Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 30
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Discrete empirical interpolation for hyper-reduction of hydro-mechanical problems in groundwater flow through soil

  • Nasika, Christina
  • Díez, Pedro|||0000-0001-6464-6407
  • Gerard, Pierre
  • Massart, Thierry J.
  • Zlotnik, Sergio|||0000-0001-9674-8950
This is the peer reviewed version of the following article: Nasika, C. [et al.]. Discrete empirical interpolation for hyper-reduction of hydro-mechanical problems in groundwater flow through soil. "International journal for numerical and analytical methods in geomechanics", 10 Abril 2023, vol. 47, núm. 5, p. 667-693, which has been published in final form at https://onlinelibrary.wiley.com/doi/10.1002/nag.3487. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Use of Self-Archived Versions. This article may not be enhanced, enriched or otherwise transformed into a derivative work, without express permission from Wiley or by statutory rights under applicable legislation. Copyright notices must not be removed, obscured or modified. The article must be linked to Wiley’s version of record on Wiley Online Library and any embedding, framing or otherwise making available the article or pages thereof by third parties from platforms, services and websites other than Wiley Online Library must be prohibited., The recent surge in the availability of sensor data and computational resources has fostered the development of technologies for optimization, control, and monitoring of large infrastructures, integrating data and numerical modeling. The major bottleneck in this type of technologies is the model response time, since repetitive solutions are typically required. To reduce the computational time, reduced order models (ROMs) are used as surrogates for expensive finite element (FE) simulations enabling the use of complex models in this type of applications. In this work, ROMs are explored for the solution of the fully coupled hydro-mechanical system of equations that governs the water flow through partially saturated soil. The POD-based Reduced Basis Method and the Discrete Empirical Interpolation Method (DEIM), as well as its localized version (LDEIM), are examined in solving a parametrized problem simulating the mechanical loading of an embankment dam. Hydraulic and mechanical soil properties are considered as parameters. It is shown that the combination of these methods results in simulations that require 1/10 to 1/100 of the FE response time. Moreover, the method is shown to yield scaling efficiency gains with increasing problem size., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

An acoustic Riemann solver for large strain computationalcontact dynamics

  • Runcie, Callum J.
  • Lee, Chun Hean
  • Haider, Jibran
  • Gil, Antonio J.
  • Bonet Carbonell, Javier|||0000-0002-0430-5181
This article presents a vertex-centered finite volume algorithm for the explicit dynamic analysis of large strain contact problems. The methodology exploits the use of a system of first order conservation equations written in terms of the linear momentum and a triplet of geometric deformation measures (comprising the deformation gradient tensor, its co-factor, and its Jacobian) together with their associated jump conditions. The latter can be used to derive several dynamic contact models ensuring the preservation of hyperbolic characteristic structure across solution discontinuities at the contact interface, a clear advantage over the standard quasi-static contact models where the influence of inertial effects at the contact interface is completely neglected. Taking advantage of the conservative nature of the formalism, both kinetic (traction) and kinematic (velocity) contact interface conditions are explicitly enforced at the fluxes through the use of appropriate jump conditions. Specifically, the kinetic condition is enforced in the usual linear momentum equation, whereas the kinematic condition can now be easily enforced in the geometric conservation equations without requiring a computationally demanding iterative algorithm. Additionally, a total variation diminishing shock capturing technique can be suitably incorporated in order to improve dramatically the performance of the algorithm at the vicinity of shocks. Moreover, and to guarantee stability from the spatial discretization standpoint, global entropy production is demonstrated through the satisfaction of semi-discrete version of the classical Coleman–Noll procedure expressed in terms of the time rate of the so-called Hamiltonian energy of the system. Finally, a series of numerical examples is examined in order to assess the performance and applicability of the algorithm suitably implemented in OpenFOAM. The knowledge of the potential contact loci between contact interfaces is assumed to be known a priori., Antonio J. Gil and Chun Hean Lee would like to acknowledge the financial support received through the project Marie Skłodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with Grant number 764636. Callum J., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Towards real time assessment of earthfill dams via Model Order Reduction

  • Nasika, Christina
  • Díez, Pedro|||0000-0001-6464-6407
  • Gerard, Pierre
  • Massart, Thierry J.
  • Zlotnik, Sergio|||0000-0001-9674-8950
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The use of Internet of Things (IoT) technologies is becoming a preferred solution for the assessment of tailings dams’ safety. Real-time sensor monitoring proves to be a key tool for reducing the risk related to these ever-evolving earth-fill structures, that exhibit a high rate of sudden and extremely hazardous failures. In order to optimally exploit real-time embankment monitoring, one major hindrance has to be overcome: the creation of a supporting numerical model for stability analysis, with rapid-enough response to perform data assimilation in real time. A model should therefore be built, such that its response can be obtained faster than the physical evolution of the phenomenon to be analyzed. In this work, Reduced Order Modeling (ROM) is used to boost computational efficiency in solving the coupled hydromechanical system of equations governing the problem. POD-based reduction has been studied in order to treat the problem of groundwater flow, coupled to the geomechanical problem. The Reduced Basis method is applied to the coupled hydro-mechanical equations that govern the flow of groundwater, that are made non-linear as a result of considering an unsaturated soil. The resulting model’s performance is assessed by solving a 2D and a 3D problem relevant to tailings dams’ safety. The ROM technique achieves a speedup of 3 to 15 times with respect to the full-order model (FOM) while maintaining high levels of accuracy., This work has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie SklodowskaCurie grant agreement No 764636, for the research project ProTechTion. We thank Professor Sebatian Olivella (Escola de Camins, Universitat Politècnica de Catalunya) for his much appreciated assistance. Pedro Díez and Sergio Zlotink are grateful for the financial support provided by the Spanish Ministry of Economy and Competitiveness (Grant agreement No. DPI2017-85139-C2-2-R), by the Generalitat de Catalunya (Grant agreement No. 2017-SGR-1278), and by project H2020-RISE MATH-ROCKS GA no 777778., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A first-order hyperbolic Arbitrary Lagrangian Eulerian conservation formulation for nonlinear solid dynamics in irreversible processes

  • Giusto, Thomas di
  • Chun Hean, Lee
  • Antonio Javier, Gil
  • Bonet Carbonell, Javier|||0000-0002-0430-5181
  • Wood, Clare
  • Giacomini, Matteo|||0000-0001-6094-5944
© 2024 The Author(s). Published by Elsevier Inc. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/)., The paper introduces a computational framework that makes use of a novel Arbitrary Lagrangian Eulerian (ALE) conservation law formulation for nonlinear solid dynamics. In addition to the standard mass conservation law and the linear momentum conservation law, the framework extends its application to consider more general irreversible processes such as thermo-elasticity and thermo-visco-plasticity. This requires the incorporation of the first law of thermodynamics, expressed in terms of the entropy density, as an additional conservation law. To disassociate material particles from mesh positions, the framework introduces an additional reference configuration, extending beyond conventional material and spatial descriptions. The determination of the mesh motion involves the solution of a conservation-type momentum equation, ensuring optimal mesh movement and contributing to maintaining a high-quality mesh and improving solution accuracy, particularly in regions undergoing large plastic flows. To maintain equal convergence orders for all variables (strains/stresses, velocities/displacements and temperature/entropy), the standard deformation gradient tensor (measured from material to spatial configuration) is evaluated through a multiplicative decomposition into two auxiliary deformation gradient tensors. Both are obtained through additional first-order conservation laws. The exploitation of the hyperbolic nature of the underlying system, together with accurate wave speed bounds, ensures the stability of explicit time integrators. For spatial discretisation, a vertex-centred Godunov-type Finite Volume method is employed and suitably adapted to the formulation at hand. To guarantee stability from both the continuum and the semi-discretisation standpoints, a carefully designed numerical interface flux is presented. Lyapunov stability analysis is carried out by evaluating the time variation of the Ballistic energy of the system, aiming to ensure the positive production of numerical entropy. Finally, a variety of three dimensional benchmark problems are presented to illustrate the robustness and applicability of the framework., The first, second and third authors would like to acknowledge the financial support received through the project Marie Skłodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with grant number 764636. CHL acknowledges the support provided by FIFTY2 Technology GmbH via project reference 322835. AJG acknowledges the support provided by UK AWE via project PO 40062030. JB acknowledges the financial support received via project POTENTIAL (PID2022-141957OB-C21) funded by MICIU/AEI/10.13039/501100011033/FEDER, UE. MG acknowledges the Spanish Ministry of Science, Innovation and Universities and Spanish State Research Agency MICIU/AEI/10.13039/501100011033 (Grants No. PID2020-113463RB-C33 and CEX2018-000797-S) and the Generalitat de Catalunya (Grant No. 2021-SGR-01049). MG is Fellow of the Serra Húnter Programme of the Generalitat de Catalunya., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Nonintrusive parametric solutions in structural dynamics

  • Cavaliere, Fabiola|||0000-0002-4148-7594
  • Zlotnik, Sergio|||0000-0001-9674-8950
  • Larráyoz Izcara, Xabier
  • Díez, Pedro|||0000-0001-6464-6407
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, A nonintrusive reduced order method able to solve a parametric modal analysis is proposed in this work. The main objective is being able to efficiently identify how a variation of user-defined parameters affects the dynamic response of the structure in terms of fundamental natural frequencies and corresponding mode shapes. A parametric version of the inverse power method (IPM) is presented by using the proper generalised decomposition (PGD) rationale. The proposed approach utilises the socalled encapsulated PGD toolbox and includes a new algorithm for computing the square root of a parametric object. With only one offline computation, the proposed PGD-IPM approach provides an analytical parametric expression of the smallest (in magnitude) eigenvalue (or natural frequency) and corresponding eigenvector (mode shape), which contains all the possible solutions for every combination of the parameters within pre-defined ranges. A Lagrange multiplier deflation technique is introduced in order to compute subsequent eigenpairs, which is also valid to overcome the stiffness matrix singularity in the case of a free-free structure. The proposed approach is nonintrusive and it is therefore possible to be integrated with commercial finite element (FE) packages. Two numerical examples are shown to underline the properties of the technique. The first example includes one material and one geometric parameter. The second example shows a more realistic industrial example, where the nonintrusivity of the approach is demonstrated by employing a commercial FE package for assembling the FE matrices. Finally, a multi-objective optimisation study is performed proving that the developed method could significantly assist the decision-making during the preliminary phase of a new design process., This project is part of the Marie Skłodowska-Curie ITN-EJD ProTechTion funded by the European Union Horizon 2020 research and innovation program with Grant Number 764636. The work of Fabiola Cavaliere, Sergio Zlotnik and Pedro Díez is partially supported by the MCIN/AEI/10.13039/501100011033, Spain (Grant Number: PID2020-113463RB-C32, PID2020-113463RB-C33 and CEX2018-000797-S). Ruben Sevilla also acknowledges the support of the Engineering and Physical Sciences Research Council (Grant Number: EP/P033997/1)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Phase distribution and properties identification of heterogeneous materials: a data-driven approach

  • Valdés Alonzo, Gabriel Rolando
  • Binetruy, Christophe
  • Eck, Benedikt
  • García González, Alberto|||0000-0003-2841-016X
  • Leygue, Adrien
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This paper presents a new methodology to extend the Data-Driven Identification (DDI) to heterogeneous samples made of multiple elastic materials. By using the Correspondence Analysis (CA) technique to post-process DDI, we are able to identify multiple material databases representative of the material behavior of each phase. Simultaneously, we localize the different phases (matrix and inclusions) in the sample. For different contrasts between phases, the method is tested on synthetically generated data and a parametric study is performed. Furthermore, we show that it is possible to iterate between DDI and CA in order to improve the method’s predictions when it is limited by scarce input data. In all the cases studied, the methodology proves to be effective for estimating stresses, as well as for identifying the different phases in the sample., This project is part of the Marie Sklodowska-Curie ITN-EJD ProTechTion funded by the European Union Horizon 2020 research and innovation program with Grant Number 764636., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A new Updated Reference Lagrangian Smooth Particle Hydrodynamics algorithm for isothermal elasticity and elasto-plasticity

  • Refachinho de Campos, Paulo Roberto
  • Antonio Javier, Gil
  • Chun Hean, Lee
  • Giacomini, Matteo|||0000-0001-6094-5944
  • Bonet Carbonell, Javier|||0000-0002-0430-5181
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This paper presents a new Updated Reference Lagrangian Smooth Particle Hydrodynamics (SPH) algorithm for the analysis of large deformation isothermal elasticity and elasto-plasticity. Taking as point of departure a Total Lagrangian setting and considering as referential configuration an intermediate configuration of the deformation process, the equation of conservation of linear momentum and three geometric conservation laws (for the deformation gradient, its cofactor and its determinant) are re-written leading to a very generic system of first order conservation laws. The key feature of the formulation is a suitable multiplicative decomposition of the conservation variables, leading to a very simple final set of equations with striking similarities to the conventional Total Lagrangian system albeit re-written in terms of alternative Referential Updated conservation variables which are evolved in time. Taking advantage of this new Updated Reference Lagrangian formalism, a second order entropy-stable SPH upwinding stabilisation method will be introduced. With respect to previous publications by the group, a new three-stage Runge–Kutta time integration method is implemented in order to increase the CFL stability restriction. Finally, and to demonstrate the robustness and applicability of the methodology, a wide spectrum of challenging problems will be presented and compared, including some benchmark three-dimensional large deformation elasto-plasticity problems. To facilitate its ease of implementation, the paper explores the use of a series of novel expressions for the evaluation of kernels and the gradients of kernels to provide the SPH user the freedom to choose amongst various options, all leading to equally convincingly robust results., The authors would like to acknowledge the financial support received through the project Marie SkłodowskaCurie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with Grant Number 764636. The third author also gratefully acknowledges the support provided by the EPSRC Strategic Support Package: Engineering of Active Materials by Multiscale/Multiphysics Computational Mechanics - EP/R008531/1. The fourth author acknowledges the support of the Serra Hunter Programme of the Generalitat de ´ Catalunya, the Spanish Ministry of Economy and Competitiveness (Grant agreement No. PID2020-113463RB-C33) and the Spanish Ministry of Economy and Competitiveness through the Severo Ochoa programme for centres of excellence in RTD (Grant agreement No. CEX2018-000797-S)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Nonintrusive reduced order model for parametric solutions of inertia relief problems

  • Cavaliere, Fabiola|||0000-0002-4148-7594
  • Zlotnik, Sergio|||0000-0001-9674-8950
  • Sevilla Cárdenas, Rubén|||0000-0002-0061-6214
  • Larráyoz Izcara, Xabier
  • Díez, Pedro|||0000-0001-6464-6407
This is the peer reviewed version of the following article: Cavaliere, F. [et al.]. Nonintrusive reduced order model for parametric solutions of inertia relief problems. "International journal for numerical methods in engineering", 30 Agost 2021, vol. 122, núm. 16, p. 4270-4291., which has been published in final form at DOI:10.1002/nme.6702. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., The Inertia Relief (IR) technique is widely used by industry and produces equilibrated loads allowing to analyze unconstrained systems without resorting to the more expensive full dynamic analysis. The main goal of this work is to develop a computational framework for the solution of unconstrained parametric structural problems with IR and the Proper Generalized Decomposition (PGD) method. First, the IR method is formulated in a parametric setting for both material and geometric parameters. A reduced order model using the encapsulated PGD suite is then developed to solve the parametric IR problem, circumventing the so-called curse of dimensionality. With just one offline computation, the proposed PGD-IR scheme provides a computational vademecum that contains all the possible solutions for a predefined range of the parameters. The proposed approach is nonintrusive and it is therefore possible to be integrated with commercial finite element (FE) packages. The applicability and potential of the developed technique is shown using a three-dimensional test case and a more complex industrial test case. The first example is used to highlight the numerical properties of the scheme, whereas the second example demonstrates the potential in a more complex setting and it shows the possibility to integrate the proposed framework within a commercial FE package. In addition, the last example shows the possibility to use the generalized solution in a multi-objective optimization setting., This project is part of the Marie Sk lodowska-Curie ITN-EJD ProTechTion funded by the European Union Horizon 2020 research and innovation program with grant number 764636. The work of Fabiola Cavaliere, Sergio Zlotnik and Pedro D´ıez is partially supported by the Spanish Ministry of Economy and Competitiveness, Spain (Grant number: DPI2017-85139- C2-2-R) and by the Generalitat de Catalunya, Spain (Grant number: 2017-SGR-1278). Ruben Sevilla also acknowledges the support of the Engineering and Physical Sciences Research Council (Grant number: EP/P033997/1)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

A robust updated lagrangian smooth particle hydrodynamics for fast solid dynamics

  • Refachinho de Campos, Paulo Roberto
  • Antonio Javier, Gil
  • Chun Hean, Lee
  • Huerta, Antonio|||0000-0003-4198-3798
  • Giacomini, Matteo|||0000-0001-6094-5944
  • Bonet Carbonell, Javier|||0000-0002-0430-5181
This paper introduces a new Incremental Updated Lagrangian Smooth Particle Hydrodynamics (SPH) computational framework in the form of a system of first order conservation laws. Specifically, the linear momentum conservation equation is solved in an incremental manner in conjunction with a set of incremental geometric conservation laws for the minors of the deformation gradient tensor, namely the deformation gradient, its cofactor and its Jacobian. Taking advantage of this new formalism, an entropy-stable upwinding stabilisation SPH method is introduced, with no user-defined regularisation parameters involved. The resulting semi-discrete SPH equations are variationally consistent and also ensure the global production of numerical entropy, demonstrated through the semi-discrete version of the classical Coleman-Noll procedure. The overall methodology will be shown to be capable of handling large deformations without persistent numerical shortcomings often encountered in the classical SPH (displacement-based) formulation., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

An acoustic Riemann solver for large strain computational contact dynamics

  • Runcie, Callum J.
  • Lee, Chun Hean
  • Haider, Jibran
  • Gil, Antonio
  • Bonet Carbonell, Javier|||0000-0002-0430-5181
This article presents a vertex-centered finite volume algorithm for the explicit dynamic analysis of large strain contact problems. The methodology exploits the use of a system of first order conservation equations written in terms of the linear momentum and a triplet of geometric deformation measures (comprising the deformation gradient tensor, its co-factor, and its Jacobian) together with their associated jump conditions. The latter can be used to derive several dynamic contact models ensuring the preservation of hyperbolic characteristic structure across solution discontinuities at the contact interface, a clear advantage over the standard quasi-static contact models where the influence of inertial effects at the contact interface is completely neglected. Taking advantage of the conservative nature of the formalism, both kinetic (traction) and kinematic (velocity) contact interface conditions are explicitly enforced at the fluxes through the use of appropriate jump conditions. Specifically, the kinetic condition is enforced in the usual linear momentum equation, whereas the kinematic condition can now be easily enforced in the geometric conservation equations without requiring a computationally demanding iterative algorithm. Additionally, a total variation diminishing shock capturing technique can be suitably incorporated in order to improve dramatically the performance of the algorithm at the vicinity of shocks. Moreover, and to guarantee stability from the spatial discretization standpoint, global entropy production is demonstrated through the satisfaction of semi-discrete version of the classical Coleman–Noll procedure expressed in terms of the time rate of the so-called Hamiltonian energy of the system. Finally, a series of numerical examples is examined in order to assess the performance and applicability of the algorithm suitably implemented in OpenFOAM. The knowledge of the potential contact loci between contact interfaces is assumed to be known a priori., Callum J. Runcie and Chun Hean Lee gratefully acknowledge the support provided by the EPSRC Strategic Support Package: Engineering of Active Materials by Multiscale/Multiphysics Computational Mechanics - EP/R008531/1. Antonio J. Gil and Chun Hean Lee would like to acknowledge the financial support received through the project Marie Skłodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with Grant number 764636. Callum J. Runcie and Chun Hean Lee would also like to acknowledge the many useful discussions with Dr. Peter Grassl from University of Glasgow., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A first-order hyperbolic arbitrary Lagrangian Eulerian conservation formulation for non-linear solid dynamics

  • Giusto, Thomas di
  • Chun Hean, Lee
  • Antonio Javier, Gil
  • Bonet Carbonell, Javier|||0000-0002-0430-5181
  • Giacomini, Matteo|||0000-0001-6094-5944
The paper introduces a computational framework using a novel Arbitrary Lagrangian Eulerian (ALE) formalism in the form of a system of first-order conservation laws. In addition to the usual material and spatial configurations, an additional referential (intrinsic) configuration is introduced in order to disassociate material particles from mesh positions. Using isothermal hyperelasticity as a starting point, mass, linear momentum and total energy conservation equations are written and solved with respect to the reference configuration. In addition, with the purpose of guaranteeing equal order of convergence of strains/stresses and velocities/displacements, the computation of the standard deformation gradient tensor (measured from material to spatial configuration) is obtained via its multiplicative decomposition into two auxiliary deformation gradient tensors, both computed via additional first-order conservation laws. Crucially, the new ALE conservative formulation will be shown to degenerate elegantly into alternative mixed systems of conservation laws such as Total Lagrangian, Eulerian and Updated Reference Lagrangian. Hyperbolicity of the system of conservation laws will be shown and the accurate wave speed bounds will be presented, the latter critical to ensure stability of explicit time integrators. For spatial discretisation, a vertex-based Finite Volume method is employed and suitably adapted. To guarantee stability from both the continuum and the semi-discretisation standpoints, an appropriate numerical interface flux (by means of the Rankine–Hugoniot jump conditions) is carefully designed and presented. Stability is demonstrated via the use of the time variation of the Hamiltonian of the system, seeking to ensure the positive production of numerical entropy. A range of three dimensional benchmark problems will be presented in order to demonstrate the robustness and reliability of the framework. Examples will be restricted to the case of isothermal reversible elasticity to demonstrate the potential of the new formulation., The first, second and third authors would like to acknowledge the financial support received through the project MarieSkłodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation programwith grant number 764636. Chun Hean Lee acknowledges the support provided by the EPSRC Strategic Support Package:Engineering of Active Materials by Multiscale/Multiphysics Computational Mechanics–EP/R008531/1. Antonio J. Gilacknowledges the support provided by UK AWE via project PO 40062030. Javier Bonet acknowledges the financial supportreceived via project POTENTIAL (PID2022-141957OB-C21) funded by MCIN/AEI/10.13039/501100011033/FEDER, UE.Matteo Giacomini acknowledges the Spanish Ministry of Science and Innovation and Spanish State Research AgencyMCIN/AEI/10.13039/501100011033 (Grant nos. PID2020-113463RB-C33 and CEX2018-000797-S). Matteo Giacomini isFellow of the Serra Húnter Programme of the Generalitat de Catalunya., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A hybrid pressure formulation of the face-centred finite volume method for viscous laminar incompressible flows

  • Giacomini, Matteo|||0000-0001-6094-5944
  • Cortellessa, Davide
  • Malikoski Vieira, Luan
  • Sevilla, Rubén
  • Huerta, Antonio|||0000-0003-4198-3798
This work presents a hybrid pressure face-centred finite volume (FCFV) solver to simulate steady-state incompressible Navier-Stokes flows. The method leverages the robustness, in the incompressible limit, of the hybridisable discontinuous Galerkin paradigm for compressible and weakly compressible flows to derive the formulation of a novel, low-order face-based discretization. The incompressibility constraint is enforced in a weak sense by introducing an inter-cell mass flux, defined in terms of a new, hybrid variable that represents the pressure at the cell faces. This results in a new hybridization strategy where cell variables (velocity, pressure, and deviatoric strain rate tensor) are expressed as a function of velocity and pressure at the barycentre of the cell faces. The hybrid pressure formulation provides first-order convergence of all variables, including the stress, without the need for gradient reconstruction, thus being less sensitive to cell type, stretching, distortion, and skewness than traditional low-order finite volume solvers. Numerical benchmarks of Navier-Stokes flows at low and moderate Reynolds numbers, in two and three dimensions, are presented to evaluate the accuracy and robustness of the method. In particular, the hybrid pressure formulation outperforms the FCFV method when convective effects are relevant, achieving accurate predictions on significantly coarser meshes., This work was supported by the H2020 MSCA (ITN-EJD 764636), Generalitat de Catalunya (2021-SGR-01049), Agencia Estatal de Investigación and MICIU/AEI/10.13039/501100011033 (PID2020-113463RB-C33, PID2020-113463RB-C32, CEX2018-000797-S)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

An improved updated Lagrangian SPH method for structural modelling

  • Khayyer, Abbas
  • Shimizu, Yuma
  • Chun Hean, Lee
  • Gil Ruiz, Antonio Javier
  • Gotoh, Hitoshi
  • Bonet Carbonell, Javier|||0000-0002-0430-5181
The version of record of this article, first published in Computational particle mechanics, is available online at Publisher’s website: https://doi.org/10.1007/s40571-023-00673-z, This paper presents a set of novel refined schemes to enhance the accuracy and stability of the updated Lagrangian SPH (ULSPH) for structural modelling. The original ULSPH structure model was first proposed by Gray et al. (Comput Methods Appl Mech Eng 190:6641–6662, 2001) and has been utilised for a wide range of structural analyses including metal, soil, rubber, ice, etc., although the model often faces several drawbacks including unphysical numerical damping, high-frequency noise in reproduced stress fields, presence of several artificial terms requiring ad hoc tunings and numerical instability in the presence of tensile stresses. In these regards, this study presents a set of enhanced schemes corresponding to (1) consistency correction on discretisation schemes for differential operators, (2) a numerical diffusive term incorporated in the continuity or the density rate equation, (3) tuning-free stabilising term based on Riemann solution and (4) careful control/switch of stress divergence differential operator model under tensile stresses. Qualitative/quantitative validations are conducted through several well-known benchmark tests., This study was supported by JSPS (Japan Society for the Promotion of Science) KAKENHI Grants Number JP21H01433, JP18K04368, JP21K14250 and JP22H01599. Antonio Gil and Chun Hean Lee would like to acknowledge the financial support received through the project Marie Sklodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with grant number 764636. The first author acknowledges the contribution of Mr. Kazuhiro Kinuta and Mr. Kazunori Yunoki, students of Applied Mechanics Laboratory, Kyoto University, in conducting several preliminary simulations corresponding to this study back in 2021 and 2022, respectively., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Nonintrusive parametric NVH study of a vehicle body structure

  • Cavaliere, Fabiola|||0000-0002-4148-7594
  • Zlotnik, Sergio|||0000-0001-9674-8950
  • Sevilla Càrdenas, Ruben
  • Larráyoz Izcara, Xabier
  • Díez, Pedro|||0000-0001-6464-6407
This is an Accepted Manuscript of an article published by Taylor & Francis Group in Mechanics based design of structures and machines on 27/06/22, available online at: http://www.tandfonline.com/10.1080/15397734.2022.2098140, A reduced order model technique is presented to perform the parametric Noise, Vibration and Harshness (NVH) study of a vehicle body-in-white (BIW) structure characterized by material and shape design variables. The ultimate goal is to develop a methodology which allows to efficiently explore the variation in the design space of the BIW static and dynamic global stiffnesses, such that the NVH performance can be evaluated already in the preliminary phase of the development process. The proposed technique is based on the proper generalized decomposition (PGD) method. The obtained PGD solution presents an explicit dependency on the introduced design variables, which allows to obtain solutions in 0.1 milliseconds and therefore opens the door to fast optimization studies and real-time visualizations of the results in a pre-defined range of parameters. The method is nonintrusive, such that an interaction with commercial software is possible. A parametrized finite element (FE) model of the BIW is built by means of the ANSA CAE preprocessor software, which allows to account for material and geometric parameters. A comparison between the parametric NVH solutions and the full-order FE simulations is performed using the MSC-Nastran software, to validate the accuracy of the proposed method. In addition, an optimization study is presented to find the optimal materials and shape properties with respect to the NVH performance. Finally, in order to support the designers in the decision-making process, a graphical interface app is developed which allows to visualize in real-time how changes in the design variables affect pre-defined quantities of interest., This project is part of the Marie Skłodowska-Curie ITN-EJD ProTechTion funded by the European Union Horizon 2020 research and innovation program with Grant Number 764636. The work of Fabiola Cavaliere, Sergio Zlotnik and Pedro D ıez is partially supported by the MCIN/AEI/10.13039/501100011033, Spain (Grant Number: PID2020-113463RB-C32, PID2020-113463RB-C33 and CEX2018-000797-S). Ruben Sevilla also acknowledges the support of the Engineering and Physical Sciences Research Council (Grant Number: EP/T009071/1)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A face-centred finite volume method for laminar and turbulent incompressible flows

  • Vieira, Luan M.
  • Giacomini, Matteo|||0000-0001-6094-5944
  • Sevilla, Rubén
  • Huerta, Antonio|||0000-0003-4198-3798
This work develops, for the first time, a face-centred finite volume (FCFV) solver for the simulation of laminar and turbulent viscous incompressible flows. The formulation relies on the Reynolds-averaged Navier–Stokes (RANS) equations coupled with the negative Spalart–Allmaras (SA) model and three novel convective stabilisations, inspired by Riemann solvers, are derived and compared numerically. The resulting method achieves first-order convergence of the velocity, the velocity-gradient tensor and the pressure. FCFV accurately predicts engineering quantities of interest, such as drag and lift, on unstructured meshes and, by avoiding gradient reconstruction, the method is less sensitive to mesh quality than other FV methods, even in the presence of highly distorted and stretched cells. A monolithic and a staggered solution strategies for the RANS-SA system are derived and compared numerically. Numerical benchmarks, involving laminar and turbulent, steady and transient cases are used to assess the performance, accuracy and robustness of the proposed FCFV method., The authors acknowledge the support of: H2020 MSCA ITN-EJD ProTechTion (Grant No. 764636) that partially funded the PhD scholarship of LMV; Spanish Ministry of Science, Innovation and Universities and Spanish State Research Agency MICIU/AEI/10.13039/501100011 033 (Grants No. PID2020-113463RB-C33 to MG, PID2020-113463RBC32 to AH and CEX2018-000797-S to MG and AH); Generalitat de Catalunya, Spain (Grant No. 2021-SGR-01049 to MG and AH); MG is Fellow of the Serra Húnter Programme of the Generalitat de Catalunya., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A hybrid pressure formulation of the face-centred finite volume method for viscous laminar incompressible flows

  • Giacomini, Matteo
  • Cortellessa, Davide
  • Malikoski Vieira, Luan
  • Sevilla, Rubén
  • Huerta, Antonio
This work presents a hybrid pressure face-centred finite volume (FCFV) solver to simulate steady-state incompressible Navier-Stokes flows. The method leverages the robustness, in the incompressible limit, of the hybridisable discontinuous Galerkin paradigm for compressible and weakly compressible flows to derive the formulation of a novel, low-order face-based discretization. The incompressibility constraint is enforced in a weak sense by introducing an inter-cell mass flux, defined in terms of a new, hybrid variable that represents the pressure at the cell faces. This results in a new hybridization strategy where cell variables (velocity, pressure, and deviatoric strain rate tensor) are expressed as a function of velocity and pressure at the barycentre of the cell faces. The hybrid pressure formulation provides first-order convergence of all variables, including the stress, without the need for gradient reconstruction, thus being less sensitive to cell type, stretching, distortion, and skewness than traditional low-order finite volume solvers. Numerical benchmarks of Navier-Stokes flows at low and moderate Reynolds numbers, in two and three dimensions, are presented to evaluate the accuracy and robustness of the method. In particular, the hybrid pressure formulation outperforms the FCFV method when convective effects are relevant, achieving accurate predictions on significantly coarser meshes., This work was supported by the H2020 MSCA (ITN-EJD 764636), Generalitat de Catalunya (2021-SGR-01049), Agencia Estatal de Investigación and MICIU/AEI/10.13039/501100011033 (PID2020-113463RB-C33, PID2020-113463RB-C32, CEX2018-000797-S)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A first-order hyperbolic Arbitrary Lagrangian Eulerian conservation formulation for nonlinear solid dynamics in irreversible processes

  • Giusto, Thomas di
  • Chun Hean, Lee
  • Antonio Javier, Gil
  • Bonet Carbonell, Javier
  • Wood, Clare
  • Giacomini, Matteo
The paper introduces a computational framework that makes use of a novel Arbitrary Lagrangian Eulerian (ALE) conservation law formulation for nonlinear solid dynamics. In addition to the standard mass conservation law and the linear momentum conservation law, the framework extends its application to consider more general irreversible processes such as thermo-elasticity and thermo-visco-plasticity. This requires the incorporation of the first law of thermodynamics, expressed in terms of the entropy density, as an additional conservation law. To disassociate material particles from mesh positions, the framework introduces an additional reference configuration, extending beyond conventional material and spatial descriptions. The determination of the mesh motion involves the solution of a conservation-type momentum equation, ensuring optimal mesh movement and contributing to maintaining a high-quality mesh and improving solution accuracy, particularly in regions undergoing large plastic flows. To maintain equal convergence orders for all variables (strains/stresses, velocities/displacements and temperature/entropy), the standard deformation gradient tensor (measured from material to spatial configuration) is evaluated through a multiplicative decomposition into two auxiliary deformation gradient tensors. Both are obtained through additional first-order conservation laws. The exploitation of the hyperbolic nature of the underlying system, together with accurate wave speed bounds, ensures the stability of explicit time integrators. For spatial discretisation, a vertex-centred Godunov-type Finite Volume method is employed and suitably adapted to the formulation at hand. To guarantee stability from both the continuum and the semi-discretisation standpoints, a carefully designed numerical interface flux is presented. Lyapunov stability analysis is carried out by evaluating the time variation of the Ballistic energy of the system, aiming to ensure the positive production of numerical entropy. Finally, a variety of three dimensional benchmark problems are presented to illustrate the robustness and applicability of the framework., The first, second and third authors would like to acknowledge the financial support received through the project Marie Skłodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with grant number 764636. CHL acknowledges the support provided by FIFTY2 Technology GmbH via project reference 322835. AJG acknowledges the support provided by UK AWE via project PO 40062030. JB acknowledges the financial support received via project POTENTIAL (PID2022-141957OB-C21) funded by MICIU/AEI/10.13039/501100011033/FEDER, UE. MG acknowledges the Spanish Ministry of Science, Innovation and Universities and Spanish State Research Agency MICIU/AEI/10.13039/501100011033 (Grants No. PID2020-113463RB-C33 and CEX2018-000797-S) and the Generalitat de Catalunya (Grant No. 2021-SGR-01049). MG is Fellow of the Serra Húnter Programme of the Generalitat de Catalunya., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Towards real time assessment of earthfill dams via Model Order Reduction

  • Nasika, Christina
  • Díez, Pedro
  • Gerard, Pierre
  • Massart, Thierry J.
  • Zlotnik, Sergio
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The use of Internet of Things (IoT) technologies is becoming a preferred solution for the assessment of tailings dams’ safety. Real-time sensor monitoring proves to be a key tool for reducing the risk related to these ever-evolving earth-fill structures, that exhibit a high rate of sudden and extremely hazardous failures. In order to optimally exploit real-time embankment monitoring, one major hindrance has to be overcome: the creation of a supporting numerical model for stability analysis, with rapid-enough response to perform data assimilation in real time. A model should therefore be built, such that its response can be obtained faster than the physical evolution of the phenomenon to be analyzed. In this work, Reduced Order Modeling (ROM) is used to boost computational efficiency in solving the coupled hydromechanical system of equations governing the problem. POD-based reduction has been studied in order to treat the problem of groundwater flow, coupled to the geomechanical problem. The Reduced Basis method is applied to the coupled hydro-mechanical equations that govern the flow of groundwater, that are made non-linear as a result of considering an unsaturated soil. The resulting model’s performance is assessed by solving a 2D and a 3D problem relevant to tailings dams’ safety. The ROM technique achieves a speedup of 3 to 15 times with respect to the full-order model (FOM) while maintaining high levels of accuracy., This work has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie SklodowskaCurie grant agreement No 764636, for the research project ProTechTion. We thank Professor Sebatian Olivella (Escola de Camins, Universitat Politècnica de Catalunya) for his much appreciated assistance. Pedro Díez and Sergio Zlotink are grateful for the financial support provided by the Spanish Ministry of Economy and Competitiveness (Grant agreement No. DPI2017-85139-C2-2-R), by the Generalitat de Catalunya (Grant agreement No. 2017-SGR-1278), and by project H2020-RISE MATH-ROCKS GA no 777778., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Nonintrusive reduced order model for parametric solutions of inertia relief problems

  • Cavaliere, Fabiola
  • Zlotnik, Sergio
  • Sevilla Cárdenas, Rubén
  • Larráyoz Izcara, Xabier
  • Díez, Pedro
This is the peer reviewed version of the following article: Cavaliere, F. [et al.]. Nonintrusive reduced order model for parametric solutions of inertia relief problems. "International journal for numerical methods in engineering", 30 Agost 2021, vol. 122, núm. 16, p. 4270-4291., which has been published in final form at DOI:10.1002/nme.6702. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., The Inertia Relief (IR) technique is widely used by industry and produces equilibrated loads allowing to analyze unconstrained systems without resorting to the more expensive full dynamic analysis. The main goal of this work is to develop a computational framework for the solution of unconstrained parametric structural problems with IR and the Proper Generalized Decomposition (PGD) method. First, the IR method is formulated in a parametric setting for both material and geometric parameters. A reduced order model using the encapsulated PGD suite is then developed to solve the parametric IR problem, circumventing the so-called curse of dimensionality. With just one offline computation, the proposed PGD-IR scheme provides a computational vademecum that contains all the possible solutions for a predefined range of the parameters. The proposed approach is nonintrusive and it is therefore possible to be integrated with commercial finite element (FE) packages. The applicability and potential of the developed technique is shown using a three-dimensional test case and a more complex industrial test case. The first example is used to highlight the numerical properties of the scheme, whereas the second example demonstrates the potential in a more complex setting and it shows the possibility to integrate the proposed framework within a commercial FE package. In addition, the last example shows the possibility to use the generalized solution in a multi-objective optimization setting., This project is part of the Marie Sk lodowska-Curie ITN-EJD ProTechTion funded by the European Union Horizon 2020 research and innovation program with grant number 764636. The work of Fabiola Cavaliere, Sergio Zlotnik and Pedro D´ıez is partially supported by the Spanish Ministry of Economy and Competitiveness, Spain (Grant number: DPI2017-85139- C2-2-R) and by the Generalitat de Catalunya, Spain (Grant number: 2017-SGR-1278). Ruben Sevilla also acknowledges the support of the Engineering and Physical Sciences Research Council (Grant number: EP/P033997/1)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A new Updated Reference Lagrangian Smooth Particle Hydrodynamics algorithm for isothermal elasticity and elasto-plasticity

  • Refachinho de Campos, Paulo Roberto
  • Antonio Javier, Gil
  • Chun Hean, Lee
  • Giacomini, Matteo
  • Bonet Carbonell, Javier
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This paper presents a new Updated Reference Lagrangian Smooth Particle Hydrodynamics (SPH) algorithm for the analysis of large deformation isothermal elasticity and elasto-plasticity. Taking as point of departure a Total Lagrangian setting and considering as referential configuration an intermediate configuration of the deformation process, the equation of conservation of linear momentum and three geometric conservation laws (for the deformation gradient, its cofactor and its determinant) are re-written leading to a very generic system of first order conservation laws. The key feature of the formulation is a suitable multiplicative decomposition of the conservation variables, leading to a very simple final set of equations with striking similarities to the conventional Total Lagrangian system albeit re-written in terms of alternative Referential Updated conservation variables which are evolved in time. Taking advantage of this new Updated Reference Lagrangian formalism, a second order entropy-stable SPH upwinding stabilisation method will be introduced. With respect to previous publications by the group, a new three-stage Runge–Kutta time integration method is implemented in order to increase the CFL stability restriction. Finally, and to demonstrate the robustness and applicability of the methodology, a wide spectrum of challenging problems will be presented and compared, including some benchmark three-dimensional large deformation elasto-plasticity problems. To facilitate its ease of implementation, the paper explores the use of a series of novel expressions for the evaluation of kernels and the gradients of kernels to provide the SPH user the freedom to choose amongst various options, all leading to equally convincingly robust results., The authors would like to acknowledge the financial support received through the project Marie SkłodowskaCurie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with Grant Number 764636. The third author also gratefully acknowledges the support provided by the EPSRC Strategic Support Package: Engineering of Active Materials by Multiscale/Multiphysics Computational Mechanics - EP/R008531/1. The fourth author acknowledges the support of the Serra Hunter Programme of the Generalitat de ´ Catalunya, the Spanish Ministry of Economy and Competitiveness (Grant agreement No. PID2020-113463RB-C33) and the Spanish Ministry of Economy and Competitiveness through the Severo Ochoa programme for centres of excellence in RTD (Grant agreement No. CEX2018-000797-S)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

An acoustic Riemann solver for large strain computational contact dynamics

  • Runcie, Callum J.
  • Lee, Chun Hean
  • Haider, Jibran
  • Gil, Antonio
  • Bonet Carbonell, Javier
This article presents a vertex-centered finite volume algorithm for the explicit dynamic analysis of large strain contact problems. The methodology exploits the use of a system of first order conservation equations written in terms of the linear momentum and a triplet of geometric deformation measures (comprising the deformation gradient tensor, its co-factor, and its Jacobian) together with their associated jump conditions. The latter can be used to derive several dynamic contact models ensuring the preservation of hyperbolic characteristic structure across solution discontinuities at the contact interface, a clear advantage over the standard quasi-static contact models where the influence of inertial effects at the contact interface is completely neglected. Taking advantage of the conservative nature of the formalism, both kinetic (traction) and kinematic (velocity) contact interface conditions are explicitly enforced at the fluxes through the use of appropriate jump conditions. Specifically, the kinetic condition is enforced in the usual linear momentum equation, whereas the kinematic condition can now be easily enforced in the geometric conservation equations without requiring a computationally demanding iterative algorithm. Additionally, a total variation diminishing shock capturing technique can be suitably incorporated in order to improve dramatically the performance of the algorithm at the vicinity of shocks. Moreover, and to guarantee stability from the spatial discretization standpoint, global entropy production is demonstrated through the satisfaction of semi-discrete version of the classical Coleman–Noll procedure expressed in terms of the time rate of the so-called Hamiltonian energy of the system. Finally, a series of numerical examples is examined in order to assess the performance and applicability of the algorithm suitably implemented in OpenFOAM. The knowledge of the potential contact loci between contact interfaces is assumed to be known a priori., Callum J. Runcie and Chun Hean Lee gratefully acknowledge the support provided by the EPSRC Strategic Support Package: Engineering of Active Materials by Multiscale/Multiphysics Computational Mechanics - EP/R008531/1. Antonio J. Gil and Chun Hean Lee would like to acknowledge the financial support received through the project Marie Skłodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with Grant number 764636. Callum J. Runcie and Chun Hean Lee would also like to acknowledge the many useful discussions with Dr. Peter Grassl from University of Glasgow., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A robust updated lagrangian smooth particle hydrodynamics for fast solid dynamics

  • Refachinho de Campos, Paulo Roberto
  • Antonio Javier, Gil
  • Chun Hean, Lee
  • Huerta, Antonio
  • Giacomini, Matteo
  • Bonet Carbonell, Javier
This paper introduces a new Incremental Updated Lagrangian Smooth Particle Hydrodynamics (SPH) computational framework in the form of a system of first order conservation laws. Specifically, the linear momentum conservation equation is solved in an incremental manner in conjunction with a set of incremental geometric conservation laws for the minors of the deformation gradient tensor, namely the deformation gradient, its cofactor and its Jacobian. Taking advantage of this new formalism, an entropy-stable upwinding stabilisation SPH method is introduced, with no user-defined regularisation parameters involved. The resulting semi-discrete SPH equations are variationally consistent and also ensure the global production of numerical entropy, demonstrated through the semi-discrete version of the classical Coleman-Noll procedure. The overall methodology will be shown to be capable of handling large deformations without persistent numerical shortcomings often encountered in the classical SPH (displacement-based) formulation., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

An improved updated Lagrangian SPH method for structural modelling

  • Khayyer, Abbas
  • Shimizu, Yuma
  • Chun Hean, Lee
  • Gil Ruiz, Antonio Javier
  • Gotoh, Hitoshi
  • Bonet Carbonell, Javier
The version of record of this article, first published in Computational particle mechanics, is available online at Publisher’s website: https://doi.org/10.1007/s40571-023-00673-z, This paper presents a set of novel refined schemes to enhance the accuracy and stability of the updated Lagrangian SPH (ULSPH) for structural modelling. The original ULSPH structure model was first proposed by Gray et al. (Comput Methods Appl Mech Eng 190:6641–6662, 2001) and has been utilised for a wide range of structural analyses including metal, soil, rubber, ice, etc., although the model often faces several drawbacks including unphysical numerical damping, high-frequency noise in reproduced stress fields, presence of several artificial terms requiring ad hoc tunings and numerical instability in the presence of tensile stresses. In these regards, this study presents a set of enhanced schemes corresponding to (1) consistency correction on discretisation schemes for differential operators, (2) a numerical diffusive term incorporated in the continuity or the density rate equation, (3) tuning-free stabilising term based on Riemann solution and (4) careful control/switch of stress divergence differential operator model under tensile stresses. Qualitative/quantitative validations are conducted through several well-known benchmark tests., This study was supported by JSPS (Japan Society for the Promotion of Science) KAKENHI Grants Number JP21H01433, JP18K04368, JP21K14250 and JP22H01599. Antonio Gil and Chun Hean Lee would like to acknowledge the financial support received through the project Marie Sklodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with grant number 764636. The first author acknowledges the contribution of Mr. Kazuhiro Kinuta and Mr. Kazunori Yunoki, students of Applied Mechanics Laboratory, Kyoto University, in conducting several preliminary simulations corresponding to this study back in 2021 and 2022, respectively., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A face-centred finite volume method for laminar and turbulent incompressible flows

  • Vieira, Luan M.
  • Giacomini, Matteo
  • Sevilla, Rubén
  • Huerta, Antonio
This work develops, for the first time, a face-centred finite volume (FCFV) solver for the simulation of laminar and turbulent viscous incompressible flows. The formulation relies on the Reynolds-averaged Navier–Stokes (RANS) equations coupled with the negative Spalart–Allmaras (SA) model and three novel convective stabilisations, inspired by Riemann solvers, are derived and compared numerically. The resulting method achieves first-order convergence of the velocity, the velocity-gradient tensor and the pressure. FCFV accurately predicts engineering quantities of interest, such as drag and lift, on unstructured meshes and, by avoiding gradient reconstruction, the method is less sensitive to mesh quality than other FV methods, even in the presence of highly distorted and stretched cells. A monolithic and a staggered solution strategies for the RANS-SA system are derived and compared numerically. Numerical benchmarks, involving laminar and turbulent, steady and transient cases are used to assess the performance, accuracy and robustness of the proposed FCFV method., The authors acknowledge the support of: H2020 MSCA ITN-EJD ProTechTion (Grant No. 764636) that partially funded the PhD scholarship of LMV; Spanish Ministry of Science, Innovation and Universities and Spanish State Research Agency MICIU/AEI/10.13039/501100011 033 (Grants No. PID2020-113463RB-C33 to MG, PID2020-113463RBC32 to AH and CEX2018-000797-S to MG and AH); Generalitat de Catalunya, Spain (Grant No. 2021-SGR-01049 to MG and AH); MG is Fellow of the Serra Húnter Programme of the Generalitat de Catalunya., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Nonintrusive parametric solutions in structural dynamics

  • Cavaliere, Fabiola
  • Zlotnik, Sergio
  • Larráyoz Izcara, Xabier
  • Díez, Pedro
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, A nonintrusive reduced order method able to solve a parametric modal analysis is proposed in this work. The main objective is being able to efficiently identify how a variation of user-defined parameters affects the dynamic response of the structure in terms of fundamental natural frequencies and corresponding mode shapes. A parametric version of the inverse power method (IPM) is presented by using the proper generalised decomposition (PGD) rationale. The proposed approach utilises the socalled encapsulated PGD toolbox and includes a new algorithm for computing the square root of a parametric object. With only one offline computation, the proposed PGD-IPM approach provides an analytical parametric expression of the smallest (in magnitude) eigenvalue (or natural frequency) and corresponding eigenvector (mode shape), which contains all the possible solutions for every combination of the parameters within pre-defined ranges. A Lagrange multiplier deflation technique is introduced in order to compute subsequent eigenpairs, which is also valid to overcome the stiffness matrix singularity in the case of a free-free structure. The proposed approach is nonintrusive and it is therefore possible to be integrated with commercial finite element (FE) packages. Two numerical examples are shown to underline the properties of the technique. The first example includes one material and one geometric parameter. The second example shows a more realistic industrial example, where the nonintrusivity of the approach is demonstrated by employing a commercial FE package for assembling the FE matrices. Finally, a multi-objective optimisation study is performed proving that the developed method could significantly assist the decision-making during the preliminary phase of a new design process., This project is part of the Marie Skłodowska-Curie ITN-EJD ProTechTion funded by the European Union Horizon 2020 research and innovation program with Grant Number 764636. The work of Fabiola Cavaliere, Sergio Zlotnik and Pedro Díez is partially supported by the MCIN/AEI/10.13039/501100011033, Spain (Grant Number: PID2020-113463RB-C32, PID2020-113463RB-C33 and CEX2018-000797-S). Ruben Sevilla also acknowledges the support of the Engineering and Physical Sciences Research Council (Grant Number: EP/P033997/1)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Nonintrusive parametric NVH study of a vehicle body structure

  • Cavaliere, Fabiola
  • Zlotnik, Sergio
  • Sevilla Càrdenas, Ruben
  • Larráyoz Izcara, Xabier
  • Díez, Pedro
This is an Accepted Manuscript of an article published by Taylor & Francis Group in Mechanics based design of structures and machines on 27/06/22, available online at: http://www.tandfonline.com/10.1080/15397734.2022.2098140, A reduced order model technique is presented to perform the parametric Noise, Vibration and Harshness (NVH) study of a vehicle body-in-white (BIW) structure characterized by material and shape design variables. The ultimate goal is to develop a methodology which allows to efficiently explore the variation in the design space of the BIW static and dynamic global stiffnesses, such that the NVH performance can be evaluated already in the preliminary phase of the development process. The proposed technique is based on the proper generalized decomposition (PGD) method. The obtained PGD solution presents an explicit dependency on the introduced design variables, which allows to obtain solutions in 0.1 milliseconds and therefore opens the door to fast optimization studies and real-time visualizations of the results in a pre-defined range of parameters. The method is nonintrusive, such that an interaction with commercial software is possible. A parametrized finite element (FE) model of the BIW is built by means of the ANSA CAE preprocessor software, which allows to account for material and geometric parameters. A comparison between the parametric NVH solutions and the full-order FE simulations is performed using the MSC-Nastran software, to validate the accuracy of the proposed method. In addition, an optimization study is presented to find the optimal materials and shape properties with respect to the NVH performance. Finally, in order to support the designers in the decision-making process, a graphical interface app is developed which allows to visualize in real-time how changes in the design variables affect pre-defined quantities of interest., This project is part of the Marie Skłodowska-Curie ITN-EJD ProTechTion funded by the European Union Horizon 2020 research and innovation program with Grant Number 764636. The work of Fabiola Cavaliere, Sergio Zlotnik and Pedro D ıez is partially supported by the MCIN/AEI/10.13039/501100011033, Spain (Grant Number: PID2020-113463RB-C32, PID2020-113463RB-C33 and CEX2018-000797-S). Ruben Sevilla also acknowledges the support of the Engineering and Physical Sciences Research Council (Grant Number: EP/T009071/1)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Discrete empirical interpolation for hyper-reduction of hydro-mechanical problems in groundwater flow through soil

  • Nasika, Christina
  • Díez, Pedro
  • Gerard, Pierre
  • Massart, Thierry J.
  • Zlotnik, Sergio
This is the peer reviewed version of the following article: Nasika, C. [et al.]. Discrete empirical interpolation for hyper-reduction of hydro-mechanical problems in groundwater flow through soil. "International journal for numerical and analytical methods in geomechanics", 10 Abril 2023, vol. 47, núm. 5, p. 667-693, which has been published in final form at https://onlinelibrary.wiley.com/doi/10.1002/nag.3487. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Use of Self-Archived Versions. This article may not be enhanced, enriched or otherwise transformed into a derivative work, without express permission from Wiley or by statutory rights under applicable legislation. Copyright notices must not be removed, obscured or modified. The article must be linked to Wiley’s version of record on Wiley Online Library and any embedding, framing or otherwise making available the article or pages thereof by third parties from platforms, services and websites other than Wiley Online Library must be prohibited., The recent surge in the availability of sensor data and computational resources has fostered the development of technologies for optimization, control, and monitoring of large infrastructures, integrating data and numerical modeling. The major bottleneck in this type of technologies is the model response time, since repetitive solutions are typically required. To reduce the computational time, reduced order models (ROMs) are used as surrogates for expensive finite element (FE) simulations enabling the use of complex models in this type of applications. In this work, ROMs are explored for the solution of the fully coupled hydro-mechanical system of equations that governs the water flow through partially saturated soil. The POD-based Reduced Basis Method and the Discrete Empirical Interpolation Method (DEIM), as well as its localized version (LDEIM), are examined in solving a parametrized problem simulating the mechanical loading of an embankment dam. Hydraulic and mechanical soil properties are considered as parameters. It is shown that the combination of these methods results in simulations that require 1/10 to 1/100 of the FE response time. Moreover, the method is shown to yield scaling efficiency gains with increasing problem size., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A first-order hyperbolic arbitrary Lagrangian Eulerian conservation formulation for non-linear solid dynamics

  • Giusto, Thomas di
  • Chun Hean, Lee
  • Antonio Javier, Gil
  • Bonet Carbonell, Javier
  • Giacomini, Matteo
The paper introduces a computational framework using a novel Arbitrary Lagrangian Eulerian (ALE) formalism in the form of a system of first-order conservation laws. In addition to the usual material and spatial configurations, an additional referential (intrinsic) configuration is introduced in order to disassociate material particles from mesh positions. Using isothermal hyperelasticity as a starting point, mass, linear momentum and total energy conservation equations are written and solved with respect to the reference configuration. In addition, with the purpose of guaranteeing equal order of convergence of strains/stresses and velocities/displacements, the computation of the standard deformation gradient tensor (measured from material to spatial configuration) is obtained via its multiplicative decomposition into two auxiliary deformation gradient tensors, both computed via additional first-order conservation laws. Crucially, the new ALE conservative formulation will be shown to degenerate elegantly into alternative mixed systems of conservation laws such as Total Lagrangian, Eulerian and Updated Reference Lagrangian. Hyperbolicity of the system of conservation laws will be shown and the accurate wave speed bounds will be presented, the latter critical to ensure stability of explicit time integrators. For spatial discretisation, a vertex-based Finite Volume method is employed and suitably adapted. To guarantee stability from both the continuum and the semi-discretisation standpoints, an appropriate numerical interface flux (by means of the Rankine–Hugoniot jump conditions) is carefully designed and presented. Stability is demonstrated via the use of the time variation of the Hamiltonian of the system, seeking to ensure the positive production of numerical entropy. A range of three dimensional benchmark problems will be presented in order to demonstrate the robustness and reliability of the framework. Examples will be restricted to the case of isothermal reversible elasticity to demonstrate the potential of the new formulation., The first, second and third authors would like to acknowledge the financial support received through the project MarieSkłodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation programwith grant number 764636. Chun Hean Lee acknowledges the support provided by the EPSRC Strategic Support Package:Engineering of Active Materials by Multiscale/Multiphysics Computational Mechanics–EP/R008531/1. Antonio J. Gilacknowledges the support provided by UK AWE via project PO 40062030. Javier Bonet acknowledges the financial supportreceived via project POTENTIAL (PID2022-141957OB-C21) funded by MCIN/AEI/10.13039/501100011033/FEDER, UE.Matteo Giacomini acknowledges the Spanish Ministry of Science and Innovation and Spanish State Research AgencyMCIN/AEI/10.13039/501100011033 (Grant nos. PID2020-113463RB-C33 and CEX2018-000797-S). Matteo Giacomini isFellow of the Serra Húnter Programme of the Generalitat de Catalunya., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Phase distribution and properties identification of heterogeneous materials: a data-driven approach

  • Valdés Alonzo, Gabriel Rolando
  • Binetruy, Christophe
  • Eck, Benedikt
  • García González, Alberto
  • Leygue, Adrien
© 2022 Elsevier. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This paper presents a new methodology to extend the Data-Driven Identification (DDI) to heterogeneous samples made of multiple elastic materials. By using the Correspondence Analysis (CA) technique to post-process DDI, we are able to identify multiple material databases representative of the material behavior of each phase. Simultaneously, we localize the different phases (matrix and inclusions) in the sample. For different contrasts between phases, the method is tested on synthetically generated data and a parametric study is performed. Furthermore, we show that it is possible to iterate between DDI and CA in order to improve the method’s predictions when it is limited by scarce input data. In all the cases studied, the methodology proves to be effective for estimating stresses, as well as for identifying the different phases in the sample., This project is part of the Marie Sklodowska-Curie ITN-EJD ProTechTion funded by the European Union Horizon 2020 research and innovation program with Grant Number 764636., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

An acoustic Riemann solver for large strain computationalcontact dynamics

  • Runcie, Callum J.
  • Lee, Chun Hean
  • Haider, Jibran
  • Gil, Antonio J.
  • Bonet Carbonell, Javier
This article presents a vertex-centered finite volume algorithm for the explicit dynamic analysis of large strain contact problems. The methodology exploits the use of a system of first order conservation equations written in terms of the linear momentum and a triplet of geometric deformation measures (comprising the deformation gradient tensor, its co-factor, and its Jacobian) together with their associated jump conditions. The latter can be used to derive several dynamic contact models ensuring the preservation of hyperbolic characteristic structure across solution discontinuities at the contact interface, a clear advantage over the standard quasi-static contact models where the influence of inertial effects at the contact interface is completely neglected. Taking advantage of the conservative nature of the formalism, both kinetic (traction) and kinematic (velocity) contact interface conditions are explicitly enforced at the fluxes through the use of appropriate jump conditions. Specifically, the kinetic condition is enforced in the usual linear momentum equation, whereas the kinematic condition can now be easily enforced in the geometric conservation equations without requiring a computationally demanding iterative algorithm. Additionally, a total variation diminishing shock capturing technique can be suitably incorporated in order to improve dramatically the performance of the algorithm at the vicinity of shocks. Moreover, and to guarantee stability from the spatial discretization standpoint, global entropy production is demonstrated through the satisfaction of semi-discrete version of the classical Coleman–Noll procedure expressed in terms of the time rate of the so-called Hamiltonian energy of the system. Finally, a series of numerical examples is examined in order to assess the performance and applicability of the algorithm suitably implemented in OpenFOAM. The knowledge of the potential contact loci between contact interfaces is assumed to be known a priori., Antonio J. Gil and Chun Hean Lee would like to acknowledge the financial support received through the project Marie Skłodowska-Curie ITN-EJD ProTechTion, funded by the European Union Horizon 2020 research and innovation program with Grant number 764636. Callum J., Peer Reviewed, Postprint (published version)