Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 17
Encontrada(s) 1 página(s)

DIGITAL.INTA Repositorio Digital del Instituto Nacional de Técnica Aeroespacial
Publicación Artículo científico (JournalArticle)

Laboratory intercomparison of solar absorptance and thermal emittance measurements at room temperature

  • Caron, Simon
  • Herding, L.
  • Binyamin, Yaniv
  • Baidossi, M.
  • Vinetsky, Y.
  • Morales, Angel
  • Hildebrandt, C.
  • Reoyo Prats, R.
  • Faugeroux, O.
  • Sutter, Florian
  • Röger, M.
  • Manzano Agugliaro, F.
  • Agüero, Alina
  • Sergio, Rodríguez Catela
Solar thermal absorber coatings play an important role in the opto-thermal efficiency of receivers in Concentrated Solar Power (CSP). Two standard figures of merit are the solar absorptance αsol and thermal emittance εth, derived from spectral directional hemispherical reflectance measurements at room temperature. These two figures of merit allow comparing coating formulations in terms of performance and durability. In this study, a black coating and a solar selective coating are optically characterized by different laboratories to compare spectral datasets, solar absorptance αsol and thermal emittance εth calculations. The comparison includes various benchtop spectrophotometers operating in the UV-VIS-NIR and Infrared spectral ranges as well as three commercial portable reflectometers/emissometers. A good agreement is found between the nine parties participating in this intercomparison campaign. The black coating αsol value is 96.6 ± 0.2%, while the solar selective coating αsol value is 94.5 ± 0.4%. For the thermal emittance, spectral data is concatenated and integrated from 0.3 to 16 μm. The black coating εth value calculated at 650 °C is 80.8 ± 3.8%, while the solar selective coating εth value calculated at 650 °C is 25.0 ± 0.5%., Financial support from the European Union is gratefully acknowledged (EU-Raiselife project, Horizon 2020, Contract n° 686008). The author thanks the OPAC laboratory technical staff: Lucia Martinez, Carmen Amador and Tomas Reche for their technical assistance in optical measurements. This project (EU SFERA-III) has received funding from the European Union’s Horizon 2020 Research and Innovation Program under grant agreement n◦ 823802, Peerreview
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Heliostat field aiming strategy based on deterministic optimization: An experimental validation

  • Sánchez González, Alberto
  • Kontopyrgos, Marios
  • Milidonis, Kypros
  • Georgiou, Marios C.
In Solar Power Tower plants, the aiming strategy plays a key role in the performance and interaction between heliostat field and receiver. This work presents an aiming strategy based on a deterministic optimization that maximizes the flux uniformity and minimizes the spillage losses. The algorithm can be fed either by a flux mapping model or by the synthesis - superposition - of experimental images. Both approaches are experimentally tested at PROTEAS research facility, aiming 16 heliostats at a flat Lambertian target. In the comparison between experimental and computed flux maps, the cross-correlation coefficient exceeds 97%. The spillage loss factors are underestimated by the computations: 9.2 percentage points by the model-based and 6.7 points by the synthesis-based approach., A. Sánchez-González thanks the Cyprus Institute for providing access to its installations, the support of its scientific and technical staff, and the financial support of the SFERA-III project (Grant Agreement No. 823802). This work has been supported by the Madrid Government (Comunidad de Madrid - Spain) under the Multiannual Agreement with UC3M (SOLAROPIA-CM-UC3M). Funding for APC: Universidad Carlos III de Madrid (Agreement CRUE-Madroño 2024).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Computation of canting errors in heliostats by flux map fitting: experimental assessment

  • Sánchez González, Alberto
  • Grange, Benjamin
  • Caliot, Cyril
In solar tower plants, thousands of heliostats reflect sunlight into a central receiver. Heliostats consist of a subset of mirrors called facets that must be perfectly oriented (i.e., canted) to concentrate as much solar radiation as possible. This study presents and validates the so-called flux map fitting technique to detect and correct canting errors. The computed distributions were matched to a series of images through an optimization algorithm. According to the sensitivity analysis, three images spread along a single day provide sufficient information for the algorithm to succeed. Using this methodology, four heliostats at the THEMIS research facility were recanted, thereby substantially increasing the optical quality in three of them. The procedure to infer the heliostat aimpoint was assessed., Universidad Carlos III de Madrid (2020/00051); European Commission (823802); Horizon 2020 Framework Programme (727762). We thank the CNRS-PROMES laboratory, UPR 8521, belonging to the French National Center for Scientific Research (CNRS), for providing access to its facilities, the support of its scientific and technical staff, and the financial support of the SFERA-III project (Grant Agreement No. 823802). We thank the technical help provided by Yann Volut, William Baltus, and Antoine Pérez. The research project VISHELIO-CM-UC3M has been funded by the call "Programa de apoyo a la realización de proyectos interdisciplinares de I+D para jóvenes investigadores de la Universidad Carlos III de Madrid 2019-2020" under the framework of the "Convenio Plurianual Comunidad de Madrid-Universidad Carlos III de Madrid". This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No. 727762, project acronym NEXT-CSP., Publicado
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Experimental Devices to Investigate the Long-Term Stability of Phase Change Materials under Application Conditions

  • Rathgeber, Christoph
  • Hiebler, Stefan
  • Bayón, Rocío
  • Cabeza, Luisa F.
  • Zsembinszki, Gabriel
  • Englmair, Gerald
  • Dannemand, Mark
  • Diarce Belloso, Gonzalo
  • Fellmann, Oliver
  • Ravotti, Rebecca
  • Groulx, Dominic
  • Kheirabadi, Ali C.
  • Gschwander, Stefan
  • Höhlein, Stephan
  • König Haagen, Andreas
  • Beaupere, Noé
  • Zalewski, Laurent
An important prerequisite to select a reliable phase change material (PCM) for thermal energy storage applications is to test it under application conditions. In the case of solid–liquid PCM, a large amount of thermal energy can be stored and released in a small temperature range around the solid–liquid phase transition. Therefore, to test the long-term stability of solid–liquid PCM, they are subjected to melting and solidification processes taking into account the conditions of the intended application. In this work, 18 experimental devices to investigate the long-term stability of PCM are presented. The experiments can be divided into thermal cycling stability tests, tests on PCM with stable supercooling, and tests on the stability of phase change slurries (PCS). In addition to these experiments, appropriate methods to investigate a possible degradation of the PCM are introduced. Considering the diversity of the investigated devices and the wide range of experimental parameters, further work toward a standardization of PCM stability testing is recommended., This survey has been carried out within the framework of IEA ES Annex 33/SHC Task 58 “Material and Component Development for Compact Thermal Energy Storage”, a joint working group of the “Energy Storage” (ES) and the “Solar Heating and Cooling” (SHC) Technology Collaboration Programmes of the International Energy Agency (IEA). The responsibility for the content of this publication is with the authors. The work of ZAE Bayern is part of the project properPCM and was supported by the German Federal Ministry of Economic Affairs and Energy under the project code 03ET1342A. The work of CIEMAT is part of two projects: ACES2030 (S2018/EM-4319) which is supported by Comunidad de Madrid and European Structural Funds through and SFERA III (GA No 823802) which is supported by European Union’s Horizon H2020 Research and Innovation Programme. The work of DTU was supported by HM Heizkörper GmbH and the Danish Energy Agency through the EUDP program. The work of EHU is part of the project Sweet-TES (RTI2018-099557-B-C22), funded by the Spanish Ministry of Science, Innovation and Universities. The work of GREiA was partially funded by the Ministerio de Ciencia, Innovación y Universidades de España (RTI2018-093849-B-C31—MCIU/AEI/FEDER, UE) and by the Ministerio de Ciencia, Innovación y Universidades—Agencia Estatal de Investigación (AEI) (RED2018-102431-T). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (GREiA 2017 SGR 1537). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme. The work of HSLU was partially funded by the Swiss Competence Centre for Energy Research on Heat and Electricity (SCCER HaE). The authors would like to thank the SCCER HaE as well as METTLER TOLEDO AG for the support given. The work of Fraunhofer ISE was part of the projects KOLAN (FKZ 03ESP357B) and KOKAP (FKZ 03ET1463A) which were administrated by the Projektträger Jülich (PtJ) and funded by the German Federal Ministry of Economic Affairs and Energy. The work of LAMTE was supported by Intel Corporation, along with the Natural Sciences and Engineering Research Council of Canada (NSERC) and the Canada Foundation for Innovation. The work of LGCgE is partly funded by the French National Research Agency (ANR) under the project "Hybrid storage and heat exchanger device with PCM—EUROPA". Noé Beaupere’s PhD work was funded by the French Alternative Energies and Atomic Energy Commission (CEA) Grenoble. The work of LTTT is part of the project MALATrans and was funded by the German Federal Ministry for Economic Affairs and Energy (BMWi) under the project code 03ESP227B.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Finding the Limits of Magnetic Hyperthermia on Core-Shell Nanoparticles Fabricated by Physical Vapor Methods

  • Martínez Boubeta, Carlos
  • Simeonidis, Konstantinos
  • Oró, Judith
  • Makridis, Antonios
  • Serantes, David
  • Balcells, Lluis
Magnetic nanoparticles can generate heat when exposed to an alternating magnetic field. Their heating efficacy is governed by their magnetic properties that are in turn determined by their composition, size and morphology. Thus far, iron oxides (e.g., magnetite, Fe3O4) have been the most popular materials in use, though recently bimagnetic core-shell structures are gaining ground. Herein we present a study on the effect of particle morphology on heating efficiency. More specifically, we use zero waste impact methods for the synthesis of metal/metal oxide Fe/Fe3O4 nanoparticles in both spherical and cubic shapes, which present an interesting venue for understanding how spin coupling across interfaces and also finite size effects may influence the magnetic response. We show that these particles can generate sufficient heat (hundreds of watts per gram) to drive hyperthermia applications, whereas faceted nanoparticles demonstrate superior heating capabilities than spherical nanoparticles of similar size., We thank the CNRS-PROMES laboratory, UPR 8521, belonging to the French National Centre for Scientific Research (CNRS) for providing access to its installations, the support of its scientific and technical staff (N. Boullet, E. Guillot, A. Badziaka), and the financial support of the SFERA-III project (Grant Agreement No 823802). Spanish Ministry of Science, Innovation and Universities through grant (CEX2019-000917-S) in the framework of the Spanish Severo Ochoa Centre of Excellence Program and RTI2018-099960-B-I00 (SPINCURIOX). This research is cofinanced by Greece and the European Union (European Social Fund-ESF) through the Operational Programme “Human Resources Development, Education and Lifelong Learning” in the context of the project “Reinforcement of Postdoctoral Researchers—2nd Cycle” (MIS-5033021), implemented by the State Scholarships Foundation (IKΥ)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Solar dissociation of zirconium silicate sand: A clean alternative to obtain zirconium dioxide

  • Fernández-González, Daniel
  • Piñuela-Noval, Juan
  • Ruiz-Bustinza, Íñigo
  • González-Gasca, Carmen
  • Gómez-Rodríguez, Cristian
  • García-Quiñonez, Linda Viviana
  • Fernández, Adolfo
  • Verdeja, Luis Felipe
Application of concentrated solar energy (CSE) in the industry of materials is a promising alternative that is developing in recent years to reduce the environmental impact while accomplishing the objective of producing high-quality products. It is important to enlarge the processes being studied with the competition of CSE to find the most attractive for the scalation up to the industrial level and thus contributing to the energy transition in the field of materials. Systematic laboratory research has been conducted within the thermal decomposition of metal carbonates, sulphates, hydroxides, and metal oxides with promising results using CSE, which has the competing advantage of heat production without releasing pollutants and the construction of the installation as principal cost. Nevertheless, the thermal decomposition of zirconium silicate (ZrSiO4), despite of the importance of zirconium dioxide in the field of ceramics and the high energy consumption in the process, has never been reported in the literature using CSE. The process proposed in this manuscript consists of two stages, the pyrometallurgical one, based on the direct application of CSE to ZrSiO4 to dissociate it into ZrO2 and SiO2, and the hydrometallurgical one, based on the aqueous extraction of the zirconium dioxide with NaOH at 200 °C for 6 h in pressure reactor. The double-stage process based on CSE leads to the synthesis of close to 95% purity monoclinic ZrO2. The energy for the pyrometallurgical route is supplied by a renewable energy source (CSE), thus contributing to reduce carbon dioxide emissions in the synthesis of ZrO2., Daniel Fernández-González acknowledges the grant (Juan de la Cierva-Formación program) FJC2019-041139-I funded by MCIN/AEI/10.13039/501100011033 (Ministerio de Ciencia e Innovación, Agencia Estatal de Investigación). Juan Piñuela Noval acknowledges the Programa “Severo Ochoa” of Grants for Research and Teaching of the Principality of Asturias for the funds received for the elaboration of the Ph. D. Thesis (Ref: BP20 041). We thank the PROMES-CNRS (PROcédés Matériaux et Energie Solaire- Centre National de la Recherche Scientifique) for providing access to its installations, the support of its scientific and technical staff, and the financial support of the SFERA-III project (Grant Agreement No 823802)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Solar assisted production of MgAl2O4 from Bayer process electrofilter fines as source of Al2O3

  • Fernández-González, Daniel
  • Piñuela-Noval, Juan
  • Ruiz-Bustinza, Íñigo
  • González-Gasca, Carmen
  • Gómez-Rodríguez, Cristian
  • García-Quiñonez, Linda Viviana
  • López-Liévano, Adolfo
  • Fernández, Adolfo
  • Verdeja, Luis Felipe
Compared with conventional high-temperature methods based on electricity and fossil fuels, concentrated solar energy route offers distinct advantages in terms of mitigating emissions of contaminants and shortening processing times. Nevertheless, solar-based route also encounters challenges in producing significant quantities of materials, although the deployment of this technology is still conditioned by the limited investigation in the field. This study presents a novel high-temperature process based on solar energy to produce MgAl2O4 spinel, which employs as source of Al2O3 a waste from the aluminum industry: waste alumina fines from the Bayer process. First, mixtures were prepared by mechanical mixing in a molar ratio 1:1 in agreement with the MgO–Al2O3 binary phase diagram. Then, synthesis of the MgAl2O4 spinel was conducted by static experiments (5 min) with direct application of concentrated solar energy (1150 W/cm2) at temperatures greatly exceeding 1800 °C as reported by ANSYS software. Wastes from three Bayer process factories were studied, which exhibited after the synthesis process a good crystallinity. The carbon dioxide emissions avoidance would range from the 200 to 500 tons of CO2/year in the case of a small plant producing 1000 tons/year to 5000 to 12,000 tons of CO2/year in the case of a commercial plant producing 25,000 tons/year, thus contributing to mitigate climate change. The proposed process might lead to smaller volume of wastes in the aluminum industry, while the MgAl2O4 may be used as raw material in the numerous fields based on the chemical, thermal, dielectric, mechanical and optical properties., Daniel Fernández-González acknowledges the grant (Juan de la Cierva-Formación program) FJC2019-041139-I funded by the Ministerio de Ciencia e Innovación, Agencia Estatal de Investigación. Juan Piñuela Noval acknowledges the Programa “Severo Ochoa” of Grants for Research and Teaching of the Principality of Asturias for the funds received for the elaboration of the Ph. D. Thesis (Ref: BP20 041). We thank the PROMES-CNRS (PROcédés Matériaux et Energie Solaire- Centre National de la Recherche Scientifique) for providing access to its installations, the support of its scientific and technical staff, and the financial support of the SFERA-III project (Grant Agreement No 823802)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Implications of renewable energy sources in metallurgy: Utilization of concentrated solar energy in recycling metallurgical wastes

  • Fernández-González, Daniel
  • Piñuela-Noval, Juan
  • Gómez-Rodríguez, Cristian
  • Fernández-Valdés, Adolfo
  • Verdeja, Luis Felipe
Solar energy, when it is concentrated, can reach temperatures as high as 3000 °C and generate heat without producing pollutants such as carbon dioxide or other harmful agents. Additionally, solar energy is virtually free and can be utilized in remote areas not connected to the electrical grid. However, slags, a by-product of metallurgical industries, are not commonly used due to the cost of processing them. This manuscript proposes studying the use of concentrated solar energy to extract metals from four types of slags: basic oxygen furnace (BOF) slag, copper slag, silicomanganese slag, and ferromanganese slag, each containing important metals. Experimental work at the Odeillo solar furnace suggests that iron oxides in the BOF slag transform into magnetic phases, while copper slag experiences changes in fayalite (that partially transforms into magnetite) and copper oxides and sulfides (that also convert into metallic copper nodules). The ferromanganese and silicomanganese slags become more refractory, making the extraction of manganese more challenging. Overall, the study suggests that at least part of the metals might be collected in a usable form., We thank the PROMES-CNRS (PROcédés Matériaux et Energie Solaire- Centre National de la Recherche Scientifique) for providing access to its installations, the support of its scientific and technical staff, and the financial support of the SFERA-III project (Grant Agreement No 823802). Juan Piñuela Noval acknowledges the Programa “Severo Ochoa” of Grants for Research and Teaching of the Principality of Asturias for the funds received for elaborating the Ph. D. Thesis (Ref: BP20 041)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Production of calcium and magnesium titanates using concentrated solar energy

  • Fernández-González, Daniel
  • Piñuela-Noval, Juan
  • Gómez-Rodríguez, Cristian
  • Fernández, Adolfo
  • García-Quiñonez, Linda Viviana
  • Díaz, Luis A.
  • Verdeja, Luis Felipe
Solar energy is an adequate technology for different processes in metallurgy, materials processing, recycling, or ceramic-refractory materials, because of the high temperatures attained which are reached when the solar radiation is concentrated. This growing interest has also emerged from the obtaining of such temperatures without releasing pollutants such as carbon dioxide, SOx, NOx, or dioxins. Other benefits associated with concentrated solar energy are that this energy source is virtually free and the possibility of operating in places isolated from the electrical grid. Therefore, this research proposes the integration of concentrated solar energy in the production of calcium and magnesium titanates, which are materials with increasing demand in the field of electric components. Experimental work was carried out in the Odeillo solar furnace located in Font-Romeu-Odeillo-Via (France) using a 1.5-meter parabolic concentrator and mixtures of CaO and TiO2 and MgO and TiO2 in 1:1 molar ratio. Mixtures were subjected to values of incident radiation exceeding 900 W/m2 without using any special atmosphere and in very short times, which did not surpass 10 min. X-ray diffraction technique was employed to confirm the formation of the CaTiO3 and MgTiO3 perovskites. Therefore, concentrated solar energy might be a novel, fast, and environmentally sustainable manner of producing calcium and magnesium titanates., The authors of the manuscript want to express their gratitude to the project “Lead-free Piezoceramics by Low-Temperature Sintering: Energy effective and environmentally sustainable processing – Spark Plasma Sintering” (PID2021–128548OB-C22) project funded by the Spanish Ministerio de Ciencia e Innovación (MCIN) and Agencia Estatal de Investigación (AEI, MCIN/AEI/10.13039/501100011033). Juan Piñuela Noval acknowledges the Programa “Severo Ochoa” of Grants for Research and Teaching of the Principality of Asturias for the funds received for elaborating the pH. D. Thesis (Ref: BP20 041). We thank the PROMES-CNRS (PROcédés Matériaux et Energie Solaire- Centre National de la Recherche Scientifique) for providing access to its installations, the support of its scientific and technical staff, and the financial support of the SFERA-III project (Grant Agreement No 823802)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal shock resistance of additive manufactured Inconel 718 by concentrated solar energy

  • Damborenea, Juan de
  • Conde del Campo, Ana
  • Rodriguez-Donoso, Gloria
  • Agulló-Rueda, Fernando
  • Arenas, M. A.
Concentrated Solar Power (CSP) is a powerful tool for simulating the extreme high-temperature conditions that metallic materials encounter. Using a vertical parabolic solar furnace, it was possible to perform heating and cooling cycles between 250 and 950 °C in approximately 250 s per cycle. This capability is particularly relevant for the development of solar receivers used in solar thermal plants. Additive Manufacturing (AM) offers the potential to create new compositions and geometries that can enhance the efficiency of these solar receivers. In this study, Ni-base superalloys—identified as suitable materials for high-temperature solar receivers—were produced using AM and tested in two conditions: as-built and after thermal treatment. These were compared with a forged reference alloy. The results revealed the formation of a protective oxide layer on the surface in all cases. However, the oxide layer on the samples fabricated by additive manufacturing appeared to be more compact and adherent compared to that formed on the reference alloy., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This project (SURPF1904050070) has been partially funded from the European Union’s Horizon 2020 Research and Innovation Programme, under agreement no. 823802 (SFERA-III), which has facilitated access to the PROcédés Matériaux et Energie Solaire laboratories belonging to the French National Centre for Scientific Research (PROMES—CNRS).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Scaled-up graphene oxide membranes: Improved membrane distillation performance and antifouling properties

  • Skuse, Clara
  • Aparicio, Fernando
  • Andrés-Mañas, Juan Antonio
  • Zaragoza, Guillermo
  • Gallego-Schmid, Alejandro
  • Azapagic, Adisa
  • Lewthwaite, Katie
  • Gorgojo, Patricia
Membrane distillation (MD) is a promising desalination technology whose commercial implementation remains limited by high thermal energy consumption and membrane fouling. In this work, thermally efficient graphene oxide (GO)-functionalised membranes were fabricated and evaluated at pilot scale for the first time. Polyvinylidene fluoride (PVDF) membranes coated with polydopamine (PDA) and spray-coated with GO were tested in air-gap and vacuum-assisted air-gap MD (AGMD and V-AGMD) systems producing up to 1.5 L h⁻¹ of potable water. Membrane performance was evaluated in terms of permeate flux, salt rejection, antifouling behaviour and thermal efficiency using synthetic seawater, brine, foulant-containing feedwater and real seawater., The GO-PDA/PVDF membranes resisted fouling-induced pore wetting for over 72 h, compared with 20 h for pristine PVDF membranes. The GO coating reduced the fouling rate from 0.24%/h for the PDA/PVDF control membrane to 0.07%/h and enabled complete flux recovery (FRR = 100%) following a 30-minute rinse with deionised water at 75 °C, indicating fully reversible fouling. By comparison, the PDA/PVDF membrane exhibited an FRR of 87%. Experiments using real seawater also demonstrated stable operation and a 25% higher permeate flux relative to the control membrane., The GO-functionalised membranes also exhibited enhanced thermal performance, with up to 40% higher thermal efficiency and reductions in STEC of 16.7% and 9.8% for AGMD and V-AGMD, respectively. These findings demonstrate the potential of scalable GO coatings to improve the operational and energetic performance of MD desalination systems., The authors are grateful to the EPSRC for funding under grant number EP/S032258/1. Clara Skuse would like to acknowledge the EPSRC for funding this work through the NOWNANO CDT, and the EU Horizon 2020 research and innovation programme “Solar Facilities for the European Research Area - Third Phase’ — ‘SFERA-III” project for access to EU research installations (Grant Agreement n. 823802). Patricia Gorgojo acknowledges her Ramón y Cajal fellowship RYC2019–027060-I funded by MICIN/AEI/10.13039/501100011033 and by “ESF Investing in your future”., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Enhanced equivalent model algorithm for solar mirrors

  • Montecchi, M.
  • Sutter, F.
  • Fernández-García, A.
  • Heimsath, A.
  • Torres, F.
  • Pelayo, C.
The SolarPACES Reflectance Guideline provides an essential tool to obtain comparable reflectance measurements, but because of the lack of adequate commercial instrumentation, till now the exhaustive characterization of reflectance behaviour versus incidence ¿i and (half) acceptance angle ¿ is unachieved. An expert group in Task III has been working to outline some practicable solutions. The Equivalent Model Algorithm (EMA) was found quite promising: with few input data, EMA allows to predict any reflectance feature by computation. The recent availability of reliable reflectance measurements at oblique incidence made possible the refinement of EMA by analysing a representative set of commercial solar mirrors. This paper describes the new EMA for solar mirror, named EMA4SM, and reports its validation.
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Solar dissociation of zirconium silicate sand: A clean alternative to obtain zirconium dioxide

  • Fernández González, Daniel|||0000-0001-6957-4764
  • Piñuela Noval, Juan
  • Ruiz Bustinza, Íñigo|||0000-0002-8571-1105
  • González Gasca, Carmen|||0000-0003-0339-9910
  • Gómez Rodríguez, Cristian
  • García Quiñonez, Linda Viviana
  • Fernández, Juan|||0000-0002-8742-4572
  • Verdeja, Luis Felipe|||0000-0002-2392-2089
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Solar Assisted Production of MgAl2O4 from Bayer Process Electrofilter Fines as Source of Al2O3

  • Fernández González, Daniel|||0000-0001-6957-4764
  • Piñuela Noval, Juan
  • Ruiz Bustinza, Íñigo|||0000-0002-8571-1105
  • González Gasca, Carmen|||0000-0003-0339-9910
  • Gómez Rodríguez, Cristian
  • García Quiñonez, Linda Viviana
  • López Liévano, Adolfo
  • Fernández, Adolfo
  • Verdeja González, Luis Felipe
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Scaling-up the use of macroscopic photo-CWPO La1-xTixFeO3/SiC alveolar foam catalyst for solar water treatment against micropollutants

  • Garcia Muñoz, Patricia|||0000-0001-6157-7952
  • Abega, Aimé
  • Hernández-Zanoletty, Alba|||0000-0001-7868-4658
  • Robert, Didier
  • Malato, Sixto|||0000-0002-8085-4318
  • Keller, Nicolas|||0000-0003-1965-2730
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Characterization by key performance indicators of SFERA-III project to ALTAYR packed-bed prototype

  • Rojas, Esther
  • Alonso Romero, Elisa|||0000-0001-9676-095X
  • Rodríguez García, Margarita
  • Bayón, Rocío|||0000-0001-6646-7840
  • Avila-Marín, Antonio
RUO. Repositorio Institucional de la Universidad de Oviedo
Publicación Artículo científico (JournalArticle)

Solar assisted production of mgal2o4 from bayer process electrofilter fines as source of al2o3

  • Fernández González, Daniel|||0000-0001-6957-4764
  • Piñuela Noval, J.
  • Ruiz Bustinza, Í.
  • González Gasca, C.
  • Gómez Rodríguez, C.
  • García Quiñonez, L. V.
  • López Liévano, A.
  • Fernández Valdés, Adolfo
  • Verdeja González, Luis Felipe|||0000-0002-2392-2089
Ministerio de Ciencia e Innovación, Agencia Estatal de Investigación [FJC2019-041139-I]; Programa "Severo Ochoa" of Grants for Research and Teaching of the Principality of Asturias [BP20 041]; SFERA-III project [823802]