Pasar al contenido principal

PRODUCCION SOSTENIBLE DE NANOCELULOSAS PARA SU APLICACION EN DIFERENTES SECTORES Y PROCESOS INDUSTRIALES

CTQ2017-85654-C2-2-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD COMPLUTENSE DE MADRID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

Docta Complutense
Publicación Artículo científico (JournalArticle)

Ni(II) and Pb(II) Removal Using Bacterial Cellulose Membranes

  • Ojembarrena Jiménez, Francisco De Borja
  • García, Sergio
  • Merayo, Noemi
  • Blanco Suárez, María Ángeles
  • Negro Álvarez, Carlos Manuel
Bacterial cellulose (BC) is a highly crystalline nanosized material with a high number of active groups. This study focuses on the synthesis of BC membranes through fermentation, their characterization and application to remove Ni(II) and Pb(II) from wastewater by adsorption under different conditions. Four-day-grown BC membranes form three-dimensional nanofibril networks with a pH of 6.3 and a high cationic demand (52.5 μeq·g−1). The pseudo-second-order kinetic model and the Sips isotherm model best describe the adsorption of both metals. The intraparticle diffusion model of Ni(II) revealed a three-step mechanism of adsorption-plateau-adsorption, while Pb(II) adsorption followed a typical reducing-slope trend up to saturation. The highest removal of Ni(II) and Pb(II) was obtained at pH 4 with a BC dosage of 400 mg·L−1. The maximum adsorption capacities were 28.18 mg·g−1 and 8.49 mg·g−1 for Ni(II) and Pb(II), respectively, involving the total coverage of the material active sites. Thermodynamically, Ni(II) adsorption was exothermic, and Pb(II) was endothermic. The obtained values of sorption heat, activation and Gibbs’ energy depicted a physisorption process. Ni(II) removal mechanism was ruled by crystallization on the metals adsorbed on the BC active groups, while Pb(II) was driven by the adsorption process, as shown by TEM images of the spent material.</jats:p>
Docta Complutense
Publicación Artículo científico (JournalArticle)

Cellulose nanofibers and chitosan to remove flexographic inks from wastewaters

  • Balea Martín, Ana
  • Monte Lara, María Concepción
  • Fuente González, Elena de la
  • Negro Álvarez, Carlos Manuel
  • Sánchez Salvador, José Luis
  • Blanco Suárez, María Ángeles
Flexographic printing technology is an economical, productive, low maintenance and versatile technology. However, the removal of these inks by the traditional flotation process during paper recycling is not possible since they remain dissolved in the waters, making necessary the development of alternative methods. Recent studies have revealed the potential use of nanocellulose (NC) combined with a cationic polyacrylamide to remove flexographic inks from wastewater. The use of a natural polymer, such as chitosan, would be an important improvement of this treatment because NC and chitosan are the two most abundant natural polymers with interesting properties, such as non-toxicity and biodegradability. Therefore, in this study the decolorization of three flexographic inks (copper phthalocyanine blue, carbon black and diarylide yellow) by the sequential addition of cellulose nanofibers, produced from recycled paper, and chitosan has been evaluated. Results show that this eco-friendly approach has high potential for the removal of water-based inks with an almost 100% reduction of turbidity and ink from the wastewater. Moreover, the final sludge containing nanocellulose and inks could be used to reinforce the pulp of the middle layers of carton board, improving the mechanical properties of the product and reducing waste generation.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Chitosan grafted/cross-linked with biodegradable polymers: a review

  • Sánchez Salvador, José Luis
  • Balea Martín, Ana
  • Monte Lara, María Concepción
  • Negro Álvarez, Carlos Manuel
  • Blanco Suárez, María Ángeles
Public perception of polymers has been drastically changed with the improved plastic management at the end of their life. However, it is widely recognised the need of developing biodegradable polymers, as an alternative to traditional petrochemical polymers. Chitosan (CH), a biodegradable biopolymer with excellent physiological and structural properties, together with its immunostimulatory and antibacterial activity, is a good candidate to replace other polymers, mainly in biomedical applications. However, CH has also several drawbacks, which can be solved by chemical modifications to improve some of its characteristics such as solubility, biological activity, and mechanical properties. Many chemical modifications have been studied in the last decade to improve the properties of CH. This review focussed on a critical analysis of the state of the art of chemical modifications by cross-linking and graft polymerization, between CH or CH derivatives and other biodegradable polymers (polysaccharides or proteins, obtained from microorganisms, synthetized from biomonomers, or from petrochemical products). Both techniques offer the option of including a wide variety of functional groups into the CH chain. Thus, enhanced and new properties can be obtained in accordance with the requirements for different applications, such as the release of drugs, the improvement of antimicrobial properties of fabrics, the removal of dyes, or as scaffolds to develop bone tissues.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Critical comparison of the properties of cellulose nanofibers produced from softwood and hardwood through enzymatic, chemical and mechanical processes

  • Sánchez-Salvador, José Luis
  • Campano, Cristina
  • Balea, Ana
  • Tarrés, Quim
  • Delgado-Aguilar, Marc
  • Mutjé, Pere
  • Blanco, Angeles
  • Negro, Carlos
10 p.-10 fig., Current knowledge on the properties of different types of cellulose nanofibers (CNFs) is fragmented. Properties variation is very extensive, depending on raw materials, effectiveness of the treatments to extract the cellulose fraction from the lignocellulosic biomass, pretreatments to facilitate cellulose fibrillation and final mechanical process to separate the microfibrils. Literature offers multiple parameters to characterize the CNFs prepared by different routes. However, there is a lack of an extensive guide to compare the CNFs. In this study, we perform a critical comparison of rheological, compositional, and morphological features of CNFs, produced from the most representative types of woody plants, hardwood and softwood, using different types and intensities of pretreatments, including enzymatic, chemical and mechanical ones, and varying the severity of mechanical treatment focusing on the relationship between macroscopic and microscopic parameters. This structured information will be exceedingly useful to select the most appropriate CNF for a certain application based on the most relevant parameters in each case., Authors want to acknowledge the Spanish Ministry of Economy and Competitiveness for the funding of the projects CTQ2017-85654-C2-1-R and CTQ2017-85654-C2-2-R, the Spanish Ministry of Science and Innovation (PDC2021-120964-C21 and PDC2021-120964-C22), the Community of Madrid for funding the RETO-PROSOST-2-CM (P2018/EMT4459), as well as the support of Universidad Complutense de Madrid and Banco de Santander for the grant of J.L. Sanchez-Salvador (CT17/17). Thanks also to Spanish Ministry of Science and Innovation for the Juan de la Cierva aid of Cristina Campano (Ref. FJC2019-040298-I)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanocrystalline Cellulose to Reduce Superplasticizer Demand in 3D Printing of Cementitious Materials

  • Jarabo, Rocío
  • Fuente, Elena
  • García Calvo, José Luis
  • Carballosa, Pedro
  • Negro, Carlos
One challenge for 3D printing is that the mortar must flow easily through the printer nozzle, and after printing, it must develop compressive strength fast and high enough to support the layers on it. This requires an exact and difficult control of the superplasticizer (SP) dosing. Nanocrystalline cellulose (CNC) has gained significant interest as a rheological modifier of mortar by interacting with the various cement components. This research studied the potential of nanocrystalline cellulose (CNC) as a mortar aid for 3D printing and its interactions with SPs. Interactions of a CNC and SP with cement suspensions were investigated by means of monitoring the effect on cement dispersion (by monitoring the particle chord length distributions in real time) and their impact on mortar mechanical properties. Although cement dispersion was increased by both CNC and SP, only CNC prevented cement agglomeration when shearing was reduced. Furthermore, combining SP and CNC led to faster development of compressive strength and increased compressive strength up to 30% compared to mortar that had undergone a one-day curing process., This research was funded by CDTI, grant number SNEO-20181016 (NEOTEC program), and by the Economy and Competitiveness Ministry of Spain, grant numbers: CTQ2017-85654-C2-1-R and CTQ2017-85654-C2-2-R., Peer reviewed
Docta Complutense
Publicación Artículo científico (JournalArticle)

A reproducible method to characterize the bulk morphology of cellulose nanocrystals and nanofibers by transmission electron microscopy

  • Campano, Cristina
  • Balea Martín, Ana
  • Blanco Suárez, María Ángeles
  • Negro Álvarez, Carlos Manuel
With the increased use of nanocelluloses as additives in many industrial applications, better characterization methods are needed to ensure their effectiveness. Transmission electron microscopy (TEM) is an appropriate image acquisition system to enable their morphological characterization. The use of TEM has typically been focused on determining the diameter and length of individual cellulose nanocrystals (CNCs) or nanofibers (CNFs), so different dispersion practices, such as sonication or the use of dispersants, are commonly applied to separate the particles. However, this study aims to improve the characterization of the bulk morphology of CNCs and CNFs by TEM, taking steps towards the determination of the aggregation/dispersion degree as well as the fibrillation degree of CNFs. TEM has been investigated with two types of grids (holey and Formvar/carbon), three different fixing methods (Poly-l-Lysine, glow discharge and UV radiation) and the use of negative staining. Fractal dimension and lacunarity were used to quantify the reproducibility of the improved method. With the use of Poly-l-Lysine, the attachment of CNCs and CNFs particles on the TEM grids was ensured, due to the electrostatic interactions between negatively charged nanocelluloses and positively charged and hydrophilic Poly-l-Lysine surfaces. The low value of lacunarity, close to 0.3, shows a very high reproducibility of the methodology proposed. With this new approach, the state that the nanocelluloses have in suspension can be directly characterized by TEM.