Pasar al contenido principal

EL HORMIGON DE FIBRAS DE ACERO COMO SUPERACION DEL HORMIGON TRADICIONAL Y SUS PERSPECTIVAS DE FUTURO

BIA2009-12722

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2009
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Splitting of concrete cover in steel fiber reinforced concrete: Semi-empirical modeling and minimum confinement requirements

  • García Taengua, Emilio José
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
The use of steel fiber reinforced concrete (SFRC) is becoming more and more common. Concerning bond of rebars to concrete, fibers provide passive confinement and not only improve bond performance but also affect the mode of bond failure. To analyze these aspects, a series of prismatic specimens have been subjected to the Pull Out Test, and an accurate model for predicting the mode of bond failure has been developed. The following factors have been considered: concrete compressive strength (30 50 MPa), rebar diameter (8 20 mm), concrete cover (between 30 mm and 5 times rebar diameter), fiber content (up to 70 kg/m3), and fiber slenderness and length. This model relates splitting probability to the factors considered. It has been proved that increasing fiber content restrains the risk of splitting failure. The favorable effect of fibers when preventing splitting failures has been revealed to be more important for higher concrete compressive strength values, which require higher concrete cover/diameter ratios for splitting failure to be prevented. Fiber slenderness and fiber length modify the effect of fiber content on splitting probability and therefore on minimum cover/diameter ratios required to prevent splitting failures., The authors of this work wish to thank both the Research Bureau of the Spanish Ministry of Science and Innovation and the 'Plan E' programme for the funding of the project 'BIA 2009-12722', this research being a part thereof.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Size Effect on Strand Bond and Concrete Strains at Prestress Transfer

  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • Caro Forero, Libardo Andrés
[EN] The size-effect phenomenon has been analyzed with pretensioned prestressed concrete prismatic specimens at prestress transfer. An experimental program that includes variables such as concrete mixture design, specimen cross section size, and concrete age, has been conducted. Several series of specimens with different embedment lengths have been made and tested using a testing technique based on the bond behavior analysis by measuring prestressing strand force. In addition, some specimens have been instrumented to determine longitudinal concrete strain profiles. The tests have provided data on concrete strains, transfer length, effective prestressing force, bond stress, and concrete modulus of elasticity. Relationships between measured prestressing strand forces and effective prestressing forces obtained from concrete compressive strains have been found. A coefficient to account for the specimen crosssection size-effect on the concrete modulus of elasticity has been proposed. Comparisons between test results and theoretical predictions from pre-existing equations in the codes have been made., Funding for this research has been provided by the Spanish Ministry of Education and Science, the Ministry of Science and Innovation, and ERDF (Projects BIA2006-05521 and BIA2009-12722).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Shear behavior of prestressed precast beams made of self-compacting fiber reinforced concrete

  • Cuenca Asensio, Estefanía
  • Serna Ros, Pedro|||0000-0001-8754-1165
Even after many years of in-depth research the shear behavior of concrete structures is still a subject for debate. Current Design Codes need to be adapted to new materials and production methods. This paper discusses some still unresolved doubts, based on an experimental program consisting of nine prestressed l-beams of different flange dimensions. Shear evaluation is analyzed in accordance with the Codes under different conditions: a combination of fibers with stirrups, the possible influence of flange width on shear strength and the interaction of fibers with other important parameters such as flange width and longitudinal reinforcement. The results obtained show that fibers act as additional reinforcement to stirrups and also that the Codes are within the safety limits as regards shear ultimate limit state (ULS). (C) 2013 Elsevier Ltd. All rights reserved., The authors of this work wish to thank the Research Bureau of the Spanish Ministry of Science and Innovation and Plan-E, for funding of Project BIA 2009-12722. We are also grateful for the collaboration of the precast manufacturer PREVALESA S.L.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Prestress losses evaluation in prestressed concrete prismatic specimens

  • Caro Forero, Libardo Andrés
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
This paper presents an experimental research work to evaluate prestress losses in pretensioned prestressed concrete. An experimental program including variables such as concrete mix design, specimen cross-section size and concrete age at the prestress transfer was carried out. Several pretensioned prestressed concrete prismatic specimens were made and tested using the ECADA+ test method, based on measuring prestressing reinforcement force. In addition, specimens were instrumented to obtain the longitudinal concrete strains profiles at any time. Measurements from both techniques were taken over 1 year. Measured prestress losses included elastic shortening losses and time-dependent losses due to concrete shrinkage and creep. A coefficient to account for the relationship between the prestress losses from the measured prestressing forces and the actual prestress losses from concrete compressive strains is proposed. The experimental results were compared with the predicted prestress losses using methods from several codes., Funding for this experimental research work has been provided by the Spanish Ministry of Education and Science and ERDF (Project BIA2006-05521 and Project BIA2009-12722). Tests have been conducted at the Institute of Concrete Science and Technology (ICI-TECH), at the Universitat Politecnica de Valencia (Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An inverse analysis method based on deflection to curvature transformation to determine the tensile properties of UHPFRC

  • López Martínez, Juan Ángel
  • Camacho Torregrosa, Esteban Efraím
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
[EN] The determination of the tensile properties of such a deflection hardening response material as UHPFRC is a serious challenge for both researchers and designers. This process involves many factors, such as specimen size, fibre orientation or test typology. The socalled inverse analysis is used to obtain the tensile constitutive properties that are consistent with the specimen response in a bending test. This work focuses on the inverse analysis process. The main aim is to develop a new back-calculation methodology, which is easy to implement, reliable, quick and is consistentwith the measurements taken from a four-point bending test. The new methodology proposed has been validated using an analytical formulation and the experimental results of others authors. This paper also includes an application example of how this methodology works., This work forms part of the ‘‘FIBAC’’ and ‘‘FISNE’’ research projects, with reference BIA2009-12722 and BIA2012-35776, respectively, supported by the Spanish Ministry of Economy and Competiveness and the FEDER fund. Support for this project is gratefully acknowledged. We also wish to thank the Universitat Polite`cnica de Vale`ncia for its Excellence Scholarship (PAID-09-11), the Spanish Ministry of Education, Culture and Sport for its FPU scholarship programme, and also Mr. Toshiyuki Kanakubo for his friendly treatment and help.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

First Ultra-High-Performance Fibre- Reinforced Concrete Footbridge in Spain: Design and Construction

  • López Martínez, Juan Ángel
  • Camacho Torregrosa, Esteban Efraím
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • Coll Carrillo, Hugo
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
[EN] Ultra-high-performance fibre-reinforced concrete (UHPFRC) is defined as a cement-based composite material that combines three technical advances in concrete: high compressive strength, presence of steel fibres and flowability. Since UHPFRC is a very expensive material, in order that UHPFRC can be considered as a competitive alternative in structural applications, it is necessary to optimise the design of structural systems. This process leads to UHPFRC lightweight structures that minimise the concrete needs and give solutions more similar to steel than concrete. The innovative design of the 43,5 m span footbridge, constructed only with UHPFRC and placed over the Ovejas ravine in Alicante, Spain, is presented in this paper. The new UHPFRC footbridge has replaced the former design devised in steel due to many factors such as lower construction and maintenance costs, high durability in aggressive environment close to the sea leading to an increase in service life and its aesthetic enhancement. This paper covers several issues about the design and construction of this singular footbridge, such as design justification, structural evaluation, UHPFRC mix design, quality control and construction process at all stages. The static and dynamic load tests performed are also presented. The footbridge over the Ovejas ravine has become the first structure constructed with UHPFRC in Spain, and as far as we know, it is the first truss pedestrian footbridge made only of UHPFRC in the world., This work has been developed under both "FIBAC" and "FISNE" research projects, with references BIA2009-12722 and BIA2012-35776, supported by the Spanish Ministry of Science and Innovation. Support for this project is gratefully acknowledged. The authors also wish to thank Generalitat Valenciana and the Spanish Ministry of Education, Culture and Sport for its FPU scholarship program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Slip distribution model along the anchorage length of prestressing strands

  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • Hale, WM
  • García Taengua, Emilio José
An analytical model to predict strand slips within both transmission and anchorage lengths in pretensioned prestressed concrete members is presented. This model has been derived from an experimental research work by analysing the bond behavior and determining the transmission and anchorage lengths of seven-wire prestressing steel strands in different concrete mixes. A testing technique based on measuring the prestressing strand force in specimens with different embedment lengths has been used. The testing technique allows measurement of free end slip as well as indirect determination of the strand slip at different cross sections of a member without interfering with bond phenomena. The experimental results and the proposed model for strand slip distribution have been compared with theoretical predictions according to different equations in the literature and with experimental results obtained by other researchers., The content of the present paper is based on tests which were conducted in the Institute of Concrete Science and Technology (ICI-TECH), at Universitat Politecnica of Valencia (Spain), in collaboration with the companies PREVALESA and ISOCRON. Funding for this experimental research work was provided by the Spanish Ministry of Education and Science/Science and Innovation and ERDF (Project BIA2006-05521 and Project BIA2009-12722). The authors wish to thank the above companies as well as the concrete structures laboratory technicians at the Universitat Politecnica of Valencia for their cooperation. Finally, the authors also wish to pay their respects to C.A. Arbelaez.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Measuring specific parameters in pretensioned concrete members using a single testing technique

  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • García Taengua, Emilio José
  • Caro Forero, Libardo Andrés
Pretensioned concrete members are designed and manufactured by using at least two materials: concrete and prestressing reinforcement. Also, two main stages must be considered: prestress transfer and member loading. Hence, the behavior of these members depends strongly on the reinforcement-to-concrete bond performance and prestress losses. In this paper, a testing technique to measure the specific parameters related with the involved phenomena is presented. The testing technique is based on the analysis of series of specimens varying in embedment length to simulate several cross sections at only one end of a pretensioned concrete member. Each specimen is characterized by means of the sequential release of the prestress transfer (detensioning) and the pull-out (loading) operation. The test provides data on prestressing force, transmission length (initial and long-term), anchorage length (without and with slip), reinforcement slips, bond stresses, longitudinal concrete strains, concrete modulus of elasticity, and prestress losses (instantaneous and time-dependent)., The content of this paper is part of the research that the Institute of Concrete Science and Technology (ICITECH) at Universitat Politecnica de Valencia is currently conducting in conjunction with PREVALESA and ISOCRON. This study has been funded by the Ministry of Education and Science/ Science and Innovation and ERDF (Projects BIA2006-05521 and BIA2009-12722). The authors wish to thank the aforementioned companies as well as the technicians at the concrete structures laboratory of the Universitat Politecnica de Valencia for their cooperation. Finally, the authors wish to pay their respects to C.A. Arbelaez.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bond of Reinforcement in Concrete Applied to Concrete Quality Control: The Bottle Bond Test

  • García Taengua, Emilio José
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
This paper presents the results of an experimental research dealing with bond strength as a parameter for concrete quality control. To this end, a low-cost testing technique has been developed: the Bottle Bond Test (BBT). Specimens for the BBT are produced by casting concrete into empty plastic bottles (used as moulds) with a reinforcing bar longitudinally centred. The result is a bottle-shaped concrete specimen with an embedded rebar, which is pulled out to determine bond strength. Different parameters related to this test setup modify bond strength: their effect has been analyzed. An equation to relate the obtained bond strength values to concrete compressive strength is presented. This equation has been validated with real production data from a readymix concrete plant. Its accuracy and therefore the feasibility of BBT for concrete quality control have been verified. Therefore, the BBT can be an alternative to conventional concrete quality based on uniaxial compression tests., The authors of this work wish to thank both the Research Bureau of the Spanish Ministry of Science and Innovation and the 'Plan E' programme for the funding of the project 'BIA 2009-12722', this research being a part thereof.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bond of reinforcing bars to steel fiber reinforced concrete

  • García Taengua, Emilio José
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
Steel fiber reinforced concrete (SFRC) has been increasingly used during recent years. Regarding bond of rebars to concrete, fibers provide passive confinement and improve bond capacity in terms of bond strength and, more importantly, toughness. An extensive experimental programme has been carried out, and SFRC specimens with embedded rebars have been subjected to the Pull Out Test to obtain the bond stress slip curves, retaining the bond strength and the area under the curve as measures of the bond capacity of concrete. The following parameters were considered: concrete compressive strength (30-50 MPa), rebar diameter (8-20 mm), concrete cover (between 30 mm and 5 times rebar diameter), fiber content (up to 70 kg/m(3)), and the slenderness and length of the steel fibers used. Predictive equations have been obtained to relate the experimental results to the factors considered, and the trends observed have been analyzed and discussed. (C) 2015 Elsevier Ltd. All rights reserved., The authors of this work wish to thank both the Research Bureau of the Spanish Ministry of Science and Innovation for the funding of the projects 'BIA 2009-12722' and 'BIA 2012-35776-AR', this research being a part thereof.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of concrete composition on anchorage bond behavior of prestressing reinforcement

  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • García Taengua, Emilio José
An experimental research addressing the effects of concrete composition and strength on anchorage bond behavior of prestressing reinforcement is presented to clarify the effect of material properties that have appeared contradictory in previous literature. Bond stresses and anchorage lengths have been obtained in twelve concrete mixes made up of different cement contents (C) - 350 to 500 kg/m(3) - and water/cement (w/c) ratios - 0.3 to 0.5 - with compressive strength at 24 h ranging from 24 to 55 MPa. A testing technique based on measuring the prestressing force in specimens with different embedment lengths has been used. The results show that anchorage length increases when w/c increases, more significantly when C is higher; the effect of C reveals different trends based on w/c. The obtained anchorage bond stresses are greater for higher concrete compressive strength, and their average ratio of 1.45 with respect to transmission bond stresses implies a potential bond capacity. (C) 2013 Elsevier Ltd. All rights reserved., The content of this article is part of the research that the Institute of Concrete Science and Technology (ICITECH) at Universitat Politecnica de Valencia is currently conducting in conjunction with PREVALESA and ISOCRON. This study has been funded by the Ministry of Education and Science/Science and Innovation and ERDF (Projects BIA2006-05521 and BIA2009-12722). The authors wish to thank the aforementioned companies as well as the technicians at the concrete structures laboratory of the Universitat Politecnica de Valencia for their cooperation. Finally, the authors wish to pay their respects to C.A. Arbelaez.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Failure modes and shear design of prestressed hollow core slabs made of fiber-reinforced concrete

  • Cuenca Asensio, Estefanía
  • Serna Ros, Pedro|||0000-0001-8754-1165
Hollow core slabs (HCS) are usually precast by extrusion and it is not easy to place stirrups; thus, it is difficult to guarantee shear resistance in some cases. This paper describes an experience using fiber-reinforced concrete (FRC) to produce HCS by extrusion to gain shear reinforcement. An experimental program consisting of 26 HCS was developed. Elements were produced and tested in shear according to the following variables: amount of steel fibers (0, 50 and 70 kg/m(3)) and a shear span/depth (a/d) ratio of 2.3-4.4 and 8.6. Different failure modes took place. Some of the main conclusions drawn were that fibers improve quality of the material for shear, HCS with fibers achieved greater loads than HCS without fiber reinforcement and with a more ductile behavior. (c) 2012 Elsevier Ltd. All rights reserved., The authors of this work wish to thank the research bureau of the Spanish Ministry of Science and Innovation and the Plan E, for the funding of the project "BIA 2009-12722". The collaboration of the precast industry "PREVALESA S.L." is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Time-dependent evolution of strand transfer length in pretensioned prestressed concrete members

  • Caro Forero, Libardo Andrés
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
For design purposes, it is generally considered that prestressing strand transfer length does not change with time. However, some experimental studies on the effect of time on transfer lengths show contradictory results. In this paper, an experimental research to study transfer length changes over time is presented. A test procedure based on the ECADA testing technique to measure prestressing strand force variation over time in pretensioned prestressed concrete specimens has been set up. With this test method, an experimental program that varies concrete strength, specimen cross section, age of release, prestress transfer method, and embedment length has been carried out. Both the initial and long-term transfer lengths of 13-mm prestressing steel strands have been measured. The test results show that transfer length variation exists for some prestressing load conditions, resulting in increased transfer length over time. The applied test method based on prestressing strand force measurements has shown more reliable results than procedures based on measuring free end slips and longitudinal strains of concrete. An additional factor for transfer length models is proposed in order to include the time-dependent evolution of strand transfer length in pretensioned prestressed concrete members. © 2012 Springer Science+Business Media Dordrecht., Funding for this experimental research work has been provided by the Spanish Ministry of Education and Science and ERDF (Projects BIA2006-05521 and BIA2009-12722). Tests have been conducted at the Institute of Concrete Science and Technology (ICITECH), at the Universitat Politecnica de Valencia (Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of concrete matrix and type of fiber on the shear behavior of self-compacting fiber reinforced concrete beams

  • Cuenca Asensio, Estefanía
  • Echegaray-Oviedo, J.
  • Serna Ros, Pedro|||0000-0001-8754-1165
Steel fibers are known to improve shear behavior. The Design Codes (Eurocode 2 (EC2), Spanish EHE-08, Model Code 2010 and RILEM approach) have developed formulas to calculate the fiber contribution to shear, mainly focused on standard FRCs, i.e. medium strength concretes with a low content of normal strength steel fibers. However, in real applications other combinations are possible, such as high or medium strength concretes with high strength steel fibers of different lengths and geometry. An experimental program consisting of 12 self-compacting fiber reinforced concrete (SCFRC) I-type beams was carried out. All the beams had the same geometry and fiber content (50 kg/m3), and they were made with two different concrete compressive strength values and five different types of steel fibers and were tested for shear. The main conclusions reached were that the type of fiber substantially affects shear behavior, even when the Design Code formulas indicate similar contributions. The combination of high strength concrete matrixes with low strength fibers does not seem to be efficient. Also, the use of high residual flexural tensile strength values (e.g. fR3 or fR4) does not appear to be the most accurate reference value to calculate the beam shear strength in these cases. The present Design Codes consider standard FRCs, but their formulas should be revised for concretes with fibers of different strengths, slenderness and geometry, since these properties substantially affect shear behavior., The authors wish to thank the research bureau of the Spanish Ministry of Science and Innovation and Plan E, for funding from Project BIA 2009-12722. The beams used in the study were cast and tested at the Universitat Politecnica de Valencia (Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental Technique for Measuring the Long-term Transfer Length in Prestressed Concrete

  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • Caro Forero, Libardo Andrés
This article presents a proposal of a test set-up and methodology for testing the transfer length evolution through time of prestressing reinforcement in pretensioned prestressed concrete members, aimed at providing a basis for standardization. The proposed test method is based on the instantaneous and time-related analysis of the prestressing reinforcement force profile at only one end of a pretensioned prestressed concrete member. The basis of the test method and the requirements of the prestressing frame and its components are presented, as well as the test procedure stages and the measurement devices. The interpretation of the test results and the criteria to determine both the initial and the long-term transfer lengths are explained. A test method application and the equipment for testing seven-wire prestressing strands have been designed. Some experimental results are provided to validate the test. A comparative analysis of test reliability with other existing experimental methods is also included. © 2012 Wiley Publishing Ltd., Funding for this experimental research work was provided by the Spanish Ministry of Education and Science and ERDF (Projects BIA2006-05521 and BIA2009-12722). Tests were conducted in the Institute of Concrete Science and Technology (ICITECH), Universitat Politecnica de Valencia (Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Test Method to Characterize Flexural Creep Behaviour of Pre-cracked FRC Specimens

  • Arango Campo, Samuel Eduardo
  • García Taengua, Emilio José
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
[EN] This paper presents a proposal of test setup and methodology for testing the flexural creep behaviour of pre-cracked Fibre Reinforced Concrete (FRC) specimens, aimed at providing a basis for standardization. The design criteria used to define the equipment and methodology are presented. A test results sheet and a curve are established to present the results of creep tests, and some experimental results are shown so that the test can be validated. The equipment and methodology proposed make it possible to research the influence of factors such as concrete type, fibres type and content, applied load, and crack opening value. © 2011 Society for Experimental Mechanics., The present study was supported by the Spanish Universitat Politecnica de Valencia (UPV), Valencia, Spain; by the project BIA 2009-12722 of the Spanish Ministry; and by the project "HABITAT 2030" [PS-380000-2008-11] funded by both the Spanish Ministry of Science and Innovation and the European Regional Development Found. The authors would like to express their gratitude for this support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Prediction of the transfer length of prestressing strands with neural networks

  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Yepes, V.|||0000-0001-5488-6001
  • FERRI RABASA, FRANCESC J
This paper presents a study on the prediction of transfer length of 13 mm seven-wire prestressing steel strand in pretensioned prestressed concrete members with rectangular cross-section including several material properties and design and manufacture parameters. To this end, a carefully selected database consisting of 207 different cases coming from 18 different sources spanning a variety of practical transfer length prediction situations was compiled. 16 single input features and 5 combined input features are analyzed. A widely used feedforward neural regression model was considered as a representative of several machine learning methods that have already been used in the engineering field. Classical multiple linear regression was also considered in order to comparatively assess performance and robustness in this context. The results show that the implemented model has good prediction and generalization capacity when it is used on large input data sets of practical interest from the engineering point of view. In particular, a neural model is proposed -using only 4 hidden units and 10 input variables- which significantly reduces in 30% and 60% the errors in transfer length prediction when using standard linear regression or fixed formulas, respectively., Funding for this study were received from the Spanish Ministry of Science and Innovation and ERDF (Research Project BIA2006-05521, BIA2009-12722, and BIA2011-23602) and from the Spanish Ministry of Education (TIN2009-14205-C04-03 and Consolider Ingenio 2010 CSD2007-00018), as well as the European Community with the FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Strand bond performance in prestressed concrete accounting for bondslip

  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • Hale, W. M.
This paper presents the results of an experimental research program addressing the bond behavior of prestressing strands in pretensioned prestressed concrete members after anchorage failure has occurred. A test methodology based on measuring the prestressing strand force and strand end slip at the specimens free end was employed. Transmission- and anchorage-length tests were performed on several series of prestressed specimens with different embedment lengths using twelve concrete mixes. Average bond stresses along the transmission length and the anchorage length were obtained for specimens with release strengths ranging from 24 MPa to 55 MPa. For the anchorage analysis, a parameter was developed that includes strand slip to be used in determining anchorage length. Based on the test results, an analysis to experimentally substantiate the Stress Waves Theory of Janney has been proposed. Additionally, the potential bond performance of prestressing strands after anchorage failure at the end regions has been suggested., The content of the present paper is based on tests which were conducted in the Institute of Concrete Science and Technology (ICITECH), at Universitat Politecnica of Valencia (Spain), in collaboration with the companies PREVALESA and ISOCRON. Funding for this experimental research work was provided by the Spanish Ministry of Education and Science/Science and Innovation and ERDF (Project BIA2006-05521 and Project BIA2009-12722). The authors wish to thank the above companies as well as the concrete structures laboratory technicians at the Universitat Politecnica of Valencia for their cooperation. Finally, the authors also wish to pay their respects to C.A. Arbelaez.