Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Contribución de congreso (ConferenceOutput)

Evaluation of Spread-Spectrum Sequences in Ultrasonic Sonar for Indoor People Localization

  • García Requejo, Alejandro|||0000-0002-4955-8852
  • Pérez Rubio, María del Carmen|||0000-0001-8271-6843
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Wright, William M. D.
  • Murano, Santiago Emmanuel Francis
2024 IEEE International Symposium on Medical Measurements and Applications (MeMeA), 26-28 June 2024, Eindhoven, Netherlands., Device-free localization (DFL) systems enable non-intrusive indoor human location without the need to wear a sensor or tag. This can be particularly helpful in healthcare and assisted living applications based on monitoring vulnerable people to improve their quality of life in their own home. For this purpose, this work presents a DFL system based on an ultrasonic asynchronous multistatic sonar, installed on the ceiling, consisting of four transmitters and a receiver that estimates the 3D position of a person's head. The emitted signals propagated through the indoor space are acquired by the receiver, which processes them by means of different proposed methods to estimate the position. Each transmitter emits spread-spectrum signal pulses with good cross-correlation properties, providing an update time of 300 ms and asynchronous operation. Kasami, Zadoff-Chu and orthogonal chirp emission sequences are analyzed by simulation and experimental results. Hence, it can be determined that Zadoff-Chu and chirp stand out due to their performance in terms of Doppler tolerance and accuracy, reaching mean absolute errors of 4.5 cm and 3.5 cm with standard deviations of 0.6 cm and 2 cm, respectively. On the other hand, Zadoff-Chu offers better correlation properties, while chirp provides higher data availability due to its better transducer adaptation., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Contribución de congreso (ConferenceOutput)

Preliminary Unknown Appliance Detection using Convolutional Variational Auto-Encoders for AAL

  • Diego Otón, Laura De|||0000-0002-4939-2987
  • Fuentes Jiménez, David|||0000-0001-6424-4782
  • Pizarro Pérez, Daniel|||0000-0003-0622-4884
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Mari, Simone
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
2024 IEEE International Conference on Omni-layer Intelligent Systems (COINS), 29-31 July 2024, London, United Kingdom., The healthcare landscape is evolving, emphasising the importance of Active Assisted Living in addressing challenges presented by the ageing population. Integrating Non-Intrusive Load Monitoring provides insights into individual appliance usage patterns without additional sensors, enabling the detection of changes in daily activities that may reflect a person's health status. Within the effectiveness of this approach, adaptability is crucial as households evolve, discerning variations in energy consumption patterns caused by new or replaced electrical devices. For this reason, this work introduces a sophisticated hybrid approach combining deep learning and classic machine learning to classify household electrical loads and detect unknown loads using high-frequency electrical current signal data. Finally, while experimental results highlight areas for improvement, the findings suggest promising applications in household settings, marking a step forward in facing hurdles within the AAL context., Agencia Estatal de investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Fixed-point Processing for an IR Positioning System based on QADA Receivers

  • Moltó Orozco, David|||0000-0002-2790-3758
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
2022 IEEE 12th International Conference on Indoor Positioning and Indoor Navigation (IPIN), 5-8 September, 2022, Beijing, China., Indoor optical positioning systems have increased in popularity in recent years because they can provide centimeter accuracy in three dimensions (3D) utilizing light-emitting diodes (LEDs) and photoreceptors. This work presents the design of a positioning system, which is based on a set of four photoreceptors functioning as beacons at known places for a single LED to be positioned. However, it might be extended to additional emitters with some medium access control. The associated processing is explained, as well as the basic assumptions to be addressed when approaching its hardware implementation, such as the preliminary partitioning of tasks between hardware and software, and the fixed-point representation of the processing to be implemented in hardware. The system has been validated by simulation in a 2 × 2 × 3.4 m3 volume, yielding mean absolute errors around 0.004 m for the X and Y axes, and around 0.01 m for the Z-axis, as well as lower standard deviations than 0.004 m for the X and Y axes and 0.01 m for the Z-axis., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Combined infrared-ultrasonic positioning system to improve the data availability

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
This work was supported in part by MCIN/AEI/10.13039/501100011033 and EU “NextGenerationEU”/PRTR (ref. TED2021-131773B-I00) Proyectos, Many indoor positioning applications related to accurate monitoring and tracking targets require centimeter precision. Infrared (IR)- and ultrasound (US)-based systems represent a feasible approach providing high robustness against interference. Furthermore, their combination may achieve better performance by mitigating their complementary drawbacks, covering larger areas, and improving the availability of positioning measurements. In this context, this work presents the proposal and experimental evaluation of a tightly coupled fusion method that uses an extended Kalman filter (EKF) to merge an IR- and a US-based positioning system. An outlier detection method is considered to select measurements with an adequate performance. Experimental results reveal that the IR and US systems are unable to position in 4.08% and 26.06% of locations, whereas the combined IR -US system has 100% of availability. In addition, the merged solution achieves less than 4 cm of positioning error in 90% of cases, outperforming the IR and US systems when they work independently., Agencia Estatal de Investigación, Universidad de Alcalá, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Comparison of Neural Networks for High-Sampling Rate NILM Scenario

  • Diego Otón, Laura De|||0000-0002-4939-2987
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
2022 IEEE International Symposium on Medical Measurements and Applications (MeMeA), 22-24 June 2022, Messina, Italy., The common objective of techniques employed to identify the use of household appliances is related to energy efficiency and the reduction of energy consumption. In addition, through load monitoring it is possible to assess the degree of independence of tenants with minimal invasion of privacy and thus develop sustainable health systems capable of providing the required services remotely. Both approaches should initially deal with the load identification stage. For that purpose, this work presents three different solutions that take the events of the electrical current signal acquired at high frequency and process them for classification by using two different topologies of Artificial Neural Networks (ANN). The data of interest used as input for the ANN in the proposals are the normalized signal captured around the events, the images created by dividing that signal into sections and organizing them in a matrix, and the images coming from the Short Time Fourier Transform (STFT) of the signal around the event. The dataset BLUED is used to carry out the validation of the proposal, where some of the proposed architectures obtain an F1 score above 90% for more than fifteen devices under classification., Universidad de Alcalá, Agencia Estatal de Investigación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Activity monitoring and location sensory system for people with mild cognitive impairments

  • García Requejo, Alejandro|||0000-0002-4955-8852
  • Pérez Rubio, María del Carmen|||0000-0001-8271-6843
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
Cognitive impairment diseases are becoming more and more prevalent mainly due to population ageing and the increase in life expectancy. Sensory and monitoring systems may allow people with mild cognitive impairments (MCI) or at early stages of dementia to live at home for longer with more independence and security. This work presents a Wireless Sensor Network (WSN) based on wearables that obtains indoor and outdoor location and step information, reporting them over a LoRaWAN network. Each Wireless Wearable Sensor (WWS) uses a Global Navigation Satellite System module for outdoor positioning, a proposed indoor roomlevel localization system based on infrared sensors, an accelerometer for a step detector algorithm, and a LoRa (Long-Range) radio link to send the measured information with low power consumption achieving a large coverage range. These sensory data are recorded in a database and presented to the medical services and caregivers through a user web application. This can be used to detect anomalous changes in daily patients? routines, as well as to know the user?s position in cases where the patient may be disoriented. In addition, alerts are launched in caregivers? smartphones to report about any risky situation, such as the patient leaving an allowed area or staying in one place for too long. Therefore, the proposed sensory system may support and extend the ability of people with MCI or at early stages of dementia to live independently, it helps detect behavioural changes and it keeps caregivers? peace of mind., European Commission, Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Estimating energy consumption in households for non-intrusive elderly monitoring

  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Diego Otón, Laura De|||0000-0002-4939-2987
  • Pizarro Pérez, Daniel|||0000-0003-0622-4884
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
2023 IEEE International Workshop on Metrology for Living Environment (MetroLivEnv), 29-31 May 2023, Milano, Italy., Population ageing is becoming a key social issue in recent decades, particularly in Western countries, where this fact, together with the increase of life expectancy, has posed a significant strain on public finances and health services. In this context, many technological developments are often proposed to promote and support the independent living of elderly at their own homes, thus avoiding or postponing possible entries into social residences. Among them, smart meters provide a nonintrusive way to monitor and estimate the tenants" daily activities, by only using a single-point measurement in the mains at the entrance of the household. This work describes a regression approach to estimate the energy consumption of a house by means of a LSTM neural network. For that purpose, a pilot has been run on a house during six months in order to collect the electrical data, which will be used later to train the neural network. After that training, the network tries to estimate the energy consumption every 15 minutes, so any deviation between the predicted sample and the measured one might be used to detect anomalies in the daily routine of the tenant., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Dynamic Adjustment of Measurement Noise Covariance Matrix in an Infrared-based Positioning and Tracking System

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Moltó Orozco, David|||0000-0002-2790-3758
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Espinosa Zapata, Felipe|||0000-0003-1588-0947
2022 IEEE 12th International Conference on Indoor Positioning and Indoor Navigation (IPIN), 5-8 September, 2022, Beijing, China., The accuracy of optical positioning systems can be compromised by multiple factors (reflections, calibration, etc.). As an alternative to the triangulation, multilateration, or fingerprinting techniques typically used in these systems, stochastic estimation techniques can be used, such as Kalman Filters (KF) in its different variants. They estimate the receiver position based on the acquired measurements and the estimated positions in previous iterations. This work presents the evaluation of a 3D optical positioning system, based on four LED beacons and a quadrant receiver, using an Extended Kalman Filter (EKF). The implementation of a measurement noise covariance matrix that is adjusted depending on the angle and distance between transmitters and receiver, obtained in the previous iteration, is analysed. The receiver position estimation using both a dynamic and a static measurement noise covariance matrix is evaluated and compared with simulations and experimental tests. In simulations, the achieved errors are below 6 cm and 12 cm in 75% of the cases when using a dynamic and a static noise matrix, respectively. In the experimental tests, the obtained errors in 75% of the cases for the position in plane XY and the rotation angle ? are smaller than 7.44 cm and 1.06 ? with a dynamic noise matrix; and below 7.59 cm and 1.62 ? for a static one., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Centralized optical 3D positioning system for emitting tags

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Moltó Orozco, David|||0000-0002-2790-3758
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Cubero Vacas, Miguel
13th International Conference on Indoor Positioning and Indoor Navigation (IPIN2023), 25-28 September 2023, Nuremberg, Germany., The demand for accurate and reliable local positioning systems has grown rapidly with the increasing use of Location-Based Services (LBS). Emerging technologies such as optical, RF, acoustic, mechanical, and magnetic are feasible options for indoor positioning. Optical-based systems have gained attention due to the widespread LED lamp availability and centimeter-level accuracy. In this context, this work presents the implementation and validation of a centralized optical Local Positioning System (LPS) based on a set of mobile emitter LEDs and a minimum of two fixed receivers, enabling simultaneous position of all tags in the infrastructure (centralized approach). The system is designed for long-distance measurements, using Visible or Infrared Light signals. By incorporating geometric considerations into a Non-Linear Least Squares Estimator (NLSE), the system can estimate the 3D position of a mobile object (i.e. person, drone). The comparison of different deployments demonstrates that the proposed system estimates the 3D position with less than 4mm of error in 90% of cases when using four non-aligned receivers and a single LED., Agencia Estatal de Investigación, Universidad de Alcalá, Junta de Comunidades de Castilla-La Mancha, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Multisensory system for long-term activity monitoring to facilitate aging-in-place

  • Lluva Plaza, Sergio|||0000-0002-0050-2807
  • Jiménez Martín, Ana|||0000-0003-0713-0054
  • Gualda Gómez, David|||0000-0003-2071-6260
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • García Domínguez, Juan Jesús|||0000-0002-7121-8651
Demographic changes and an ageing population require more effective methods to confront the increased prevalence of chronic diseases which generate dependence in older adults as well as an important rise in social expenditure. The challenge is not only to increase life expectancy, but also to ensure that the older adults can fully enjoy that moment in their lives, living where they wish to (private home, nursing home, …). Physical activity (PA) is a representative parameter of a person’s state of health, especially when we are getting older, because it plays an important role in the prevention of diseases, and that is the reason why it is promoted in older adults. One of the goals of this work is to assess the feasibility of objectively measuring the PA levels of older adults wherever they live. In addition, this work proposes long-term monitoring that helps to gather daily activity patterns. We fuse inertial measurements with other technologies (WiFi- and ultrasonic-based location) in order to provide not only PA, but also information about the place where the activities are carried out, including both room-level location and precise positioning (depending on the technology used). With this information, we would be able to generate information about the person’s daily routines which can be very useful for the early detection of physical or cognitive impairment., Junta de Comunidades de Castilla-La Mancha, Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Contribución de congreso (ConferenceOutput)

Appliance Identification in NILM Applications by means of a Convolutional Auto-Encoder

  • Diego Otón, Laura de|||0000-0002-4939-2987
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Pizarro Pérez, Daniel|||0000-0003-0622-4884
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
2023 IEEE International Workshop on Metrology for Living Environment (MetroLivEnv), 29-31 May 2023, Milano, Italy., In energy efficiency applications, Non-Intrusive Load Monitoring techniques (NILM) are typically used to deduce which electrical loads are being used in a building at a given time. The identification of household appliances, in particular manually operated ones, is relevant information that can also be applied to infer the routines of tenants in Active and Assisted Living environments (AAL). These tools and applications are becoming increasingly interesting, especially in Western countries, where the ageing population is putting a strain on public social and health services. In this context, this work aims to classify the on/off events of the devices considered in the BLUED database. For this purpose, an architecture is presented, consisting of a Convolutional Auto-Encoder (CAE) followed by a classifier neural network. The CAE is used to implement a dimensionality reduction process after the encoder. Input data are formatted as images, created with extracted sections of the high-frequency electric current signal captured around the switching events. It is noteworthy that this dimensionality reduction also allows a decrease in the computational load of the classifier. Regarding the CAE functionality, the reconstruction error reaches a value of 1.579 · 10−3, whereas in the validation stage a weighted average classification F1-score of 87 % is obtained for the whole architecture., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Evaluating Human Activity and Usage Patterns of Appliances with Smart Meters

  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Diego Otón, Laura De|||0000-0002-4939-2987
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
  • Pizarro Pérez, Daniel|||0000-0003-0622-4884
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
  • Bahíllo Martínez, Alfonso
2022 IEEE International Symposium on Medical Measurements and Applications (MeMeA), 22-24 June 2022, Messina, Italy., Population ageing is becoming a key issue for most western countries, due to the challenges that it poses to the sustainability of future healthcare systems. In this context, many proposals and development are emerging trying to enhance the independent living of elderly and cognitive impaired people at their own homes. For that purpose, the massive deployment of smart meter at houses and buildings, initially focused on improving the energy management, has become a useful tool to provide the society with a variety of services and applications that can be employed for independent living. This work proposes the use of a commercial smart meter that delivers the disaggregated consumption per appliance every hour. This device has been installed on a test house during a training period of two months, in order to infer the behavior routines in the usage of the microwave. After the training, every new day can be compared to the obtained usage pattern of that appliance, in order to launch a notification when the day routine significantly differs. Similarly, since the use of the microwave is related to cooking, activities such as breakfast, lunch or dinner, may also be monitored and/or compared to a trained pattern. The proposal has been validated preliminary with experimental data coming from the aforementioned household., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

High-rate acquisition system for an infrared LPS

  • Cubero Vacas, Miguel
  • Moltó Orozco, David|||0000-0002-2790-3758
  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
2023 38th Conference on Design of Circuits and Integrated Systems (DCIS), 15-17 November 2023, Málaga, Spain., In the last years, the demand for positioning systems based on visible light, infrared light or, in general, optical signals has increased considerably due to their high accuracy and low cost compared to positioning systems based on other technologies, as well as their ease of integration due to their wide presence in domestic and industrial environments. The main constraint of these solutions is that the high speed of light makes the acquisition process complex. This work proposes a complete acquisition architecture for the twelve signals coming from four QADA (Quadrature Angular Diversity Aperture) photoreceptors, based on an analog front-end for signal conditioning at the input, an analog-to-digital converter, and a final digital stage using an FPGA for the acquisition of the data coming from the converter with high data rates up to 16.25 Msps. To verify the system performance, LS (Loosely Synchronized) sequences, often used in positioning systems, are emitted by a LED, and, later, they are acquired and digitally processed successfully by the proposed architecture in some preliminary experimental tests., Agencia Estatal de Investigación, Universidad de Alcalá, Junta de Comunidades de Castilla-La Mancha, European Science Foundation
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Simulation tool and online demonstrator for CDMA-based Ultrasonic Indoor Localization Systems

  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Gualda Gómez, David|||0000-0003-2071-6260
  • Murano, Santiago Emmanuel Francis
  • Vicente Ranera, Jorge De
  • Ciudad Fernández, Francisco
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
This work presents the CODEUS platform, which includes a simulation tool together with an online experimental demonstrator to offer analysis and testing flexibility for researchers and developers in Ultrasonic Indoor Positioning Systems (UIPSs). The simulation platform allows most common encoding techniques and sequences to be tested in a configurable UIPS. It models the signal modulation and processing, the ultrasonic transducers? response, the beacon distribution, the channel propagation effects, the synchronism, and the application of different positioning algorithms. CODEUS provides results and performance analysis for different metrics and at different stages of the signal processing. The UIPS simulation tool is specified by means of the MATLAB© App-Designer environment, which enables the definition of a user-friendly interface. It has also been linked to an online demonstrator that can be managed remotely by means of a website, thus avoiding any hardware requirement or equipment on behalf of researchers. This demonstrator allows the selected transmission schemes, modulation or encoding techniques to be validated in a real UIPS, therefore enabling a fast and easy way of carrying out experimental tests in a laboratory environment, while avoiding the time-consuming tasks related to electronic design and prototyping in the UIPS field. Both simulator and online demonstrator are freely available for researchers and students through the corresponding website., Universidad de Alcalá, Agencia Estatal de Investigación