Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

IRTA Pubpro. Open Digital Archive
Publicación Artículo científico (JournalArticle)

Pesticide dose adjustment in fruit and grapevine orchards by DOSA3D: Fundamentals of the system and on-farm validation

  • Román, Carla
  • Peris, Miquel
  • Esteve, Joan
  • Tejerina, Miguel
  • Cambray, Jordi
  • Vilardell, Pere
  • Planas, Santiago
Agricultural productivity cannot be sustained without the application of plant protection measures. Within the framework of integrated pest management (IPM), the use of chemical pesticides should be limited to the last option among the available practices. Even though their use remains common, it carries associated environmental and human health risks. One of the most accepted practices within IPM is the reduction of spraying events and/or pesticide applied doses. DOSA3D is a decision support system that allows the dose to be adjusted to the specific treatment scenario. For this, DOSA3D calculates the optimal application volume rate by estimating the leaf area index and takes into account the overall spraying efficiency and the pest or disease to be controlled. The system adopts specific minimum volume rates for fruit trees and vineyards without compromising the crop health status. To establish the adjusted dose, the labeled or the adviser prescription concentration is kept. Resulting adjusted doses provided by DOSA3D achieved pesticide savings up to 53% in fruit trees and 60% in vineyards. DOSA3D has been validated against the main diseases and pests of fruit trees and vineyards: brown spot and psylla in pear orchards; alternaria blotch disease, apple scab, codling moth, oriental moth and red spider mite in apple orchards; powdery mildew, brown rot, aphids, thrips and mites in peach orchards; and, powdery mildew, yellow spider mite and leafhoppers in grapevine orchards. In addition, a methodology called Green Way is presented to provide consistent and crop safety pesticide doses when these are labeled as concentration or ground area doses., info:eu-repo/semantics/publishedVersion
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

A review of methods and applications of the geometric characterization of tree crops in agricultural activities

  • Rosell Polo, Joan Ramon
  • Sanz Cortiella, Ricardo
This paper presents the foundations and applications in agriculture of the main systems used for the geometrical characterization of tree plantations, including systems based on ultrasound, digital photographic techniques, light sensors, high-resolution radar images, high-resolution X-ray computed tomography, stereo vision and LIDAR sensors. Amongst these, LIDAR laser scanners and stereo vision systems are probably the most promising and complementary techniques for achieving 3D pictures and maps of plants and canopies. The information about the geometric properties of plants provided by these techniques has innumerable applications in agriculture. Some important agricultural tasks that can benefit from these plant-geometry characterization techniques are the application of pesticides, irrigation, fertilization and crop training. In the field of pesticide application, knowledge of the geometrical characteristics of plantations will permit a better adjustment of the dose of the product applied, improving the environmental and economic impact. However, it is still necessary to resolve several technological and commercial questions. The former include improving detection systems, especially with regard to developing software for the post-processing steps and improving the speed of calculation and decision making. Amongst the latter, it is essential to produce low cost sensors and control systems in order to facilitate large-scale deployment. Obtaining a precise geometrical characterization of a crop at any point during its production cycle by means of a new generation of affordable and easy-to-use detection systems, such as LIDAR and stereo vision systems, will help to establish precise estimations of crop water needs as well as valuable information that can be used to quantify its nutritional requirements. If accurate, this can provide valuable information on which to base more sustainable irrigation and fertilizer dosages. These would be able to meet crop needs and could also be used as part of specific management systems, based on prescription maps, for the application of variable quantities of water and fertilizers. The availability of measurement tools that allow a precise geometric characterization of plantations will also facilitate and enhance research aimed at developing better crop training systems that ensure an optimal distribution of light within the treetops and higher fruit quality. It is therefore of vital importance to continue devoting major efforts to the development of increasingly accurate, robust and affordable systems capable of measuring the geometric characteristics of plantations, which support the development of the different areas of a sustainable and precision agriculture., This work has been funded by the Spanish Ministry of Science and Innovation and by the European Union through the FEDER funds and is part of research projects Pulvexact (AGL2002-04260-C04-02) and Optidosa (AGL2007-66093-C04-03).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

A tractor-mounted scanning LIDAR for the non-destructive measurement of vegetative volume and surface area of tree-row plantations: a comparison with conventional destructive measurements

  • Rosell Polo, Joan Ramon
  • Sanz Cortiella, Ricardo
  • Llorens Calveras, Jordi
  • Arnó Satorra, Jaume
  • Escolà i Agustí, Alexandre
  • Ribes Dasi, Manuel
  • Masip Vilalta, Joan
  • Camp, Ferran
  • Gràcia, Felip
  • Solanelles Batlle, Francesc
  • Pallejà Cabrè, Tomàs
  • Val, Luis
  • Planas de Martí, Santiago
  • Gil Moya, Emilio
  • Palacín Roca, Jordi
The use of a low-cost tractor-mounted scanning Light Detection and Ranging (LIDAR) system for capable of making non-destructive recordings of tree-row structure in orchards and vineyards is described. Field tests consisted of several LIDAR measurements on both sides of the crop row, before and after defoliation of selected trees. Summary parameters describing the tree-row volume and the total crop surface area viewed by the LIDAR (expressed as a ratio with ground surface area) were derived using a suitable numerical algorithm. The results for apple and pear orchards and a wine producing vineyard were shown to be in reasonable agreement with the results derived from a destructive leaf sampling method. Also, good correlation was found between manual and sensor-based measurements of the vegetative volume of tree-row plantations. The Tree Area Index parameter, TAI, gave the best correlation between destructive and non-destructive (i.e. LIDAR-based) determinants of crop leaf area. The LIDAR system proved to be a powerful technique for low cost, prompt and non-destructive estimates of the volume and leaf-area characteristics of plants., This research was funded by the CICYT (Comisión Interministerial de Ciencia y Tecnología, Spain), under Agreement No. AGL2002-04260-C04-02.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Obtaining the three-dimensional structure of tree orchards from remote 2D terrestrial LIDAR scanning

  • Rosell Polo, Joan Ramon
  • Llorens Calveras, Jordi
  • Sanz Cortiella, Ricardo
  • Arnó Satorra, Jaume
  • Ribes Dasi, Manuel
  • Masip Vilalta, Joan
  • Escolà i Agustí, Alexandre
  • Camp, Ferran
  • Solanelles Batlle, Francesc
  • Gràcia, Felip
  • Gil Moya, Emilio
  • Val, Luis
  • Planas de Martí, Santiago
  • Palacín Roca, Jordi
In recent years, LIDAR (light detection and ranging) sensors have been widely used to measure environmental parameters such as the structural characteristics of trees, crops and forests. Knowledge of the structural characteristics of plants has a high scientific value due to their influence in many biophysical processes including, photosynthesis, growth, CO2-sequestration and evapotranspiration, playing a key role in the exchange of matter and energy between plants and the atmosphere, and affecting terrestrial, above-ground, carbon storage. In this work, we report the use of a 2D LIDAR scanner in agriculture to obtain three-dimensional (3D) structural characteristics of plants. LIDAR allows fast, non-destructive measurement of the 3D structure of vegetation (geometry, size, height, cross-section, etc.). LIDAR provides a 3D cloud of points, which is easily visualized with Computer Aided Design software. Three-dimensional, high density data are uniquely valuable for the qualitative and quantitative study of the geometric parameters of plants. Results are demonstrated in fruit and citrus orchards and vineyards, leading to the conclusion that the LIDAR system is able to measure the geometric characteristics of plants with sufficient precision for most agriculture applications. The developed system made it possible to obtain 3D digitalized images of crops, from which a large amount of plant information – such as height, width, volume, leaf area index and leaf area density – could be obtained. There was a great degree of concordance between the physical dimensions, shape and global appearance of the 3D digital plant structure and the real plants, revealing the coherence of the 3D tree model obtained from the developed system with respect to the real structure. For some selected trees, the correlation coefficient obtained between manually measured volumes and those obtained from the 3D LIDAR models was as high as 0.976., This research was funded by the CICYT (Comisión Interministerial de Ciencia y Tecnología, Spain), under Agreement No. AGL2002-04260-C04-02. LMS200 and SICK are trademarks of SICK AG, Germany.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

LIDAR and non-LIDAR-based canopy parameters to estimate the leaf area in fruit trees and vineyard

  • Sanz Cortiella, Ricardo
  • Llorens Calveras, Jordi
  • Escolà i Agustí, Alexandre
  • Arnó Satorra, Jaume
  • Planas de Martí, Santiago
  • Román, Carla
  • Rosell Polo, Joan Ramon
This paper is based on two initial hypotheses, firstly, it is proposed that the vegetation volume obtained with a LIDAR-based system or tree row LIDAR volume (TRLV) has a high correlation with the leaf area (LA). Secondly, it is proposed that the projected outer surface or projected tree row surface (PTRS), also LIDAR-based, is linearly related with the LA. The verification of these two hypotheses corresponds to the first two objectives of this work. The third objective is to propose an alternative method, without using LIDAR sensors, simpler and more economical, for in situ LA evaluation. To achieve these objectives a total of 17 blocks of pear, 14 of apple and 26 of vine, in different phenological states, were LIDAR scanned and subsequently manually defoliated. After the field and calculation work, the TRLV and LA were compared. The logarithmic regressions obtained had high correlations. For apple and pear trees the equations are practically the same with R2 of 0.85 and 0.84, respectively. The equation corresponding to vines is somewhat different and has an R2 of 0.86. The regression without species differentiation is 3.66ln(x) +9.65 with R2=0.90. Based on the TRLV, the front and top projected surface areas of each block were then obtained and, using these variables, the PTRS. The linear regressions obtained between PTRS and LA have high correlations with R2 of 0.88, 0.85 and 0.80 for apple trees, pear trees, and vineyard respectively. The three crops show very similar behavior. The straight lines are very close, with very similar slopes. With no species differentiation the linear regression model is y=1.47x - 1.18 with R2=0.93. The starting point of the third objective is to obtain the projected surfaces, frontal and top, without using a LIDAR sensor. These surfaces are not as precise as those obtained with LIDAR and for this reason they are referred to as 'estimated' projected surfaces. To calculate the estimated PTRS without a LIDAR sensor, the height and depth of the vegetation are measured with a tape measure. It is also necessary to make a visual estimation of the frontal gap-fraction. For this, a training method with known gap-fraction pictograms is proposed. The final results with this non-LIDAR method are very similar to those obtained with LIDAR. This method, although it needs human intervention, is simple, easy, economical and precise for in situ LA estimation., This research was partially funded by the Spanish Ministry of Economy and Competitiveness (projects AGL2002-04260-C04-02, AGL2007-66093-C04-03, AGL2010-22304-C04-03 and AGL2013- 48297-C2-2-R) and EU FEDER. Funding of Secretaria d’Universitats i Recerca del Departament d’Empresa i Coneixement de la Generalitat de Catalunya under Grant 2017 SGR 646 is also thanked.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Relationship between tree row LIDAR-volume and leaf area density for fruit orchards and vineyards obtained with a LIDAR 3D Dynamic Measurement System

  • Sanz Cortiella, Ricardo
  • Rosell Polo, Joan Ramon
  • Llorens Calveras, Jordi
  • Gil Moya, Emilio
  • Planas de Martí, Santiago
In this work, a LIDAR 3D Dynamic Measurement System, based on a Two-Dimensional Terrestrial Laser-LIDAR Scanner (2D TLS), was used for the geometric characterisation of tree-row crops (apple trees, pear trees and vineyards). The trees were scanned with the LIDAR system from opposite sides to obtain two three-dimensional point clouds. The point clouds were registered and the volume occupied by the resulting point cloud, tree row LIDAR-volume (TRLV), was graphically and numerically obtained. The study undertaken in this paper is based on the hypothesis that there may exist a non-linear relationship between the TRLV and the leaf area density (LAD). The main objective is to examine the relationship between TRLV and LAD in vineyards, apple and pear orchards. The study of 35 blocks of vegetation reveals a good logarithmic fit, y = −0.36 ln(x) + 3.69 with R2 = 0.87, between the TRLV (x) in dm3 and the LAD (y) in dm−1. It would appear that the TRLV of the crops under study (planted in a hedgerow-type configuration) is in itself an explanation of the LAD. The competition for light between the leaves and the space that these leaves occupy appear to follow a similar model in the three crops. According to the results of this study, the LAD can be estimated from the TRLV. If the LAD is multiplied by the TRLV, the leaf area of the vegetation under study can be obtained. It is therefore concluded that by using the information provided by the LIDAR 3D Dynamic Measurement System, a good estimation can be obtained of the leaf area in hedgerow fruit tree crops and hedgerow vineyards., This work has been funded by the Spanish Ministry of Science and Innovation and by the European Union through the FEDER funds and is part of research projects Pulvexact (AGL2002-04260-C04-02), Optidosa (AGL2007-66093-C04-03) and Safespray (AGL2010-22304-C04-03).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Characterisation of the LMS200 laser beam under the influence of blockage surfaces. Influence on 3D scanning of tree orchards

  • Sanz Cortiella, Ricardo
  • Llorens Calveras, Jordi
  • Rosell Polo, Joan Ramon
  • Gregorio López, Eduard
  • Palacín Roca, Jordi
The geometric characterisation of tree orchards is a high-precision activity comprising the accurate measurement and knowledge of the geometry and structure of the trees. Different types of sensors can be used to perform this characterisation. In this work a terrestrial LIDAR sensor (SICK LMS200) whose emission source was a 905-nm pulsed laser diode was used. Given the known dimensions of the laser beam cross-section (with diameters ranging from 12 mm at the point of emission to 47.2 mm at a distance of 8 m), and the known dimensions of the elements that make up the crops under study (flowers, leaves, fruits, branches, trunks), it was anticipated that, for much of the time, the laser beam would only partially hit a foreground target/object, with the consequent problem of mixed pixels or edge effects. Understanding what happens in such situations was the principal objective of this work. With this in mind, a series of tests were set up to determine the geometry of the emitted beam and to determine the response of the sensor to different beam blockage scenarios. The main conclusions that were drawn from the results obtained were: (i) in a partial beam blockage scenario, the distance value given by the sensor depends more on the blocked radiant power than on the blocked surface area; (ii) there is an area that influences the measurements obtained that is dependent on the percentage of blockage and which ranges from 1.5 to 2.5 m with respect to the foreground target/object. If the laser beam impacts on a second target/object located within this range, this will affect the measurement given by the sensor. To interpret the information obtained from the point clouds provided by the LIDAR sensors, such as the volume occupied and the enclosing area, it is necessary to know the resolution and the process for obtaining this mesh of points and also to be aware of the problem associated with mixed pixels., This research was funded by FEDER (Fondo Europeo de Desarrollo Regional) and the CICYT (Comisión Interministerial de Ciencia y Tecnología, Spain), under Agreement N, AGL2002-04260-C04-02 and AGL2010-22304-C04-03. LMS200 and SICK are trademarks of SICK AG, Germany.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Pesticide dose adjustment in fruit and grapevine orchards by DOSA3D: Fundamentals of the system and on-farm validation

  • Román, Carla
  • Peris Giner, Miquel
  • Esteve, Joan
  • Tejerina, Miguel
  • Cambray, Jordi
  • Vilardell i Coderch, Pere
  • Planas de Martí, Santiago
Agricultural productivity cannot be sustained without the application of plant protection measures. Within the framework of integrated pest management (IPM), the use of chemical pesticides should be limited to the last option among the available practices. Even though their use remains common, it carries associated environmental and human health risks. One of the most accepted practices within IPM is the reduction of spraying events and/or pesticide applied doses. DOSA3D is a decision support system that allows the dose to be adjusted to the specific treatment scenario. For this, DOSA3D calculates the optimal application volume rate by estimating the leaf area index and takes into account the overall spraying efficiency and the pest or disease to be controlled. The system adopts specific minimum volume rates for fruit trees and vineyards without compromising the crop health status. To establish the adjusted dose, the labeled or the adviser prescription concentration is kept. Resulting adjusted doses provided by DOSA3D achieved pesticide savings up to 53% in fruit trees and 60% in vineyards. DOSA3D has been validated against the main diseases and pests of fruit trees and vineyards: brown spot and psylla in pear orchards; alternaria blotch disease, apple scab, codling moth, oriental moth and red spider mite in apple orchards; powdery mildew, brown rot, aphids, thrips and mites in peach orchards; and, powdery mildew, yellow spider mite and leafhoppers in grapevine orchards. In addition, a methodology called Green Way is presented to provide consistent and crop safety pesticide doses when these are labeled as concentration or ground area doses., his study wasfinanced by the EU Horizon 2020 project EUCLID[grant number 633999], the Spanish Ministry of Economy and Compet-itiveness project AgVance [AGL2013-48297-C2-2-R] and the SpanishMinistry of Agriculture, Fisheries and Food project GOPHYTOVID [con-tract 2018002001192]. We are also grateful for funding by theSecretaria d'Universitats i Recerca del Departament d'Empresa iConeixement de la Generalitat de Catalunya under Grant 2017 SGR 646
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Leaf area index estimation in vineyards using a ground-based LiDAR scanner

  • Arnó Satorra, Jaume
  • Escolà i Agustí, Alexandre
  • Vallès Petit, Josep Maria
  • Llorens Calveras, Jordi
  • Sanz Cortiella, Ricardo
  • Masip Vilalta, Joan
  • Palacín Roca, Jordi
  • Rosell Polo, Joan Ramon
Estimation of grapevine vigour using mobile proximal sensors can provide an indirect method for determining grape yield and quality. Of the various indexes related to the characteristics of grapevine foliage, the leaf area index (LAI) is probably the most widely used in viticulture. To assess the feasibility of using light detection and ranging (LiDAR) sensors for predicting the LAI, several field trials were performed using a tractor-mounted LiDAR system. This system measured the crop in a transverse direction along the rows of vines and geometric and structural parameters were computed. The parameters evaluated were the height of the vines (H), the cross-sectional area (A), the canopy volume (V) and the tree area index (TAI). This last parameter was formulated as the ratio of the crop estimated area per unit ground area, using a local Poisson distribution to approximate the laser beam transmission probability within vines. In order to compare the calculated indexes with the actual values of LAI, the scanned vines were defoliated to obtain LAI values for different row sections. Linear regression analysis showed a good correlation (R 2 = 0.81) between canopy volume and the measured values of LAI for 1 m long sections. Nevertheless, the best estimation of the LAI was given by the TAI (R 2 = 0.92) for the same length, confirming LiDAR sensors as an interesting option for foliage characterization of grapevines. However, current limitations exist related to the complexity of data process and to the need to accumulate a sufficient number of scans to adequately estimate the LAI., This research was funded by ERDF (European Regional Development Fund) and the Spanish Ministry of Science and Education (Agreement No. AGL2002-04260-C04-02, and acronym PULVEXACT, and Agreement No. AGL2007-66093-C04-03, and acronym OPTIDOSA)
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Innovative LIDAR 3D dynamic measurement system to estimate fruit-tree leaf area

  • Sanz Cortiella, Ricardo
  • Llorens Calveras, Jordi
  • Escolà i Agustí, Alexandre
  • Arnó Satorra, Jaume
  • Ribes Dasi, Manuel
  • Masip Vilalta, Joan
  • Camp, Ferran
  • Gràcia Aguilà, Felipe José
  • Solanelles Batlle, Francesc
  • Planas de Martí, Santiago
  • Pallejà Cabrè, Tomàs
  • Palacín Roca, Jordi
  • Gregorio López, Eduard
  • Del Moral Martínez, Ignacio
  • Rosell Polo, Joan Ramon
In this work, a LIDAR-based 3D Dynamic Measurement System is presented and evaluated for the geometric characterization of tree crops. Using this measurement system, trees were scanned from two opposing sides to obtain two three-dimensional point clouds. After registration of the point clouds, a simple and easily obtainable parameter is the number of impacts received by the scanned vegetation. The work in this study is based on the hypothesis of the existence of a linear relationship between the number of impacts of the LIDAR sensor laser beam on the vegetation and the tree leaf area. Tests performed under laboratory conditions using an ornamental tree and, subsequently, in a pear tree orchard demonstrate the correct operation of the measurement system presented in this paper. The results from both the laboratory and field tests confirm the initial hypothesis and the 3D Dynamic Measurement System is validated in field operation. This opens the door to new lines of research centred on the geometric characterization of tree crops in the field of agriculture and, more specifically, in precision fruit growing., This work has been funded by the Spanish Ministry of Science and Innovation and by the European Union through the FEDER funds and is part of the research projects Pulvexact (AGL2002-04260-C04-02), Optidosa (AGL2007-66093-C04-03) and Safespray (AGL2010-22304-C04-03).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Performance of an ultrasonic ranging sensor in apple tree canopies

  • Escolà i Agustí, Alexandre
  • Planas de Martí, Santiago
  • Rosell Polo, Joan Ramon
  • Pomar Gomà, Jesús
  • Camp, Ferran
  • Solanelles Batlle, Francesc
  • Gràcia, Felip
  • Llorens Calveras, Jordi
  • Gil Moya, Emilio
Electronic canopy characterization is an important issue in tree crop management. Ultrasonic and optical sensors are the most used for this purpose. The objective of this work was to assess the performance of an ultrasonic sensor under laboratory and field conditions in order to provide reliable estimations of distance measurements to apple tree canopies. To this purpose, a methodology has been designed to analyze sensor performance in relation to foliage ranging and to interferences with adjacent sensors when working simultaneously. Results show that the average error in distance measurement using the ultrasonic sensor in laboratory conditions is ±0.53 cm. However, the increase of variability in field conditions reduces the accuracy of this kind of sensors when estimating distances to canopies. The average error in such situations is ±5.11 cm. When analyzing interferences of adjacent sensors 30 cm apart, the average error is ±17.46 cm. When sensors are separated 60 cm, the average error is ±9.29 cm. The ultrasonic sensor tested has been proven to be suitable to estimate distances to the canopy in field conditions when sensors are 60 cm apart or more and could, therefore, be used in a system to estimate structural canopy parameters in precision horticulture., This work has been funded by the Spanish Ministry of Science and Innovation and by the European Union through the FEDER funds and is part of research projects Pulvexact (AGL2002-04260-C04-02), Optidosa (AGL2007-66093-C04-03) and Safespray (AGL2010-22304-C04-03).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A review of methods and applications of the geometric characterization of tree crops in agricultural activities

  • Rosell Polo, Joan Ramon
  • Sanz Cortiella, Ricardo
This paper presents the foundations and applications in agriculture of the main systems used for the geometrical characterization of tree plantations, including systems based on ultrasound, digital photographic techniques, light sensors, high-resolution radar images, high-resolution X-ray computed tomography, stereo vision and LIDAR sensors. Amongst these, LIDAR laser scanners and stereo vision systems are probably the most promising and complementary techniques for achieving 3D pictures and maps of plants and canopies. The information about the geometric properties of plants provided by these techniques has innumerable applications in agriculture. Some important agricultural tasks that can benefit from these plant-geometry characterization techniques are the application of pesticides, irrigation, fertilization and crop training. In the field of pesticide application, knowledge of the geometrical characteristics of plantations will permit a better adjustment of the dose of the product applied, improving the environmental and economic impact. However, it is still necessary to resolve several technological and commercial questions. The former include improving detection systems, especially with regard to developing software for the post-processing steps and improving the speed of calculation and decision making. Amongst the latter, it is essential to produce low cost sensors and control systems in order to facilitate large-scale deployment. Obtaining a precise geometrical characterization of a crop at any point during its production cycle by means of a new generation of affordable and easy-to-use detection systems, such as LIDAR and stereo vision systems, will help to establish precise estimations of crop water needs as well as valuable information that can be used to quantify its nutritional requirements. If accurate, this can provide valuable information on which to base more sustainable irrigation and fertilizer dosages. These would be able to meet crop needs and could also be used as part of specific management systems, based on prescription maps, for the application of variable quantities of water and fertilizers. The availability of measurement tools that allow a precise geometric characterization of plantations will also facilitate and enhance research aimed at developing better crop training systems that ensure an optimal distribution of light within the treetops and higher fruit quality. It is therefore of vital importance to continue devoting major efforts to the development of increasingly accurate, robust and affordable systems capable of measuring the geometric characteristics of plantations, which support the development of the different areas of a sustainable and precision agriculture., This work has been funded by the Spanish Ministry of Science and Innovation and by the European Union through the FEDER funds and is part of research projects Pulvexact (AGL2002-04260-C04-02) and Optidosa (AGL2007-66093-C04-03).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Leaf area index estimation in vineyards using a ground-based LiDAR scanner

  • Arnó Satorra, Jaume
  • Escolà i Agustí, Alexandre
  • Vallès Petit, Josep Maria
  • Llorens Calveras, Jordi
  • Sanz Cortiella, Ricardo
  • Masip Vilalta, Joan
  • Palacín Roca, Jordi
  • Rosell Polo, Joan Ramon
Estimation of grapevine vigour using mobile proximal sensors can provide an indirect method for determining grape yield and quality. Of the various indexes related to the characteristics of grapevine foliage, the leaf area index (LAI) is probably the most widely used in viticulture. To assess the feasibility of using light detection and ranging (LiDAR) sensors for predicting the LAI, several field trials were performed using a tractor-mounted LiDAR system. This system measured the crop in a transverse direction along the rows of vines and geometric and structural parameters were computed. The parameters evaluated were the height of the vines (H), the cross-sectional area (A), the canopy volume (V) and the tree area index (TAI). This last parameter was formulated as the ratio of the crop estimated area per unit ground area, using a local Poisson distribution to approximate the laser beam transmission probability within vines. In order to compare the calculated indexes with the actual values of LAI, the scanned vines were defoliated to obtain LAI values for different row sections. Linear regression analysis showed a good correlation (R 2 = 0.81) between canopy volume and the measured values of LAI for 1 m long sections. Nevertheless, the best estimation of the LAI was given by the TAI (R 2 = 0.92) for the same length, confirming LiDAR sensors as an interesting option for foliage characterization of grapevines. However, current limitations exist related to the complexity of data process and to the need to accumulate a sufficient number of scans to adequately estimate the LAI., This research was funded by ERDF (European Regional Development Fund) and the Spanish Ministry of Science and Education (Agreement No. AGL2002-04260-C04-02, and acronym PULVEXACT, and Agreement No. AGL2007-66093-C04-03, and acronym OPTIDOSA)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Characterisation of the LMS200 laser beam under the influence of blockage surfaces. Influence on 3D scanning of tree orchards

  • Sanz Cortiella, Ricardo
  • Llorens Calveras, Jordi
  • Rosell Polo, Joan Ramon
  • Gregorio López, Eduard
  • Palacín Roca, Jordi
The geometric characterisation of tree orchards is a high-precision activity comprising the accurate measurement and knowledge of the geometry and structure of the trees. Different types of sensors can be used to perform this characterisation. In this work a terrestrial LIDAR sensor (SICK LMS200) whose emission source was a 905-nm pulsed laser diode was used. Given the known dimensions of the laser beam cross-section (with diameters ranging from 12 mm at the point of emission to 47.2 mm at a distance of 8 m), and the known dimensions of the elements that make up the crops under study (flowers, leaves, fruits, branches, trunks), it was anticipated that, for much of the time, the laser beam would only partially hit a foreground target/object, with the consequent problem of mixed pixels or edge effects. Understanding what happens in such situations was the principal objective of this work. With this in mind, a series of tests were set up to determine the geometry of the emitted beam and to determine the response of the sensor to different beam blockage scenarios. The main conclusions that were drawn from the results obtained were: (i) in a partial beam blockage scenario, the distance value given by the sensor depends more on the blocked radiant power than on the blocked surface area; (ii) there is an area that influences the measurements obtained that is dependent on the percentage of blockage and which ranges from 1.5 to 2.5 m with respect to the foreground target/object. If the laser beam impacts on a second target/object located within this range, this will affect the measurement given by the sensor. To interpret the information obtained from the point clouds provided by the LIDAR sensors, such as the volume occupied and the enclosing area, it is necessary to know the resolution and the process for obtaining this mesh of points and also to be aware of the problem associated with mixed pixels., This research was funded by FEDER (Fondo Europeo de Desarrollo Regional) and the CICYT (Comisión Interministerial de Ciencia y Tecnología, Spain), under Agreement N, AGL2002-04260-C04-02 and AGL2010-22304-C04-03. LMS200 and SICK are trademarks of SICK AG, Germany.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

LIDAR and non-LIDAR-based canopy parameters to estimate the leaf area in fruit trees and vineyard

  • Sanz Cortiella, Ricardo
  • Llorens Calveras, Jordi
  • Escolà i Agustí, Alexandre
  • Arnó Satorra, Jaume
  • Planas de Martí, Santiago
  • Román, Carla
  • Rosell Polo, Joan Ramon
This paper is based on two initial hypotheses, firstly, it is proposed that the vegetation volume obtained with a LIDAR-based system or tree row LIDAR volume (TRLV) has a high correlation with the leaf area (LA). Secondly, it is proposed that the projected outer surface or projected tree row surface (PTRS), also LIDAR-based, is linearly related with the LA. The verification of these two hypotheses corresponds to the first two objectives of this work. The third objective is to propose an alternative method, without using LIDAR sensors, simpler and more economical, for in situ LA evaluation. To achieve these objectives a total of 17 blocks of pear, 14 of apple and 26 of vine, in different phenological states, were LIDAR scanned and subsequently manually defoliated. After the field and calculation work, the TRLV and LA were compared. The logarithmic regressions obtained had high correlations. For apple and pear trees the equations are practically the same with R2 of 0.85 and 0.84, respectively. The equation corresponding to vines is somewhat different and has an R2 of 0.86. The regression without species differentiation is 3.66ln(x) +9.65 with R2=0.90. Based on the TRLV, the front and top projected surface areas of each block were then obtained and, using these variables, the PTRS. The linear regressions obtained between PTRS and LA have high correlations with R2 of 0.88, 0.85 and 0.80 for apple trees, pear trees, and vineyard respectively. The three crops show very similar behavior. The straight lines are very close, with very similar slopes. With no species differentiation the linear regression model is y=1.47x - 1.18 with R2=0.93. The starting point of the third objective is to obtain the projected surfaces, frontal and top, without using a LIDAR sensor. These surfaces are not as precise as those obtained with LIDAR and for this reason they are referred to as 'estimated' projected surfaces. To calculate the estimated PTRS without a LIDAR sensor, the height and depth of the vegetation are measured with a tape measure. It is also necessary to make a visual estimation of the frontal gap-fraction. For this, a training method with known gap-fraction pictograms is proposed. The final results with this non-LIDAR method are very similar to those obtained with LIDAR. This method, although it needs human intervention, is simple, easy, economical and precise for in situ LA estimation., This research was partially funded by the Spanish Ministry of Economy and Competitiveness (projects AGL2002-04260-C04-02, AGL2007-66093-C04-03, AGL2010-22304-C04-03 and AGL2013- 48297-C2-2-R) and EU FEDER. Funding of Secretaria d’Universitats i Recerca del Departament d’Empresa i Coneixement de la Generalitat de Catalunya under Grant 2017 SGR 646 is also thanked.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Innovative LIDAR 3D dynamic measurement system to estimate fruit-tree leaf area

  • Sanz Cortiella, Ricardo
  • Llorens Calveras, Jordi
  • Escolà i Agustí, Alexandre
  • Arnó Satorra, Jaume
  • Ribes Dasi, Manuel
  • Masip Vilalta, Joan
  • Camp, Ferran
  • Gràcia Aguilà, Felipe José
  • Solanelles Batlle, Francesc
  • Planas de Martí, Santiago
  • Pallejà Cabrè, Tomàs
  • Palacín Roca, Jordi
  • Gregorio López, Eduard
  • Del Moral Martínez, Ignacio
  • Rosell Polo, Joan Ramon
In this work, a LIDAR-based 3D Dynamic Measurement System is presented and evaluated for the geometric characterization of tree crops. Using this measurement system, trees were scanned from two opposing sides to obtain two three-dimensional point clouds. After registration of the point clouds, a simple and easily obtainable parameter is the number of impacts received by the scanned vegetation. The work in this study is based on the hypothesis of the existence of a linear relationship between the number of impacts of the LIDAR sensor laser beam on the vegetation and the tree leaf area. Tests performed under laboratory conditions using an ornamental tree and, subsequently, in a pear tree orchard demonstrate the correct operation of the measurement system presented in this paper. The results from both the laboratory and field tests confirm the initial hypothesis and the 3D Dynamic Measurement System is validated in field operation. This opens the door to new lines of research centred on the geometric characterization of tree crops in the field of agriculture and, more specifically, in precision fruit growing., This work has been funded by the Spanish Ministry of Science and Innovation and by the European Union through the FEDER funds and is part of the research projects Pulvexact (AGL2002-04260-C04-02), Optidosa (AGL2007-66093-C04-03) and Safespray (AGL2010-22304-C04-03).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Performance of an ultrasonic ranging sensor in apple tree canopies

  • Escolà i Agustí, Alexandre
  • Planas de Martí, Santiago
  • Rosell Polo, Joan Ramon
  • Pomar Gomà, Jesús
  • Camp, Ferran
  • Solanelles Batlle, Francesc
  • Gràcia, Felip
  • Llorens Calveras, Jordi
  • Gil Moya, Emilio
Electronic canopy characterization is an important issue in tree crop management. Ultrasonic and optical sensors are the most used for this purpose. The objective of this work was to assess the performance of an ultrasonic sensor under laboratory and field conditions in order to provide reliable estimations of distance measurements to apple tree canopies. To this purpose, a methodology has been designed to analyze sensor performance in relation to foliage ranging and to interferences with adjacent sensors when working simultaneously. Results show that the average error in distance measurement using the ultrasonic sensor in laboratory conditions is ±0.53 cm. However, the increase of variability in field conditions reduces the accuracy of this kind of sensors when estimating distances to canopies. The average error in such situations is ±5.11 cm. When analyzing interferences of adjacent sensors 30 cm apart, the average error is ±17.46 cm. When sensors are separated 60 cm, the average error is ±9.29 cm. The ultrasonic sensor tested has been proven to be suitable to estimate distances to the canopy in field conditions when sensors are 60 cm apart or more and could, therefore, be used in a system to estimate structural canopy parameters in precision horticulture., This work has been funded by the Spanish Ministry of Science and Innovation and by the European Union through the FEDER funds and is part of research projects Pulvexact (AGL2002-04260-C04-02), Optidosa (AGL2007-66093-C04-03) and Safespray (AGL2010-22304-C04-03).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Pesticide dose adjustment in fruit and grapevine orchards by DOSA3D: Fundamentals of the system and on-farm validation

  • Román, Carla
  • Peris Giner, Miquel
  • Esteve, Joan
  • Tejerina, Miguel
  • Cambray, Jordi
  • Vilardell i Coderch, Pere
  • Planas de Martí, Santiago
Agricultural productivity cannot be sustained without the application of plant protection measures. Within the framework of integrated pest management (IPM), the use of chemical pesticides should be limited to the last option among the available practices. Even though their use remains common, it carries associated environmental and human health risks. One of the most accepted practices within IPM is the reduction of spraying events and/or pesticide applied doses. DOSA3D is a decision support system that allows the dose to be adjusted to the specific treatment scenario. For this, DOSA3D calculates the optimal application volume rate by estimating the leaf area index and takes into account the overall spraying efficiency and the pest or disease to be controlled. The system adopts specific minimum volume rates for fruit trees and vineyards without compromising the crop health status. To establish the adjusted dose, the labeled or the adviser prescription concentration is kept. Resulting adjusted doses provided by DOSA3D achieved pesticide savings up to 53% in fruit trees and 60% in vineyards. DOSA3D has been validated against the main diseases and pests of fruit trees and vineyards: brown spot and psylla in pear orchards; alternaria blotch disease, apple scab, codling moth, oriental moth and red spider mite in apple orchards; powdery mildew, brown rot, aphids, thrips and mites in peach orchards; and, powdery mildew, yellow spider mite and leafhoppers in grapevine orchards. In addition, a methodology called Green Way is presented to provide consistent and crop safety pesticide doses when these are labeled as concentration or ground area doses., his study wasfinanced by the EU Horizon 2020 project EUCLID[grant number 633999], the Spanish Ministry of Economy and Compet-itiveness project AgVance [AGL2013-48297-C2-2-R] and the SpanishMinistry of Agriculture, Fisheries and Food project GOPHYTOVID [con-tract 2018002001192]. We are also grateful for funding by theSecretaria d'Universitats i Recerca del Departament d'Empresa iConeixement de la Generalitat de Catalunya under Grant 2017 SGR 646
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A tractor-mounted scanning LIDAR for the non-destructive measurement of vegetative volume and surface area of tree-row plantations: a comparison with conventional destructive measurements

  • Rosell Polo, Joan Ramon
  • Sanz Cortiella, Ricardo
  • Llorens Calveras, Jordi
  • Arnó Satorra, Jaume
  • Escolà i Agustí, Alexandre
  • Ribes Dasi, Manuel
  • Masip Vilalta, Joan
  • Camp, Ferran
  • Gràcia, Felip
  • Solanelles Batlle, Francesc
  • Pallejà Cabrè, Tomàs
  • Val, Luis
  • Planas de Martí, Santiago
  • Gil Moya, Emilio
  • Palacín Roca, Jordi
The use of a low-cost tractor-mounted scanning Light Detection and Ranging (LIDAR) system for capable of making non-destructive recordings of tree-row structure in orchards and vineyards is described. Field tests consisted of several LIDAR measurements on both sides of the crop row, before and after defoliation of selected trees. Summary parameters describing the tree-row volume and the total crop surface area viewed by the LIDAR (expressed as a ratio with ground surface area) were derived using a suitable numerical algorithm. The results for apple and pear orchards and a wine producing vineyard were shown to be in reasonable agreement with the results derived from a destructive leaf sampling method. Also, good correlation was found between manual and sensor-based measurements of the vegetative volume of tree-row plantations. The Tree Area Index parameter, TAI, gave the best correlation between destructive and non-destructive (i.e. LIDAR-based) determinants of crop leaf area. The LIDAR system proved to be a powerful technique for low cost, prompt and non-destructive estimates of the volume and leaf-area characteristics of plants., This research was funded by the CICYT (Comisión Interministerial de Ciencia y Tecnología, Spain), under Agreement No. AGL2002-04260-C04-02.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Pesticide dose adjustment in fruit and grapevine orchards by DOSA3D: Fundamentals of the system and on-farm validation

  • Román, Carla
  • Peris, Miquel
  • Esteve, Joan
  • Tejerina, Miguel
  • Cambray, Jordi
  • Vilardell, Pere
  • Planas, Santiago
Agricultural productivity cannot be sustained without the application of plant protection measures. Within the framework of integrated pest management (IPM), the use of chemical pesticides should be limited to the last option among the available practices. Even though their use remains common, it carries associated environmental and human health risks. One of the most accepted practices within IPM is the reduction of spraying events and/or pesticide applied doses. DOSA3D is a decision support system that allows the dose to be adjusted to the specific treatment scenario. For this, DOSA3D calculates the optimal application volume rate by estimating the leaf area index and takes into account the overall spraying efficiency and the pest or disease to be controlled. The system adopts specific minimum volume rates for fruit trees and vineyards without compromising the crop health status. To establish the adjusted dose, the labeled or the adviser prescription concentration is kept. Resulting adjusted doses provided by DOSA3D achieved pesticide savings up to 53% in fruit trees and 60% in vineyards. DOSA3D has been validated against the main diseases and pests of fruit trees and vineyards: brown spot and psylla in pear orchards; alternaria blotch disease, apple scab, codling moth, oriental moth and red spider mite in apple orchards; powdery mildew, brown rot, aphids, thrips and mites in peach orchards; and, powdery mildew, yellow spider mite and leafhoppers in grapevine orchards. In addition, a methodology called Green Way is presented to provide consistent and crop safety pesticide doses when these are labeled as concentration or ground area doses., info:eu-repo/semantics/publishedVersion
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Relationship between tree row LIDAR-volume and leaf area density for fruit orchards and vineyards obtained with a LIDAR 3D Dynamic Measurement System

  • Sanz Cortiella, Ricardo
  • Rosell Polo, Joan Ramon
  • Llorens Calveras, Jordi
  • Gil Moya, Emilio
  • Planas de Martí, Santiago
In this work, a LIDAR 3D Dynamic Measurement System, based on a Two-Dimensional Terrestrial Laser-LIDAR Scanner (2D TLS), was used for the geometric characterisation of tree-row crops (apple trees, pear trees and vineyards). The trees were scanned with the LIDAR system from opposite sides to obtain two three-dimensional point clouds. The point clouds were registered and the volume occupied by the resulting point cloud, tree row LIDAR-volume (TRLV), was graphically and numerically obtained. The study undertaken in this paper is based on the hypothesis that there may exist a non-linear relationship between the TRLV and the leaf area density (LAD). The main objective is to examine the relationship between TRLV and LAD in vineyards, apple and pear orchards. The study of 35 blocks of vegetation reveals a good logarithmic fit, y = −0.36 ln(x) + 3.69 with R2 = 0.87, between the TRLV (x) in dm3 and the LAD (y) in dm−1. It would appear that the TRLV of the crops under study (planted in a hedgerow-type configuration) is in itself an explanation of the LAD. The competition for light between the leaves and the space that these leaves occupy appear to follow a similar model in the three crops. According to the results of this study, the LAD can be estimated from the TRLV. If the LAD is multiplied by the TRLV, the leaf area of the vegetation under study can be obtained. It is therefore concluded that by using the information provided by the LIDAR 3D Dynamic Measurement System, a good estimation can be obtained of the leaf area in hedgerow fruit tree crops and hedgerow vineyards., This work has been funded by the Spanish Ministry of Science and Innovation and by the European Union through the FEDER funds and is part of research projects Pulvexact (AGL2002-04260-C04-02), Optidosa (AGL2007-66093-C04-03) and Safespray (AGL2010-22304-C04-03).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Obtaining the three-dimensional structure of tree orchards from remote 2D terrestrial LIDAR scanning

  • Rosell Polo, Joan Ramon
  • Llorens Calveras, Jordi
  • Sanz Cortiella, Ricardo
  • Arnó Satorra, Jaume
  • Ribes Dasi, Manuel
  • Masip Vilalta, Joan
  • Escolà i Agustí, Alexandre
  • Camp, Ferran
  • Solanelles Batlle, Francesc
  • Gràcia, Felip
  • Gil Moya, Emilio
  • Val, Luis
  • Planas de Martí, Santiago
  • Palacín Roca, Jordi
In recent years, LIDAR (light detection and ranging) sensors have been widely used to measure environmental parameters such as the structural characteristics of trees, crops and forests. Knowledge of the structural characteristics of plants has a high scientific value due to their influence in many biophysical processes including, photosynthesis, growth, CO2-sequestration and evapotranspiration, playing a key role in the exchange of matter and energy between plants and the atmosphere, and affecting terrestrial, above-ground, carbon storage. In this work, we report the use of a 2D LIDAR scanner in agriculture to obtain three-dimensional (3D) structural characteristics of plants. LIDAR allows fast, non-destructive measurement of the 3D structure of vegetation (geometry, size, height, cross-section, etc.). LIDAR provides a 3D cloud of points, which is easily visualized with Computer Aided Design software. Three-dimensional, high density data are uniquely valuable for the qualitative and quantitative study of the geometric parameters of plants. Results are demonstrated in fruit and citrus orchards and vineyards, leading to the conclusion that the LIDAR system is able to measure the geometric characteristics of plants with sufficient precision for most agriculture applications. The developed system made it possible to obtain 3D digitalized images of crops, from which a large amount of plant information – such as height, width, volume, leaf area index and leaf area density – could be obtained. There was a great degree of concordance between the physical dimensions, shape and global appearance of the 3D digital plant structure and the real plants, revealing the coherence of the 3D tree model obtained from the developed system with respect to the real structure. For some selected trees, the correlation coefficient obtained between manually measured volumes and those obtained from the 3D LIDAR models was as high as 0.976., This research was funded by the CICYT (Comisión Interministerial de Ciencia y Tecnología, Spain), under Agreement No. AGL2002-04260-C04-02. LMS200 and SICK are trademarks of SICK AG, Germany.