Pasar al contenido principal

HORMIGONES SOSTENIBLES AUTOCOMPACTANTES DE ALTAS PRESTACIONES MEDIANTE EL USO DE CEMENTOS DE BAJO CONTENIDO EN CLINKER Y AGENTES DE CURADO INTERNO Y AUTSELLADO.

BIA2017-85657-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDADE DA CORUÑA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 21
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Wood ash versus expanded clay aggregate as internal curing water reservoirs in high performance concrete

  • Rodríguez-Álvaro, Roberto
  • González-Fonteboa, Belén
  • Seara-Paz, Sindy
  • Tenza-Abril, Antonio José
  • Tenza-Abril, Antonio José|||/items/07e0951f-fcaa-4f60-8f86-1d0ce5ca3f30
  • Rodríguez-Álvaro, Roberto|||/items/c9d764e5-06dd-4a73-bb87-9cebf6fb072b
The performances of expanded clay aggregate and wood ash as internal curing water reservoirs were studied in the mortar phase of a hypothetical high performance concrete with a low water-to-binder ratio. The two materials substituted the 15 and 30% of the sand volume. Two different binders, Portland cement and high-volume fly ash blended cement, were used. The compressive strength and the volume stability of the mortars in sealed and air-drying conditions were studied. Furthermore, the desorption capacity of the internal curing water reservoirs and the internal humidity inside the mortars during the first days after casting were analysed. The results shown that the reduction in the self-desiccation shrinkage was higher when the expanded clay aggregate was used, even in air-drying curing conditions, due to its higher desorption capacity in low-relative-humidity environments in comparison to that of the wood ash. However, wood ash had a stronger beneficial effect on early age autogenous shrinkage without significantly increasing the drying shrinkage. The two alternative aggregates influenced the strength moderately. Considering the technical, economic, and environmental implications of using the two lightweight aggregates, wood ash is recommended.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Mussel shells: A canning industry by-product converted into a bio-based insulation material

  • Martínez-García, Carolina
  • González-Fonteboa, Belén
  • Carro-López, Diego
  • Pérez Ordóñez, Juan Luis
[Abstract:] The canning industry in Galicia produces 25 thousand tonnes of mussel by-product (i.e. unconsumed shells) per year, having a significant environmental impact. Mussel shell becomes suitable for different uses after undergoing heat treatment such as poultry feed or bedding, etc. However, other end uses for this by-product must still be explored. Building insulation material (for instance expanded polystyrene, extruded polystyrene, polyurethane, etc.) has a significant harmful effect on the environment, which is especially seen when analysing its entire life cycle (use of large amounts of energy and water for production, difficulty recycling or reusing waste in the event of demolition or refurbishment, etc.). The aim of this research is to prove the feasibility of using mussel shell as a building solution. Mussel shell has been found to have thermal and acoustic characteristics suitable for using it as building insulation material. Mussel shell confined inside an enclosed space (e.g. a wooden box) has a thermal conductivity similar to that of a light conifer wood, so it can be considered a material with low thermal conductivity. Furthermore, several acoustic studies indicate that a section of confined mussel shell displays a behaviour similar to that of commercialised insulation material. The embodied energy of mussel shell as a loose-fill material is similar to that of other bio-based insulation materials. The main goal of this paper is to demonstrate that it is possible to design mussel shells building solutions, that actively participate in environmentally responsive architecture., This work has been carried out within the framework of the following projects: “Assessment of Galician bivalve shell in the construction sector”; Code 00064742/ITC-20133094, funded by CDTI under the FEDER-Innterconecta Program, and co-financed with European Union ERDF funds and “Sustainable High Performance Self Compacting Concrete using low clinker cement and internal curing and self healing agents”; Code BIA2017-85657-R funded by MINECO., Centro para el Desarrollo Tecnológico y la Innovación; 00064742/ITC-20133094
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Internally cured high performance concrete with magnesium based expansive agent using coal bottom ash particles as water reservoirs

  • Rodríguez-Álvaro, Roberto
  • González-Fonteboa, Belén
  • Seara Paz, Sindy
  • Hossain, Khandaker
[Abstract:] Shrinkage is one of the main concerns related to high performance concrete (HPC) durability. Its high density paste, consequence of a low water to binder ratio, can be unprofitable if cracks appear due to excessive tension when volume changes are restrained. Therefore, volume stability is a priority. In this work, three different strategies have been studied with that purpose: integration of fly ash as a low reactive supplementary cementitious material, internal curing via coal bottom ash particles as water reservoirs and the use of an expansive agent based on magnesium oxide (MEA). Many research works address the three shrinkage reduction strategies individually. However, studies regarding their simultaneous use are not prevalent so this work proposes its combined application. Results indicate that internal curing and MEA have a synergistic effect in HPC. Internal curing enhances MEA expansion due to the lack of water in this kind of concrete, contributing to autogenous shrinkage compensation. When concrete is affected by air-drying conditions, the use of MEA, internal curing, or both together make shrinkage to increase. MEA effectively expands in wet cured HPC although internal curing is not effective in this condition due to the absence of self-desiccation and limited porous aggregate water desorption. Taking into account the effects of each shrinkage reduction strategy and curing condition, it has been concluded that the use of fly ash as supplementary cementitious material, internal curing and MEA is recommended together with prevention of water evaporation from HPC surface., This work has been carried out within the framework of the HACCURACEM project (BIA2017-85657-R), funded by the Ministry of Economy, Industry and Competitiveness, State Program for Research, Development and Innovation aimed at the challenges of Society, within the framework of the State Plan for Scientific and Technical Research and Innovation 2013-2016, Call 2017. We also thank to Ryerson University (Toronto, Canada) in whose facilities the experimental part of this work was developed during a predoctoral stay funded by the government of Galicia, Xunta de Galicia. Finally, we highlight the collaboration of the companies Votorantim Cimentos and Grupo BASF, for the contribution of some of the materials used in this research.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Rheology, Durability, and Mechanical Performance of Sustainable Self-Compacting Concrete With Metakaolin and Limestone Filler

  • Rojo-López, Gemma
  • González-Fonteboa, Belén
  • Martínez-Abella, Fernando
  • González-Taboada, Iris
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract] This study analyzed the performance of self-compacting concrete with a paste composition that includes limestone filler and metakaolin replacing cement to design binary (75% cement and 25% limestone filler) and ternary binders (60% cement, 25% limestone filler and 15% metakaolin). Furthermore, to analyze the effect of the solid volume fraction (volume of sand and coarse aggregate) on concrete rheology, the concretes were designed using four volumes of paste (350 l, 400 l, 450 l and 500 l). Rheological tests were performed at three resting times to measure the viscosity and yield stress over time. The results indicated that the viscosity decreased by 43.3% when the cement was replaced by limestone filler and increased by 73.1% when the cement was replaced by 15% metakaolin while maintaining the limestone filler. These values were obtained as 27.6% and 62.2%, respectively, when the yield stress was analyzed. In addition, the hardened properties (mechanical behavior and durability) were studied by measuring the strengths at 28 days, as well as the electrical resistivity and ultrasonic pulse velocity over time. In this case, at 28 days the use of binary binder reduces the strength and resistivity (about 20%) and the employment of ternary binder reduces strength (15%) while increases the resistivity up to the double (when compared to the 100 C concrete). Moreover, to measure the efficiency of the concrete, a material index was designed that considers the fresh behavior, mechanical performance, durability, cost, and environmental impact. Self-compacting concretes with ternary binders provided the highest indices. The use of alternative materials, particularly metakaolin has been proven to be a good option to enhance concrete sustainable performance., The study is part of two projects entitled: “Robust self-compacting recycled concretes: rheology in fresh state and mechanical properties (Ref: BIA2014-58063-R)” and “Sustainable High Performance Self-Compacting Concrete using low clinker cement, and integral curing and self-healing agents (HACCURACEM) (BIA2017-85657-R)” funded by MINECO. Moreover, this work was also made possible by the financial support of a pre-doctoral grant of MINECO (FPI 2015- ref BES-2015-071919) and two grants for international pre-doctoral stays: (a) FPI 2015 and (b) IACOBUS program for “Galicia–North of Portugal Euroregion”
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Towards an in-situ evaluation methodology of thermal resistance of basement walls in buildings

  • Bienvenido Huertas, José David
  • Pérez Ordóñez, Juan Luis
  • Moyano, Juan
  • Seara Paz, Sindy
[Abstract]: One of the essential aspects in building energy analysis is determining correctly the thermal characteristics of envelopes. Characterizing envelope elements accurately allows energy consumption to be predicted and energy saving measures to be established. Basement walls are among those common envelope elements in buildings. The estimation of their thermal resistance is a challenge due to the difficulties and the lack of methodologies to know the wall stratigraphy. This study establishes a methodology to characterize the thermal resistance of this kind of walls. Such methodology consists in monitoring easily measurable variables (internal air temperature, external air temperature, ground temperature, internal surface temperature, and heat flux) which, together with the use of regression models, estimate thermal resistance. The methodology is validated in 2 phases: (i) in a calibrated hot-box adapted to elements in contact with the ground, and (ii) by analysing actual case studies. With the data obtained, various regression models are created based on time windows. The M5 Prime algorithm with a time window of 2 days of observation made accurate estimations in the case studies. An efficient methodology is therefore developed for estimating the thermal resistance in actual case studies. Also, the calibrated hot-box adapted could be used to analyse samples under controlled conditions in laboratory., This work was partially supported by the Spanish Ministry of Science, Innovation and Universities (Code 00064742/ITC-20133094), funded by CDTI (Centro para el Desarrollo Tecnológico e Industrial) under the FEDER-Innterconecta Program, and co-financed with European Union Regional Development Fund. Also, was partially supported by Spanish Ministry of Economy, Industry and Competitiveness (Code BIA 2017-85657-R). The authors would like to acknowledge Own Research Plan of the University of Seville for financing the mobility of David Bienvenido-Huertas and Juan Moyano at the University of A Coruña., Centro para el Desarrollo Tecnológico e Industrial; 00064742/ITC-20133094
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Effects of mussel shell aggregates on hygric behaviour of air lime mortar at different ages

  • Martínez-García, Carolina
  • González-Fonteboa, Belén
  • Carro-López, Diego
  • Martínez-Abella, Fernando
[Abstract:] Mussel shells, composed of calcium carbonate (>95%) and organic matter, are suitable alternatives to conventional sand in mortar. In addition, the use of lime instead of cement as a binder has also been considered for sustainable construction materials as well as in restorative applications. This study aims to contribute to the knowledge of air lime mortar through the analysis of the water transport properties of air lime mortar produced with mussel shell aggregates at different ages. Four mortar groups were obtained from the reference mortar by replacing limestone sand with mussel shell sand at substitution rates of 25%, 50%, and 75%. Water absorption, capillary uptake, weight variation, and drying from the fresh state up till one and two years were determined. The organic matter content and flaky seashell shape are responsible for the main differences observed between the mussel mortars and reference mortar. These two characteristics promote transport tortuosity paths and hydrophobic behaviour leading to reduced capillary uptake and increased drying resistance index. Furthermore, they enhance water retention, which increases the carbonation rate., This work has been carried out within the framework of the following projects: “Assessment of Galician bivalve shell in the construction sector”; Code 00064742/ITC-20133094, funded by CDTI under the FEDER-Innterconecta Program, and co-financed with European Union ERDF funds and “Sustainable High Performance Self Compacting Concrete using low clinker cement and internal curing and self healing agents”; Code BIA2017-85657-R funded by MINECO., Centro para el Desarrollo Tecnológico y la Innovación; 00064742/ITC-20133094
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Valorização de resíduos de biomassa e da extração de pedra natural no fabrico de betão autocompactável, Valorisation of biomass ash and granite powder in the production of self-compacting concrete

  • Rojo-López, Gemma
  • Nunes, Sandra
  • Martínez-Abella, Fernando
  • González-Fonteboa, Belén
[Resumo] O presente trabalho visa explorar a viabilidade da incorporação simultânea de cinzas da biomassa e de pó-de-pedra em betão autocompactável, ambos resíduos gerados por setores industriais instalados na Eurorregião Galiza-Norte de Portugal. Foi desenvolvido um programa experimental segundo um plano fatorial, ao nível da argamassa, como uma fase do estudo que antecede o estudo ao nível do betão. Para cada mistura do plano, foram analisadas diversas propriedades da argamassa, nomeadamente, para caraterizar a respetiva trabalhabilidade, resistência mecânica e durabilidade. Com este estudo demonstrou-se que o pó-de-pedra e a cinza da biomassa podem ser incorporados em conjunto para produzir BACs de elevada deformabilidade, sem risco de segregação. Simultaneamente, ao substituir uma parte do cimento por metacaulino foi possível melhorar significativamente as propriedades do BAC no estado endurecido (maior resistência à compressão, maior resistividade e menor porosidade acessível à àgua), enquanto se reduzem as emissões de CO2 pelo uso de menos cimento., [Abstract] The present work aims to explore the feasibility of incorporating biomass ash and granite powder, wastes generated by two industrial sectors operating in the Galicia-North of Portugal Euroregion, in self-compacting concrete. An experimental program was developed according to a factorial plan, at the mortar level, as a step before the study at the concrete level. For each mixture in the plan, several properties of the mortar were analysed, namely to characterise the workability, mechanical strength and durability. This study shows granite powder and biomass ash can be incorporated together to produce SCCs of high deformability, without risk of segregation. At the same time, by replacing a fraction of the cement with metakaolin, it was possible to significantly improve the properties of SCC in the hardened state (higher compressive strength, higher resistivity and lower porosity accessible to water), while reducing CO2 emissions due to lower cement content., Este trabalho foi financiado por: Unidade de Investigação UID/ECI/04708/2019 – CONSTRUCT - Instituto de I&D em Estruturas e Construções – financiada por fundos nacionais através da FCT/MCTES (PIDDAC). Este trabalho foi apoiado pelo programa IACOBUS - Programa de Cooperação Cultural, Científica e Pedagógica para Mobilidade Pré-doutoral, e pelos projetos BIA 2014-58063-R (HORREO) e BIA 2017-85657-R (HACCURACEM) del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, MINECO., Portugal. Instituto de I&D em Estruturas e Construções; UID/ECI/04708/2019
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Assessment of mussel shells building solutions: A real-scale application

  • Martínez-García, Carolina
  • González-Fonteboa, Belén
  • Carro-López, Diego
  • Pérez Ordóñez, Juan Luis
[Abstract:] The construction sector is a key generator of greenhouse emissions, so the use of alternative low-emission building materials is a growing tendency. This work describes and analyses an innovative sustainable building that includes mussel shells in all its constructive elements. This material is a by-product of the canning industry that is nowadays landfilled. Mussel shells were used as aggregate in the concrete strip footing (foundation) and in the exterior and interior coating mortars (walls), and as loose-fill material for the whole envelope insulation (floor, walls, and roof). The results from both the laboratory and the constructive process were useful to improve the solutions and to develop a building with low energy consumption. Finally, the energy demand of the building was assessed using the Passive House Planning Package (PHPP) software and the blower door test was carried out to measured air tightness. It can be concluded that mussel shell materials meet the requirements of Passive House standard for energy efficient buildings: simulation results showed a primary energy consumption of 86 kWh/(m2yr), that is a 28.3% lower than the value fixed by the standard., This work has been carried out within the framework of the following projects: “Assessment of Galician bivalve shell in the construction sector”; Code 00064742/ITC-20133094, funded by CDTI under the FEDER-Innterconecta Program (Consortium of Extraco SA, Galaicontrol SL & Serumano SL and Universidade da Coruña), and co-financed with European Union ERDF funds and “Sustainable High Performance Self Compacting Concrete using low clinker cement and internal curing and self healing agents”; Code BIA2017-85657-R funded by MINECO., Centro para el Desarrollo Tecnológico y la Innovación; 00064742/ITC-20133094
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Waste-Based Porous Materials as Water Reservoirs for the Internal Curing of Concrete. A Review

  • Rodríguez-Álvaro, Roberto
  • Seara Paz, Sindy
  • González-Fonteboa, Belén
  • Ferrándiz-Mas, Verónica
  • Paine, Kevin
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract] This review collates findings from more than 100 scientific publications regarding the performance of several waste-based porous materials (WASPORs) as water reservoirs for the internal curing of concrete. Results obtained by using recycled concrete aggregates, crushed ceramics, coal bottom ash, artificial waste-based aggregates, different powder materials and porous fibres were included. The influence of these WASPORs on the consistence, hydration, setting, microstructure, density, strength, modulus of elasticity, autogenous deformation, drying shrinkage and durability properties of concrete were analysed. General recommendations for suitable characterization of WASPOR and mix design are also given. The differences in water absorption capacity between the different porous materials studied have been used for explaining several of the observed phenomena. A moderate water absorption capacity together with a quick water desorption capacity were found to be among the key factors that define the internal curing efficiency of the proposed WASPORs., This work has been carried out within the framework of the HACCURACEM project (BIA2017-85657-R), funded by the Ministry of Economy, Industry and Competitiveness, State Program for Research, Development and Innovation aimed at the challenges of Society, within the framework of the State Plan for Scientific and Technical Research and Innovation 2013-2016, Call 2017. We also thank Universidade da Coruña for the grants (Axudas Investigación UDC 2017) that facilitated the stay at the University of Bath (UK)
RUC. Repositorio da Universidade da Coruña
Publicación Tesis doctoral (DoctoralThesis)

Internal curing of high-performance concrete via waste-based porous materials, Curado interno de formigón de altas prestacións mediante materiais porosos en base a residuos

  • Rodríguez-Álvaro, Roberto
[Abstract] This work presents the use of different waste based porous materials as internal curing water reservoirs in high performance concrete, which is strongly aligned with the objective of promoting circularity in the construction industry. Internal curing was studied in combination with other shrinkage reduction strategies such as the use of coal fly ash as a low reactive supplementary cementitious material, and the use of a magnesium based expansive agent. The following waste based porous materials were used: ceramic recycled aggregates, mixed recycled aggregates, coal bottom ash and wood bottom ash. A conventional lightweight expanded clay aggregate was also used. The following properties were studied on the proposed mixtures: workability, hydration, setting, air content, density, porosity, strength, volume stability and durability. Internal curing via waste based porous materials can effectively mitigate autogenous shrinkage without significantly jeopardizing other properties. However, the alternative materials should be carefully characterized and the mix proportions should be studied in depth. Furthermore, it was concluded that external curing is needed even if internal curing is used, and synergistic effects were detected between the proposed shrinkage reduction strategies. Therefore, this work presents a feasible solution for a more durable and sustainable construction., [Resumen] Este trabajo propone el uso de diferentes materiales porosos procedentes de residuos como reservorios de agua de curado interno en el hormigón de altas prestaciones, lo cual está fuertemente alineado con el objetivo de promover la circularidad en la industria de la construcción. El curado interno se estudió en combinación con otras estrategias de reducción de la retracción como el uso de ceniza volante de carbón como material cementante suplementario de baja reactividad y el uso de un agente expansivo basado en magnesio. Como materiales porosos procedentes de residuos, se utilizaron los siguientes: áridos reciclados cerámicos, áridos reciclados mixtos, ceniza de fondo de carbón y ceniza de fondo de madera. También se utilizó un árido convencional de arcilla expandida. Se estudiaron las siguientes propiedades sobre las mezclas propuestas: trabajabilidad, hidratación, fraguado, contenido de aire, densidad, porosidad, resistencia, estabilidad de volumen y durabilidad. El curado interno a través de materiales porosos procedentes de residuos puede mitigar la retracción autógena sin perjudicar significativamente otras propiedades. Sin embargo, los materiales alternativos usados deben ser caracterizados cuidadosamente y las dosificaciones estudiadas en profundidad. Además, se concluyó que el curado externo es necesario, aunque se use el curado interno, y se detectaron efectos sinérgicos entre las distintas estrategias de reducción de la retracción propuestas. Por lo tanto este trabajo presenta una solución viable para una construcción más durable y sostenible., [Resumo] Este traballo propón o uso de diferentes materiais porosos procedentes de residuos como reservorios de auga de curado interno no formigón de altas prestación, o cal está fortemente aliñado co obxectivo de promover a circularidade na industria da construción. O curado interno estudiouse en combinación con outras estratexias de redución da retracción coma o uso da cinza voante de carbón como material cementante suplementario de baixa reactividade e o uso dun axente expansivo baseado en magnesio. Como materiais porosos procedentes de residuos, utilizáronse os seguintes: áridos reciclados cerámicos, áridos reciclados mixtos, cinza de fondo de carbón e cinza de fondo de madeira. Tamén se empregou un árido convencional de arxila expandida. Estudáronse as seguintes propiedades sobre as mesturas propostas: traballabilidade, hidratación, fraguado, contido de aire, porosidade, resistencia, estabilidade de volume e durabilidade. O curado interno a través de materiais porosos procedentes de residuos pode mitigar a retracción autóxena sen prexudicar significativamente outras propiedades. Non obstante, os materiais alternativos usados deben ser caracterizados coidadosamente e as dosificacións estudadas en profundidade. Ademais, concluíuse que o curado externo é necesario aínda que se use o curado interno, e detectáronse efectos sinérxicos entre as distintas estratexias de redución da retracción propostas. Polo tanto, este traballo presenta unha solución viable para unha construción máis durable e sostible.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Quaternary blends of portland cement, metakaolin, biomass ash and granite powder for production of self-compacting concrete

  • Rojo-López, Gemma
  • Nunes, Sandra
  • González-Fonteboa, Belén
  • Martínez-Abella, Fernando
[Abstract:] Given the rising societal pressure towards sustainable waste management and resource efficiency, in a more circular economy, an increased use and diversification of supplementary cementitious materials (SCM) will be necessary to achieve the CO2 mitigation goals. The current study addresses the development of self-compacting concrete, replacing part of the cement (the primary source of CO2 emissions) by metakaolin and wastes derived from two industrial sectors operating in the “Galicia–North of Portugal Euroregion”: wood manufacturing and natural stone quarrying. A study was carried out at the mortar level to investigate the effect of the mix design variables on several engineering properties of the self-compacting concrete. Statistically designed experiments reveal that an increase in water/powder volume ratio has a dominant effect on the fresh state properties, whereas the water/cement weight ratio has a dominant effect on the hardened state properties. A like-for-like comparison of the proposed quaternary blends and previously studied binary/ternary blends indicates that these mixtures exhibit improved self-compacting ability, greater compressive strength, and can offer interesting opportunities to reduce the unit cost and environmental impact of self-compacting concrete per m3. Four different mortar mixtures were optimised to achieve excellent self-compacting ability yet with distinct compressive strength levels at 28 days (65, 70, 75, and 80 MPa). A single measure of the material efficiency is proposed herein to reflect the engineering properties improvement (workability, compressive strength, and durability) over its economic (unit cost) and environmental impact., This work was financially supported by: Base Funding - UIDB/04708/2020 and Programmatic Funding - UIDP/04708/2020 of the CONSTRUCT - Instituto de I&D em Estruturas e Construções - funded by national funds through the FCT / MCTES (PIDDAC); by the INBRAIL project - POCI-01-0247-FEDER-033990 funded by FEDER funds through COMPETE2020 - Programa Operacional Competitividade e Internacionalização (POCI) and Programa Operacional da Região de Lisboa within Sistema de Incentivos à Investigação e Desenvolvimento (SI IDT) from Portugal (2020) “Projetos I&DT Empresas em Co promoção”. The study is part of two projects entitled: “Robust self-compacting recycled concretes: rheology in fresh state and mechanical properties (Ref: BIA2014-58063-R)” and “Sustainable High Performance Self-Compacting Concrete using low clinker cement, and integral curing and self-healing agents (HACCURACEM) (BIA2017-85657-R)” funded by MINECO. Moreover, this work was also made possible by the financial support of a pre-doctoral grant of MINECO (FPI 2015) and two grants for international pre-doctoral stays: (a) FPI 2015 and (b) IACOBUS program for “Galicia–North of Portugal Euroregion”., Portugal. Instituto de I&D em Estruturas e Construções; UIDB/04708/2020, Portugal. Instituto de I&D em Estruturas e Construções; UIDP/04708/2020, Portugal. Programa Operacional Competitividade e Internacionalização; POCI-01-0247-FEDER-033990
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Use of granular coal combustion products as aggregates in structural concrete: Effects on properties and recommendations regarding mix design

  • Rodríguez-Álvaro, Roberto
  • Seara Paz, Sindy
  • González-Fonteboa, Belén
  • Martínez-Abella, Fernando
[Abstract:] This review collates the results obtained in more than 100 scientific publications regarding the performance of concrete with granular coal combustion products (GCCP, commonly referred to as coal bottom ash in literature) as a partial substitute for conventional aggregate. The effects of this by-product on the workability, density and mechanical and durability related properties were analysed. Some conclusions and recommendations are provided to facilitate future research. These recommendations include conducting careful assessments of the specific gravity and water absorption properties of GCCP, replacing conventional aggregate by volume, and compensating the water absorption of GCCP. The use of GCCP as an internal curing water reservoir is proposed as the most promising advanced application., This work has been carried out within the framework of the following projects: -HACCURACEM project (BIA2017-85657-R), funded by the Ministry of Economy, Industry and Competitiveness, State Program for Research, Development and Innovation aimed at the challenges of Society, within the framework of the State Plan for Scientific and Technical Research and Innovation 2013-2016, Call 2017. -Valorisation of coal ashes from thermal power plant through the development of sustainable materials and products for the eco-construction in the building and civil engineering field (Cenicienta), funded by the Innovation Galician Agency, Galician Government (Xunta de Galicia), FEDER 2014-2020, Call 2016.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Carbonation evolution of lime putty coatings with mussel shell aggregate

  • Martínez-García, Carolina
  • González-Fonteboa, Belén
  • Carro-López, Diego
  • Martínez-Abella, Fernando
[Abstract:] The carbonation process is studied from young ages up to 2 years in mortars with fine mussel shell aggregate. Mussel shell aggregate affects lime mortars due to its shape (angular and flaky) and texture (smooth), and also its microstructure consisting of 2% organic matter in the form of protein and polysaccharides (chitin). Its effect is analysed in pore structure, microstructure by SEM, carbonation by phenolphthalein, and mechanical strength by means of compressive strength and ultrasounds. Conclusions show that the use of mussel shell aggregate delays carbonation at young ages (28 days) while increasing the total carbonated area at longer ages (1 and 2 years). These two different trends can be seen in all of the properties analysed., This work has been carried out within the framework of the following projects: “Assessment of Galician bivalve shell in the construction sector”; Code 00064742/ITC-20133094, funded by CDTI under the FEDER-Innterconecta Program, and co-financed with European Union ERDF funds and “Sustainable High Performance Self Compacting Concrete using low clinker cement and internal curing and self healing agents”; Code Bia2017-85657-R funded by MINECO., Centro para el Desarrollo Tecnológico y la Innovación; 00064742/ITC-20133094
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Wood Ash Versus Expanded Clay Aggregate as Internal Curing Water Reservoirs in High Performance Concrete

  • Rodríguez-Álvaro, Roberto
  • González-Fonteboa, Belén
  • Seara Paz, Sindy
  • Tenza-Abril, Antonio José
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract] The performances of expanded clay aggregate and wood ash as internal curing water reservoirs were studied in the mortar phase of a hypothetical high performance concrete with a low water-to-binder ratio. The two materials substituted the 15 and 30% of the sand volume. Two different binders, Portland cement and high-volume fly ash blended cement, were used. The compressive strength and the volume stability of the mortars in sealed and air-drying conditions were studied. Furthermore, the desorption capacity of the internal curing water reservoirs and the internal humidity inside the mortars during the first days after casting were analysed. The results shown that the reduction in the self-desiccation shrinkage was higher when the expanded clay aggregate was used, even in air-drying curing conditions, due to its higher desorption capacity in low-relative-humidity environments in comparison to that of the wood ash. However, wood ash had a stronger beneficial effect on early age autogenous shrinkage without significantly increasing the drying shrinkage. The two alternative aggregates influenced the strength moderately. Considering the technical, economic, and environmental implications of using the two lightweight aggregates, wood ash is recommended., Funding for open access charge: Universidade da Coruña/CISUG. This work has been carried out within the framework of the HACCURACEM project (BIA2017-85657-R), funded by the Ministry of Economy, Industry and Competitiveness, State Program for Research, Development and Innovation aimed at the challenges of Society, within the framework of the State Plan for Scientific and Technical Research and Innovation 2013–2016, Call 2017. We also thank the Xunta de Galicia (Spain) for the financial support through its pre-doctoral contracts program. Finally, we highlight the collaboration of the companies Votorantim Cimentos and Grupo BASF, for the contribution of some of the materials used in this research
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Study of Different Granular By-Products as Internal Curing Water Reservoirs in Concrete

  • Rodríguez-Álvaro, Roberto
  • Seara Paz, Sindy
  • González-Fonteboa, Belén
  • Etxeberria, Miren
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract] The use of three different waste-based materials, i.e. ceramic recycled aggregate (CRA), mixed recycled aggregate (MRA), and coal bottom ash (CBA), as internal curing water reservoirs was investigated. Their effects as fine aggregates in the mortar phase of a hypothetical concrete with a low water-to-binder ratio were studied. The used binders were ordinary Portland cement and high-volume fly-ash-blended cement. The addition of MRA and CBA significantly decreased the autogenous shrinkage, whereas their negative effects on drying shrinkage and the compressive strength were minimal. However, the CRA had the worst effect on autogenous shrinkage but increased the strength of the specimens., This work has been carried out within the framework of the HACCURACEM project (BIA2017-85657-R), funded by the Ministry of Economy, Industry and Competitiveness, State Program for Research, Development and Innovation aimed at the challenges of Society, within the framework of the State Plan for Scientific and Technical Research and Innovation 2013–2016, Call 2017. We also thank the Xunta de Galicia (Spain) for the financial support through its pre-doctoral contracts program. Finally, we highlight the collaboration of the companies Votorantim Cimentos and Grupo BASF, for the contribution of some of the materials used in this research
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Masonry Mortars, Precast Concrete and Masonry Units Using Coal Bottom Ash as a Partial Replacement for Conventional Aggregates

  • Rodríguez-Álvaro, Roberto
  • González-Fonteboa, Belén
  • Seara Paz, Sindy
  • Rey-Bouzón, E.
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract] Granular coal combustion products are problematic waste materials whose use as aggregates in concrete has been extensively studied. However, its integration into other non-structural materials and elements has not been so widely documented. Masonry mortars, precast concrete and masonry units with different ratios of coal bottom ash replacing conventional aggregates have been studied. With the incorporation of coal bottom ash in the mortars, the workability, density and strength decrease whereas the porosity, the weight loss and the drying shrinkage increase. However, low replacement ratios have slight effects. The use of coal bottom ash as an internal curing water reservoir is proposed as the most promising future line of research., This work has been carried out within the framework of the following projects: HACCURACEM project (BIA2017-85657-R), funded by the Ministry of Economy, Industry and Competitiveness, State Program for Research, Development and Innovation aimed at the challenges of Society, within the framework of the State Plan for Scientific and Technical Research and Innovation 2013-2016, Call 2017. Valorisation of coal ashes from thermal power plant through the development of sustainable materials and products for the eco-construction in the building and civil engineering field (Cenicienta), funded by the Innovation Galician Agency, Galician Government (Xunta de Galicia), FEDER 2014-2020, Call 2016
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Deformation Recovery of Reinforced Concrete Beams Made With Recycled Coarse Aggregates

  • Seara Paz, Sindy
  • González-Fonteboa, Belén
  • Martínez-Abella, Fernando
  • Eiras López, Javier
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract] The purpose of this research is to analyse the long-term deformations of reinforced concrete beams made of recycled coarse aggregates (RCA), using four different replacement ratios, 0%, 20%, 50% and 100%. For said purpose, three different loading stages were carried out: firstly, loading and sustained load for 1300 days, secondly, unloading and recovery where the deformations were registered over a one year period, and lastly, testing the concrete beams up to failure in order to analyse the effect of recycled aggregates on pre-cracked concrete members. The results led to the analysis of deformations under sustained load, as well as those produced after removing the load and the performance of pre-cracked members, while identifying the effect of recycled coarse aggregates on concrete performance in terms of plastic deformation, recoverability and concrete stiffness, and also on structural design., The study has been funded by: “CLEAM: Clean, efficient and nice construction along its life cycle” funded by the Centre for the Technology and Industrial Development (CDTI) and led by the Group of Economical Interest CLEAM-CENIT, AIE comprising by the country’s largest construction companies (Acciona, Dragados, Ferrovial, FCC, Isolux Corsán, OHL and Sacyr) and some PYME (Informática 68, Quilosa and Martínez Segovia y asociados). “HACCURACEM: HACCURACEM project (BIA2017-85657-R), funded by the Ministry of Economy, Industry and Competitiveness, State Program for Research, Development and Innovation aimed at the challenges of Society, within the framework of the State Plan for Scientific and Technical Research and Innovation 2013-2016, Call 2017
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Effect of supplementary cementitious material and fine recycled aggregates on shrinkage properties of self-compacting microconcrete

  • Etxeberria Larrañaga, Miren|||0000-0003-2208-6207
  • Bommana Tippareddygari, Purandhar Reddy
An increase in the population has led to the progressive construction of infrastructures and buildings. This causes severe environmental problems, firstly high emissions of CO2 are caused in cement production; secondly, a high volume of construction and demolition waste is landfilled and thirdly, it is necessary to look for new, no natural resources for the production of construction materials. The objective of this work is to analyse the influence of fine recycled aggregates and high volumes of fly ash in the properties of high-performance self-compacting (SC) microconcrete. The experimental work presented in this paper was carried out in two phases. In phase 1, SC- microconcrete were produced with 100% of Portland cement, and natural sand was replaced by both mixed and ceramics recycled aggregates in 30% and 50%. In phase 2, SC- microconcretes were produced with the replacement of 50% of Portland cement by fly ash, and natural sand was replaced by both mixed and ceramics recycled aggregates in 30% and 50%. In each phase, the drying and autogenous shrinkage of all mortars was measured via their storage in a climate chamber after 24 hours of casting and the determining of properties during 90 days. In order to assess the influence of the shrinkage effect on the mechanical properties, the prismatic samples were also stored in a climatic chamber, and the compressive strength at several ages was determined in all of the SC mixtures. The results showed that the microconcretes produced employing mixed and ceramic fine aggregates achieved higher compressive strength and lower autogenous shrinkage. Although the C-N achieved the lowest drying shrinkage, the mixtures with 30% of CRA and MRA were found to have similar values. The employment of the CRA aggregates improved the drying shrinkage and compressive strength of the C-FA-N mixture.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Study of different granular by-products as internal curing water reservoirs in concrete

  • Rodríguez Álvaro, Roberto
  • Seara Paz, Gumersinda
  • González Fonteboa, Belen
  • Etxeberria Larrañaga, Miren|||0000-0003-2208-6207
The use of three different waste-based materials, i.e. ceramic recycled aggregate (CRA), mixed recycled aggregate (MRA), and coal bottom ash (CBA), as internal curing water reservoirs was investigated. Their effects as fine aggregates in the mortar phase of a hypothetical concrete with a low water-to-binder ratio were studied. The used binders were ordinary Portland cement and high-volume fly-ash-blended cement. The addition of MRA and CBA significantly decreased the autogenous shrinkage, whereas their negative effects on drying shrinkage and the compressive strength were minimal. However, the CRA had the worst effect on autogenous shrinkage but increased the strength of the specimens., This work has been carried out within the framework of the HACCURACEM project (BIA2017-85657-R), funded by the Ministry of Economy, Industry and Competitiveness, State Program for Research, Development and Innovation aimed at the challenges of Society, within the framework of the State Plan for Scientific and Technical Research and Innovation 2013–2016, Call 2017. We also thank the Xunta de Galicia (Spain) for the financial support through its pre-doctoral contracts program. Finally, we highlight the collaboration of the companies Votorantim Cimentos and Grupo BASF, for the contribution of some of the materials used in this research., Peer Reviewed, Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Effect of supplementary cementitious material and fine recycled aggregates on shrinkage properties of self-compacting microconcrete

  • Etxeberria Larrañaga, Miren
  • Bommana Tippareddygari, Purandhar Reddy
An increase in the population has led to the progressive construction of infrastructures and buildings. This causes severe environmental problems, firstly high emissions of CO2 are caused in cement production; secondly, a high volume of construction and demolition waste is landfilled and thirdly, it is necessary to look for new, no natural resources for the production of construction materials. The objective of this work is to analyse the influence of fine recycled aggregates and high volumes of fly ash in the properties of high-performance self-compacting (SC) microconcrete. The experimental work presented in this paper was carried out in two phases. In phase 1, SC- microconcrete were produced with 100% of Portland cement, and natural sand was replaced by both mixed and ceramics recycled aggregates in 30% and 50%. In phase 2, SC- microconcretes were produced with the replacement of 50% of Portland cement by fly ash, and natural sand was replaced by both mixed and ceramics recycled aggregates in 30% and 50%. In each phase, the drying and autogenous shrinkage of all mortars was measured via their storage in a climate chamber after 24 hours of casting and the determining of properties during 90 days. In order to assess the influence of the shrinkage effect on the mechanical properties, the prismatic samples were also stored in a climatic chamber, and the compressive strength at several ages was determined in all of the SC mixtures. The results showed that the microconcretes produced employing mixed and ceramic fine aggregates achieved higher compressive strength and lower autogenous shrinkage. Although the C-N achieved the lowest drying shrinkage, the mixtures with 30% of CRA and MRA were found to have similar values. The employment of the CRA aggregates improved the drying shrinkage and compressive strength of the C-FA-N mixture., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Study of different granular by-products as internal curing water reservoirs in concrete

  • Rodríguez Álvaro, Roberto
  • Seara Paz, Gumersinda
  • González Fonteboa, Belen
  • Etxeberria Larrañaga, Miren
The use of three different waste-based materials, i.e. ceramic recycled aggregate (CRA), mixed recycled aggregate (MRA), and coal bottom ash (CBA), as internal curing water reservoirs was investigated. Their effects as fine aggregates in the mortar phase of a hypothetical concrete with a low water-to-binder ratio were studied. The used binders were ordinary Portland cement and high-volume fly-ash-blended cement. The addition of MRA and CBA significantly decreased the autogenous shrinkage, whereas their negative effects on drying shrinkage and the compressive strength were minimal. However, the CRA had the worst effect on autogenous shrinkage but increased the strength of the specimens., This work has been carried out within the framework of the HACCURACEM project (BIA2017-85657-R), funded by the Ministry of Economy, Industry and Competitiveness, State Program for Research, Development and Innovation aimed at the challenges of Society, within the framework of the State Plan for Scientific and Technical Research and Innovation 2013–2016, Call 2017. We also thank the Xunta de Galicia (Spain) for the financial support through its pre-doctoral contracts program. Finally, we highlight the collaboration of the companies Votorantim Cimentos and Grupo BASF, for the contribution of some of the materials used in this research., Peer Reviewed, Objectius de Desenvolupament Sostenible::12 - Producció i Consum Responsables, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura, Postprint (published version)