Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Direct Conversion of Cellulose into Alkyl Glycoside Surfactants

  • Puga, Alberto V.
  • Corma Canós, Avelino|||0000-0002-2232-3527
[EN] The one-step production of biodegradable alkyl glycoside (1-dodecyl mono- and oligoglucoside) surfactants from cellulose has been achieved by direct alcoholysis in fatty alcohol media under BrOnsted acid catalysis at near-ambient pressure. The fatty alcohol serves as both solvent and reagent. Addition of small amounts of water prevents dehydration events and thus minimises product and solvent degradation. Furthermore, high initial cellulose loadings and short thermal cycles enable moderate-to-high conversions and selectivities (up to approximate to 70%), and low solvent-to-product ratios., Financial support from the Spanish Government-MINECO through "Severo Ochoa" (SEV 2012-0267) is acknowledged. AVP also thanks the Spanish Government (Agencia Estatal de Investigacion) and the European Union (European Regional Development Fund) for a grant for young researchers (CTQ2015-74138-JIN, AEI/FEDER/UE).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Determination of the Evolution of Heterogeneous Single Metal Atoms and Nanoclusters under Reaction Conditions: Which Are the Working Catalytic Sites?

  • Liu, Lichen
  • MEIRA, DEBORA M.
  • Arenal, Raul
  • Puga, Alberto V.
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • Corma Canós, Avelino|||0000-0002-2232-3527
[EN] Identification of active sites in heterogeneous metal catalysts is critical for understanding the reaction mechanism at the molecular level and for designing more efficient catalysts. Because of their structural flexibility, subnanometric metal catalysts, including single atoms and clusters with a few atoms, can exhibit dynamic structural evolution when interacting with substrate molecules, making it difficult to determine the catalytically active sites. In this work, Pt catalysts containing selected types of Pt entities (from single atoms to clusters and nanoparticles) have been prepared, and their evolution has been followed, while they were reacting in a variety of heterogeneous catalytic reactions, including selective hydrogenation reactions, CO oxidation, dehydrogenation of propane, and photocatalytic H-2 evolution reaction. By in situ X-ray absorption spectroscopy, in situ IR spectroscopy, and high-resolution electron microscopy techniques, we will show that some characterization techniques carried out in an inadequate way can introduce confusion on the interpretation of coordination environment of highly dispersed Pt species. Finally, the combination of catalytic reactivity and in situ characterization techniques shows that, depending on the catalyst-reactant interaction and metal-support interaction, singly dispersed metal atoms can rapidly evolve into metal clusters or nanoparticles, being the working active sites for those abovementioned heterogeneous reactions., This work has been supported by the European Union through the European Research Council (grant ERC-AdG-2014-671093, SynCatMatch) and the Spanish government through the "Severo Ochoa Program" (SEV-2016-0683). L.L. thanks ITQ for providing a contract. The authors also thank Microscopy Service of UPV for the TEM and STEM measurements. This research used resources of the Advanced Photon Source, an Office of Science User Facility operated for the U.S. Department of Energy (DOE) Office of Science by Argonne National Laboratory, and was supported by the U.S. DOE under contract no. DE-AC02-06CH11357 and the Canadian Light Source and its funding partners. The HR STEM and STEM-EELS studies were conducted at the Laboratorio de Microscopias Avanzadas, Universidad de Zaragoza, Spain. R.A. acknowledges support from Spanish MINECO grant MAT2016-79776-P (AEI/FEDER, UE), from the Government of Aragon and the European Social Fund (grant number E13_17R, FEDER, UE), and from the European Union H2020 program "ESTEEM3" (grant number 823717). A.V.P. thanks the Spanish Government (Agencia Estatal de Investigacion) and the European Union (European Regional Development Fund) for a grant for young researchers (CTQ2015-74138-JIN, AEI/FEDER/UE).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Sunlight-assisted hydrogenation of CO2 into ethanol and C2+ hydrocarbons by sodium-promoted Co@C nanocomposites

  • Liu, Lichen
  • Puga, Alberto V.
  • Cored-Bandrés, Jorge
  • Pérez-Dieste, Virginia
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • García Gómez, Hermenegildo|||0000-0002-9664-493X
  • Corma Canós, Avelino|||0000-0002-2232-3527
[EN] The hydrogenation of CO2 into hydrocarbons promoted by the action of sunlight has been studied on Co nanoparticles covered by thin carbon layers. In particular, nearly 100% selectivity to hydrocarbons is obtained with increased selectivities towards C2 + hydrocarbons and alcohols (mainly ethanol) when using nanostructured materials comprising metallic cobalt nanoparticles, carbon layers, and sodium as promoter (NaCo@C). In the contrary, larger amount of CH4 and lower selectivity to C2 + hydrocarbons and alcohols were obtained in the conventional thermal catalytic process. When using Co@C nanoparticles in the absence of Na or bare Co3O4 as catalyst, methane is essentially the main product (selectivity > 96%). Control experiments in the presence of methanol as a hole scavenger suggest the role of light in generating charges by photon absorption as promoting factor. The reaction mechanism for photoassisted CO2 hydrogenation on the Co-based catalysts was investigated by near ambient-pressure X-ray photoelectron (AP-XPS) and in situ Raman spectroscopies, which provided information on the role of light and Na promoter in the modulation of product distribution for CO2 hydrogenation. Spectroscopic studies suggested that surface CO2 dissociation to CO, the stabilization of CO adsorbed on the surface of Na-Co@C catalyst and the easy desorption of reaction products is a key step for photothermal CO2 hydrogenation to ethanol and C2 + hydrocarbons., L.L. thanks ITQ for providing a contract. A.V.P. thanks the Spanish Government (Agencia Estatal de Investigacion) and the European Union (European Regional Development Fund) for a grant for young researchers (CTQ2015-74138-JIN, AEI/FEDER/UE). J.C. thanks the Spanish Government-MINECO for a "Severo Ochoa" grant (BES-2015-075748). The AP-XPS experiments were performed at NAPP endstation of CIRCE beamline at ALBA Synchrotron with the collaboration of ALBA staff. The authors also thank the Microscopy Service of UPV for kind help on FESEM, TEM and STEM measurements. Financial supports from the Spanish Government-MINECO through "Severo Ochoa" (SEV-2016-0683) program are also gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Light-Promoted Hydrogenation of Carbon Dioxide¿An Overview

  • Puga Vaca, Alberto
[EN] Hydrogenation of carbon dioxide is considered as a viable strategy to generate fuels while closing the carbon cycle (heavily disrupted by the abuse in the exploitation of fossil resources) and reducing greenhouse gas emissions. The process can be performed by heat-powered catalytic processes, albeit conversion and selectivity tend to be reduced at increasing temperatures owing to thermodynamic constraints. Recent investigations, as summarised in this overview, have proven that light activation is a distinct possibility for the promotion of CO2 hydrogenation to fuels. This effect is particularly beneficial in methanation processes, which can be enhanced under simulated solar irradiation using materials based on metallic nanoparticles as catalysts. The use of nickel, ruthenium and rhodium has led to substantial efficiencies. Light-promoted processes entail performances on a par with (or even superior to) those of thermally-induced, industrially-relevant, commercial technologies., The author thanks the Spanish Government (Ministerio de Economía y Competitividad, MINECO) for financial support via a project for young researchers (CTQ2015-74138-JIN), and the ‘‘Severo Ochoa’’ programme (SEV 2012-0267). The European Union is also acknowledged for the SynCatMatch project (ERCAdG-2014-671093)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydrogenation of CO2 on Nickel-Iron Nanoparticles Under Sunlight Irradiation

  • Puga, Alberto V.
  • Corma Canós, Avelino|||0000-0002-2232-3527
[EN] Nickel-iron oxide nanoparticles were prepared by a simple mixed oxalate precursor decomposition method and used as catalysts for the sunlight-promoted CO2 hydrogenation reaction. The composition of the NiyFe1-yOx materials was designed to cover the entire Ni/Fe ratio range (y=1, 0.9, 0.75, 0.5, 0.25, 0.1, 0). Characterisation was undertaken by means of elemental analyses, X-ray diffraction and high resolution transmission electron microscopy. The pure nickel material (NiOx) contained crystalline NiO nanoparticles. Upon introducing lower proportions of iron in Ni9FeOx and Ni3FeOx, NiO was the only crystalline phase, along with increasing amounts of amorphous iron oxides. Higher iron contents resulted in the co-existence of NiO and -Fe2O3 domains at the nanoscale in NiFeOx, NiFe3Ox and NiFe9Ox, whereas the pure iron material (FeOx) was composed of -Fe2O3 as the only crystalline phase and a significant fraction of amorphous iron oxides. The hydrogenation of carbon dioxide was tested on the materials under simulated sunlight irradiation, and the activities and selectivities investigated as initial CO2 conversion rates and product distributions, respectively. The introduction of iron was beneficial for the activation of CO2, due to the known ability of this metal for promoting the reverse water-gas shift (rWGS) reaction. On the other hand, it was proven that nickel and iron favoured hydrogenation and chain growth processes, respectively. Moreover, the lack of hydrogenation sites in the pure iron material results in the expected preferential generation of olefins. Results for the entire compositional range draw a clear trend towards the enhanced formation of short-chain alkanes at middle iron contents, most likely owing to the existence of junctions between nickel and iron oxides at the nanoscale, and the related interfaces providing rWGS, chain growth and hydrogenation sites in close vicinity. The resulting hydrocarbon products, presumably produced by the efficient combination of thermal and photonic effects, can be considered as solar fuel replacements for natural gas and liquefied petroleum gases., Financial support from the Spanish Government-MINECO [Ministerio de Economia, Industria y Competitividad, Gobierno de Espana (ES)] through "Severo Ochoa" (SEV 2016-0683) is acknowledged. AVP also thanks the Spanish Government (Agencia Estatal de Investigacion) [Ministerio de Economia, Industria y Competitividad, Gobierno de Espana (ES)] and the European Union (European Regional Development Fund) for a grant for young researchers (CTQ2015-74138-JIN, AEI/FEDER/UE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessment of photocatalytic hydrogen production from biomass or wastewaters depending on the metal Co-Catalyst and its deposition method on TiO2

  • Imizcoz, Mikel
  • Puga, Alberto V.
© 2019 by the authors., A systematic study on the solar photocatalytic hydrogen production (photoreforming) performance of M/TiO2 (M = Au, Ag, Cu or Pt) using glucose as a model substrate, and further extended to lignocellulose hydrolysates and wastewaters, is herein presented. Three metal (M) co-catalyst loading methods were tested. Variation of the type of metal results in significantly dissimilar H2 production rates, albeit the loading method exerts an even greater effect in most cases. Deposition-precipitation (followed by hydrogenation) or photodeposition provided better results than classical impregnation (followed by calcination). Interestingly, copper as a co-catalyst performed satisfactorily as compared to Au, and slightly below Pt, thus representing a realistic inexpensive alternative to noble metals. Hydrolysates of either α-cellulose or rice husks, obtained under mild conditions (short thermal cycles at 160 °C), were rich in saccharides and thus suitable as feedstocks. Nonetheless, the presence of inhibiting byproducts hindered H2 production. A novel photocatalytic UV pre-treatment method was successful to initially remove the most recalcitrant portion of these minor products along with H2 production (17 µmol gcat−1 h−1 on Cu/TiO2). After a short UV step, simulated sunlight photoreforming was orders of magnitude more efficient than without the pre-treatment. Hydrogen production was also directly tested on two different wastewater streams, that is, a municipal influent and samples from operations in a fruit juice producing plant, with remarkable results obtained for the latter (up to 115 µmol gcat−1 h−1 using Au/TiO2)., Financial support from the Spanish Government (Ministry of Science, Innovation and Universities) through its “Severo Ochoa” excellence program (SEV 2016-0683), and to the Spanish Government (Agencia Estatal de Investigación) and the European Union (European Regional Development Fund) via a grant for young researchers (CTQ2015-74138-JIN, AEI/FEDER/UE), is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Determination of the evolution of heterogeneous single metal atoms and nanoclusters under reaction conditions: Which are the working catalytic sites?

  • Liu, Lichen
  • Meira, Debora M.
  • Arenal, Raúl
  • Concepción, Patricia
  • Puga, Alberto V.
  • Corma, Avelino
Identification of active sites in heterogeneous metal catalysts is critical for understanding the reaction mechanism at the molecular level and for designing more efficient catalysts. Because of their structural flexibility, subnanometric metal catalysts, including single atoms and clusters with a few atoms, can exhibit dynamic structural evolution when interacting with substrate molecules, making it difficult to determine the catalytically active sites. In this work, Pt catalysts containing selected types of Pt entities (from single atoms to clusters and nanoparticles) have been prepared, and their evolution has been followed, while they were reacting in a variety of heterogeneous catalytic reactions, including selective hydrogenation reactions, CO oxidation, dehydrogenation of propane, and photocatalytic H2 evolution reaction. By in situ X-ray absorption spectroscopy, in situ IR spectroscopy, and high-resolution electron microscopy techniques, we will show that some characterization techniques carried out in an inadequate way can introduce confusion on the interpretation of coordination environment of highly dispersed Pt species. Finally, the combination of catalytic reactivity and in situ characterization techniques shows that, depending on the catalyst–reactant interaction and metal–support interaction, singly dispersed metal atoms can rapidly evolve into metal clusters or nanoparticles, being the working active sites for those abovementioned heterogeneous reactions., This work has been supported by the European Union through the European Research Council (grant ERC-AdG-2014-671093, SynCatMatch) and the Spanish government through the “Severo Ochoa Program” (SEV-2016-0683). L.L. thanks ITQ for providing a contract. The authors also thank Microscopy Service of UPV for the TEM and STEM measurements. This research used resources of the Advanced Photon Source, an Office of Science User Facility operated for the U.S. Department of Energy (DOE) Office of Science by Argonne National Laboratory, and was supported by the U.S. DOE under contract no. DE-AC02-06CH11357 and the Canadian Light Source and its funding partners. The HR STEM and STEM–EELS studies were conducted at the Laboratorio de Microscopias Avanzadas, Universidad de Zaragoza, Spain. R.A. acknowledges support from Spanish MINECO grant MAT2016-79776-P (AEI/FEDER, UE), from the Government of Aragon and the European Social Fund (grant number E13_17R, FEDER, UE), and from the European Union H2020 program “ESTEEM3” (grant number 823717). A.V.P. thanks the Spanish Government (Agencia Estatal de Investigación) and the European Union (European Regional Development Fund) for a grant for young researchers (CTQ2015-74138-JIN, AEI/FEDER/UE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optimising hydrogen production: Via solar acetic acid photoreforming on Cu/TiO 2

  • Imizcoz, Mikel
  • Puga, Alberto V.
Valorisation of aqueous acetic acid - a model bio-oil component - by solar photocatalysis on Cu/TiO is efficient, yet decarboxylation tends to dominate over photoreforming due to copper co-catalyst oxidation. Selectivities to hydrogen were greatly enhanced by in situ photoreduction, ensuring the removal of passivation layers to unmask active Cu(0) surfaces, in a reversible fashion., Financial support from the Spanish Government (Ministry of Science, Innovation and Universities) through its “Severo Ochoa” excellence programme (SEV 2016-0683) is acknowledged. A. V. P. thanks the Spanish Government (Agencia Estatal de Investigación) and the European Union (European Regional Development Fund) for a grant for young researchers (CTQ2015-74138-JIN, AEI/FEDER/UE). M. I. thanks the Spanish Catalysis Society (SECAT) for a Masters Grant. The authors also thank the Microscopy Service of UPV for kind help on TEM measurements.