Pasar al contenido principal

TRATAMIENTOS HIBRIDOS DE AGUAS RESIDUALES BASADOS EN MEMBRANAS RECICLADAS CON OBJETIVO DE DESCARGA LIQUIDA CERO (ZLD)

RTI2018-096042-B-C22

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD COMPLUTENSE DE MADRID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

Docta Complutense
Publicación Artículo científico (JournalArticle)

Development of Novel Electrospun Fibers Based on Cyclic Olefin Polymer

  • Sabzekar, Malihe
  • Pourafshari Chenar, Mahdi
  • Khayet Souhaimi, Mohamed
  • García Payo, M. Carmen
  • Mortazavi, Seyed Mohammadmahdi
  • Golmohammadi, Morteza
For the first time, a systematic study to investigate the electrospinnability of cyclic olefin polymer (COP) was performed. Different solvents and mixtures were tested together with different electrospinning parameters and post-treatment types to prepare bead-free fibers without defects. These were successfully obtained using a chloroform/chlorobenzene (40/60 wt.%) solvent mixture with a 15 wt.% COP polymer, a 1 mL/h polymer solution flow rate, a 15 cm distance between the needle and collector, and a 12 kV electric voltage. COP fibers were in the micron range and the hot-press post-treatment (5 MPa, 5 min and 120 & DEG;C) induced an integrated fibrous structure along with more junctions between fibers, reducing the mean and maximum inter-fiber space. When the temperature of the press post-treatment was increased (from 25 & DEG;C to 120 & DEG;C), better strength and less elongation at break of COP fibers were achieved. However, when applying a temperature above the COP glass temperature (Tg = 138 & DEG;C) the fibers coalesced, showing a mechanical behavior similar to a plastic film and a low elongation at break with a high strength. The addition of a high dielectric constant non-solvent, N,N-dimethylacetamide (DMAc), resulted in a considerable reduction in the COP fiber diameter. Based on the cloud point approach, it was found that the use of DMAc and the solvent chloroform or chlorobenzene improved the electrospinnability of COP polymer solution.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High-flux thin film composite PIM-1 membranes for butanol recovery: Experimental study and process simulations

  • Contreras-Martínez, Jorge
  • Mohsenpour, Sajjad
  • Ameen, Ahmed W.
  • Budd, Peter M.
  • García-Payo, Carmen
  • Khayet, Mohamed
  • Gorgojo, Patricia
Thin film composite (TFC) membranes of the prototypical polymer of intrinsic microporosity (PIM-1) have been prepared by dip-coating on a highly porous electrospun polyvinylidene fluoride (PVDF) nanofibrous support. Prior to coating, the support was impregnated in a non-solvent to avoid the penetration of PIM-1 inside the PVDF network. Different non-solvents were considered and the results were compared with those of the dry support. When applied for the separation of n-butanol/water mixtures by pervaporation (PV), the developed membranes exhibited very high permeate fluxes, in the range of 16.1–35.4 kg m–2 h–1, with an acceptable n-butanol/water separation factor of about 8. The PV separation index (PSI) of the prepared membranes is around 115, which is among the highest PSI values that have been reported so far. Hybrid PV-distillation systems have been designed and modeled in Aspen HYSYS using Aspen Custom Modeler for setting up the PIM-1 TFC and commercial PDMS membranes as a benchmark. The butanol recovery cost for the hybrid systems is compared with a conventional stand-alone distillation process used for n-butanol/water separation, and a 10% reduction in recovery cost was obtained., J.C.-M. is thankful for the grant received from the Spanish Ministry of Economy and Competitiveness and the European Social Fund. M.K., C.G.-P., and J.C.-M. appreciate the financial support from Spanish Ministry of Economy and Competitiveness through its project CTM2015-65348-C2-2-R and the Spanish Ministry of Science, Innovation, and Universities through its project RTI2018-096042-B-C22. S.M. thanks The University of Manchester for funding his Ph.D. studies. P.G. acknowledges the Spanish Ministry of Economy and Competitiveness and the European Social Fund through the Ramon y Cajal program (RYC2019-027060-I/AEI/10.13039/501100011033)., Peer reviewed
Docta Complutense
Publicación Artículo científico (JournalArticle)

Improvement of nanostructured electrospun membranes for desalination by membrane distillation technology

  • Essalhi, Mohamed
  • Khayet Souhaimi, Mohamed
  • Ismail, Norafiqah
  • Sundman, Ola
  • Tavajohi, Naser
A systematic study is carried out to determine the optimum electrospinning preparation condition to prepare an adequate electrospun nanofibrous membrane (ENM) for direct contact membrane distillation (DCMD). A structural properties investigation of ENM was carried out because of the significant impact of its architectural structure, nanofiber diameter, inter-fiber space and ENM thickness, on DCMD performance. The morphology, hydrophobicity, mechanical properties, crystallinity and DCMD desalination were investigated. A long-term DCMD experiment (100h) was carried out using 30 g/L NaCl aqueous solution, both in the feed and permeate side of the optimum ENM membrane to evaluate its potential to produce drinkable water in case of lack of distilled water, for instance in a remote area, emergency situation, and/or portable system. In this case, drinkable water could be produced after 28 h with a permeate flux of 57.5 kg/m2.h and a salt rejection factor greater than 99.9%. Another long-term DCMD experiment (65 h) was conducted using 30 g/L NaCl aquesous solution as feed but at a higher temperature and distilled water as permeate to evaluate the desalination stability, wettability and scaling of the optimum ENM. A permeate flux of 58.5 kg/m2.h was obtained with a salt rejection factor greater than 99.9%.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Optimization of UV-photografting factors in preparation of polyacrylic-polyethersulfone forward osmosis membrane using response surface methodology

  • Rahman, Ahmad Fikri Hadi Abdul
  • Khushairi, Zulsyazwan Ahmad
  • Seman, Mazrul Nizam Abu
  • Khayet Souhaimi, Mohamed
Commercial nanofiltration polyethersulfone (NF2) membrane was modified via ultraviolet (UV) photografting to prepare a high-performance forward osmosis (FO) membrane. The optimized condition of grafting parameters was obtained using central composite design (CCD) and response surface methodology (RSM). UV-photografting time and acrylic acid (AA) monomer concentration were the considered variables, while the two RSM responses were water permeate flux and reverse salt diffusion flux (RSD). Quadratic models were established between the responses and the independent parameters using analysis of variance (ANOVA). The membranes were characterized with functional group, morphology and surface roughness. The obtained optimum conditions were 2.81 min grafting time and 27.85 g/L AA monomer concentration. Under these conditions, a maximum water permeate flux of 1.52 +/- 0.04 L/m(2)center dot h was achieved with an RSD value of 10.09 +/- 0.36 g/m(2)center dot h. The optimized membrane exhibited a higher water flux compared to the unmodified NF2 membrane without any significant change of the RSD value.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Hollow fibre polymeric membranes for desalination by membrane distillation technology: A review of different morphological structures and key strategic improvements

  • Pagliero, Marcello
  • Khayet Souhaimi, Mohamed
  • García Fernández, Loreto
  • García Payo, M. Carmen
Membrane distillation (MD) is a separation technology that is gaining increasing importance for desalination because of its optimal separation performance and its ability to treat highly concentrated saline solutions. Among all membrane morphological structures, hollow fibre (HF) exhibits some peculiar advantages, does not require any support to withstand the operation conditions and can be arranged in modules reaching high packing density and optimal fluid dynamics reducing both temperature and concentration polarization effects on MD desalination performance. In general, hollow fibre membranes are prepared by spinning a dope solution following different techniques. The HF membrane morphology can be tuned by modifying a large number of spinning conditions as well as by improving the membrane structure by preparing single layer, mixed matrix or dual layered hollow fibres. This review analyses the research studies developed so far on the design and preparation of different types of hollow fibres together with a critical evaluation of the effects of the involved preparation conditions on MD desalination performance, and some useful remarks to improve hollow fibre characteristics, desalination performance and thermal efficiency. Among the proposed HF for MD desalination, dual layered HF membranes exhibit high permeate fluxes up to 98.6 kg/m2 h with good salt rejection factors.
Docta Complutense
Publicación Artículo científico (JournalArticle)

High-Flux Thin Film Composite PIM-1 Membranes for Butanol Recovery: Experimental Study and Process Simulations

  • Contreras Martínez, Jorge
  • Mohsenpour, Sajjad
  • Ameen, Ahmed W
  • Budd, Peter M.
  • García Payo, M. Carmen
  • Khayet Souhaimi, Mohamed
  • Gorgojo, Patricia
Thin film composite (TFC) membranes of the prototypical polymer of intrinsic microporosity (PIM-1) have been prepared by dip-coating on a highly porous electrospun polyvinylidene fluoride (PVDF) nanofibrous support. Prior to coating, the support was impregnated in a non-solvent to avoid the penetration of PIM-1 inside the PVDF network. Different non-solvents were considered and the results were compared with those of the dry support. When applied for the separation of n-butanol/water mixtures by pervaporation (PV), the developed membranes exhibited very high permeate fluxes, in the range of 16.1–35.4 kg m–2 h–1, with an acceptable n-butanol/water separation factor of about 8. The PV separation index (PSI) of the prepared membranes is around 115, which is among the highest PSI values that have been reported so far. Hybrid PV-distillation systems have been designed and modeled in Aspen HYSYS using Aspen Custom Modeler for setting up the PIM-1 TFC and commercial PDMS membranes as a benchmark. The butanol recovery cost for the hybrid systems is compared with a conventional stand-alone distillation process used for n-butanol/water separation, and a 10% reduction in recovery cost was obtained.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Recycled reverse osmosis membranes for forward osmosis technology

  • Contreras Martínez, Jorge
  • García Payo, M. Carmen
  • Arribas, Paula
  • Rodríguez Sáez, Laura
  • Lejarazu Larrañaga, Amaia
  • García Calvo, Eloy
  • Khayet Souhaimi, Mohamed
An alternative use of end-of-life reverse osmosis (RO) membranes is proposed for forward osmosis (FO) application as recycled FO (RFO) membranes and transformed recycled FO (TRFO) membranes. Different passive cleaning protocols in pilot plant and laboratory scale were followed using sodium hypochlorite (NaClO) at different concentrations and exposure time. The RFO with the best performance was selected for its transformation by interfacial polymerization (IP) technique to improve further the FO performance. Both the morphological structure and transport properties of the RFO and TRFO membranes were studied by means of different characterization techniques. Although the RFO membranes are suitable for FO, the TRFO membranes are more competitive. The highest FO water permeate fluxes (12.21 kg/m2·h and 15.12 kg/m2·h) were obtained for the membrane recycled applying the highest NaClO exposure dose applied in pilot plant (106 ppm·h) followed by IP of a thin polyamide layer. These permeate fluxes were better or at least comparable to commercial membranes used under the same FO conditions. The results indicated that it is possible to use discarded RO membranes in FO technology for wastewater treatment after adequate treatment procedures extending their lifetime and contributing to a circular economy and sustainability in membrane science and related materials.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Cyclic olefin polymer membrane as an emerging material for CO2 capture in gas-liquid membrane contactor

  • Sabzekar, Malihe
  • Pourafshari Chenar, Mahdi
  • Khayet Souhaimi, Mohamed
  • García Payo, M. Carmen
  • Maghsoud, Zahra
  • Pagliero, Marcello
Porous flat sheet membranes were prepared with a commercial grade of cyclic olefin polymer (COP) for CO2 capture using membrane contactor (MC). The membranes were prepared via non-solvent induced phase separation technique using different types of additives, namely, polyvinylpyrrolidone (PVP), polyethylene glycol (PEG400) and sorbitan monooleate (Span 80), and coagulants (acetone and 70/30 wt% acetone/water mixture) were investigated. The prepared membranes were characterized in terms of the thickness (70–85 µm), porosity (50–80%), mean pore size (158–265 nm), bubble pore size (~ 0.6–12 µm), liquid entry pressure (1.67–4.55 bar), water contact angle (~ 94° - 111°), monoethanolamine (MEA) contact angle (~ 67° - 73°) and mechanical properties (tensile strength: 4.53 – 5.15 MPa, elongation at break: 4 – 8% and Young´s modulus: 190 – 232 MPa). The thermodynamic study of COP membranes proved that a fast phase inversion of the proposed system resulted in a more porous structure. The addition of PEG400 and Span 80 caused delayed demixing and influenced the morphological structure and MC performance. The structural and topographical characteristics of the membranes were also studied. The CO2 absorption test performed at 27 °C showed that the maximum CO2 absorption flux was around 16 × 10−5 mol/m2.s using 1 M MEA aqueous solution as absorbent with fixed liquid and gas flow rates at 150 L/h and 8.4 L/h, respectively. It was found that the considered additives enhanced the MC performance and affected the CO2 absorption flux.