Pasar al contenido principal

MICROESTRUCTURA, DURABILIDAD Y RESISTENCIA A LA CORROSION DE HORMIGONES DE BAJO CONTENIDO EN CLINKER. ESTUDIO EN LABORATORIO Y EN AMBIENTES ATMOSFERICOS AGRESIVOS

BIA2011-25721

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2011
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSIDAD DE ALICANTE
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Impedance Spectroscopy Study of the Effect of Environmental Conditions on the Microstructure Development of Sustainable Fly Ash Cement Mortars

  • Ortega, José Marcos
  • Sánchez, Isidro
  • Climent, Miguel-Ángel
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
Today, the characterisation of the microstructure of cement-based materials using non-destructive techniques has become an important topic of study, and among them, the impedance spectroscopy has recently experienced great progress. In this research, mortars with two different contents of fly ash were exposed to four different constant temperature and relative humidity environments during a 180-day period. The evolution of their microstructure was studied using impedance spectroscopy, whose results were contrasted with mercury intrusion porosimetry. The hardening environment has an influence on the microstructure of fly ash cement mortars. On one hand, the impedance resistances R1 and R2 are more influenced by the drying of the materials than by microstructure development, so they are not suitable for following the evolution of the porous network under non-optimum conditions. On the other hand, the impedance spectroscopy capacitances C1 and C2 allow studying the microstructure development of fly ash cement mortars exposed to those conditions, and their results are in accordance with mercury intrusion porosimetry ones. Finally, it has been observed that the combined analysis of the abovementioned capacitances could be very useful for studying shrinkage processes in cement-based materials kept in low relative humidity environments.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Skin friction coefficient change on cement grouts for micropiles due to sulfate attack

  • Pastor Navarro, José Luis
  • Ortega, José Marcos
  • Climent, Miguel-Ángel
  • Sánchez, Isidro
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Pastor Navarro, José Luis|||/items/d54670cf-e108-40a1-9466-1cd07a1e614c
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
This paper presents a study of skin friction change of cement pastes used for micropiles as a geotechnical foundation when grout surface is affected by sulfate attack. In this research skin friction coefficient between cement paste – cement paste was measured, studying change in friction depending on the initial roughness of samples. Tests were performed after 3 and 6 months of immersion in a 15% Na2SO4 solution. Results show that sulfate attack increases skin friction coefficient for both surface finishes, concluding that this attack does not have a negative effect on friction in the experimental conditions of this work.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Influencia de diferentes condiciones de curado en la estructura porosa y en las propiedades a edades tempranas de morteros que contienen ceniza volante y escoria de alto horno, Influence of different curing conditions on the pore structure and the early age properties of mortars with fly ash and blast-furnace slag

  • Ortega, José Marcos
  • Sánchez, Isidro
  • Climent, Miguel-Ángel
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
En este trabajo se ha estudiado la evolución de la microestructura, propiedades de durabilidad y resistencias mecánicas de morteros preparados con cementos comerciales, que contienen ceniza volante (entre un 21% y un 35%) y escoria de alto horno (entre un 66% y un 80%), expuestos a tres ambientes, un ambiente óptimo de laboratorio, y dos ambientes representativos del clima Atlántico y Mediterráneo respectivamente. Como referencia de comportamiento, también se ensayaron morteros de cemento Portland. La microestructura se caracterizó mediante porosimetría de intrusión de mercurio. En lo referente a la durabilidad, se estudiaron los coeficientes de absorción capilar y de migración de cloruros en estado no estacionario. También se determinó la resistencia a compresión de los morteros. Los ensayos se realizaron a 7, 28 y 90 días. La principal conclusión alcanzada es que los cementos con cenizas y escorias expuestos a condiciones ambientales representativas de los climas Atlántico y Mediterráneo, pueden desarrollar unas propiedades en servicio adecuadas al cabo de tres meses.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Impedance spectroscopy study of the effect of environmental conditions in the microstructure development of OPC and slag cement mortars

  • Ortega, José Marcos
  • Sánchez, Isidro
  • Climent, Miguel-Ángel
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
In this work, the microstructure of mortars made with an ordinary Portland cement and slag cement has been studied. These mortars were exposed to four different constant temperature and relative humidity environments during a 180-day period. The microstructure has been studied using impedance spectroscopy, and mercury intrusion porosimetry as a contrast technique. The impedance spectroscopy parameters make it possible to analyze the evolution of the solid fraction formation for the studied mortars and their results are confirmed with those obtained using mercury intrusion porosimetry. The development of the pore network of mortars is affected by the environment. However, slag cement mortars are more influenced by temperature while the relative humidity has a greater influence on the OPC mortars. The results show that slag cement mortars hardened under non-optimal environments have a more refined microstructure than OPC mortars for the studied environmental conditions.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Durability and compressive strength of blast furnace slag-based cement grout for special geotechnical applications, Caracterización de las propiedades de durabilidad y resistencia a compresión de lechadas de cemento con escoria de alto horno para trabajos geotécnicos especiales

  • Ortega, José Marcos
  • Pastor Navarro, José Luis
  • Albaladejo Ruiz, Arturo
  • Sánchez, Isidro
  • Climent, Miguel-Ángel
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Pastor Navarro, José Luis|||/items/d54670cf-e108-40a1-9466-1cd07a1e614c
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
Special foundations, most prominently micropiles and soil anchors, are frequently used in construction today. In Spain, the grout for these special technical applications is generally prepared with portland cement, although the codes and standards in place stipulate only the minimum compressive strength required, with no mention of cement type. Those texts also establish a range of acceptable water:cement ratios. In the present study, durability and compressive strength in cement grout prepared with blast furnace slag cement at different w/c ratios are characterised and compared to the findings for a reference portland cement grout. The results show that slag grout exhibits greater durability than the portland cement material and complies with the compressive strength requirements laid down in the respective codes.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Effects of Environment in the Microstructure and Properties of Sustainable Mortars with Fly Ash and Slag after a 5-Year Exposure Period

  • Ortega, José Marcos
  • Tremiño Agulló, Rosa María
  • Sánchez, Isidro
  • Climent, Miguel-Ángel
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
Nowadays, getting a more environmentally sustainable cement production is one of the main goals of the cement industry. In this regard, the use of active additions, like fly ash and ground granulated blast-furnace slag, has become very popular. The behaviour, in the short-term, of cement-based materials with those additions is well-known when their hardening is produced under optimum conditions. However, real structures are exposed to different environments during long periods, which could affect the development of microstructures and the service properties of cementitious materials. The objective of this work is to analyse the effects in the long-term (up to 5 years approximately) produced by the exposure to different non-optimum laboratory conditions in the microstructure, mechanical and durability properties of mortars made with slag and fly ash commercial cements. Their performance was compared to that observed for ordinary Portland cement (OPC) mortars. The microstructure has been analysed using mercury intrusion porosimetry. The effective porosity, the capillary suction coefficient, the chloride migration coefficient and mechanical strengths were analysed too. According to the results, mortars prepared using slag and fly ash sustainable commercial cements, exposed to non-optimum conditions, show a good performance after 5-years hardening period, similar or even better than OPC mortars.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Moisture Distribution in Partially Saturated Concrete Studied by Impedance Spectroscopy

  • Sánchez, Isidro
  • Anton, Carlos
  • Vera Almenar, Guillem de
  • Ortega, José Marcos
  • Climent, Miguel-Ángel
  • Anton, Carlos|||/items/98677460-0003-4114-a75b-b2870605580a
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
  • Vera Almenar, Guillem de|||/items/7220bc28-fcb2-4f1c-a8d1-39c7e51b6652
The moisture content and its spatial distribution has a great influence on the durability properties of concrete structures. Several non-destructive techniques have been used for the determination of the total water content, but moisture distribution is difficult to determine. In this paper impedance spectroscopy is used to study the water distribution in concrete samples with controlled and homogeneously distributed moisture contents. The technique is suitable for the determination of water distribution inside the sample, using the appropriate equivalent circuits. It is shown that using the selected drying procedures there is no change in the solid phase of the samples, although the technique can only be used for the qualitative study of variations in the solid phase when samples are too thick. The results of this work show that for a wide range of concrete percentages of saturation, from full to 18 % saturation, practically all the pores keep at least a thin layer of electrolyte covering their walls, since the capacitance measurement results are practically independent of the saturation degree.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Performance of Sustainable Fly Ash and Slag Cement Mortars Exposed to Simulated and Real In Situ Mediterranean Conditions along 90 Warm Season Days

  • Ortega, José Marcos
  • Esteban Pérez, María Dolores
  • Sánchez, Isidro
  • Climent, Miguel-Ángel
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
Nowadays, cement manufacture is one of the most polluting worldwide industrial sectors. In order to reduce its CO2 emissions, the clinker replacement by ground granulated blast–furnace slag and fly ash is becoming increasingly common. Both additions are well-studied when the hardening conditions of cementitious materials are optimum. Therefore, the main objective of this research was to study the short-term effects of exposure, to both laboratory simulated and real in situ Mediterranean climate environments, on the microstructure and durability-related properties of mortars made using commercial slag and fly ash cements, as well as ordinary Portland cement. The real in situ condition consisted of placing the samples at approximately 100 m away from the Mediterranean Sea. The microstructure was analysed using mercury intrusion porosimetry. The effective porosity, the capillary suction coefficient and the non-steady state chloride migration coefficient were also studied. In view of the results obtained, the non-optimum laboratory simulated Mediterranean environment was a good approach to the real in situ one. Finally, mortars prepared using sustainable cements with slag and fly ash exposed to both Mediterranean climate environments, showed adequate service properties in the short-term (90 days), similar to or even better than those in mortars made with ordinary Portland cement.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Microstructural Effects of Sulphate Attack in Sustainable Grouts for Micropiles

  • Ortega, José Marcos
  • Esteban Pérez, María Dolores
  • Rodríguez Escribano, Raúl Rubén
  • Pastor Navarro, José Luis
  • Sánchez, Isidro
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Pastor Navarro, José Luis|||/items/d54670cf-e108-40a1-9466-1cd07a1e614c
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
Nowadays, the use of micropiles has undergone a great development. In general, they are made with cement grout, reinforced with steel tubing. In Spain, these grouts are prepared using OPC, although the standards do not forbid the use of other cements, like sustainable ones. Micropiles are in contact with soils and groundwater, in which the presence of sulphates is common. Their deleterious effects firstly affect to the microstructure. Then, the aim of this research is to study the effects of sulphate attack in the microstructure of micropiles grouts, prepared with OPC, fly ash and slag commercial cements, compared to their behaviour when they are exposed to an optimum hardening condition. The microstructure evolution has been studied with the non-destructive impedance spectroscopy technique, which has never been used for detecting the effects of sulphate attack when slag and fly ash cements are used. Its results have been contrasted with mercury intrusion porosimetry and “Wenner” resistivity ones. The 28-day compressive strength of grouts has been also determined. The results of microstructure characterization techniques are in agreement, although impedance spectroscopy is the most sensitive for following the changes in the porous network of grouts. The results showed that micropiles made using fly ash and slag cements could have a good performance in contact with aggressive sodium sulphate media, even better than OPC ones.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Microstructure and durability of fly ash cement grouts for micropiles

  • Pastor Navarro, José Luis
  • Ortega, José Marcos
  • Flor, María
  • López García, María Pilar
  • Sánchez, Isidro
  • Climent, Miguel-Ángel
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Pastor Navarro, José Luis|||/items/d54670cf-e108-40a1-9466-1cd07a1e614c
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
This paper presents a study on the possibility of using fly ash cement as grouts for micropiles. This type of special geotechnical work is commonly used for many applications. Generally, micropiles grouts are prepared using Portland cement, although the standards do not restrict the cement type to use, as long as they achieve a strength requirement. In this research, fly ash cement grouts made with w:c ratios 0.40, 0.45, 0.50 and 0.55 were studied from 2 up to 90 days of age. Their microstructure was characterized using the non-destructive impedance spectroscopy technique, electrical resistivity, and mercury intrusion porosimetry. Their durability properties have been studied by determining the water penetration under pressure, and the chloride diffusion coefficient. The compressive strength was also measured and determined, and a maximum water:cement ratio, different for each cement type was obtained. All the results were compared to those obtained for Portland cement grouts. The results obtained confirm that the performance of micropiles made using fly ash cement grouts is adequate, and as it is well know the cements with mineral admixtures provide environmental benefits, so the use of cement including fly ash will contribute to the sustainability, with similar properties to those given by OPC.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Influence of using slag cement on the microstructure and durability related properties of cement grouts for micropiles

  • Ortega, José Marcos
  • Albaladejo Ruiz, Arturo
  • Pastor Navarro, José Luis
  • Sánchez, Isidro
  • Climent, Miguel-Ángel
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Pastor Navarro, José Luis|||/items/d54670cf-e108-40a1-9466-1cd07a1e614c
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
Today, the use of micropiles for different applications has become very common. In Spain, the cement grouts for micropiles are prepared using ordinary Portland cement and w:c ratio 0.5, although the micropiles standards do not restrict the cement type to use, provided that it reaches a certain compressive strength. In this study, the influence of using slag cement on the microstructure and durability related properties of cement grouts for micropiles have been studied until 90 hardening days, compared to an ordinary Portland cement. Finally, slag cement grouts showed good service properties, better than ordinary Portland cement ones.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Non-Destructive Study of the Microstructural Effects of Sodium and Magnesium Sulphate Attack on Mortars Containing Silica Fume Using Impedance Spectroscopy

  • Williams, Mark
  • Ortega, José Marcos
  • Sánchez, Isidro
  • Cabeza, Marta
  • Climent, Miguel-Ángel
  • Climent, Miguel-Ángel|||/items/e85cc0b1-85b5-45a7-8949-fa16d269271f
  • Ortega, José Marcos|||/items/aaf3a7fd-4fce-4b2c-bf1c-d048bc7009b5
  • Sánchez, Isidro|||/items/0ce3f150-4e48-4f0a-9d0b-1f1b2025701c
The microstructural effects of exposure to a 15% magnesium sulphate, 15% sodium sulphate, and mixed solutions were observed in mortars with and without silica fume, using the non-destructive impedance spectroscopy technique. The non-destructive “Wenner” resistivity test and the classical mercury intrusion porosimetry were used as contrast techniques. The compressive strength of the mortars was also studied. In view of the results obtained, impedance spectroscopy was the most sensitive technique for detecting changes in the porous network of the studied mortars. The addition of silica fume results in a more refined microstructure and a higher compressive strength in mortars exposed to aggressive sulphate solutions.