Pasar al contenido principal

MEJORANDO Y FOMENTANDO LA VIDA ACTIVA Y BIENESTAR DE LAS PERSONAS CON DEMENCIA Y DETERIORO COGNITIVO LEVE MEDIANTE EL USO DE TECNICAS DE LOCALIZACION

PID2019-105470RA-C33

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ALCALA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Design, Calibration, and Evaluation of a Long-Range 3-D Infrared Positioning System Based on Encoding Techniques

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
Optical indoor positioning systems have experienced an increasing research interest during last years as they can provide 3D centimeter accuracy using LED lighting. In the case of having several LEDs emitting simultaneously and a receiver (e.g. the tag to be localized), these systems face important challenges, such as very high dynamic ranges with low Signal-to-Noise Ratios when the coverage area is increased, Multiple Access Interference (MAI), multipath and near-far effects, calibration issues (misalignments in the receiver and other intrinsic parameters), and so on. Previous work have already shown the feasibility of using LED emitters in combination with Quadrature Angular Diversity Aperture (QADA) receivers to implement positioning systems. This work further introduces new design considerations, tested on an experimental setup, to enlarge the emitter-receiver range, thus increasing the total coverage, while dealing with the aforementioned challenges. The system applies encoding techniques to each transmitter to solve the multiple access problem. The performance of two different types of codes has been compared, as well as their influence on the final estimation of the receiver?s position: one based on Kasami sequences and another based on Loosely Synchronous (LS) codes, derived from Complementary Sets of Sequences. At the receiver, the estimation of the incident point is constrained to angles at which the system can be linearized, and a specific calibration process for this type of sensor has also been defined and applied. The proposal has been finally validated with both, simulated and experimental results, in a large space of 2 2m2 (base), with a distance from transmitters to receiver of 3:4m (height). The experimental tests at distances up to 4 m, carried out after the calibration process, achieve average absolute errors bellow 10 cm for X and Y axis and around 20 cm for Z, and standard deviations below 4 cm for X and Y , and around 30 cm for Z., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

A survey on acoustic positioning systems for location-based services

  • Aparicio Sosa, Joaquín
  • Álvarez Franco, Fernando Javier
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Holm, Sverre
Positioning systems have become increasingly popular in the last decade for location-based services, such as navigation, and asset tracking and management. As opposed to outdoor positioning, where the global navigation satellite system became the standard technology, there is no consensus yet for indoor environments despite the availability of different technologies, such as radio frequency, magnetic field, visual light communications, or acoustics. Within these options, acoustics emerged as a promising alternative to obtain high-accuracy low-cost systems. Nevertheless, acoustic signals have to face very demanding propagation conditions, particularly in terms of multipath and Doppler effect. Therefore, even if many acoustic positioning systems have been proposed in the last decades, it remains an active and challenging topic. This article surveys the developed prototypes and commercial systems that have been presented since they first appeared around the 1980s to 2022. We classify these systems into different groups depending on the observable that they use to calculate the user position, such as the time-of-flight, the received signal strength, or the acoustic spectrum. Furthermore, we summarize the main properties of these systems in terms of accuracy, coverage area, and update rate, among others. Finally, we evaluate the limitations of these groups based on the link budget approach, which gives an overview of the system's coverage from parameters such as source and noise level, detection threshold, attenuation, and processing gain., Agencia Estatal de Investigación, Research Council of Norway
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Fixed-point Processing for an IR Positioning System based on QADA Receivers

  • Moltó Orozco, David|||0000-0002-2790-3758
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
2022 IEEE 12th International Conference on Indoor Positioning and Indoor Navigation (IPIN), 5-8 September, 2022, Beijing, China., Indoor optical positioning systems have increased in popularity in recent years because they can provide centimeter accuracy in three dimensions (3D) utilizing light-emitting diodes (LEDs) and photoreceptors. This work presents the design of a positioning system, which is based on a set of four photoreceptors functioning as beacons at known places for a single LED to be positioned. However, it might be extended to additional emitters with some medium access control. The associated processing is explained, as well as the basic assumptions to be addressed when approaching its hardware implementation, such as the preliminary partitioning of tasks between hardware and software, and the fixed-point representation of the processing to be implemented in hardware. The system has been validated by simulation in a 2 × 2 × 3.4 m3 volume, yielding mean absolute errors around 0.004 m for the X and Y axes, and around 0.01 m for the Z-axis, as well as lower standard deviations than 0.004 m for the X and Y axes and 0.01 m for the Z-axis., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Combined infrared-ultrasonic positioning system to improve the data availability

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
This work was supported in part by MCIN/AEI/10.13039/501100011033 and EU “NextGenerationEU”/PRTR (ref. TED2021-131773B-I00) Proyectos, Many indoor positioning applications related to accurate monitoring and tracking targets require centimeter precision. Infrared (IR)- and ultrasound (US)-based systems represent a feasible approach providing high robustness against interference. Furthermore, their combination may achieve better performance by mitigating their complementary drawbacks, covering larger areas, and improving the availability of positioning measurements. In this context, this work presents the proposal and experimental evaluation of a tightly coupled fusion method that uses an extended Kalman filter (EKF) to merge an IR- and a US-based positioning system. An outlier detection method is considered to select measurements with an adequate performance. Experimental results reveal that the IR and US systems are unable to position in 4.08% and 26.06% of locations, whereas the combined IR -US system has 100% of availability. In addition, the merged solution achieves less than 4 cm of positioning error in 90% of cases, outperforming the IR and US systems when they work independently., Agencia Estatal de Investigación, Universidad de Alcalá, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Comparison of Neural Networks for High-Sampling Rate NILM Scenario

  • Diego Otón, Laura De|||0000-0002-4939-2987
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
2022 IEEE International Symposium on Medical Measurements and Applications (MeMeA), 22-24 June 2022, Messina, Italy., The common objective of techniques employed to identify the use of household appliances is related to energy efficiency and the reduction of energy consumption. In addition, through load monitoring it is possible to assess the degree of independence of tenants with minimal invasion of privacy and thus develop sustainable health systems capable of providing the required services remotely. Both approaches should initially deal with the load identification stage. For that purpose, this work presents three different solutions that take the events of the electrical current signal acquired at high frequency and process them for classification by using two different topologies of Artificial Neural Networks (ANN). The data of interest used as input for the ANN in the proposals are the normalized signal captured around the events, the images created by dividing that signal into sections and organizing them in a matrix, and the images coming from the Short Time Fourier Transform (STFT) of the signal around the event. The dataset BLUED is used to carry out the validation of the proposal, where some of the proposed architectures obtain an F1 score above 90% for more than fifteen devices under classification., Universidad de Alcalá, Agencia Estatal de Investigación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Definition of a FPGA-based SoC architecture for PRBS transmission in optical spectroscopy

  • Tapiador Luque, Miguel
  • Escobar Vera, Camilo José
  • Soriano Amat, Miguel|||0000-0002-4819-3898
  • Martín López, Sonia|||0000-0001-5203-6206
  • González Herráez, Miguel|||0000-0003-2555-2971
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Fernández Ruiz, María del Rosario|||0000-0003-3561-2405
Optical spectroscopy is a well-known tool typically employed for characterizing the properties of materials by analyzing their iteration with light. One of the most spread techniques is the dual comb spectroscopy, since it accomplishes ultra-high resolution, and high sensitivity measurements with a relatively simple platform including a single, relatively narrowband photodetector. The employed optical dual comb can be implemented through electro-optical (EO) modulation driven by pseudo-ransom binary sequences (PRBS) at high data rates, commonly in the range of tens of Gbps. For that purpose, the runtime generation and transmission of adaptive PRBS is still an open challenge, often involving expensive and not flexible high-speed digital systems, with a few commercially available solutions that sometimes do not match the application requirements efficiently. In this context, this work describes the definition and implementation of a System-on-Chip (SoC) architecture, based on a FPGA device, capable of generating and transmitting two PRBS for a dual comb, at a data rate up to 5 Gbps. The architecture can be configured and its operation modified in run time, thanks to the general-purpose processor involved, in charge of managing an Ethernet link to receive new PRBS to be transmitted or set up certain parameters. The proposed design has been validated experimentally on a dual comb spectroscopy measurement, where the absorption of a hydrogen cyanide (HCN) gas cell has been successfully characterized., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

LOCATE-US: Indoor Positioning for Mobile Devices Using Encoded Ultrasonic Signals, Inertial Sensors and Graph- Matching

  • Gualda Gómez, David|||0000-0003-2071-6260
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Pérez Bachiller, Sergio
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • García Domínguez, Juan Jesús|||0000-0002-7121-8651
  • Jiménez Martín, Ana|||0000-0003-0713-0054
Indoor positioning remains a challenge and, despite much research and development carried out in the last decade, there is still no standard as with the Global Navigation Satellite Systems (GNSS) outdoors. This paper presents an indoor positioning system called LOCATE-US with adjustable granularity for use with commercial mobile devices, such as smartphones or tablets. LOCATE-US is privacy-oriented and allows every device to compute its own position by fusing ultrasonic, inertial sensor measurements and map information. Ultrasonic Local Positioning Systems (ULPS) based on encoded signals are placed in critical zones that require an accuracy below a few decimeters to correct the accumulated drift errors of the inertial measurements. These systems are well suited to work at room level as walls confine acoustic waves inside. To avoid audible artifacts, the U-LPS emission is set at 41.67 kHz, and an ultrasonic acquisition module with reduced dimensions is attached to the mobile device through the USB port to capture signals. Processing in the mobile device involves an improved Time Differences of Arrival (TDOA) estimation that is fused with the measurements from an external inertial sensor to obtain real-time location and trajectory display at a 10 Hz rate. Graph-matching has also been included, considering available prior knowledge about the navigation scenario. This kind of device is an adequate platform for Location-Based Services (LBS), enabling applications such as augmented reality, guiding applications, or people monitoring and assistance. The system architecture can easily incorporate new sensors in the future, such as UWB, RFiD or others., Universidad de Alcalá, Junta de Comunidades de Castilla-La Mancha, Agencia Estatal de Investigación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Evaluation of Multi-Sensor Fusion Methods for Ultrasonic Indoor Positioning

  • Mannay, Khaoula
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Machhout, Mohamed
  • Aguili, Taoufik
Indoor positioning systems have become a feasible solution for the current development of multiple location-based services and applications. They often consist of deploying a certain set of beacons in the environment to create a coverage volume, wherein some receivers, such as robots, drones or smart devices, can move while estimating their own position. Their final accuracy and performance mainly depend on several factors: the workspace size and its nature, the technologies involved (Wi-Fi, ultrasound, light, RF), etc. This work evaluates a 3D ultrasonic local positioning system (3D-ULPS) based on three independent ULPSs installed at specific positions to cover almost all the workspace and position mobile ultrasonic receivers in the environment. Because the proposal deals with numerous ultrasonic emitters, it is possible to determine different time differences of arrival (TDOA) between them and the receiver. In that context, the selection of a suitable fusion method to merge all this information into a final position estimate is a key aspect of the proposal. A linear Kalman filter (LKF) and an adaptive Kalman filter (AKF) are proposed in that regard for a loosely coupled approach, where the positions obtained from each ULPS are merged together. On the other hand, as a tightly coupled method, an extended Kalman filter (EKF) is also applied to merge the raw measurements from all the ULPSs into a final position estimate. Simulations and experimental tests were carried out and validated both approaches, thus providing average errors in the centimetre range for the EKF version, in contrast to errors up to the meter range from the independent (not merged) ULPSs., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Activity monitoring and location sensory system for people with mild cognitive impairments

  • García Requejo, Alejandro|||0000-0002-4955-8852
  • Pérez Rubio, María del Carmen|||0000-0001-8271-6843
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
Cognitive impairment diseases are becoming more and more prevalent mainly due to population ageing and the increase in life expectancy. Sensory and monitoring systems may allow people with mild cognitive impairments (MCI) or at early stages of dementia to live at home for longer with more independence and security. This work presents a Wireless Sensor Network (WSN) based on wearables that obtains indoor and outdoor location and step information, reporting them over a LoRaWAN network. Each Wireless Wearable Sensor (WWS) uses a Global Navigation Satellite System module for outdoor positioning, a proposed indoor roomlevel localization system based on infrared sensors, an accelerometer for a step detector algorithm, and a LoRa (Long-Range) radio link to send the measured information with low power consumption achieving a large coverage range. These sensory data are recorded in a database and presented to the medical services and caregivers through a user web application. This can be used to detect anomalous changes in daily patients? routines, as well as to know the user?s position in cases where the patient may be disoriented. In addition, alerts are launched in caregivers? smartphones to report about any risky situation, such as the patient leaving an allowed area or staying in one place for too long. Therefore, the proposed sensory system may support and extend the ability of people with MCI or at early stages of dementia to live independently, it helps detect behavioural changes and it keeps caregivers? peace of mind., European Commission, Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Estimating energy consumption in households for non-intrusive elderly monitoring

  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Diego Otón, Laura De|||0000-0002-4939-2987
  • Pizarro Pérez, Daniel|||0000-0003-0622-4884
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
2023 IEEE International Workshop on Metrology for Living Environment (MetroLivEnv), 29-31 May 2023, Milano, Italy., Population ageing is becoming a key social issue in recent decades, particularly in Western countries, where this fact, together with the increase of life expectancy, has posed a significant strain on public finances and health services. In this context, many technological developments are often proposed to promote and support the independent living of elderly at their own homes, thus avoiding or postponing possible entries into social residences. Among them, smart meters provide a nonintrusive way to monitor and estimate the tenants" daily activities, by only using a single-point measurement in the mains at the entrance of the household. This work describes a regression approach to estimate the energy consumption of a house by means of a LSTM neural network. For that purpose, a pilot has been run on a house during six months in order to collect the electrical data, which will be used later to train the neural network. After that training, the network tries to estimate the energy consumption every 15 minutes, so any deviation between the predicted sample and the measured one might be used to detect anomalies in the daily routine of the tenant., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Design of a complete simulator for underwater acoustic localization systems based on spread-spectrum signals

  • Murano, Santiago Emmanuel Francis
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
  • Aparicio Sosa, Joaquín
  • Gualda Gómez, David|||0000-0003-2071-6260
  • Vicente Ranera, Jorge De
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
Deploying prototype positioning systems in underwater environments is expensive and an especially challenging task, so a first common approach is to carry out simulated studies to evaluate the requirements and restrictions imposed by the environment. In this regard, it is helpful to have simulation models that allow the generation of a wide range of tests as a previous step to any experimental prototype implementation. For that purpose, this work focuses on the design of a simulation tool that facilitates research on underwater positioning systems by considering several parameters and features, such as the design of the signals emitted by the acoustic transducers (encoding techniques, modulation schemes, etc.), the frequency response and location of emitters and hydrophones, the bathymetry of the seabed, and the channel effects on the ultrasonic signal propagation, implemented in a model based on ray tracing for the propagation of acoustic signals. The simulation tool has been validated through a complete set of tests for different configurations and situations, analyzing the signals involved at different processing stages: baseband, modulated signals, received signals, and final estimated positions. This simulation tool is a valuable asset to research different positioning system configurations or to illustrate several concepts in a pedagogical context., Universidad de Alcalá, Agencia Estatal de Investigación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Comparative analysis of neural network implementations for NILM applications

  • Martín Catalán, Jorge
  • Diego Otón, Laura De|||0000-0002-4939-2987
  • Tapiador Luque, Miguel
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
2023 38th Conference on Design of Circuits and Integrated Systems (DCIS), 15-17 November 2023, Málaga, Spain., Non-Intrusive Load Monitoring (NILM) comprises a set of techniques that try to disaggregate the energy consumption in a household or building, based on the measurements coming from a single-point smart meter. In this process, a key step is the load identification of the different appliances that may switched on/off during a certain interval under analysis. For that purpose, machine-learning techniques, including deep neural networks, have recently been involved. These classification algorithms may often imply a high computational cost, that might compromise a possible edge-computing implementation on the local smart meters. In this context, this work presents a preliminary comparison between two different real-time implementations of both neural networks, a dense one and a convolutional one, applied to load classification. The implementations are based on a FPGA approach and on a processor. In general terms, preliminary results show that the FPGA solution provides lower latencies than the processor one, at the expense of requiring a higher design effort and a quantization error coming from the fixed-point representation., Agencia Estatal de Investigación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Using Perspective-n-Point Algorithms for a Local Positioning System Based on LEDs and a QADA Receiver

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Pizarro Pérez, Daniel|||0000-0003-0622-4884
  • Moltó Orozco, David|||0000-0002-2790-3758
The research interest on location-based services has increased during the last years ever since 3D centimetre accuracy inside intelligent environments could be confronted with. This work proposes an indoor local positioning system based on LED lighting, transmitted from a set of beacons to a receiver. The receiver is based on a quadrant photodiode angular diversity aperture (QADA) plus an aperture placed over it. This configuration can be modelled as a perspective camera, where the image position of the transmitters can be used to recover the receiver?s 3D pose. This process is known as the perspective-n-point (PnP) problem, which is well known in computer vision and photogrammetry. This work investigates the use of different state-of-the-art PnP algorithms to localize the receiver in a large space of 2 2m2 based on four co-planar transmitters and with a distance from transmitters to receiver up to 3.4 m. Encoding techniques are used to permit the simultaneous emission of all the transmitted signals and their processing in the receiver. In addition, correlation techniques (match filtering) are used to determine the image points projected from each emitter on the QADA. This work uses Monte Carlo simulations to characterize the absolute errors for a grid of test points under noisy measurements, as well as the robustness of the system when varying the 3D location of one transmitter. The IPPE algorithm obtained the best performance in this configuration. The proposal has also been experimentally evaluated in a real setup. The estimation of the receiver's position at three particular points for roll angles of the receiver of g ={0º, 120º, 210º and 300º} using the IPPE algorithm achieves average absolute errors and standard deviations of 4.33 cm, 3.51cm and 28.90 cm; and 1.84 cm, 1.17cm and 19.80cm in the coordinates x, y and z, respectively. These positioning results are in line with those obtained in previous work using triangulation techniques but with the addition that the complete pose of the receiver (x, y, z, a, b, g) is obtained in this proposal., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Dynamic Adjustment of Measurement Noise Covariance Matrix in an Infrared-based Positioning and Tracking System

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Moltó Orozco, David|||0000-0002-2790-3758
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Espinosa Zapata, Felipe|||0000-0003-1588-0947
2022 IEEE 12th International Conference on Indoor Positioning and Indoor Navigation (IPIN), 5-8 September, 2022, Beijing, China., The accuracy of optical positioning systems can be compromised by multiple factors (reflections, calibration, etc.). As an alternative to the triangulation, multilateration, or fingerprinting techniques typically used in these systems, stochastic estimation techniques can be used, such as Kalman Filters (KF) in its different variants. They estimate the receiver position based on the acquired measurements and the estimated positions in previous iterations. This work presents the evaluation of a 3D optical positioning system, based on four LED beacons and a quadrant receiver, using an Extended Kalman Filter (EKF). The implementation of a measurement noise covariance matrix that is adjusted depending on the angle and distance between transmitters and receiver, obtained in the previous iteration, is analysed. The receiver position estimation using both a dynamic and a static measurement noise covariance matrix is evaluated and compared with simulations and experimental tests. In simulations, the achieved errors are below 6 cm and 12 cm in 75% of the cases when using a dynamic and a static noise matrix, respectively. In the experimental tests, the obtained errors in 75% of the cases for the position in plane XY and the rotation angle ? are smaller than 7.44 cm and 1.06 ? with a dynamic noise matrix; and below 7.59 cm and 1.62 ? for a static one., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Centralized optical 3D positioning system for emitting tags

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Moltó Orozco, David|||0000-0002-2790-3758
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Cubero Vacas, Miguel
13th International Conference on Indoor Positioning and Indoor Navigation (IPIN2023), 25-28 September 2023, Nuremberg, Germany., The demand for accurate and reliable local positioning systems has grown rapidly with the increasing use of Location-Based Services (LBS). Emerging technologies such as optical, RF, acoustic, mechanical, and magnetic are feasible options for indoor positioning. Optical-based systems have gained attention due to the widespread LED lamp availability and centimeter-level accuracy. In this context, this work presents the implementation and validation of a centralized optical Local Positioning System (LPS) based on a set of mobile emitter LEDs and a minimum of two fixed receivers, enabling simultaneous position of all tags in the infrastructure (centralized approach). The system is designed for long-distance measurements, using Visible or Infrared Light signals. By incorporating geometric considerations into a Non-Linear Least Squares Estimator (NLSE), the system can estimate the 3D position of a mobile object (i.e. person, drone). The comparison of different deployments demonstrates that the proposed system estimates the 3D position with less than 4mm of error in 90% of cases when using four non-aligned receivers and a single LED., Agencia Estatal de Investigación, Universidad de Alcalá, Junta de Comunidades de Castilla-La Mancha, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Contribución de congreso (ConferenceOutput)

Conditioning stage of a QADA receiver for a large range IR positioning system

  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Moltó Orozco, David|||0000-0002-2790-3758
  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • García García, Juan Carlos|||0000-0002-9367-9475
2024 IEEE International Instrumentation and Measurement Technology Conference (I2MTC 2024), 20-23 May 2024, Glasgow, United Kingdom., Optical positioning systems in the infrared or visible spectrum find application in the tracking of people or mobile vehicles in indoor spaces. A line of research proposes the use of LED emitters, acting as tags to be positioned, and quadrant receivers (QADA, Quadrant Photodiode Angular Diversity Aperture) located at known positions in the infrastructure. These systems can operate at a measurement rate that can reach some MHz at relatively low cost. Apart from the challenge of high-speed processing, they must also deal with low and changing signal-to-noise ratios (measurements at short and long distances, with different transmitter-receiver angle of view, etc.). This paper deals with the design of the analog conditioning stage of a QADA receiver taking into account that it must operate in a linear area with large dynamic signal margins and provide three outputs, one sum signal and two differential signals, that must be amplified with identical gain, as the performance of the triangulation algorithms used in positioning depends on this. Each signal has a transimpedance amplifier with continuous and low-frequency backlight cancellation. Furthermore, an automatic gain control with a large dynamic range is applied to the sum signal and the gain derived over time is used to manage two variable gain amplifiers for the other two differential signals. Some results are presented that show the performance of the system., Universidad de Alcalá, Agencia Estatal de Investigación, Junta de Comunidades de Castilla-La Mancha
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Implementing a CNN in FPGA programmable logic for NILM application

  • Tapiador Luque, Miguel
  • Diego Otón, Laura De|||0000-0002-4939-2987
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
2023 38th Conference on Design of Circuits and Integrated Systems (DCIS), 15-17 November 2023, Málaga, Spain., Non-Intrusive Load Monitoring (NILM) techniques are gaining popularity in the field of energy savings. Generally implemented through the use of smart meters, the main challenge with these devices is that they operate at very low sampling rates. To address this issue, FPGA-based systems have been proposed to capture instantaneous currents and voltages at higher sampling frequencies in the kHz range. However, the limitation of these architectures lies in the fact that the acquired windows are often transmitted upstream to the cloud for the application of load classification algorithms based on machine learning, relying on high-bandwidth communications available onsite. This work proposes an alternative approach by implementing the classification algorithms in the same acquisition and processing system, by using custom convolutional neural networks on mid-range FPGA devices. Brevitas and FINN frameworks are used for the quantization-aware training, as well as for the generation of a peripheral that may be integrated into any FPGA-based SoC (System-on-Chip) architecture. The proposed approach allows the whole processing involved in NILM techniques to be integrated into a single embedded system. Preliminary experimental results demonstrate the effectiveness of the proposed approach., Agencia Estatal de Investigación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Contribución de congreso (ConferenceOutput)

Appliance Identification in NILM Applications by means of a Convolutional Auto-Encoder

  • Diego Otón, Laura de|||0000-0002-4939-2987
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Pizarro Pérez, Daniel|||0000-0003-0622-4884
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
2023 IEEE International Workshop on Metrology for Living Environment (MetroLivEnv), 29-31 May 2023, Milano, Italy., In energy efficiency applications, Non-Intrusive Load Monitoring techniques (NILM) are typically used to deduce which electrical loads are being used in a building at a given time. The identification of household appliances, in particular manually operated ones, is relevant information that can also be applied to infer the routines of tenants in Active and Assisted Living environments (AAL). These tools and applications are becoming increasingly interesting, especially in Western countries, where the ageing population is putting a strain on public social and health services. In this context, this work aims to classify the on/off events of the devices considered in the BLUED database. For this purpose, an architecture is presented, consisting of a Convolutional Auto-Encoder (CAE) followed by a classifier neural network. The CAE is used to implement a dimensionality reduction process after the encoder. Input data are formatted as images, created with extracted sections of the high-frequency electric current signal captured around the switching events. It is noteworthy that this dimensionality reduction also allows a decrease in the computational load of the classifier. Regarding the CAE functionality, the reconstruction error reaches a value of 1.579 · 10−3, whereas in the validation stage a weighted average classification F1-score of 87 % is obtained for the whole architecture., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Dynamic Adjustment of Weighted GCC-PHAT for Position Estimation in an Ultrasonic Local Positioning System

  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Ureña Ureña, Jesus|||0000-0003-1408-6039
  • García Domínguez, Juan Jesús|||0000-0002-7121-8651
  • Jiménez Martín, Ana|||0000-0003-0713-0054
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
Ultrasonic local positioning systems (ULPS) have been brought to the attention of researchers as one of the possibilities that can be used for indoor localization. Acoustic systems combine a suitable trade-off between precision, ease of development, and cost. This work proposes a method for measuring the time of arrival of encoded emissions from a set of ultrasonic beacons, which are used to implement an accurate ULPS. This method uses the generalized cross-correlation technique with PHAT filter and weighting factor b (GCC-PHAT-b). To improve the performance of the GCC-PHAT-b in encoded emission detection, the employment is proposed of mixed-medium multiple-access techniques, based on code division and time division multiplexing of beacon emissions (CDMA and TDMA respectively), and to dynamically adjust the PHAT filter weighting factor. The receiver position is obtained by hyperbolic multilateration from the time differences of arrival (TDoA) between a reference beacon and the rest, thus avoiding the need for receiver synchronization. The results show how the dynamic adaptation of the weighting factor significantly reduces positioning errors from 20 cm to 2 cm in 80% of measurements. The simulated and real experiments prove that the proposed algorithms improve the performance of the ULPS in situations with lower signal-to-noise ratios (SNR) than 0 dB and in environments where the multipath effect makes it difficult to correctly detect the encoded ultrasonic emissions., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Evaluating Human Activity and Usage Patterns of Appliances with Smart Meters

  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Diego Otón, Laura De|||0000-0002-4939-2987
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
  • Pizarro Pérez, Daniel|||0000-0003-0622-4884
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
  • Bahíllo Martínez, Alfonso
2022 IEEE International Symposium on Medical Measurements and Applications (MeMeA), 22-24 June 2022, Messina, Italy., Population ageing is becoming a key issue for most western countries, due to the challenges that it poses to the sustainability of future healthcare systems. In this context, many proposals and development are emerging trying to enhance the independent living of elderly and cognitive impaired people at their own homes. For that purpose, the massive deployment of smart meter at houses and buildings, initially focused on improving the energy management, has become a useful tool to provide the society with a variety of services and applications that can be employed for independent living. This work proposes the use of a commercial smart meter that delivers the disaggregated consumption per appliance every hour. This device has been installed on a test house during a training period of two months, in order to infer the behavior routines in the usage of the microwave. After the training, every new day can be compared to the obtained usage pattern of that appliance, in order to launch a notification when the day routine significantly differs. Similarly, since the use of the microwave is related to cooking, activities such as breakfast, lunch or dinner, may also be monitored and/or compared to a trained pattern. The proposal has been validated preliminary with experimental data coming from the aforementioned household., Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

High-rate acquisition system for an infrared LPS

  • Cubero Vacas, Miguel
  • Moltó Orozco, David|||0000-0002-2790-3758
  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
2023 38th Conference on Design of Circuits and Integrated Systems (DCIS), 15-17 November 2023, Málaga, Spain., In the last years, the demand for positioning systems based on visible light, infrared light or, in general, optical signals has increased considerably due to their high accuracy and low cost compared to positioning systems based on other technologies, as well as their ease of integration due to their wide presence in domestic and industrial environments. The main constraint of these solutions is that the high speed of light makes the acquisition process complex. This work proposes a complete acquisition architecture for the twelve signals coming from four QADA (Quadrature Angular Diversity Aperture) photoreceptors, based on an analog front-end for signal conditioning at the input, an analog-to-digital converter, and a final digital stage using an FPGA for the acquisition of the data coming from the converter with high data rates up to 16.25 Msps. To verify the system performance, LS (Loosely Synchronized) sequences, often used in positioning systems, are emitted by a LED, and, later, they are acquired and digitally processed successfully by the proposed architecture in some preliminary experimental tests., Agencia Estatal de Investigación, Universidad de Alcalá, Junta de Comunidades de Castilla-La Mancha, European Science Foundation
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Simulation tool and online demonstrator for CDMA-based Ultrasonic Indoor Localization Systems

  • Pérez Rubio, María Del Carmen|||0000-0001-8271-6843
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Gualda Gómez, David|||0000-0003-2071-6260
  • Murano, Santiago Emmanuel Francis
  • Vicente Ranera, Jorge De
  • Ciudad Fernández, Francisco
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Nieto Capuchino, Rubén|||0000-0002-8293-9665
This work presents the CODEUS platform, which includes a simulation tool together with an online experimental demonstrator to offer analysis and testing flexibility for researchers and developers in Ultrasonic Indoor Positioning Systems (UIPSs). The simulation platform allows most common encoding techniques and sequences to be tested in a configurable UIPS. It models the signal modulation and processing, the ultrasonic transducers? response, the beacon distribution, the channel propagation effects, the synchronism, and the application of different positioning algorithms. CODEUS provides results and performance analysis for different metrics and at different stages of the signal processing. The UIPS simulation tool is specified by means of the MATLAB© App-Designer environment, which enables the definition of a user-friendly interface. It has also been linked to an online demonstrator that can be managed remotely by means of a website, thus avoiding any hardware requirement or equipment on behalf of researchers. This demonstrator allows the selected transmission schemes, modulation or encoding techniques to be validated in a real UIPS, therefore enabling a fast and easy way of carrying out experimental tests in a laboratory environment, while avoiding the time-consuming tasks related to electronic design and prototyping in the UIPS field. Both simulator and online demonstrator are freely available for researchers and students through the corresponding website., Universidad de Alcalá, Agencia Estatal de Investigación