observations over a wide range of model parameter variations. The developed model can be universally adopted to various designs of catalytic micro-/nanomotors with different sizes, geometries, and materials, even in diverse fuel solutions. Finally, the proposed model can be used as a platform for biosensing, detecting fuel concentration, or determining small-scale motors' propulsion mechanisms in an unknown environment.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Fabrication of hybrid nanocrystalline Al-Ti alloys by mechanical bonding through high-pressure torsion

  • Bazarnik, Piotr|||0000-0002-6329-6983
  • Bartkowska, Aleksandra|||0000-0002-6133-7155
  • Huang, Yi
  • Szlązak, Karol
  • Adamczyk-Cieślak, Bogusława|||0000-0002-1209-0256
  • Sort, Jordi|||0000-0003-1213-3639
  • Lewandowska, Malgorzata|||0000-0002-5399-4008
  • Langdon, Terence G.
This study demonstrates an approach of utilizing high-pressure torsion (HPT) to fabricate a novel hybrid material by the direct bonding of Al and Ti disks at room temperature under a compressive pressure of 6.0 GPa and with increasing numbers of HPT turns up to 50. Detailed structural observations revealed the formation of a multi-layered nanostructure in the edge regions of the disks with a grain size of ∼30 nm. X-ray diffraction (XRD) and selected area electron diffraction (SAED) confirmed the presence of three intermetallic compounds, AlTi, Al3Ti and Ti3Al, in the layered structures. Processing by HPT led to the formation of a hybrid nanocomposite with exceptional hardness (over 300 Hv) in the edge regions of the disks. Special emphasis was placed on understanding the evolution of hardness in the hybrid material. The investigation demonstrates a significant opportunity for using HPT processing to deepen the knowledge on diffusion bonding and mechanical joining technologies as well as for fabricating new and valuable hybrid nanomaterials.