Pasar al contenido principal

INNOVACION Y RECICLAJE DE MEMBRANAS PARA EL TRATAMIENTO DE AGUA POR OSMOSIS DIRECTA Y DESTILACION EN MEMBRANA

CTM2015-65348-C2-2-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSIDAD COMPLUTENSE DE MADRID
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

Docta Complutense
Publicación Artículo científico (JournalArticle)

Superhydrophobic nanofibers electrospun by surface segregating fluorinated amphiphilic additive for membrane distillation

  • Khayet Souhaimi, Mohamed
  • García Payo, M. Carmen
  • Matsuura, T.
A facile route for the in situ surface modification and mechanical strength-enhancement of electrospun nanofibers is described. Blends of a host hydrophilic polymer, polysulfone (PSF), and small quantities of a fluorinated polyurethane additive (FPA) up to 6 wt% in the PSF blend were considered. During electrospinning, this additive undergoes spontaneous surface segregation resulting in nanofibers with an improved hydrophobic character attributed mainly to the detected fluorine-rich surface and enhanced mechanical properties. We report the effects of the fluorinated additive content in the blend on the morphological and structural characteristics of the electrospun nanofibrous mats (ENMs) including their inter-fiber space and void volume fraction. ENMs with a superhydrophobic surface could be prepared using at least 3 wt% FPA in the PSF blend. The ENMs were tested in desalination by membrane distillation (MD) and competitive permeate fluxes as high as 53.8 kg/m2h, with stable low permeate electrical conductivities (< 5.1 μS/cm), were achieved for the ENM prepared with 4.5 wt% FPA in the PSF blend, when the feed was 30 g/L NaCl aqueous solution and the transmembrane temperature difference was 60°C, without any inter-fiber space wetting being detected.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High-flux thin film composite PIM-1 membranes for butanol recovery: Experimental study and process simulations

  • Contreras-Martínez, Jorge
  • Mohsenpour, Sajjad
  • Ameen, Ahmed W.
  • Budd, Peter M.
  • García-Payo, Carmen
  • Khayet, Mohamed
  • Gorgojo, Patricia
Thin film composite (TFC) membranes of the prototypical polymer of intrinsic microporosity (PIM-1) have been prepared by dip-coating on a highly porous electrospun polyvinylidene fluoride (PVDF) nanofibrous support. Prior to coating, the support was impregnated in a non-solvent to avoid the penetration of PIM-1 inside the PVDF network. Different non-solvents were considered and the results were compared with those of the dry support. When applied for the separation of n-butanol/water mixtures by pervaporation (PV), the developed membranes exhibited very high permeate fluxes, in the range of 16.1–35.4 kg m–2 h–1, with an acceptable n-butanol/water separation factor of about 8. The PV separation index (PSI) of the prepared membranes is around 115, which is among the highest PSI values that have been reported so far. Hybrid PV-distillation systems have been designed and modeled in Aspen HYSYS using Aspen Custom Modeler for setting up the PIM-1 TFC and commercial PDMS membranes as a benchmark. The butanol recovery cost for the hybrid systems is compared with a conventional stand-alone distillation process used for n-butanol/water separation, and a 10% reduction in recovery cost was obtained., J.C.-M. is thankful for the grant received from the Spanish Ministry of Economy and Competitiveness and the European Social Fund. M.K., C.G.-P., and J.C.-M. appreciate the financial support from Spanish Ministry of Economy and Competitiveness through its project CTM2015-65348-C2-2-R and the Spanish Ministry of Science, Innovation, and Universities through its project RTI2018-096042-B-C22. S.M. thanks The University of Manchester for funding his Ph.D. studies. P.G. acknowledges the Spanish Ministry of Economy and Competitiveness and the European Social Fund through the Ramon y Cajal program (RYC2019-027060-I/AEI/10.13039/501100011033)., Peer reviewed
Docta Complutense
Publicación Artículo científico (JournalArticle)

Improvement of nanostructured electrospun membranes for desalination by membrane distillation technology

  • Essalhi, Mohamed
  • Khayet Souhaimi, Mohamed
  • Ismail, Norafiqah
  • Sundman, Ola
  • Tavajohi, Naser
A systematic study is carried out to determine the optimum electrospinning preparation condition to prepare an adequate electrospun nanofibrous membrane (ENM) for direct contact membrane distillation (DCMD). A structural properties investigation of ENM was carried out because of the significant impact of its architectural structure, nanofiber diameter, inter-fiber space and ENM thickness, on DCMD performance. The morphology, hydrophobicity, mechanical properties, crystallinity and DCMD desalination were investigated. A long-term DCMD experiment (100h) was carried out using 30 g/L NaCl aqueous solution, both in the feed and permeate side of the optimum ENM membrane to evaluate its potential to produce drinkable water in case of lack of distilled water, for instance in a remote area, emergency situation, and/or portable system. In this case, drinkable water could be produced after 28 h with a permeate flux of 57.5 kg/m2.h and a salt rejection factor greater than 99.9%. Another long-term DCMD experiment (65 h) was conducted using 30 g/L NaCl aquesous solution as feed but at a higher temperature and distilled water as permeate to evaluate the desalination stability, wettability and scaling of the optimum ENM. A permeate flux of 58.5 kg/m2.h was obtained with a salt rejection factor greater than 99.9%.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Optimization of UV-photografting factors in preparation of polyacrylic-polyethersulfone forward osmosis membrane using response surface methodology

  • Rahman, Ahmad Fikri Hadi Abdul
  • Khushairi, Zulsyazwan Ahmad
  • Seman, Mazrul Nizam Abu
  • Khayet Souhaimi, Mohamed
Commercial nanofiltration polyethersulfone (NF2) membrane was modified via ultraviolet (UV) photografting to prepare a high-performance forward osmosis (FO) membrane. The optimized condition of grafting parameters was obtained using central composite design (CCD) and response surface methodology (RSM). UV-photografting time and acrylic acid (AA) monomer concentration were the considered variables, while the two RSM responses were water permeate flux and reverse salt diffusion flux (RSD). Quadratic models were established between the responses and the independent parameters using analysis of variance (ANOVA). The membranes were characterized with functional group, morphology and surface roughness. The obtained optimum conditions were 2.81 min grafting time and 27.85 g/L AA monomer concentration. Under these conditions, a maximum water permeate flux of 1.52 +/- 0.04 L/m(2)center dot h was achieved with an RSD value of 10.09 +/- 0.36 g/m(2)center dot h. The optimized membrane exhibited a higher water flux compared to the unmodified NF2 membrane without any significant change of the RSD value.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Heat-treated optimized polysulfone electrospun nanofibrous membranes for high performance wastewater microfiltration

  • Arribas, P.
  • García Payo, M. Carmen
  • Khayet Souhaimi, Mohamed
  • Gil, L.
The structure and morphology of self-sustained electrospun nanofibrous membranes (ENMs) are key factors determining membrane performance for filtration applications. In this study, heat post-treatment (HPT) method was applied to modify the structural and morphological properties of polysulfone (PSU) ENMs, to improve their filtration performance and to obtain membranes suitable for wastewater treatment. The influence of the HPT temperature and time on the morphological structure of the PSU ENMs as well as on fouling and filtration performance was investigated. Microfiltration (MF) tests were conducted using humic acid model solutions with a concentration of 15 mg/L at pH 11. Increasing the HPT temperature or time, led to an increase of the mean nanofiber diameter along with a decrease of the mean size of the inter-fiber space, the void volume fraction and the water contact angle of the membranes. ENMs treated with a higher HPT temperature and a longer time exhibited higher nanofibers interconnectivity and a more compact structure with a smaller size of inter-fiber spaces. Under the same MF operating conditions, a commercial polyethersulfone (PES) MF membrane (HPWP, Millipore) had lower filtration performance (i.e. lower performance index, PI, 82 kg/m2 h) than the treated-optimized PSU ENMs (i.e. 147 and 133 kg/m2 h for ENMs 9 and 10, respectively). The obtained results confirm the good performance of the developed PSU ENMs for MF applications.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Hollow fibre polymeric membranes for desalination by membrane distillation technology: A review of different morphological structures and key strategic improvements

  • Pagliero, Marcello
  • Khayet Souhaimi, Mohamed
  • García Fernández, Loreto
  • García Payo, M. Carmen
Membrane distillation (MD) is a separation technology that is gaining increasing importance for desalination because of its optimal separation performance and its ability to treat highly concentrated saline solutions. Among all membrane morphological structures, hollow fibre (HF) exhibits some peculiar advantages, does not require any support to withstand the operation conditions and can be arranged in modules reaching high packing density and optimal fluid dynamics reducing both temperature and concentration polarization effects on MD desalination performance. In general, hollow fibre membranes are prepared by spinning a dope solution following different techniques. The HF membrane morphology can be tuned by modifying a large number of spinning conditions as well as by improving the membrane structure by preparing single layer, mixed matrix or dual layered hollow fibres. This review analyses the research studies developed so far on the design and preparation of different types of hollow fibres together with a critical evaluation of the effects of the involved preparation conditions on MD desalination performance, and some useful remarks to improve hollow fibre characteristics, desalination performance and thermal efficiency. Among the proposed HF for MD desalination, dual layered HF membranes exhibit high permeate fluxes up to 98.6 kg/m2 h with good salt rejection factors.
Docta Complutense
Publicación Artículo científico (JournalArticle)

High-Flux Thin Film Composite PIM-1 Membranes for Butanol Recovery: Experimental Study and Process Simulations

  • Contreras Martínez, Jorge
  • Mohsenpour, Sajjad
  • Ameen, Ahmed W
  • Budd, Peter M.
  • García Payo, M. Carmen
  • Khayet Souhaimi, Mohamed
  • Gorgojo, Patricia
Thin film composite (TFC) membranes of the prototypical polymer of intrinsic microporosity (PIM-1) have been prepared by dip-coating on a highly porous electrospun polyvinylidene fluoride (PVDF) nanofibrous support. Prior to coating, the support was impregnated in a non-solvent to avoid the penetration of PIM-1 inside the PVDF network. Different non-solvents were considered and the results were compared with those of the dry support. When applied for the separation of n-butanol/water mixtures by pervaporation (PV), the developed membranes exhibited very high permeate fluxes, in the range of 16.1–35.4 kg m–2 h–1, with an acceptable n-butanol/water separation factor of about 8. The PV separation index (PSI) of the prepared membranes is around 115, which is among the highest PSI values that have been reported so far. Hybrid PV-distillation systems have been designed and modeled in Aspen HYSYS using Aspen Custom Modeler for setting up the PIM-1 TFC and commercial PDMS membranes as a benchmark. The butanol recovery cost for the hybrid systems is compared with a conventional stand-alone distillation process used for n-butanol/water separation, and a 10% reduction in recovery cost was obtained.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Recycled reverse osmosis membranes for forward osmosis technology

  • Contreras Martínez, Jorge
  • García Payo, M. Carmen
  • Arribas, Paula
  • Rodríguez Sáez, Laura
  • Lejarazu Larrañaga, Amaia
  • García Calvo, Eloy
  • Khayet Souhaimi, Mohamed
An alternative use of end-of-life reverse osmosis (RO) membranes is proposed for forward osmosis (FO) application as recycled FO (RFO) membranes and transformed recycled FO (TRFO) membranes. Different passive cleaning protocols in pilot plant and laboratory scale were followed using sodium hypochlorite (NaClO) at different concentrations and exposure time. The RFO with the best performance was selected for its transformation by interfacial polymerization (IP) technique to improve further the FO performance. Both the morphological structure and transport properties of the RFO and TRFO membranes were studied by means of different characterization techniques. Although the RFO membranes are suitable for FO, the TRFO membranes are more competitive. The highest FO water permeate fluxes (12.21 kg/m2·h and 15.12 kg/m2·h) were obtained for the membrane recycled applying the highest NaClO exposure dose applied in pilot plant (106 ppm·h) followed by IP of a thin polyamide layer. These permeate fluxes were better or at least comparable to commercial membranes used under the same FO conditions. The results indicated that it is possible to use discarded RO membranes in FO technology for wastewater treatment after adequate treatment procedures extending their lifetime and contributing to a circular economy and sustainability in membrane science and related materials.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Cyclic olefin polymer membrane as an emerging material for CO2 capture in gas-liquid membrane contactor

  • Sabzekar, Malihe
  • Pourafshari Chenar, Mahdi
  • Khayet Souhaimi, Mohamed
  • García Payo, M. Carmen
  • Maghsoud, Zahra
  • Pagliero, Marcello
Porous flat sheet membranes were prepared with a commercial grade of cyclic olefin polymer (COP) for CO2 capture using membrane contactor (MC). The membranes were prepared via non-solvent induced phase separation technique using different types of additives, namely, polyvinylpyrrolidone (PVP), polyethylene glycol (PEG400) and sorbitan monooleate (Span 80), and coagulants (acetone and 70/30 wt% acetone/water mixture) were investigated. The prepared membranes were characterized in terms of the thickness (70–85 µm), porosity (50–80%), mean pore size (158–265 nm), bubble pore size (~ 0.6–12 µm), liquid entry pressure (1.67–4.55 bar), water contact angle (~ 94° - 111°), monoethanolamine (MEA) contact angle (~ 67° - 73°) and mechanical properties (tensile strength: 4.53 – 5.15 MPa, elongation at break: 4 – 8% and Young´s modulus: 190 – 232 MPa). The thermodynamic study of COP membranes proved that a fast phase inversion of the proposed system resulted in a more porous structure. The addition of PEG400 and Span 80 caused delayed demixing and influenced the morphological structure and MC performance. The structural and topographical characteristics of the membranes were also studied. The CO2 absorption test performed at 27 °C showed that the maximum CO2 absorption flux was around 16 × 10−5 mol/m2.s using 1 M MEA aqueous solution as absorbent with fixed liquid and gas flow rates at 150 L/h and 8.4 L/h, respectively. It was found that the considered additives enhanced the MC performance and affected the CO2 absorption flux.