Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

Time-resolved imaging techniques applied to femtosecond laser material processing

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Femtosecond laser-controlled self-assembly of amorphous-crystalline nanogratings in silicon

  • Puerto, D.
  • García-Lechuga, Mario
  • Hernández Rueda, Javier
  • García-Leis, Adianez
  • Sánchez-Cortés, Santiago
  • Solís Céspedes, Javier
  • Siegel, Jan
8 págs.; 5 figs.; 1 tab., Self-assembly (SA) of molecular units to form regular, periodic extended structures is a powerful bottom-up technique for nanopatterning, inspired by nature. SA can be triggered in all classes of solid materials, for instance, by femtosecond laser pulses leading to the formation of laser-induced periodic surface structures (LIPSS) with a period slightly shorter than the laser wavelength. This approach, though, typically involves considerable material ablation, which leads to an unwanted increase of the surface roughness. We present a new strategy to fabricate high-precision nanograting structures in silicon, consisting of alternating amorphous and crystalline lines, with almost no material removal. The strategy can be applied to static irradiation experiments and can be extended into one and two dimensions by scanning the laser beam over the sample surface. We demonstrate that lines and areas with parallel nanofringe patterns can be written by an adequate choice of spot size, repetition rate and scan velocity, keeping a constant effective pulse number (N ) per area for a given laser wavelength. A deviation from this pulse number leads either to inhomogeneous or ablative structures. Furthermore, we demonstrate that this approach can be used with different laser systems having widely different wavelengths (1030 nm, 800 nm, 400 nm), pulse durations (370 fs, 100 fs) and repetition rates (500 kHz, 100 Hz, single pulse) and that the grating period can also be tuned by changing the angle of laser beam incidence. The grating structures can be erased by irradiation with a single nanosecond laser pulse, triggering recrystallization of the amorphous stripes. Given the large differences in electrical conductivity between the two phases, our structures could find new applications in nanoelectronics., This work has been supported by the LiNaBioFluid project of the H2020 program of the European Commission (FETOPEN- 665337) as well as by the Spanish TEC2014-52642-C2- 1-R. MG-L and JH-R acknowledge the grants respectively awarded by the Spanish Ministry of Education and the Spanish Ministry of Economy and Competiveness., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrafast Moving-Spot Microscopy: Birth and Growth of Laser-Induced Periodic Surface Structures

  • García-Lechuga, Mario
  • Puerto, D.
  • Fuentes-Edfuf, Yasser
  • Solís Céspedes, Javier
  • Siegel, Jan
7 págs.; 5 figs., Laser-induced periodic surface structures (LIPSS) are a universal phenomenon observed in all classes of solid materials, giving rise to a variety of self-assembled subwavelength structures with different symmetries. These promising features have opened new opportunities for laser structuring of materials in a wide range of applications, including plasmonics, nanophotonics, nanoelectronics, sensing, and even mechanics. However, there is an ongoing debate about the formation mechanism of LIPSS, and the current picture stems mainly from the combined effort of theoretical modeling and experimental studies of the final structures produced. Here we demonstrate femtosecond-resolved imaging of the formation process of such structures produced by ultrashort laser pulses in silicon. The particular type of LIPSS studied are well-aligned amorphous-crystalline fringes generated in dynamic processing conditions, whose period can be tuned and which can be extended over large areas. Using a moving-spot, multiple-pulse irradiation approach we are able to spatially and temporally resolve the birth and growth of individual fringes. We demonstrate that the formation process is initiated by free electron generation leading to nonthermal melting, liquid phase overheating, and rapid solidification into the amorphous phase. © 2016 American Chemical Society, This work has been supported by the LiNaBioFluid project (H2020-FETOPEN-2014-2015RIA, grant 665337) of the European Commission as well as by the Spanish Ministry of Economy and Competiveness through research grant TEC2014-52642-C2-1-R and an FPU fellowship for M.G.-L from the Spanish Ministry of Education, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Three‐Dimensional self‐organization in nanocomposite layered systems by ultrafast laser pulses

  • Liu, Z.
  • Siegel, Jan
  • García-Lechuga, Mario
  • Epicier, T.
  • Lefkir, Y.
  • Reynaud, S.
  • Bugnet, M.
  • Vocanson, F.
  • Solís Céspedes, Javier
  • Vitrant, G.
  • Destouches, N.
10 pags., 6 figs., Controlling plasmonic systems with nanometer resolution in transparent films and their colors over large nonplanar areas is a key issue for spreading their use in various industrial fields. Using light to direct self-organization mechanisms provides high-speed and flexible processes to meet this challenge. Here, we describe a route for the laser-induced self-organization of metallic nanostructures in 3D. Going beyond the production of planar nanopatterns, we demonstrate that ultrafast laser-induced excitation combined with nonlinear feedback mechanisms in a nanocomposite thin film can lead to 3D self-organized nanostructured films. The process, which can be extended to complex layered composite systems, produces highly uniform large-area nanopatterns. We show that 3D self-organization originates from the simultaneous excitation of independent optical modes at different depths in the film and is activated by the plasmon-induced charge separation and thermally induced NP growth mechanisms. This laser color marking technique enables multiplexed optical image encoding and the generated nanostructured Ag NPs:TiO2 films offer great promise for applications in solar energy harvesting, photocatalysis, or photochromic devices., This work was funded by the French Research Agency (ANR) in the framework of project PHOTOFLEX 12-NANO-0006 and programs ANR-10-LABX-0075 (Labex MANUTECHSISE) and ANR-11-IDEX-0007. It has also been supported by the LiNaBioFluid project (H2020-FETOPEN-2014- 2015RIA, grant 665337) of the European Commission, as well as by a research grant (TEC2014-52642-C2-1-R) from the Spanish Ministry of Economy and Competitiveness. M.G.-L. thanks the Spanish Ministry of Education for a FPU fellowship. The authors thank CLYM (www.clym.fr) for access to the Jeol 2010F TEM and the FEI Titan ETEM G2 80-300. GIE MANUTECH-USD is acknowledged for providing access to the FEI Dual Beam Helios600i., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fabrication of amorphous micro-ring arrays in crystalline silicon using ultrashort laser pulses

  • Fuentes-Edfuf, Yasser
  • García-Lechuga, Mario
  • Puerto, D.
  • Florian, Camilo
  • García-Leis, Adianez
  • Sánchez-Cortés, Santiago
  • Solís Céspedes, Javier
  • Siegel, Jan
5 pags., 4 figs., We demonstrate a simple way to fabricate amorphous micro-rings in crystalline silicon using direct laser writing. This method is based on the fact that the phase of a thin surface layer can be changed into the amorphous phase by irradiation with a few ultrashort laser pulses (800 nm wavelength and 100 fs duration). Surface-depressed amorphous rings with a central crystalline disk can be fabricated without the need for beam shaping, featuring attractive optical, topographical, and electrical properties. The underlying formation mechanism and phase change pathway have been investigated by means of fs-resolved microscopy, identifying fluence-dependent melting and solidification dynamics of the material as the responsible mechanism. We demonstrate that the lateral dimensions of the rings can be scaled and that the rings can be stitched together, forming extended arrays of structures not limited to annular shapes. This technique and the resulting structures may find applications in a variety of fields such as optics, nanoelectronics, and mechatronics. Published by AIP Publishing., This work has been supported by the LiNaBioFluid Project (H2020-FETOPEN-2014–2015RIA, Grant No. 665337) of the European Commission as well as the research grant (TEC2014–52642-C2–1-R) from the Spanish Ministry of Economy and Competitiveness. M.G.-L. thanks the Spanish Ministry of Education for a FPU fellowship. The authors are grateful to C. Dorronsoro for pointing out a Matlab script for flattening the background of the data shown in Fig. 4 and helping with its implementation., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Coherent scatter-controlled phase-change grating structures in silicon using femtosecond laser pulses

  • Fuentes-Edfuf, Yasser
  • García-Lechuga, Mario
  • Puerto, D.
  • Florian, Camilo
  • García-Leis, Adianez
  • Sánchez-Cortés, Santiago
  • Solís Céspedes, Javier
  • Siegel, Jan
12 pags., 12 figs. -- Open Access funded by Creative Commons Atribution Licence 4.0, Periodic structures of alternating amorphous-crystalline fringes have been fabricated in silicon using repetitive femtosecond laser exposure (800 nm wavelength and 120 fs duration). The method is based on the interference of the incident laser light with far- and near-field scattered light, leading to local melting at the interference maxima, as demonstrated by femtosecond microscopy. Exploiting this strategy, lines of highly regular amorphous fringes can be written. The fringes have been characterized in detail using optical microscopy combined modelling, which enables a determination of the three-dimensional shape of individual fringes. 2D micro-Raman spectroscopy reveals that the space between amorphous fringes remains crystalline. We demonstrate that the fringe period can be tuned over a range of 410 nm - 13 μm by changing the angle of incidence and inverting the beam scan direction. Fine control over the lateral dimensions, thickness, surface depression and optical contrast of the fringes is obtained via adjustment of pulse number, fluence and spot size. Large-area, highly homogeneous gratings composed of amorphous fringes with micrometer width and millimeter length can readily be fabricated. The here presented fabrication technique is expected to have applications in the fields of optics, nanoelectronics, and mechatronics and should be applicable to other materials., M.G.-L. thanks the Spanish Ministry of Education for a FPU fellowship. This work was supported by the LiNaBioFluid project (H2020-FETOPEN-2014-2015RIA, grant 665337) of the European Commission; and the research grant (TEC2014-52642-C2-1-R) from the Spanish Ministry of Economy and Competitiveness., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mimicking bug-like surface structures and their fluid transport produced by ultrashort laser pulse irradiation of steel

  • Kirner, S. V.
  • Florian, Camilo
  • Solís Céspedes, Javier
  • Siegel, Jan
  • Bonse, J.
S. V. Kirner et al. -- 13 pags., 14 figs., 2 tabs., Ultrashort laser pulses with durations in the fsto- ps range were used for large area surface processing of steel aimed at mimicking the morphology and extraordinary wetting behaviour of bark bugs (Aradidae) found in nature. The processing was performed by scanning the laser beam over the surface of polished flat sample surfaces. A systematic variation of the laser processing parameters (peak fluence and effective number of pulses per spot diameter) allowed the identification of different regimes associated with characteristic surface morphologies (laser-induced periodic surface structures, i.e., LIPSS, grooves, spikes, etc.). Moreover, different laser processing strategies, varying laser wavelength, pulse duration, angle of incidence, irradiation atmosphere, and repetition rates, allowed to achieve a range of morphologies that resemble specific structures found on bark bugs. For identifying the ideal combination of parameters for mimicking bug-like structures, the surfaces were inspected by scanning electron microscopy. Inparticular, tilted micrometre-sized spikes are the best match for the structure found on bark bugs. Complementary to the morphology study, the wetting behaviour of the surface structures for water and oil was examined in terms of philic/ phobic nature and fluid transport. These results point out a route towards reproducing complex surface structures inspired by nature and their functional response in technologically relevant materials., This work has received funding from the Horizon 2020 European Union’s research and innovation programme under Grant Agreement No. 665337 (“LiNaBioFluid”; URL: http://www.laserbiofluid. eu)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Biomimetic surface structures in steel fabricated with femtosecond laser pulses: influence of laser rescanning on morphology and wettability

  • Florian, Camilo
  • Mimidis, A.
  • Puerto, D.
  • Skoulas, E.
  • Stratakis, E.
  • Solís Céspedes, Javier
  • Siegel, Jan
11 pags., 5 figs., 1 tab. -- Open Access funded by Creative Commons Atribution Licence 4.0. -- This article is part of the Thematic Series "Biological and biomimetic surfaces: adhesion, friction and wetting phenomena"., The replication of complex structures found in nature represents an enormous challenge even for advanced fabrication techniques, such as laser processing. For certain applications, not only the surface topography needs to be mimicked, but often also a specific function of the structure. An alternative approach to laser direct writing of complex structures is the generation of laser-induced periodic surface structures (LIPSS), which is based on directed self-organization of the material and allows fabrication of specific micro- and nanostructures over extended areas. In this work, we exploit this approach to fabricate complex biomimetic structures on the surface of steel 1.7131 formed upon irradiation with high repetition rate femtosecond laser pulses. In particular, the fabricated structures show similarities to the skin of certain reptiles and integument of insects. Different irradiation parameters are investigated to produce the desired structures, including laser repetition rate and laser fluence, paying special attention to the influence of the number of times the same area is rescanned with the laser. The latter parameter is identified to be crucial for controlling the morphology and size of specific structures. As an example for the functionality of the structures, we have chosen the surface wettability and studied its dependence on the laser processing parameters. Contact angle measurements of water drops placed on the surface reveal that a wide range of angles can be accessed by selecting the appropriate irradiation parameters, highlighting also here the prominent role of the number of scans., This work has been supported by the LiNaBioFluid Project (H2020-FETOPEN-2014–2015RIA, Grant No. 665337) of the European Commission as well as the research grant (TEC2014–52642-C2–1-R) from the Spanish Ministry of Economy and Competitiveness, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tuning the period of femtosecond laser induced surface structures in steel: From angled incidence to quill writing

  • Fuentes-Edfuf, Yasser
  • Sánchez-Gil, José A.
  • Garcia-Pardo, Marina
  • Serna, Rosalía
  • Tsibidis, G. D.
  • Giannini, V.
  • Solís Céspedes, Javier
  • Siegel, Jan
8 pags., 8 figs., 1 app., Exposure of metal surfaces to multiple ultrashort laser pulses under certain conditions leads to the formation of well-defined periodic surface structures. We show how the period of such structures in steel can be tuned over a wide range by controlling the complex interaction mechanisms triggered in the material. Amongst the different irradiation parameters that influence the properties of the induced structures, the angle of incidence of the laser beam occupies a prominent role. We present an experimental and theoretical investigation of this angle dependence in steel upon irradiation with laser pulses of 120¿fs duration and 800¿nm wavelength, while moving the sample at constant speed. Our findings can be grouped into two blocks. First, we observe the spatial coexistence of two different ripple periods at the steel surface, both featuring inverse scaling upon angle increase, which are related to forward and backward propagation of surface plasmon polaritons. To understand the underlying physical phenomena, we extend a recently developed model that takes into account quantitative properties of the surface roughness to the case of absorbing metals (large imaginary part of the dielectric function), and obtain an excellent match with the experimentally observed angle dependence. As second important finding, we observe a quill writing effect, also termed non-reciprocal writing, in form of a significant change of the ripple period upon reversing the sample movement direction. This remarkable phenomenon has been observed so far only inside dielectric materials and our work underlines its importance also in laser surface processing. We attribute the origin of symmetry breaking to the non-symmetric micro- and nanoscale roughness induced upon static multiple pulse irradiation, leading to non-symmetric modification of the wavevector of the coupled surface plasmon polariton., JSi, JSo and YF acknowledge the Spanish Ministry of Science,Innovation and Universities forfinancial support through researchgrant UDiSON (TEC2017-82464-R), the European Commission for grantLiNaBioFluid (FETOPEN 665337) and Consejo Superior deInvestigaciones Científicas for the project INTRAMURALES201850E057. RS acknowledges thefinancial support from the Spanishproject RTI2018-096498-B-I00 (MCIU/AEI/FEDER, UE). VG and JASGacknowledge the Spanish Ministerio de Economia y Competitividad forfinancial support through the grants LENSBEAM (FIS2015-69295-C3-2-P) and NANOTOPO (FIS2017-91413-EXP), and also Consejo Superiorde Investigaciones Científicas (INTRAMURALES 201750I039). G.D.T.acknowledgesfinancial support from Nanoscience Foundries and FineAnalysis (NFFA)–Europe H2020-INFRAIA-2014-2015 (under Grantagreement No 654360) and COST Action TUMIEE (supported by COST-European Cooperation in Science and Technology)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Surface Plasmon Polaritons on Rough Metal Surfaces: Role in the Formation of Laser-Induced Periodic Surface Structures

  • Fuentes-Edfuf, Yasser
  • Sánchez-Gil, José A.
  • Florian, Camilo
  • Giannini, V.
  • Solís Céspedes, Javier
  • Siegel, Jan
8 pags., 5 figs., 1 tab. -- Open Access funded by Creative Commons Atribution Licence 4.0, The formation of self-organized laser-induced periodic surface structures (LIPSS) in metals, semiconductors, and dielectrics upon pulsed laser irradiation is a well-known phenomenon, receiving increased attention because of their huge technological potential. For the case of metals, a major role in this process is played by surface plasmon polaritons (SPPs) propagating at the interface of the metal with the medium of incidence. Yet, simple and advanced models based on SPP propagation sometimes fail to explain experimental results, even of basic features such as the LIPSS period. We experimentally demonstrate, for the particular case of LIPSS on Cu, that significant deviations of the structure period from the predictions of the simple plasmonic model are observed, which are very pronounced for elevated angles of laser incidence. In order to explain this deviation, we introduce a model based on the propagation of SPPs on a rough surface that takes into account the influence of the specific roughness properties on the SPP wave vector. Good agreement of the modeling results with the experimental data is observed, which highlights the potential of this model for the general understanding of LIPSS in other metals., Jan Siegel, Javier Solis, Y.F.-E., and C.F. acknowledge the Spanish Ministry of Science, Innovation and Universities for financial support through research grant UDiSON (TEC2017- 82464-R) and the European Commission for grant LiNaBioFluid (FETOPEN 665337). V.G. and JASG acknowledge the Spanish Ministerio de Economia y Competitividad for financial support through the grants LENSBEAM (FIS2015-69295-C3- 2-P) and NANOTOPO (FIS2017-91413-EXP) and also Consejo Superior de Investigaciones Cienti ́ ficas (INTRAMURALES 201750I039).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The Role of the Laser-Induced Oxide Layer in the Formation of Laser-Induced Periodic Surface Structures

  • Florian, Camilo
  • Déziel, Jean-Luc
  • Kirner, S. V.
  • Siegel, Jan
  • Bonse, J.
18 pags., 11 figs., Laser-induced periodic surface structures (LIPSS) are often present when processing solid targets with linearly polarized ultrashort laser pulses. The dierent irradiation parameters to produce them on metals, semiconductors and dielectrics have been studied extensively, identifying suitable regimes to tailor its properties for applications in the fields of optics, medicine, fluidics and tribology, to name a few. One important parameter widely present when exposing the samples to the high intensities provided by these laser pulses in air environment, that generally is not considered, is the formation of a superficial laser-induced oxide layer. In this paper, we fabricate LIPSS on a layer of the oxidation prone hard-coating material chromium nitride in order to investigate the impact of the laser-induced oxide layer on its formation. A variety of complementary surface analytic techniques were employed, revealing morphological, chemical and structural characteristics of well-known high-spatial frequency LIPSS (HSFL) together with a new type of low-spatial frequency LIPSS (LSFL) with an anomalous orientation parallel to the laser polarization. Based on this input, we performed finite-dierence time-domain calculations considering a layered system resembling the geometry of the HSFL along with the presence of a laser-induced oxide layer. The simulations support a scenario that the new type of LSFL is formed at the interface between the laser-induced oxide layer and the non-altered material underneath. These findings suggest that LSFL structures parallel to the polarization can be easily induced in materials that are prone to oxidation., This work was supported through the European Horizon 2020 FET Open programme by the following projects: “CellFreeImplant” (Grant Agreement No. 800832), “LiNaBioFluid” (Grant Agreement No. 665337), and the Spanish Ministry of Science, Innovation by the project “UDiSON” (TEC2017–82464–R) and the collaborative project i-Link+2018 (Reference LINKA20044).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Heat Accumulation on Morphology Debris Deposition and Wetting of LIPSS on Steel upon High Repetition Rate Femtosecond Pulses Irradiation

  • Florian, Camilo
  • Fuentes-Edfuf, Yasser
  • Solís Céspedes, Javier
  • Skoulas, E.
  • Stratakis, E.
  • Sánchez-Cortés, Santiago
  • Siegel, Jan
17 pags., 8 figs. -- This article belongs to the Special Issue Short and Ultra-Short Laser Materials Processing – Advantages and Applications, The fabrication of laser-induced periodic surface structures (LIPSS) over extended areas at high processing speeds requires the use of high repetition rate femtosecond lasers. It is known that industrially relevant materials such as steel experience heat accumulation when irradiated at repetition rates above some hundreds of kHz, and significant debris redeposition can take place. However, there are few studies on how the laser repetition rate influences both the debris deposition and the final LIPSS morphology. In this work, we present a study of fs laser-induced fabrication of low spatial frequency LIPSS (LSFL), with pulse repetition rates ranging from 10 kHz to 2 MHz on commercially available steel. The morphology of the laser-structured areas as well as the redeposited debris was characterized by scanning electron microscopy (SEM) and µ-Raman spectroscopy. To identify repetition rate ranges where heat accumulation is present during the irradiations, we developed a simple heat accumulation model that solves the heat equation in 1 dimension implementing a Forward differencing in Time and Central differencing in Space (FTCS) scheme. Contact angle measurements with water demonstrated the influence of heat accumulation and debris on the functional wetting behavior. The findings are directly relevant for the processing of metals using high repetition rate femtosecond lasers, enabling the identification of optimum conditions in terms of desired morphology, functionality, and throughput., This research was supported by the LiNaBioFluid Project (H2020-FETOPEN-2014–2015RIA, Grant No. 665337) of the European Commission as well as the research grants (TEC2017-82464-R and PiD2020-112770RB-C21) from the Spanish Ministry of Economy and Competitiveness. C.F. acknowledges the support from the European Commission through the Marie Curie Individual Fellowship—Global Grant No. 844977.