Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Effect of aggregate content and fibre type on the rheological behaviour and structural build-up of fibre reinforced self-compacting concrete using two binder compositions

  • Rojo-López, Gemma
  • González-Fonteboa, Belén
  • Martínez-Abella, Fernando
  • Seara Paz, Sindy
[Abstract:] Many parameters influence the fresh behaviour of fibre reinforced self-compacting concrete (FRSCC), such as length, aspect ratio, fibre content, solid volume fraction, and particle interaction. Most studies did not analyse rheological behaviour (just workability) and they are focused on paste or mortar. However, the analysis at the concrete level is also required to confirm the behaviour when the coarse aggregates and fibres are employed. This kind of analysis is scarce in the literature. Hence, this work aims to increase the knowledge about the effect of aggregate content and fibre type on FRSCC. To do so, the behaviour of self-compacting mixes with three different aggregate contents (550, 500, and 650 l/m3), two cementitious systems (100 % cement, and 60 % cement, 25 % limestone filler and 15 % metakaolin), and three different types of rigid fibres (two metallic and one polypropylene) were analysed. To characterise the concrete rheological performance, the stress growth test (SGT) was selected to avoid any fibre orientation. SGT was repeated twice under undisturbed and disturbed conditions to assess the structural build-up of the concrete. The results indicate that there is a critical value of the relative packing fraction that, once overcome, severely affects the fresh behaviour of FRSSC. This critical value can be calculated as the ratio between random loose packing fraction and dense packing fraction. It can be used to design a FRSCC mix guaranteeing that the fresh state remains in a suitable range where the hydrodynamic interactions dominate the behaviour and therefore, changes in the mix composition will not sharply modify the rheological performance of the concrete., This research was funded by the Spanish Ministerio de Ciencia e innovación - Agencia Estatal de investigación through three projects entitled: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)- PID2020–115433RB-I00”, “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)- PDC2021–121660-I00” and "Exploiting the synergic effects between 3D printing and self-healing technologies to design sustainable and durable concrete (3DHealConcrete) - TED2021–129757B-I00"
RUC. Repositorio da Universidade da Coruña
Publicación Contribución de congreso (ConferenceOutput)

De la realidad a lo digital mediante LiDAR

  • Carvallo García, Sara
  • Garrido Iglesias, André
  • Cañizares Sánchez, Alicia
  • Romero Fernández, José
  • Pérez Ordóñez, Juan Luis
[Resumen]: En este artículo se muestra el flujo de trabajo necesario para realizar el modelo construido de un edificio, también denominado modelo “As-built”, empleando técnicas de levantamiento 3D mediante escaneo LiDAR. El artículo muestra todos los pasos necesarios, desde la planificación en la toma de información hasta la generación del gemelo digital. Cabe resaltar que se realiza un estudio pormenorizado sobre la captura (se emplearán distintos escáneres) y el procesamiento de la nube de puntos con el objetivo de trabajar de forma eficiente según la información que sea necesaria para el uso concreto del modelo (mantenimiento, mediciones, gestión de espacios, análisis estructural, auditoria...) y su materialización en una herramienta de modelado. Para llevar a cabo este trabajo, se emplea un caso práctico de levantamiento de una obra ya realizada (4314m2 repartidos en 3 plantas más una planta baja y un sótano) mediante la captura de una nube de puntos. Se explicará el proceso de toma de datos, los factores a tener en cuenta a la hora de elegir el equipo de escaneo idóneo, el modo de empleo de cada equipo y los resultados obtenidos. Por último, se expondrán las diferentes aplicaciones prácticas que aporta el uso de esta tecnología y sus posibles desarrollos futuros., [Abstract]: This paper shows the workflow required to make the As-built model of a building, using 3D survey techniques by LiDAR scanning. The paper shows all the necessary steps, from panning in the data acquisition to the generation of the digital twin. It is highlighted that a detailed study is carried out on the capture (different scanners will be used) and processing of the point cloud to work efficiently according to the information that is necessary for the specific use of the model (facility management, measurements, space management, structural analysis, auditing...) and its development into a modeling tool. To carry out this work, a practical case of a survey of an already completed construction site (4314m2 spread over three floors and one ground floor and a basement) is used by capturing a point cloud. The data acquisition method, the factors to be considered when choosing the appropriate scanning equipment, the use of each equipment, and the results obtained will be explained. Finally, the different practical applications of this technology and possible future developments will be presented., Este trabajo contó con el apoyo parcial del Ministerio de Ciencia e Innovación, NextGeneration (Ref: PDC2021-121660-I00 PREHEALING).
RUC. Repositorio da Universidade da Coruña
Publicación Tesis doctoral (DoctoralThesis)

Research and New Smart Techniques on the Characterisation of New Self-compacting Concrete with Industrial Wastes and Fibres to Increase its Sustainability and Service Life, Investigación e novas técnicas intelixentes na caracterización de novos formigóns autocompactantes con residuos industriais e fibras para aumentar a súa sustentabilidade e vida útil

  • Rojo-López, Gemma
[Resumo] Este traballo aborda o desenvolvemento de mesturas autocompactantes coa incorporación de materiais suplementarios procedentes de residuos industriais como substitutos de cemento para aumentar a sustentabilidade, así como a introdución de fibras para aumentar a vida útil das mesturas. Estes materiais propostos son cinza de biomasa e po de granito, que se consideran residuos industriais na "Eurorrexión Galicia-Norte de Portugal" e son abundantes. Dada a crecente presión social cara á xestión sostible dos residuos e a eficiencia dos recursos, o uso destes materiais suplementarios procedentes de residuos industriais axuda a alcanzar os obxectivos de mitigación de CO2 avanzando cara a unha economía circular. Neste sentido, este estudo desenvolveuse a nivel de pasta, morteiro e formigón, deseñando diferentes mesturas de base cemento e analizando o seu comportamento mediante técnicas de extracción de coñecemento e reoloxía para obter parámetros óptimos de dosificación. Ademais, para aumentar a vida útil das mesturas propostas, estudouse a inclusión de fibras metálicas e de polipropileno. Os resultados obtidos permitiron concluír que o uso de materiais cementantes suplementarios para aumentar a sustentabilidade das mesturas autocompactantes é unha boa opción. Ademais, a inclusión de fibras proporciona beneficios tanto ambientais como económicos sen inconvenientes significativos no comportamento fresco e endurecido dos formigóns., [Resumen] Este trabajo aborda el desarrollo de mezclas autocompactantes con la incorporación de materiales suplementarios procedentes de residuos industriales como sustitutos de cemento para aumentar la sostenibilidad, así como la introducción de fibras para aumentar la vida útil. Estos materiales propuestos son ceniza de biomasa y polvo de granito, que se consideran residuos industriales en la "Eurorregión Galicia-Norte de Portugal" y son abundantes. Dada la creciente presión social hacia la gestión sostenible de los residuos y la eficiencia de los recursos, el uso de estos materiales suplementarios procedentes de residuos industriales ayuda a alcanzar los objetivos de mitigación de CO2 avanzando hacia una economía circular. En este sentido, este estudio se ha desarrollado a nivel de pasta, mortero y hormigón, diseñando diferentes mezclas de base cemento y analizando su comportamiento mediante técnicas de extracción de conocimiento y reología para obtener parámetros óptimos de dosificación. Además, para aumentar la vida útil de las mezclas propuestas, se estudió la inclusión de fibras metálicas y de polipropileno. Los resultados obtenidos permitieron concluir que el uso de materiales cementantes suplementarios para aumentar la sostenibilidad de las mezclas autocompactantes es una buena opción. Además, la inclusión de fibras proporciona beneficios tanto medioambientales como económicos sin inconvenientes significativos en el comportamiento fresco y endurecido de los hormigones., [Abstract] This work addresses the development of self-compacting mixtures with the incorporation of supplementary materials from industrial waste as cement substitutes to increase sustainability, as well as the introduction of fibres to increase the service life of the mixtures. These proposed materials are biomass ash and granite powder, which are abundantly available and considered wastes from the local industry in the “Galicia–North of Portugal Euroregion”. Given the rising social pressure towards sustainable waste management and resource efficiency, the use of supplementary cementitious materials coming from industrial wastes helps to achieve CO2 mitigation goals advancing towards a circular economy. In this regard, this study was developed at the paste, mortar and concrete level, designing different cement-based mixtures and analysing their performance through knowledge extraction techniques and rheology to obtain the optimum dosage parameters. In addition, to increase the service life of the proposed mixtures, the inclusion of metallic and polypropylene fibres was studied. The results obtained led to the conclusion that the use of supplementary cementitious materials to increase the sustainability of self-compacting mixes is a good option. Moreover, the inclusion of fibres provides both environmental and economic gains without significant drawbacks in the fresh and hardened behaviour of the concretes., Este traballo desenvolveuse no marco do proxecto HORREO (Hormigones reciclados autocompactantes robustos: reología en estado fresco y propiedades mecánicas-BIA2014-58063-R) financiado polo Ministerio de Economía e Competitividade que contaba tamén con un contrato predoutoral para a formación de doutores (FPI, BES-2015-071919) que puiden desfrutar durante 4 anos. Para acadar a mención internacional teño que agradecer ao programa de estadías breves da FPI e ao programa IACOBUS pola financiación recibida para realizar dúas estadías de 3 meses na Facultade de Engenheria da Universidade do Porto (FEUP). Ademais, este traballo enmárcase tamén nos seguintes proxectos: Eco3DConcrete (Diseño de hormigón más sostenible para impresión 3D basado en la reología y el control de propiedades a muy cortas edades - PID2020-115433RB-I00), PREHEALING (Diseño de prefabricados de hormigón empleando estrategias sostenibles de auto reparación para incremento de su vida útil - PDC2021-121660-I00) e 3DHealConcrete (Aprovechamiento de sinergias entre las tecnologías de impresión 3D y estrategias de autorreparacion con bacterias para el diseño de hormigones sostenibles y durables -TED2021-129757B-I00) todos eles financiados polo Ministerio de Economía e Competitividade.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Assessment of Water Transport and Chemical Attack of Meta-Illite Calcined Clay Blended Cement in High-Performance Concrete

  • Nduka, David
  • Olawuyi, Babatunde James
  • Cantero, B.
  • González-Fonteboa, Belén
[Abstract:] Rapid urbanisation causes a rise in the need for infrastructure, which in turn fuels the creation of additional concrete and further increases cement supplies. Activation of illite-based clay mineral and usage in concrete production is one of the sustainable ways to address the cement industry anthropogenic issues. This study evaluates the durability properties of water transport (water absorption, and capillary water absorption), and resistance to aggressive environments (5% solutions of hydrochloric acid, HCl; sodium sulphate, Na2SO4; and calcium chloride, CaCl2) of meta-illite calcined clay (MCC)-based high-performance concrete (HPC). For this purpose, concrete was produced with 5, 10, 15, 20, 25 and 30% MCC content in partial substitution of CEM II. Results from the water absorption tests indicate an average percentage value of 3.57%, 3.35% and 2.52% for all the observed mixes at 28, 56 and 90 days, respectively, with MCCC-10 HPC having an average best value of 2.23% across the curing ages. On all observed days, the 5 to 15% cement replacements had very close average water sorptivity value of 0.125 ± 0.001 mm/min0.5 with the control mix (0.113 ± 0.011 mm/min0.5). The aggressive environments exposure findings of the hardened MCC-based HPC specimens of 10 to 20% recorded an approximately 15% compressive strength loss in HCl, Na2SO4 and CaCl2 solutions over the 90 days of curing. In all, the HPC mixes of 5 to 15% MCC content obtained an average durability performance factor of 89%. As a result, these findings imply that MCC can replace cement in up to 15% of HPC production., This research was funded by MINECO through two projects entitled: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)- PID2020-115433RB-I00” and “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)- PDC2021-121660-I00”. We also thank the Spanish Ministry of Science and Innovation for the financial support through its postdoctoral fellowship to Juan de la Cierva (No FJC2021-047024-I).
RUC. Repositorio da Universidade da Coruña
Publicación Tesis doctoral (DoctoralThesis)

Internal curing of high-performance concrete via waste-based porous materials, Curado interno de formigón de altas prestacións mediante materiais porosos en base a residuos

  • Rodríguez-Álvaro, Roberto
[Abstract] This work presents the use of different waste based porous materials as internal curing water reservoirs in high performance concrete, which is strongly aligned with the objective of promoting circularity in the construction industry. Internal curing was studied in combination with other shrinkage reduction strategies such as the use of coal fly ash as a low reactive supplementary cementitious material, and the use of a magnesium based expansive agent. The following waste based porous materials were used: ceramic recycled aggregates, mixed recycled aggregates, coal bottom ash and wood bottom ash. A conventional lightweight expanded clay aggregate was also used. The following properties were studied on the proposed mixtures: workability, hydration, setting, air content, density, porosity, strength, volume stability and durability. Internal curing via waste based porous materials can effectively mitigate autogenous shrinkage without significantly jeopardizing other properties. However, the alternative materials should be carefully characterized and the mix proportions should be studied in depth. Furthermore, it was concluded that external curing is needed even if internal curing is used, and synergistic effects were detected between the proposed shrinkage reduction strategies. Therefore, this work presents a feasible solution for a more durable and sustainable construction., [Resumen] Este trabajo propone el uso de diferentes materiales porosos procedentes de residuos como reservorios de agua de curado interno en el hormigón de altas prestaciones, lo cual está fuertemente alineado con el objetivo de promover la circularidad en la industria de la construcción. El curado interno se estudió en combinación con otras estrategias de reducción de la retracción como el uso de ceniza volante de carbón como material cementante suplementario de baja reactividad y el uso de un agente expansivo basado en magnesio. Como materiales porosos procedentes de residuos, se utilizaron los siguientes: áridos reciclados cerámicos, áridos reciclados mixtos, ceniza de fondo de carbón y ceniza de fondo de madera. También se utilizó un árido convencional de arcilla expandida. Se estudiaron las siguientes propiedades sobre las mezclas propuestas: trabajabilidad, hidratación, fraguado, contenido de aire, densidad, porosidad, resistencia, estabilidad de volumen y durabilidad. El curado interno a través de materiales porosos procedentes de residuos puede mitigar la retracción autógena sin perjudicar significativamente otras propiedades. Sin embargo, los materiales alternativos usados deben ser caracterizados cuidadosamente y las dosificaciones estudiadas en profundidad. Además, se concluyó que el curado externo es necesario, aunque se use el curado interno, y se detectaron efectos sinérgicos entre las distintas estrategias de reducción de la retracción propuestas. Por lo tanto este trabajo presenta una solución viable para una construcción más durable y sostenible., [Resumo] Este traballo propón o uso de diferentes materiais porosos procedentes de residuos como reservorios de auga de curado interno no formigón de altas prestación, o cal está fortemente aliñado co obxectivo de promover a circularidade na industria da construción. O curado interno estudiouse en combinación con outras estratexias de redución da retracción coma o uso da cinza voante de carbón como material cementante suplementario de baixa reactividade e o uso dun axente expansivo baseado en magnesio. Como materiais porosos procedentes de residuos, utilizáronse os seguintes: áridos reciclados cerámicos, áridos reciclados mixtos, cinza de fondo de carbón e cinza de fondo de madeira. Tamén se empregou un árido convencional de arxila expandida. Estudáronse as seguintes propiedades sobre as mesturas propostas: traballabilidade, hidratación, fraguado, contido de aire, porosidade, resistencia, estabilidade de volume e durabilidade. O curado interno a través de materiais porosos procedentes de residuos pode mitigar a retracción autóxena sen prexudicar significativamente outras propiedades. Non obstante, os materiais alternativos usados deben ser caracterizados coidadosamente e as dosificacións estudadas en profundidade. Ademais, concluíuse que o curado externo é necesario aínda que se use o curado interno, e detectáronse efectos sinérxicos entre as distintas estratexias de redución da retracción propostas. Polo tanto, este traballo presenta unha solución viable para unha construción máis durable e sostible.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Automated Control of the Fresh State of Industrial Concrete Behaviour by Rheometer Test Adjustment

  • Rojo-López, Gemma
  • González-Fonteboa, Belén
  • Carro-López, Diego
  • Martínez-Abella, Fernando
[Abstract:] This study aimed to develop a rheometer prototype and define a procedure for adjusting the automated control of the fresh state of concrete. Sixteen batches were produced, and their fresh behaviour was measured at different testing times by applying the Abrams cone and flow curve test (FCT) as the rheological protocol. During this test, the yield stress and plastic viscosity of the concretes were measured in relative units. The rheometer prototype was used to define a new protocol to select the most suitable rheometer impeller arrangement and optimal FCT configuration. This protocol considers the torque at the end of the breakdown period, torque reduction during the breakdown period, segregation, and negative values of the yield stress in relative units. This protocol also enabled an iterative adjustment procedure, facilitating the use of a rheometer for the automated control of the homogeneity and behaviour of fresh concrete, as well as real-time decision making., This research was funded by the Spanish Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación through three research projects entitled: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)—PID2020-115433RB-I00”, “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)—PDC2021-121660-I00” and “Exploiting the synergic effects between 3D printing and self-healing technologies to design sustainable and durable concrete (3DHealConcrete)—TED2021-129757B-I00”.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Genetic programming to understand the influence of new sustainable powder materials in the fresh performance of cement pastes

  • Rojo-López, Gemma
  • González-Fonteboa, Belén
  • Pérez Ordóñez, Juan Luis
  • Martínez-Abella, Fernando
[Abstract:] This study focused on pastes that incorporate metakaolin, biomass ash, and granite powder as supplementary cementitious materials to obtain specific expressions to predict rheological properties in pastes and to define the most appropriate dosage parameters using genetic programming. For this purpose, a dataset was developed following a central composite design, and some fresh properties were measured: Marsh cone and rheological properties, such as yield stress and plastic viscosity. The models generated by genetic programming presented robust statistical indices for the properties studied. The influence of supplementary cementitious materials on rheological properties was also analysed through a parametric analysis. After analysing the factors affecting paste rheology, it was concluded that the most important aspects affecting fresh behaviour were water demand and particle interaction, as well as the relation between both effects., This study is part of two projects entitled: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)- PID2020-115433RB-I00”, “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)- PDC2021-121660-I00” and "Exploiting the synergic effects between 3D printing and self-healing technologies to design sustainable and durable concrete (3DHealConcrete) - TED2021-129757B–I00" funded by MINECO.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Parametric Analysis in Sustainable Self-Compacting Mortars Using Genetic Programming

  • Rojo-López, Gemma
  • González-Fonteboa, Belén
  • Pérez Ordóñez, Juan Luis
  • Martínez-Abella, Fernando
[Abstract]: This study addresses the capabilities of genetic programming to predict the behaviour of cement-based mixtures by focusing on the influence of quaternary binders (incorporating metakaolin, biomass ash and granite powder as novel powder materials) on the rheological properties of self-compacting mixtures, including spread diameter in mini-cone test and time to flow in mini-funnel test. Using a previous dataset, GP techniques are applied to obtain predicted models and to compare them with those developed throughout analysis of variance. The results demonstrate that the equations obtained by the GP technique showed the best statistical indices for the analysed properties. Afterwards, a parametric analysis was performed to analyse the influence of the composition of quaternary binders on the fresh behaviour of mortar mixtures. The parametric analysis indicated that changes in the binder composition that increased granite powder content damage the fresh behaviour of the mortars (the funnel time increases, and the spread diameter decreases), being this negative effect more significant when the water content is low, and especially noteworthy in the Tfunnel time. It is concluded that genetic programming and design of experiments are powerful tools that can be used to analyse the influence of new raw materials in different mortar properties., This study is part of two projects entitled: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)- PID2020-115433RB-I00” and “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)-PDC2021-121660-I00” funded by MINECO.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Effects of bacteria-based self-healing nutrients on hydration and rheology of cement pastes

  • Pinto, Adonay
  • González-Fonteboa, Belén
  • Seara Paz, Sindy
  • Martínez-Abella, Fernando
[Abstract:] Crack openings in concrete lead to a reduction in its lifespan. Many authors have analysed different techniques that could repair cracks autonomously, being the use of bacteria one of the most promising approaches. Bacteria are often introduced with nutrients in the concrete mixes, and they may alter the cement hydration. In this study, the effects that calcium lactate, calcium nitrate, and yeast extract have on cement pastes during the early hours of hydration were analysed. To accomplish this, calorimetry, in situ X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Vicat and rheology techniques were employed. The results demonstrated that the addition of calcium lactate led to higher values of ettringite, which altered the rheological behaviour of the pastes. Moreover, when added at 4%, calcium lactate also delayed the setting time by inhibiting the reaction of silicates, a similar effect was observed when yeast extract was added. Lastly, the incorporation of nitrate accelerated the setting time., This work has been carried out within the framework of the following projects: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)- [PID2020-115433RB-I00]”, “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)- [PDC2021-121660-I00]” and “Exploiting the synergic effects between 3D printing and self-healing technologies to design sustainable and durable concrete (3DHealConcrete) [TED2021-129757B-I00]” all funded by MINECO (Ministry of Economy, Industry and Competitiveness). In addition, the authors would like to thank the Xunta de Galicia (Spain) for the financial support through its pre-doctoral contracts program.