Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Standard penetration testing in a virtual calibration chamber

  • Zhang, Ningning
  • Arroyo Álvarez de Toledo, Marcos|||0000-0001-9384-9107
  • Ciantia, Matteo Oryem|||0000-0003-1897-4471
  • Gens Solé, Antonio|||0000-0001-7588-7054
  • Butlanska, Joanna
The virtual calibration chamber technique, based on the discrete element method, is here applied to study the standard penetration test (SPT). A macro-element approach is used to represent a rod driven with an impact like those applied to perform SPT. The rod is driven into a chamber filled with a scaled discrete analogue of a quartz sand. The contact properties of the discrete analogue are calibrated simulating two low-pressure triaxial tests. The rod is driven changing input energy and controlling initial density and confinement stress. Energy-based blowcount normalization is shown to be effective. Results obtained are in good quantitative agreement with well-accepted experimentally-based relations between blowcount, density and overburden. It is also shown that the tip resistance measured under impact dynamic penetration conditions is close to that under constant velocity conditions, hence supporting recent proposals to relate CPT and SPT results., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Grading evolution and critical state in a discrete numerical model of Fontainebleau sand

  • Ciantia, Matteo Oryem|||0000-0003-1897-4471
  • Arroyo Álvarez de Toledo, Marcos|||0000-0001-9384-9107
  • O'Sullivan, Catherine
  • Gens Solé, Antonio|||0000-0001-7588-7054
  • Liu, T.
Granular materials reach critical states upon shearing. The position and shape of a critical state line (CSL) in the compression plane are important for constitutive models, interpretation of in situ tests and liquefaction analyses. It is not fully clear how grain crushing may affect the identification and uniqueness of the CSL in granular soils. Discrete-element simulations are used here to establish the relation between breakage-induced grading evolution and the CSL position in the compression plane. An efficient model of particle breakage is applied to perform a large number of tests, in which grading evolution is continuously tracked using a grading index. Using both previous and new experimental results, the discrete-element model is calibrated and validated to represent Fontainebleau sand, a quartz sand. The results obtained show that, when breakage is present, the inclusion of a grading index in the description of critical states is advantageous. This can be simply done using the critical state plane (CSP) concept. A CSP is obtained for Fontainebleau sand., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Thermal effects in landslide mobility

  • Pinyol Puigmartí, Núria Mercè|||0000-0002-1878-1365
  • Alvarado Bueno, Mauricio
  • Alonso Pérez de Agreda, Eduardo|||0000-0003-2472-3951
  • Zabala, Francisco
2019 Telfor Medal, concedida per la Institution of Civil Engineers (ICE), The paper describes a thermo-hydro-mechanical formulation to model thermal-induced effects due to the irreversible work input generated during the soil deformation. The model was implemented into a Material Point calculation procedure. The method is applied to the analysis of landslides. A simple slope stability is first analysed. Mechanical work essentially dissipates in shearing bands which develop excess pore water pressures. The marked effect of soil permeability to control the slide motion after failure is described. Shear band thickness is also a relevant control variable. The problem posed by the non-realistic thickness of shear bands in numerical calculation is addressed by means of a numerical procedure that includes the consideration of embedded shear bands where the strains are assumed to be localized. Balance equations describing local flow and thermal interactions between shear bands and the remaining material are formulated. The method is applied to model the instability and subsequent rapid motion of Vajont landslide. Calculated run-out and sliding velocity reproduce, in a satisfactory manner, field observations., Peer Reviewed, Award-winning
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

DEM modelling of dynamic penetration in granular material

  • Zhang, Ming
  • Arroyo Álvarez de Toledo, Marcos|||0000-0001-9384-9107
  • Gens Solé, Antonio|||0000-0001-7588-7054
  • Ciantia, Matteo Oryem|||0000-0003-1897-4471
Dynamic penetration has been widely employed in some site investigation procedures and for the installation of driven piles. A 3-dimensional discrete element method model has been developed to simulate dynamic rod penetration into a calibration chamber. The chamber has been filled with a scaled analogue of Fontainebleau sand. A novel method for simulating the physical rod as boundary condition is presented. It is shown that the method leads to a good agreement in static penetration comparisons. A parametric study of involved variables shows that penetration increases with force magnitude and impact time but tip resistance is quite insensitive to them. The tests are then extended to six conditions that combine two density levels and three confining stresses. It is found that increasing the confining stress does increase tip resistance, whereas it reduces penetration distance. As expected, penetration in dense sand results in larger penetration resistances and smaller penetration distances.
UPCommons. Portal del coneixement obert de la UPC
Publicación Capítulo o parte de un libro (BookPart)

Discrete element models of soil-geogrid interaction

  • Irsainova, Alina
  • Arroyo Álvarez de Toledo, Marcos|||0000-0001-9384-9107
  • Kim, Jong-Ryeol
Geogrids are the geosynthetics of choice for soil reinforcement applications. To evaluate the efficiency of geogrid reinforcement, several methods are used including field tests, laboratory tests and numerical modeling. Field studies consume long period of time and conducting these investigations may become highly expensive because of the need for real-size structures. Laboratory studies present also significant difficulties: large-size testing machines are required to accommodate realistic geogrid designs. The discrete element method (DEM) may be used as a complementary tool to extend physical testing databases at lower cost. Discrete element models do not require complex constitutive formulations and may be fed with particle scale data (size, strength, shape) thus reducing the number offree calibration parameters. Discrete element models also are well suited to problems in which large displacements are present, such as geogrid pullout. This paper reviews the different approaches followed to model soil-geogrid interaction in DEM and presents preliminary results from pull-out conditions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Marchetti flat dilatometer tests in a virtual calibration chamber

  • Butlanska, Joanna
  • Arroyo Álvarez de Toledo, Marcos|||0000-0001-9384-9107
  • Amoroso, Sara
  • Gens Solé, Antonio|||0000-0001-7588-7054
Copyright ASTM International. All rights reserved, 2018/16/07. Downloaded by UPC, pursuant to Author/Copyright Owner Agreement. No further reproduction authorized., Calibration chambers are frequently used to verify, adapt, or both verify and adapt empirical relations between different state variables and in situ test results. Virtual calibration chambers (VCC) built with 3D discrete element models may be used to extend and partially substitute costly physical testing series. VCC are used here to explore the mechanics of flat dilatometer penetration and expansion. Results obtained for a simulation of physical tests in Ticino sand are presented. Blade tip resistance during penetration is in good agreement with the experiments. A piston-like design is used for the blade so that larger displacements may be applied than it is possible with a membrane. Initial piston pressures in the expansion curves are very low, strongly affected by the scaled-up grain sizes. Despite that difficulty, expansion curves may be easily interpreted to recover dilatometer moduli ED close to those observed in the physical experiments. Particle-scale examination of the results allows a firmer understanding of the current limitations and future potential of the technique., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Micromechanical inspection of incremental behaviour of crushable soils

  • Ciantia, Matteo Oryem|||0000-0003-1897-4471
  • Arroyo Álvarez de Toledo, Marcos|||0000-0001-9384-9107
  • O'Sullivan, Catherine
  • Gens Solé, Antonio|||0000-0001-7588-7054
In granular soils grain crushing reduces dilatancy and stress obliquity enhances crushability. These are well-supported specimen-scale experimental observations. In principle, those observations should reflect some peculiar micromechanism associated with crushing, but which is it? To answer that question the nature of crushing-induced particle-scale interactions is here investigated using an efficient DEM model of crushable soil. Microstructural measures such as the mechanical coordination number and fabric are examined while performing systematic stress probing on the triaxial plane. Numerical techniques such as parallel and the newly introduced sequential probing enable clear separation of the micromechanical mechanisms associated with crushing. Particle crushing is shown to reduce fabric anisotropy during incremental loading and to slow fabric change during continuous shearing. On the other hand, increased fabric anisotropy does take more particles closer to breakage. Shear-enhanced breakage appears then to be a natural consequence of shear-enhanced fabric anisotropy. The particle crushing model employed here makes crushing dependent only on particle and contact properties, without any pre-established influence of particle connectivity. That influence does not emerge, and it is shown how particle connectivity, per se, is not a good indicator of crushing likelihood., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Coupled effective stress analysis of insertion problems in geotechnics with the Particle Finite Element Method

  • Monforte Vila, Lluís
  • Arroyo Álvarez de Toledo, Marcos|||0000-0001-9384-9107
  • Carbonell Puigbó, Josep Maria|||0000-0002-2378-5053
  • Gens Solé, Antonio|||0000-0001-7588-7054
This paper describes a computational framework for the numerical analysis of quasi-static soil-structure insertion problems in water saturated media. The Particle Finite Element Method is used to solve the linear momentum and mass balance equations at large strains. Solid-fluid interaction is described by a simplified Biot formulation using pore pressure and skeleton displacements as basic field variables. The robustness and accuracy of the proposal is numerically demonstrated presenting results from two benchmark examples. The first one addresses the consolidation of a circular footing on a poroelastic soil. The second one is a parametric analysis of the cone penetration test (CPTu) in a material described by a Cam-clay hyperelastic model, in which the influence of permeability and contact roughness on test results is assessed., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

DEM simulation of soil-tool interaction under extraterrestrial environmental effects

  • Jiang, Mingjing
  • Xi, Banglu
  • Arroyo Álvarez de Toledo, Marcos|||0000-0001-9384-9107
  • Rodríguez Dono, Alfonso|||0000-0002-2296-4826
In contrast to terrestrial environment, the harsh lunar environment conditions include lower gravity acceleration, ultra-high vacuum and high (low) temperature in the daytime (night-time). This paper focuses on the effects of those mentioned features on soil cutting tests, a simplified excavation test, to reduce the risk of lunar excavation missions. Soil behavior and blade performance were analyzed under different environmental conditions. The results show that: (1) the cutting resistance and the energy consumption increase linearly with the gravity. The bending moment has a bigger increasing rate in low gravity fields due to a decreasing moment arm; (2) the cutting resistance, energy consumption and bending moment increase significantly because of the raised soil strength on the lunar environment, especially in low gravity fields. Under the lunar environment, the proportions of cutting resistance, bending moment and energy consumption due to the effect of the van der Waals forces are significant. Thus, they should be taken into consideration when planning excavations on the Moon. Therefore, considering that the maximum frictional force between the excavator and the lunar surface is proportional to the gravity acceleration, the same excavator that works efficiently on the Earth may not be able to work properly on the Moon., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Image-based calibration of rolling resistance in discrete element models of sand

  • Rorato, Riccardo
  • Arroyo Álvarez de Toledo, Marcos|||0000-0001-9384-9107
  • Gens Solé, Antonio|||0000-0001-7588-7054
  • Andò, Edward
  • Viggiani, Gioacchino
Models that introduce rolling resistance at the contact are widely employed in simulations using the discrete element method (DEM) to indirectly represent particle shape effects. This approach offers substantial computational benefits at the price of increased calibration complexity. This work proposes a method to simplify calibration of rolling resistance. The key element is an empirical relation between a contact parameter (rolling friction) and a 3D grain shape descriptor (true sphericity). Values of true sphericity can be obtained by image analysis of the grains, either directly by 3D acquisition or by correlation with simpler-to-obtain 2D shape measures. Evaluation of rolling friction is thus made independent from that of other model parameters. As an extra benefit, the variability of grain shape in natural sands can be directly mapped into the discrete model. A mapping between rolling friction and true sphericity is calibrated using specimen-scale and grain scale results from two triaxial compression tests on Hostun sand and Caicos ooids. The mapping is validated using different triaxial tests from the same sands and from other reference sands (Ottawa, Ticino). In the case of Ticino grain-shape acquisition is made in 2D, using an ordinary table scanner. The results obtained support this direct calibration procedure., The support of EU through 645665 - GEO-RAMP - MSCA-RISE and of the Ministry of Economy of Spain through research Grant BIA2014-59467-R is gratefully acknowledged. Laboratoire 3SR is part of the LabEx Tec 21 (Investissements d’Avenir - grant agreement n_ANR-11-LABX-0030)., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Micromechanical inspection of incremental behaviour of crushable soils

  • Ciantia, Matteo Oryem
  • Arroyo Álvarez de Toledo, Marcos
  • O'Sullivan, Catherine
  • Gens Solé, Antonio
In granular soils grain crushing reduces dilatancy and stress obliquity enhances crushability. These are well-supported specimen-scale experimental observations. In principle, those observations should reflect some peculiar micromechanism associated with crushing, but which is it? To answer that question the nature of crushing-induced particle-scale interactions is here investigated using an efficient DEM model of crushable soil. Microstructural measures such as the mechanical coordination number and fabric are examined while performing systematic stress probing on the triaxial plane. Numerical techniques such as parallel and the newly introduced sequential probing enable clear separation of the micromechanical mechanisms associated with crushing. Particle crushing is shown to reduce fabric anisotropy during incremental loading and to slow fabric change during continuous shearing. On the other hand, increased fabric anisotropy does take more particles closer to breakage. Shear-enhanced breakage appears then to be a natural consequence of shear-enhanced fabric anisotropy. The particle crushing model employed here makes crushing dependent only on particle and contact properties, without any pre-established influence of particle connectivity. That influence does not emerge, and it is shown how particle connectivity, per se, is not a good indicator of crushing likelihood., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Image-based calibration of rolling resistance in discrete element models of sand

  • Rorato, Riccardo
  • Arroyo Álvarez de Toledo, Marcos
  • Gens Solé, Antonio
  • Andò, Edward
  • Viggiani, Gioacchino
Models that introduce rolling resistance at the contact are widely employed in simulations using the discrete element method (DEM) to indirectly represent particle shape effects. This approach offers substantial computational benefits at the price of increased calibration complexity. This work proposes a method to simplify calibration of rolling resistance. The key element is an empirical relation between a contact parameter (rolling friction) and a 3D grain shape descriptor (true sphericity). Values of true sphericity can be obtained by image analysis of the grains, either directly by 3D acquisition or by correlation with simpler-to-obtain 2D shape measures. Evaluation of rolling friction is thus made independent from that of other model parameters. As an extra benefit, the variability of grain shape in natural sands can be directly mapped into the discrete model. A mapping between rolling friction and true sphericity is calibrated using specimen-scale and grain scale results from two triaxial compression tests on Hostun sand and Caicos ooids. The mapping is validated using different triaxial tests from the same sands and from other reference sands (Ottawa, Ticino). In the case of Ticino grain-shape acquisition is made in 2D, using an ordinary table scanner. The results obtained support this direct calibration procedure., The support of EU through 645665 - GEO-RAMP - MSCA-RISE and of the Ministry of Economy of Spain through research Grant BIA2014-59467-R is gratefully acknowledged. Laboratoire 3SR is part of the LabEx Tec 21 (Investissements d’Avenir - grant agreement n_ANR-11-LABX-0030)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación

Discrete element models of soil-geogrid interaction

  • Irsainova, Alina
  • Arroyo Álvarez de Toledo, Marcos
  • Kim, Jong-Ryeol
Geogrids are the geosynthetics of choice for soil reinforcement applications. To evaluate the efficiency of geogrid reinforcement, several methods are used including field tests, laboratory tests and numerical modeling. Field studies consume long period of time and conducting these investigations may become highly expensive because of the need for real-size structures. Laboratory studies present also significant difficulties: large-size testing machines are required to accommodate realistic geogrid designs. The discrete element method (DEM) may be used as a complementary tool to extend physical testing databases at lower cost. Discrete element models do not require complex constitutive formulations and may be fed with particle scale data (size, strength, shape) thus reducing the number offree calibration parameters. Discrete element models also are well suited to problems in which large displacements are present, such as geogrid pullout. This paper reviews the different approaches followed to model soil-geogrid interaction in DEM and presents preliminary results from pull-out conditions., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal effects in landslide mobility

  • Pinyol Puigmartí, Núria Mercè
  • Alvarado Bueno, Mauricio
  • Alonso Pérez de Agreda, Eduardo
  • Zabala, Francisco
2019 Telfor Medal, concedida per la Institution of Civil Engineers (ICE), The paper describes a thermo-hydro-mechanical formulation to model thermal-induced effects due to the irreversible work input generated during the soil deformation. The model was implemented into a Material Point calculation procedure. The method is applied to the analysis of landslides. A simple slope stability is first analysed. Mechanical work essentially dissipates in shearing bands which develop excess pore water pressures. The marked effect of soil permeability to control the slide motion after failure is described. Shear band thickness is also a relevant control variable. The problem posed by the non-realistic thickness of shear bands in numerical calculation is addressed by means of a numerical procedure that includes the consideration of embedded shear bands where the strains are assumed to be localized. Balance equations describing local flow and thermal interactions between shear bands and the remaining material are formulated. The method is applied to model the instability and subsequent rapid motion of Vajont landslide. Calculated run-out and sliding velocity reproduce, in a satisfactory manner, field observations., Peer Reviewed, Award-winning, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Standard penetration testing in a virtual calibration chamber

  • Zhang, Ningning
  • Arroyo Álvarez de Toledo, Marcos
  • Ciantia, Matteo Oryem
  • Gens Solé, Antonio
  • Butlanska, Joanna
The virtual calibration chamber technique, based on the discrete element method, is here applied to study the standard penetration test (SPT). A macro-element approach is used to represent a rod driven with an impact like those applied to perform SPT. The rod is driven into a chamber filled with a scaled discrete analogue of a quartz sand. The contact properties of the discrete analogue are calibrated simulating two low-pressure triaxial tests. The rod is driven changing input energy and controlling initial density and confinement stress. Energy-based blowcount normalization is shown to be effective. Results obtained are in good quantitative agreement with well-accepted experimentally-based relations between blowcount, density and overburden. It is also shown that the tip resistance measured under impact dynamic penetration conditions is close to that under constant velocity conditions, hence supporting recent proposals to relate CPT and SPT results., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

DEM modelling of dynamic penetration in granular material

  • Zhang, Ming
  • Arroyo Álvarez de Toledo, Marcos
  • Gens Solé, Antonio
  • Ciantia, Matteo Oryem
Dynamic penetration has been widely employed in some site investigation procedures and for the installation of driven piles. A 3-dimensional discrete element method model has been developed to simulate dynamic rod penetration into a calibration chamber. The chamber has been filled with a scaled analogue of Fontainebleau sand. A novel method for simulating the physical rod as boundary condition is presented. It is shown that the method leads to a good agreement in static penetration comparisons. A parametric study of involved variables shows that penetration increases with force magnitude and impact time but tip resistance is quite insensitive to them. The tests are then extended to six conditions that combine two density levels and three confining stresses. It is found that increasing the confining stress does increase tip resistance, whereas it reduces penetration distance. As expected, penetration in dense sand results in larger penetration resistances and smaller penetration distances., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

DEM simulation of soil-tool interaction under extraterrestrial environmental effects

  • Jiang, Mingjing
  • Xi, Banglu
  • Arroyo Álvarez de Toledo, Marcos
  • Rodríguez Dono, Alfonso
In contrast to terrestrial environment, the harsh lunar environment conditions include lower gravity acceleration, ultra-high vacuum and high (low) temperature in the daytime (night-time). This paper focuses on the effects of those mentioned features on soil cutting tests, a simplified excavation test, to reduce the risk of lunar excavation missions. Soil behavior and blade performance were analyzed under different environmental conditions. The results show that: (1) the cutting resistance and the energy consumption increase linearly with the gravity. The bending moment has a bigger increasing rate in low gravity fields due to a decreasing moment arm; (2) the cutting resistance, energy consumption and bending moment increase significantly because of the raised soil strength on the lunar environment, especially in low gravity fields. Under the lunar environment, the proportions of cutting resistance, bending moment and energy consumption due to the effect of the van der Waals forces are significant. Thus, they should be taken into consideration when planning excavations on the Moon. Therefore, considering that the maximum frictional force between the excavator and the lunar surface is proportional to the gravity acceleration, the same excavator that works efficiently on the Earth may not be able to work properly on the Moon., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Coupled effective stress analysis of insertion problems in geotechnics with the Particle Finite Element Method

  • Monforte Vila, Lluís
  • Arroyo Álvarez de Toledo, Marcos
  • Carbonell Puigbó, Josep Maria
  • Gens Solé, Antonio
This paper describes a computational framework for the numerical analysis of quasi-static soil-structure insertion problems in water saturated media. The Particle Finite Element Method is used to solve the linear momentum and mass balance equations at large strains. Solid-fluid interaction is described by a simplified Biot formulation using pore pressure and skeleton displacements as basic field variables. The robustness and accuracy of the proposal is numerically demonstrated presenting results from two benchmark examples. The first one addresses the consolidation of a circular footing on a poroelastic soil. The second one is a parametric analysis of the cone penetration test (CPTu) in a material described by a Cam-clay hyperelastic model, in which the influence of permeability and contact roughness on test results is assessed., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Grading evolution and critical state in a discrete numerical model of Fontainebleau sand

  • Ciantia, Matteo Oryem
  • Arroyo Álvarez de Toledo, Marcos
  • O'Sullivan, Catherine
  • Gens Solé, Antonio
  • Liu, T.
Granular materials reach critical states upon shearing. The position and shape of a critical state line (CSL) in the compression plane are important for constitutive models, interpretation of in situ tests and liquefaction analyses. It is not fully clear how grain crushing may affect the identification and uniqueness of the CSL in granular soils. Discrete-element simulations are used here to establish the relation between breakage-induced grading evolution and the CSL position in the compression plane. An efficient model of particle breakage is applied to perform a large number of tests, in which grading evolution is continuously tracked using a grading index. Using both previous and new experimental results, the discrete-element model is calibrated and validated to represent Fontainebleau sand, a quartz sand. The results obtained show that, when breakage is present, the inclusion of a grading index in the description of critical states is advantageous. This can be simply done using the critical state plane (CSP) concept. A CSP is obtained for Fontainebleau sand., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Marchetti flat dilatometer tests in a virtual calibration chamber

  • Butlanska, Joanna
  • Arroyo Álvarez de Toledo, Marcos
  • Amoroso, Sara
  • Gens Solé, Antonio
Copyright ASTM International. All rights reserved, 2018/16/07. Downloaded by UPC, pursuant to Author/Copyright Owner Agreement. No further reproduction authorized., Calibration chambers are frequently used to verify, adapt, or both verify and adapt empirical relations between different state variables and in situ test results. Virtual calibration chambers (VCC) built with 3D discrete element models may be used to extend and partially substitute costly physical testing series. VCC are used here to explore the mechanics of flat dilatometer penetration and expansion. Results obtained for a simulation of physical tests in Ticino sand are presented. Blade tip resistance during penetration is in good agreement with the experiments. A piston-like design is used for the blade so that larger displacements may be applied than it is possible with a membrane. Initial piston pressures in the expansion curves are very low, strongly affected by the scaled-up grain sizes. Despite that difficulty, expansion curves may be easily interpreted to recover dilatometer moduli ED close to those observed in the physical experiments. Particle-scale examination of the results allows a firmer understanding of the current limitations and future potential of the technique., Peer Reviewed, Postprint (published version)