Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

MgO/KH2PO4 and Curing Moisture Content in MKPC Matrices to Optimize the Immobilization of Pure Al and Al-Mg Alloys

  • Fernández García, Carla
  • Alonso, María Cruz
  • Bastidas, José María
  • García-Lodeiro, Inés
  • Fernández Martín, Raúl
Magnesium Potassium Phosphate Cements (MKPCs) are considered a good alternative for the immobilization of aluminium radioactive waste. MKPC composition and moisture curing conditions are relevant issues to be evaluated. The corrosion of pure aluminium (A1050) and AlMg alloys (AA5754) with 3.5% of Mg is studied in MKPC systems prepared with different MgO/KH2PO4 (M/P) molar ratios (1, 2, and 3M) and moisture curing conditions (100% Relative Humidity (RH) and isolated in plastic containers (endogenous curing)). The Al corrosion potential (Ecorr) and corrosion kinetic (icorr and Vcorr) are evaluated over 90 days. Additionally, the pore ion evolution, the matrix electrical resistance, the pore structure, and compressive strength are analysed. The corrosion process of Al alloy is affected by the pH and ion content in the pore solution. The pore pH increases from near neutral for the 1M M/P ratio to 9 and 10 for the 2 and 3M M/P ratio, increasing in the same way the corrosion of pure Al (AA1050) and AlMg alloys (AA5754). The effect of Mg content in the alloy (AA5754) becomes more relevant with the increase in the M/P ratio. The presence of phosphate ions in the pore solution inhibits the corrosion process in both Al alloys. The MKPC physicochemical stability improved with the increase in the M/P ratio, higher mechanical strength, and more refined pore structure, This research was funded by the EURATOM research and training program 2019–2020 under grant agreement No. 945098
Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

Evaluation of fillers for Magnesium Potassium Phosphate Cement (MKPC) for the encapsulation of low and intermediate level metallic radioactive wastes

  • Dieguez, Mikel
  • Cuevas Rodríguez, Jaime Fernando
  • Alonso, María Cruz
  • García-Lodeiro, Inés
  • Fernández Martín, Raúl
  • Ruiz García, Ana Isabel
This study investigates the effect of coal fly ash (FA), wollastonite (WO), pumice (PM), and metakaolin (MK) as filler materials in the rheological, mechanical, chemical, and mineralogical properties of a magnesium potassium phosphate cement (MKPC), designed for the encapsulation of low and intermediate level radioactive wastes containing reactive metals. Workability, compression strength, dimensional stability, pH, chemical composition, and mineralogical properties were studied in different pastes and mortars of MKPC with a fixed molar ratio of MgO/KH2PO4 = 1. No new mineral phases were found with the addition of the fillers, denoting their low chemical impact on the MKPC system. Moreover, all formulations with a water/cement mass ratio of <0.65 presented compressive strengths higher than 30 MPa after 90 days, and pH values lower than 8.5, corresponding to the passivation zone of aluminum corrosion
Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

The Influence of the Magnesium-to-Phosphate Molar Ratio on Magnesium Potassium Phosphate Cement Properties Using Either Wollastonite or Volcanic Ash as Fillers

  • Padilla Encinas, María del Pilar
  • Dieguez, Mikel
  • Cuevas Rodríguez, Jaime Fernando
  • Fernández Martín, Raúl
  • Ruiz García, Ana Isabel
The use of the fillers wollastonite and volcanic ash for the formulation of magnesium phosphate cements prepared at magnesium-to-phosphate molar ratios of 2, 3 and 4 has been investigated, with the objective of evaluating these formulations for the encapsulation of aluminium radioactive waste. The workability, mechanical strength, dimensional stability, pH, chemical composition and mineralogical properties of cement pastes and mortars were examined. All cement pastes presented fast setting, and the workability was only good at 3 and 4 M. The cement mortars presented high compressive strength and dimensional stability. K-struvite was confirmed as the sole reaction product of the reaction for all formulations. The pH of the cement pastes, measured in suspensions, achieved values in the range of 7.8 to 9.5 after the first days of setting, exceeding pH 8.5 for the 2 and 3 M formulations. pH values below 8.5 are theoretically preferred to avoid potential aluminium corrosion. Both fillers presented adequate characteristics (good workability, chemical compatibility) to be used in the formulation of magnesium phosphate cements. The increasing magnesium-to-phosphate molar ratio prevented unwanted efflorescence and increased the mechanical stability of the cement, This research was funded by the European Union’s Horizon 2020 Research and Training programme 2019–2020 under grant agreement No. 945098 PREDIS: PRE-DISposal management of radioactive waste
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Digitalisation for nuclear waste management: predisposal and disposal

  • Kolditz, Olaf
  • Jacques, Diederik
  • Claret, Francis
  • Bertrand, Johan
  • Churakov, Sergey V.
  • Debayle, Christophe
  • Diaconu, Daniela
  • Fuzik, Kateryna
  • García-Cobos, D.
  • Graebling, Nico
  • Grambow, Bernd
  • Holt, Erika
  • Idiart, Andrés
  • Leira, Petter
  • Montoya, Vanessa
  • Niederleithinger, Ernst
  • Olin, Markus
  • Pfingsten, Wilfried
  • Prasianakis, Nikolaos
  • Rink, Karsten
  • Samper, Javier
  • Szöke, István
  • Szöke, Réka
  • Theodon, Louise
  • Wendling, Jacques
[Abstract:] Data science (digitalisation and artificial intelligence) became more than an important facilitator for many domains in fundamental and applied sciences as well as industry and is disrupting the way of research already to a large extent. Originally, data sciences were viewed to be well-suited, especially, for data-intensive applications such as image processing, pattern recognition, etc. In the recent past, particularly, data-driven and physics-inspired machine learning methods have been developed to an extent that they accelerate numerical simulations and became directly usable for applications related to the nuclear waste management cycle. In addition to process-based approaches for creating surrogate models, other disciplines such as virtual reality methods and high-performance computing are leveraging the potential of data sciences more and more. The present challenge is utilising the best models, input data and monitoring information to integrate multi-chemical-physical, coupled processes, multi-scale and probabilistic simulations in Digital Twins (DTw) able to mirror or predict the performance of its corresponding physical twins. Therefore, the main target of the Topical Collection is exploring how the development of DTw can benefit the development of safe, efficient solutions for the pre-disposal and disposal of radioactive waste. A particular challenge for DTw in radioactive waste management is the combination of concepts from geological modelling and underground construction which will be addressed by linking structural and multi-physics/chemistry process models to building or tunnel information models. As for technical systems, engineered structures a variety of DTw approaches already exist, the development of DTw concepts for geological systems poses a particular challenge when taking the complexities (structures and processes) and uncertainties at extremely varying time and spatial scales of subsurface environments into account., This work has been financed within the framework of EURAD, the European Joint Programme on Radioactive Waste Management (Grant Agreement No 847593) and PREDIS (Pre-disposal management of radioactive waste, Euratom research and training programme, grant agreement No 945098). The contribution of Javier Samper (UDC) was partly funded by Project PID2019-109544RB-I00). These supports are gratefully acknowledged., Open Access funding enabled and organized by Projekt DEAL.
RUC. Repositorio da Universidade da Coruña
Publicación Contribución de congreso (ConferenceOutput)

Digitalization and Digital Twins in Long Term Management of Radioactive Waste

  • Jacques, Diederik
  • Kolditz, Olaf
  • Szöke, István
  • Churakov, Sergey V.
  • García-Cobos, D.
  • Laloy, Eric
  • Montoya, Vanessa
  • Prasianakis, Nikolaos
  • Samper, Javier
[Abstract:] Digitalization and Artificial Intelligence is the fastest emerging paradigms in engineering and natural science applications. As an example data-driven and physics-inspired machine learning methods have been developed and evaluated to accelerate numerical simulations; evaluating their usability for applications related to the radioactive waste management cycle is therefore of high relevance. Under the umbrella of the European Joint Programme on Radioactive Waste Management (EURAD) and on Pre-disposal Management of Radioactive Waste (PREDIS), different initiatives have been established to facilitate evaluation and implementation of digitalization technologies (and specifically digital twins mirroring their corresponding physical assets) for long-term radioactive waste management. Previous studies indicate that digitalization is an important tool, to improve processes throughout the whole waste management cycle including pre-disposal activities like waste treatment, conditioning, storage and aspects related to the operation and long-term performance of disposal systems. However, before implementation, several challenges related to different facets of digital twins and digitalization need further research. At this stage, the specific potential and role of different aspects of digital transformation for different topics of waste management is still somewhat vague. In this contribution, an overview will be given addressing selected research developments s based on activities that are ongoing in EURAD and PREDIS or in closely related activities., This project has received funding from the Euratom research and training programme 2019-2020 under grant agreement No 945098. Results reported in section 3 are funded in the framework of EURAD (Grant Agreement No 847593). The Authors sincerely thank Tom-Robert Bryntesen, Hans-Olav Randem, Svein-Tore Edvardsen and Réka Szőke for their contribution to the developments in the PREDIS project discussed under section 4.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Position paper on high fidelity simulations for coupled processes, multi-physics and chemistry in geological disposal of nuclear waste

  • Churakov, Sergey V.
  • Claret, Francis
  • Idiart, Andrés
  • Jacques, Diederik
  • Govaerts, Joan
  • Kolditz, Olaf
  • Prasianakis, Nikolaos
  • Samper, Javier
[Abstract:] This opinion paper describes the major coupled T(Thermal)-H(Hydro)-M(Mechanical)-C(Chemical) processes in geological repository systems and the frontier of related model development. Particular focus is made on the analysis of existing approaches and open research questions with respect to the further development of coupled codes and models for realistic multi-scale simulations of repository systems. These include the use of machine learning and artificial intelligence in acceleration of computer codes; sensitivity analysis, inverse modelling and optimisation; software engineering and collaborative platforms for model development., This work has been financed within the framework of EURAD, the European Joint Programme on Radioactive Waste Management (Grant Agreement No 847593) and PREDIS (Pre-disposal management of radioactive waste, Euratom research and training programme, grant agreement No 945098). Funding was also provided by ENRESA, the Spanish Ministry of Science and Innovation (TED2021-130315B-I00, NextGenerationEU) PID2023-153202OB-I00), the Galician Regional Government (Grant ED431C2021/54), and Nagra, the National Cooperative for the Disposal of Radioactive Waste. Authors especially acknowledge the developments conducted in EURAD WPs ACED, DONUT, FUTURE & MAGIC. We appreciate the comments, suggestions and corrections of the two anonymous reviewers, which contributed to improve the manuscript., Xunta de Galicia; ED431C2021/54
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Evaluation of Fillers for Magnesium Potassium Phosphate Cement (MKPC) for the Encapsulation of Low and Intermediate Level Metallic Radioactive Wastes

  • Diéguez, Mikel
  • Ruiz, Ana Isabel
  • Cuevas, Jaime
  • Alonso, M. Cruz
  • García-Lodeiro, Inés
  • Fernández, Raúl
This study investigates the effect of coal fly ash (FA), wollastonite (WO), pumice (PM), and metakaolin (MK) as filler materials in the rheological, mechanical, chemical, and mineralogical properties of a magnesium potassium phosphate cement (MKPC), designed for the encapsulation of low and intermediate level radioactive wastes containing reactive metals. Workability, compression strength, dimensional stability, pH, chemical composition, and mineralogical properties were studied in different pastes and mortars of MKPC with a fixed molar ratio of MgO/KH<sub>2</sub>PO<sub>4</sub> = 1. No new mineral phases were found with the addition of the fillers, denoting their low chemical impact on the MKPC system. Moreover, all formulations with a water/cement mass ratio of <0.65 presented compressive strengths higher than 30 MPa after 90 days, and pH values lower than 8.5, corresponding to the passivation zone of aluminum corrosion., This research was funded from the Euratom research and training programme 2019–2020 under grant agreement No 945098., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Corrosion behavior and immobilization of pure aluminum and Al-Mg alloy LLRW in magnesium potassium phosphate cements

  • Perona, R.
  • Fernández-García, Carla
  • García-Lodeiro, Inés
  • Criado Sanz, María
  • Bastidas Rull, José María
  • Alonso, M. Cruz
Magnesium potassium phosphate cement (MKPC) is a candidate material to replace ordinary Portland cement (OPC) for the encapsulation of metallic low-level radioactive waste (LLRW) and improve the corrosion behavior of encapsulated reactive metals such as aluminum. The objectives of this research were to study the corrosion behavior of pure Al (A1050) and Al¿Mg alloy (AA5754) embedded in MKPC and OPC mortars, to assess the effect of curing conditions on hardening properties and on the reactivity of Al and Al¿Mg alloy. Results were obtained with measurements of compressive strength, X-ray diffraction and polarization resistance and the proposed interpretation was based on Faraday¿s law. In the first 15 days of interaction in water immersion the corrosion rate and the volume of hydrogen evolved were seen to be at least one order of magnitude lower for AA5754 in MKPC than in OPC mortar, yielding average corrosion current density values of 1.85 and 109.0 × 10¿6 A/cm2, and hydrogen volumes of 0.33 L/m2 and 17.8 L/m2 for AA5754/MKPC and AA5754/OPC, respectively. The pore pH was close to neutral and the hardening properties were highly dependent on the curing conditions., This Project has received funding from the European Union's Horizon 2020 Research and Innovation Program for Nuclear Fission and Radiation Protection Research (call NFRP−2019−2020) under grant agreement No. 945098 (PREDIS). Also acknowledgements of C.F.G. for the project funded by the CSIC, PIE (202260E009), I.G.L. for the JIN project (PID2020−116738RJ−100) funded by the Ministry of Science and Innovation of Spain, and M.C. for the project funded by the Community of Madrid (2019−T1/AMB−13672)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

MgO/KH2PO4 and Curing Moisture Content in MKPC Matrices to Optimize the Immobilization of Pure Al and Al-Mg Alloys

  • Fernández-García, Carla
  • Alonso, M. Cruz
  • Bastidas Rull, José María
  • García-Lodeiro, Inés
  • Fernández, Raúl
© 2024 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/)., Magnesium Potassium Phosphate Cements (MKPCs) are considered a good alternative for the immobilization of aluminium radioactive waste. MKPC composition and moisture curing conditions are relevant issues to be evaluated. The corrosion of pure aluminium (A1050) and AlMg alloys (AA5754) with 3.5% of Mg is studied in MKPC systems prepared with different MgO/KH2PO4 (M/P) molar ratios (1, 2, and 3M) and moisture curing conditions (100% Relative Humidity (RH) and isolated in plastic containers (endogenous curing)). The Al corrosion potential (Ecorr) and corrosion kinetic (icorr and Vcorr) are evaluated over 90 days. Additionally, the pore ion evolution, the matrix electrical resistance, the pore structure, and compressive strength are analysed. The corrosion process of Al alloy is affected by the pH and ion content in the pore solution. The pore pH increases from near neutral for the 1M M/P ratio to 9 and 10 for the 2 and 3M M/P ratio, increasing in the same way the corrosion of pure Al (AA1050) and AlMg alloys (AA5754). The effect of Mg content in the alloy (AA5754) becomes more relevant with the increase in the M/P ratio. The presence of phosphate ions in the pore solution inhibits the corrosion process in both Al alloys. The MKPC physicochemical stability improved with the increase in the M/P ratio, higher mechanical strength, and more refined pore structure., This research was funded by the EURATOM research and training program 2019–2020 under grant agreement No. 945098., The authors acknowledge the following projects: European Union’s Horizon 2020 Research and Innovation Program for Nuclear Fission and Radiation Protection Research (call NFRP-2019-2020) under grant agreement No. 945098 (PREDIS); M.C.A. and C.F.-G. acknowledge the CSIC PIE (No. 202260E009); and I.G.-L. acknowledges the Nat project AEI (PID PID2020-116738RJ-I00/AEI/10.13039/501100011033)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Passivation of aluminium A1050 in MKPC matrices: effect of MgO type and chemical retarder composition

  • Fernández-García, Carla
  • Le, Kim Khanh
  • Alonso, M. Cruz
  • Cannes, Céline
  • Delpech, Sylvie
Magnesium potassium phosphate cement (MKPC) is a promising material for encapsulating low- to intermediate-level radioactive metallic wastes, including aluminium. This study investigates the influence of magnesium oxide (MgO) type and chemical retarders—boric acid and sodium thiosulfate—on the passivation of aluminium A1050 alloy. Corrosion behaviour and hydrogen evolution were monitored over 25 days in aqueous solutions and 230 days in mortars using electrochemical impedance spectroscopy and linear polarisation resistance. In aqueous solutions, boric acid improved passivation by shifting the corrosion potential to more anodic values, while thiosulfate promoted rapid passivation through adsorption, leading to slightly lower anodic potentials. In mortars, the near-neutral pH facilitated passivation, though variations were observed depending on the MgO type and retarder composition. Soft-burnt MgO combined with thiosulfate accelerated the formation of the alumina layer, enhancing passivation and reducing corrosion kinetics due to its higher reactivity and refined pore structure. In contrast, hard-burnt MgO with boric acid resulted in slower passivation and more cathodic potentials, likely due to its lower reactivity and heterogeneous pore network. When both retarders were used together, a competitive effect was observed, reducing passivation efficiency and increasing hydrogen evolution despite anodic potential shifts. These findings underscore the critical role of MgO type and retarder selection in optimising aluminium passivation within MKPC systems., The authors acknowledge the funding from the European Union's Horizon 2020 Research and Innovation Program for Nuclear Fission and Radiation Protection Research (call NFRP-2019-2020) under grant agreement No. 945098 (PREDIS). Carla Fernández-García and María Cruz Alonso also acknowledge the support from the CSIC PIE (No. 202260E009)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Aluminium corrosion reactivation in MKPC and Portland-based wasteforms under simulated alkaline repository conditions

  • Fernández-García, Carla
  • Alonso, M. Cruz
The long-term stability of aluminium (Al) in cementitious wasteforms is challenged by matrix alkalinisation resulting from interaction with alkaline waters from engineered barriers in low- to intermediate-level radioactive waste (LILRW) repositories. This study evaluates the corrosion of Al (A1050) and Al-Mg (AA5754) alloys and the physicochemical evolution of magnesium potassium phosphate cement (MKPC) and Portland-based matrices (CEM I and CEM I + 50% silica fume (SF)) under simulated alkaline exposure. Over 250 days, specimens were subjected to synthetic alkaline water (SPAW), while MKPC was also embedded in a CEM I mortar (AM) to simulate repository contact conditions. In MKPC, alkaline plume diffusion from the external source triggered ion exchange with the matrix, leading to alkalinisation (pH >11), reactivation of Al corrosion, and H₂ release to levels comparable to those observed in CEM I. K-struvite dissolution, Ca–P-rich phase formation, and fly ash hydration were also observed, evidencing long-term destabilisation of the MKPC matrix. In contrast, CEM I + 50%SF, despite being exposed to a highly alkaline plume, maintained the pore solution pH at 10.7 over time due to the advanced hydration of SF, effectively limiting Al reactivity and H₂ generation without matrix alteration., The authors acknowledge funding from the European Union's Horizon 2020 Research and Innovation Programme for Nuclear Fission and Radiation Protection Research (NFRP-2019–2020 call) under Grant Agreement No. 945098 (PREDIS), as well as support from the CSIC PIE (Project No. 202260E009) and EURAD 2 (Project No. 10116671)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Comparative Assessment of Cement and Geopolymer Immobilization Approaches: Short-Term Leaching Performance of Thermally Treated Ion Exchange Resin Waste Forms

  • Fernández, Raúl
  • Perez-Cortes, Pedro
  • Marugán, Esther Irene
  • Puertas, Francisca
  • García-Lodeiro, Inés
  • Ruiz, Ana Isabel
  • Cuevas, Jaime Fernando
  • Turrero, María Jesús
  • Torres, Elena
  • Alonso, M. Cruz
  • Padilla Encinas, Pilar
This article belongs to the Special Issue Radioactive Waste Treatment and Environment Recovery., Cementation using Ordinary Portland Cement (OPC) remains the standard method for conditioning low- and intermediate-level radioactive waste, including Spent Ion Exchange Resins (SIERs). This work presents an integrated strategy involving thermal pretreatment to minimize waste volume and eliminate organic constituents, followed by encapsulation within three distinct binders: CEM I, CEM III, and a novel one-part geopolymer. The one-part geopolymer system represents a significant operational innovation, enabling safe and simple “just-add-water” processing and avoiding the need to handle alkaline solutions. The proposed geopolymer, synthesized from metakaolin, blast furnace slag, and solid sodium silicate, was systematically benchmarked against conventional OPC matrices (CEM I, CEM III) by assessing their capacity to immobilize thermally treated SIER ashes under accelerated leaching conditions. For benchmarking, leaching indices for Cs and Sr were determined following the ANSI/ANS 16.9 standard protocol in three representative environments simulating operational and long-term repository scenarios, providing a quantitative evaluation of radionuclide retention and matrix durability. Results indicate that the one-part geopolymer improved leaching indices for Cs and Sr compared to both cementitious binders and complied with regulatory waste acceptance criteria. The comparative results highlight the potential of geopolymer technology to increase waste loading efficiencies and improve long-term safety, establishing a robust framework for future radioactive waste management approaches., This work was supported by funding from the European Union’s Horizon 2020 Research and Training programme 2019–2020 under grant agreement No. 945098 PREDIS: PRE-DISposal management of radioactive waste., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mechanistic role of phosphate and borate species in aluminium passivation in simulated MKPC pore solutions

  • Fernández-García, Carla
  • Alonso, M. Cruz
Aluminium corrosion is a key constraint in the formulation of magnesium potassium phosphate cements (MKPC) for the effective immobilisation of this reactive metal in low- and intermediate-level radioactive waste repositories. This study examines the role of phosphate and borate species in controlling passivation through electrochemical analyses in solutions representative of MKPC pore chemistries, benchmarked against OPC-like media. Electrochemical impedance spectroscopy, linear polarisation resistance, and estimated hydrogen release were used to characterise interfacial processes across ion concentrations and exposure periods. Results reveal distinct roles of phosphate and borate in aluminium passivation. Phosphate (H₂PO₄⁻, pH 4–5) at high concentrations (≥3000 ppm) drives rapid passivation via multilayer film formation, while borate (B(OH)₄⁻/H₂BO₃⁻, pH ≈8.5) becomes increasingly influential at lower levels (200–300 ppm), stabilising compact oxide films by adsorption. Mixed phosphate–borate systems reproduced the chemistry of hydrated MKPC solutions, highlighting their complementary action in establishing and maintaining passivity. Compared to OPC conditions (Ca(OH)₂, pH 12.7), which sustain active corrosion, MKPC chemistries favour stable aluminium passivation and suppress hydrogen evolution. The findings provide mechanistic insight into the inhibition processes underlying MKPC corrosion resistance and its suitability for immobilising radioactive aluminium., The authors acknowledge the funding from the European Union\u2019s Horizon 2020 Research and Innovation Program for Nuclear Fission and Radiation Protection Research (call NFRP-2019-2020 ) under grant agreement No 945098 (PREDIS) . The authors also acknowledge the support from the CSIC PIE projects No 202260E009 and No 202560E173 ., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnesium Potassium Phosphate Cement for Low- and Intermediate-level Radioactive Waste Conditioning: Advances Limitations and Future Trends

  • Fernández-García, Carla
  • Padilla Encinas, Pilar
  • Fernández, Raúl
  • Criado Sanz, María
  • García-Lodeiro, Inés
  • Torres, Elena
  • Alonso, M. Cruz
In Press, Journal Pre-proof, Low- and intermediate-level radioactive waste (LILRW) comprises a highly heterogeneous range of materials that require immobilisation matrices capable of ensuring mechanical stability, chemical compatibility, and limited radionuclide mobility over extended time scales. Conventional cementitious binders, such as Portland cement (PC) and alkali-activated systems, are widely used for waste conditioning but may present limitations when applied to waste streams incompatible with highly alkaline environments, including certain reactive metals and ion-exchange resins. Magnesium potassium phosphate cement (MKPC) has emerged as a promising alternative binder due to its near-neutral pore solution pH, low water demand, rapid setting behaviour, and the formation of stable crystalline phases such as K-struvite. This review synthesises current knowledge on MKPC as a conditioning matrix for LILRW, with particular attention to the formulation parameters that control its reaction kinetics, phase assemblage, and the microstructural development. Key aspects examined include MgO reactivity, MgO/KH2PO4 molar ratio, water content, chemical retarders, mineral additions, and curing conditions. The implications of these parameters for key material properties relevant to waste immobilisation, such as mechanical strengths, pore solution chemistry, porosity, durability under leaching, corrosion and irradiation, are critically assessed. Overall, the available evidence highlights the potential of MKPC as a promising binder for challenging LILRW streams, while also identifying key knowledge gaps related to long-term performance under repository-relevant conditions, radionuclide retention mechanisms, broader radionuclide coverage, and formulation optimisation before large-scale implementation can be fully realised., The authors acknowledge funding from the European Union’s Horizon 2020 Research and Innovation Programme for Nuclear Fission and Radiation Protection Research (NFRP-2019-2020 call) under Grant Agreements No. 945098 (PREDIS) and 10116671 (EURAD-2). C. Fernández-García and M. C. Alonso also acknowledge support from the CSIC PIE projects No. 202260E009 and No. 202560E173., Peer reviewed