Pasar al contenido principal

LOW INTENSITY ULTRASOUNDS FOR EARLY DETECTION AND MODULATION OF TUMOR AND STROMA

DPI2017-90147-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 19
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación

A label free disposable device for rapid Isolation of rare tumor cells from blood by ultrasounds

  • González, Itziar
  • Earl, Julie
  • Fernández Ledesma, Luis Javier
  • Sainz, Bruno Jr.
  • Pinto, Alberto
  • Monge, Rosa
  • Alcalá, Sonia
  • Castillejo, Adela
  • Soto, José Luis
  • Carrato, Alfredo
This article belongs to the Special Issue Microfluidics for Circulating Biomarkers., The use of blood samples as liquid biopsy is a label-free method for cancer diagnosis that offers benefits over traditional invasive biopsy techniques. Cell sorting by acoustic waves offers a means to separate rare cells from blood samples based on their physical properties in a label-free, contactless and biocompatible manner. Herein, we describe a flow-through separation approach that provides an efficient separation of tumor cells (TCs) from white blood cells (WBCs) in a microfluidic device, “THINUS-Chip” (Thin-Ultrasonic-Separator-Chip), actuated by ultrasounds. We introduce for the first time the concept of plate acoustic waves (PAW) applied to acoustophoresis as a new strategy. It lies in the geometrical chip design: different to other microseparators based on either bulk acoustic waves (BAW) or surface waves (SAW, SSAW and tSAW), it allows the use of polymeric materials without restrictions in the frequency of work. We demonstrate its ability to perform high-throughput isolation of TCs from WBCs, allowing a recovery rate of 84% ± 8% of TCs with a purity higher than 80% and combined viability of 85% at a flow rate of 80 μL/min (4.8 mL/h). The THINUS-Chip performs cell fractionation with low-cost manufacturing processes, opening the door to possible easy printing fabrication., This work was partially supported by the Ministry of Economy and Competence of Spain (MINECO) under two projects: BIO2011-30535-C04-01: Development of a high-throughput ultrasonic technology for the isolation of circulating tumor cells from peripheral blood samples; and DPI2017-90147-R: Low intensity a Low Intensity ultrasounds for early diagnosis and modulation of tumor and stroma.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and in vitro cytocompatibility of segmented poly(ester-urethane)s and poly(ester-urea-urethane)s for bone tissue engineering

  • González-García, Dulce María
  • Marcos-Fernández, Ángel
  • Rodríguez-Lorenzo, Luis M.
  • Jiménez-Gallegos, Rodrigo
  • Vargas-Becerril, Nancy
  • Téllez-Jurado, Lucía
Two series of segmented polyurethanes were obtained and their mechanical and thermal properties as well as their biodegradability and cytotoxicity were evaluated. The chemical nature of the polyurethanes was varied by using either 1,4 butanediol (poly-ester-urethanes, PEUs) or l-lysine ethyl ester dihydrochloride (poly-ester-urea-urethanes, PEUUs) as chain extenders. Results showed that varying the hard segment influenced the thermal and mechanical properties of the obtained polymers. PEUs showed strain and hardness values of about 10–20 MPa and 10–65 MPa, respectively. These values were higher than the obtained values for the PEUUs due to the phase segregation and the higher crystallinity observed for the polyester-urethanes (PEUs); phase segregation was also observed and analyzed by XRD and DSC. Moreover, both series of polymers showed hydrolytic degradation when they were submerged in PBS until 90 days with 20% of weight loss. In vitro tests using a Human Osteoblastic cell line (Hob) showed an average of 80% of cell viability and good adhesion for both series of polymers., This research was founded by CONACYT and DPI2017-90147-R from MINECO-AEI, Spain. Dulce María Gonzalez-Garcia thanks CONACYT for the fellowship and fund DPI 2017-90147-R from MINECO-AEI, Spain. The authors thank Mar Fernandez Gutierrez and Rosa Ana Ramirez Jimenez for helping with biological characterization and to the ICTP in Madrid for the technical assistance and residence., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nonuniform Bessel-Based Radiation Distributions on A Spherically Curved Boundary for Modeling the Acoustic Field of Focused Ultrasound Transducers

  • Gutierrez, Mario Ibrahin
  • Ramos, Antonio
  • Gutierrez, Josefina
  • Vera, Arturo
  • Leija, Lorenzo
Therapeutic focused ultrasound is a technique that can be used with different intensities depending on the application. For instance, low intensities are required in nonthermal therapies, such as drug delivering, gene therapy, etc.; high intensity ultrasound is used for either thermal therapy or instantaneous tissue destruction, for example, in oncologic therapy with hyperthermia and tumor ablation. When an adequate therapy planning is desired, the acoustic field models of curve radiators should be improved in terms of simplicity and congruence at the prefocal zone. Traditional ideal models using uniform vibration distributions usually do not produce adequate results for clamped unbacked curved radiators. In this paper, it is proposed the use of a Bessel-based nonuniform radiation distribution at the surface of a curved radiator to model the field produced by real focused transducers. This proposal is based on the observed complex vibration of curved transducers modified by Lamb waves, which have a non-negligible effect in the acoustic field. The use of Bessel-based functions to approximate the measured vibration instead of using plain measurements simplifies the rationale and expands the applicability of this modeling approach, for example, when the determination of the effects of ultrasound in tissues is required., This research was funded by CONACyT, grant number 257966; CSIC, grant number COOPB20166; ERAnet-EMHE CSIC, grant number 200022; Spanish P.N RETOS, grant number DPI2017-90147-R; and CYTED-Ditecrod Network Ref. 218RT0545., We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Alginate hydrogels for bone tissue engineering, from injectables to bioprinting: A Review

  • Hernández-González, Aurora C.
  • Téllez-Jurado, Lucía
  • Rodríguez-Lorenzo, Luis M.
This review focuses on recently developed alginate injectable hydrogels and alginate composites for applications in bone tissue regeneration, and it evaluates the alternatives to overcome the problems that avoid their utilization in the field. Section 2 covers the properties of alginates that have made them useful for medical applications, in particular their ionic gelling ability for preparing injectable compositions used as delivery drugs systems. The advantages and shortcomings of these preparations are revised together with the chemical modifications assayed. Section 3 describes how it has been taken advantage of alginates into the new field of biofabrication and the developments in bone engineering. The state of the art of this field is reviewed. Finally in section 4, new developments and approaches that in opinion of the authors can lead to a breakthrough in bone tissue engineering using alginates are introduced., Instituto Politécnico Nacional, Mexico (IPN-SIP 20196660), AEI/FEDER, UE (DPI2017-90147-R)., CONACYT scholarship, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Hybrid alginate-silica hydrogels for tissue engineering

  • Hernández-González, Aurora C.
  • Téllez-Jurado, Lucía
  • Rodríguez-Lorenzo, Luis M.
AEI/FEDER, UE (DPI2017-90147-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrasound Technology as a Novel Treatment Strategy in Pancreatic Cancer

  • González Gómez, Icíar
  • Ramos Fernández, Antonio
  • Rodríguez-Lorenzo, Luis M.
  • Pinto del Corral, Alberto
  • Hernández, Luis
  • Frutos Díaz-Alejo, Jesús
  • Pachón Olmos, Vanessa
  • Perna, Cristian
  • Earl, Julie
Adenocarcinoma of the pancreas (PDAC) accounts for 2.4% of all cancers diagnosed and is the fourth leading cause of cancer death, with almost equal rates of incidence and mortality [1]. By 2030, pancreatic cancer is projected to be the second leading cause of cancer-related death [2], surpassing breast, prostate and colorectal cancer. The overall survival at 5 years of around 7.2% as the majority of patients present with advanced disease at diagnosis. Patients with localized disease are treated with surgery, with or without neoadjuvant chemotherapy/ radiotherapy, followed by adjuvant chemotherapy. The majority (around 80%) of patients are treated only with chemotherapy as they have an advanced disease. Patients are treated in the first line with gemcitabine-abraxane or Folfirinox and with Naliri plus 5FU in the second line. There have been few clinical advances in PDAC treatment over the last 20 years and chemotherapy is the only treatment option available for the majority of patients. These tumours are also resistant to many targeted therapies such as anti-EGFR therapy like cetuximab [3] due to the presence of a KRAS mutation in the majority of primary tumors. Personalized medicine strategies have not yet been established in pancreatic cancer as in other more common tumour types. Thus, novel anti-tumour strategies are an important clinical need in order to improve survival rates., AEI/FEDER, UE DPI 2017-90147-R., Intramural call for new research projects for clinical researchers and emerging research groups. IRYCIS. (2018/0240), Iberoamerican Network CYTED-DITECROD-218RT0545., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Design of Thermoplastic 3D-Printed Scaffolds for Bone Tissue Engineering: Influence of Parameters of “Hidden” Importance in the Physical Properties of Scaffolds

  • Cubo-Mateo, Nieves
  • Rodríguez-Lorenzo, Luis M.
Additive manufacturing (AM) techniques are becoming the approaches of choice for the construction of scaffolds in tissue engineering. However, the development of 3D printing in this field brings unique challenges, which must be accounted for in the design of experiments. The common printing process parameters must be considered as important factors in the design and quality of final 3D-printed products. In this work, we study the influence of some parameters in the design and fabrication of PCL scaffolds, such as the number and orientation of layers, but also others of “hidden” importance, such as the cooling down rate while printing, or the position of the starting point in each layer. These factors can have an important impact oin the final porosity and mechanical performance of the scaffolds. A pure polycaprolactone filament was used. Three different configurations were selected for the design of the internal structure of the scaffolds: a solid one with alternate layers (solid) (0 , 90 ), a porous one with 30% infill and alternate layers (ALT) (0 , 90 ) and a non-alternated configuration consisting in printing three piled layers before changing the orientation (n-ALT) (0 , 0 , 0 , 90 , 90 , 90 ). The nozzle temperature was set to 172 C for printing and the build plate to 40 C. Strand diameters of 361 26 m for room temperature cooling down and of 290 30 m for forced cooling down, were obtained. A compression elastic modulus of 2.12 0.31 MPa for n-ALT and 8.58 0.14 MPa for ALT sca olds were obtained. The cooling down rate has been observed as an important parameter for the final characteristics of the scaffold., AEI/FEDER, UE project: DPI2017-90147-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Hydrodynamics and Hematocrit on Ultrasound-Induced Blood Plasmapheresis

  • González, Itziar
  • Andrés, Roque Rubén
  • Pinto, Alberto
  • Carreras, Pilar
© 2020 by the authors, Acoustophoretic blood plasma separation is based on cell enrichment processes driven by acoustic radiation forces. The combined influence of hematocrit and hydrodynamics has not yet been quantified in the literature for these processes acoustically induced on blood. In this paper, we present an experimental study of blood samples exposed to ultrasonic standing waves at different hematocrit percentages and hydrodynamic conditions, in order to enlighten their individual influence on the acoustic response of the samples. The experiments were performed in a glass capillary (700 µm-square cross section) actuated by a piezoelectric ceramic at a frequency of 1.153 MHz, hosting 2D orthogonal half-wavelength resonances transverse to the channel length, with a single-pressure-node along its central axis. Different hematocrit percentages Hct = 2.25%, 4.50%, 9.00%, and 22.50%, were tested at eight flow rate conditions of Q = 0:80 µL/min. Cells were collected along the central axis driven by the acoustic radiation force, releasing plasma progressively free of cells. The study shows an optimal performance in a flow rate interval between 20 and 80 µL/min for low hematocrit percentages Hct ≤ 9.0%, which required very short times close to 10 s to achieve cell-free plasma in percentages over 90%. This study opens new lines for low-cost personalized blood diagnosis., This research was funded by the Spanish Government, grant no. DPI2017-90147-R and European Commission H2020 MSCA-IF-GF 705163., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

SYNTHESIS OF IN-SITU SILICA-ALGINATE HYBRID HYDROGELS BY A SOLGEL ROUTE

  • Hernández-González, Aurora C.
  • Téllez-Jurado, Lucía
  • Rodríguez-Lorenzo, Luis M.
The preparation of silica-alginate hybrid hydrogels by a sol-gel route is proposed in this work. The in-situ synthesis of silica networks from tetraethoxysilane (TEOS) and aminopropyltriethoxysilane (APTES) precursors in an alginate matrix is assayed. The experimental parameters were analyzed in three consecutive stages to obtain hybrid materials with specific properties. Stage 1: effect of water and catalyst ratios. Stage 2: effect of the inorganic precursor’s ratio. Stage 3: effect of concentration of the alginate solution. The hydrolysis-condensation reactions of the silica precursors were regulated by the alginate concentration, the silica precursor nature, and the HCl/inorganic/H2O ratio. Hybrids prepared with both silica precursors generate longer silica chains. High alginate amounts increase the storage modulus of synthesized hybrids, and high catalyst ratios reduce their stability. Compositions with alginate content of 5 and 8 (wt/v)%, TEOS/APTES weight ratio of 74/26, and without catalyst are suitable to evaluation for their application in tissue engineering., Instituto Politécnico Nacional,México (IPN-SIP 20196660 and IPN-SIP 20201294).AEI/FEDER, UE (DPI2017-90147-R). Financial support from CONACYT scholarship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

DISEÑO Y DESARROLLO DE NUEVAS BIOTINTAS Y ESTRATEGIAS DE BIOIMPRESIÓN PARA PRODUCIR EQUIVALENTES SIMPLIFICADOS DE TEJIDOS HUMANOS PARA SU USO EN LA TIERRA Y EN MISIONES EXPLORATORIAS ESPACIALES, DESIGN AND DEVELOPMENT OF NEW BIOINKS AND BIOPRINTING STRATEGIES TO PRODUCE SIMPLIFIED EQUIVALENTS OF HUMAN TISSUES, FOR EARTH AND SPACE EXPLORATION APPLICATIONS

  • Cubo-Mateo, Nieves
[EN] Fifty years after the first human landed on the Moon mankind has started to plan the next steps for manned space exploration missions. When the time required to return to Earth exceeds 400-500 days (as in travels to Mars), the level of independence that the crew must possess is highly increased. To ensure the survival and good living conditions of this future explorers, new developments regarding medical infrastructure and resources must be carried out. In this work, the topic of this study was to investigate how 3D printing and bioprinting can be of use to improve the autonomy of the crew when facing the most probable clinical scenarios that can occur in long-term space exploratory missions. The printing parameters of thermoplastics, such as polycaprolactone (PCL), that can be used as a possible support material along bioprinting were studied, including the use or not of alternate layers or the printing starting point. For bioprinting, and taking bone constructs as the tissue of study, a new bioink based on human plasma (which potentially could be derived from the injured astronaut who needs the treatment), alginate, and methylcellulose (that can be grow and used in isolated areas) was designed. An inverted bioprinter was designed and built to be able to test the work capacity of this biomaterial in altered gravity conditions. As result, it was observed that the use of alternated layers involves the generation of more anisotropic structures, as the z-axis pore is limited to the layer height, while the x and y-pore size can be tailored to specific needs. The defects created because of the alignment, or the lack of it, at the new layer starting point, significantly affects the mechanical behavior of the scaffolds. ix The cooling down rate, or even printing speed, can be modified to obtain more chaotic micropatterns including nanofibers without the need of using further technologies. A plasma-based bioink was successfully designed and combined with hydroxyapatite-forming CPC which resembles the native mineral phase of bone. The results have shown that the plasma-based bioink and CPC form a synergistic system supporting adhesion, proliferation, and osteogenic differentiation of bone cells. Thanks to the inverted bioprinter, it has been demonstrated that the developed bioinks and support materials, like CPC, are suitable for extrusion (bio)printing. They are so adhesive that they can even be printed upside-down and therefore, against Earth’s gravity. Therefore, they could be used at altered gravity conditions on space exploration missions., [ES] Cincuenta años después de que el primer ser humano aterrizara en la Luna, la humanidad ha comenzado a planificar los próximos pasos para las misiones de exploración espacial tripuladas. Cuando el tiempo necesario para regresar a la Tierra supera los 400 - 500 días (como en los viajes a Marte), el nivel de independencia que debe poseer la tripulación aumenta considerablemente. Para garantizar la supervivencia y las buenas condiciones de vida de estos futuros exploradores, se deben realizar nuevos desarrollos en cuanto a infraestructuras y recursos médicos. En este trabajo, se estudió cómo la impresión 3D y la bioimpresión pueden ser de utilidad para mejorar la autonomía de la tripulación ante los escenarios clínicos más probables que pueden ocurrir en misiones de larga duración. Para ello se estudiaron algunos parámetros de impresión de termoplásticos, como la policaprolactona (PCL), que pueden utilizarse x como posible material de soporte a lo largo de la bioimpresión (ejemplo de parámetros: uso o no de capas alternas o la alineación del punto de partida de la impresión en cada capa). Para la bioimpresión, y tomando las construcciones óseas como tejido de estudio, se diseñó un nuevo material compuesto a base de plasma humano (que puede ser obtenido de los astronautas), alginato y metilcelulosa (que se puede obtener y utilizar en áreas aisladas). Se diseñó y construyó una bioimpresora invertida para poder probar la capacidad de trabajo de este biomaterial en condiciones de gravedad alterada. Como resultado se obtuvo que el uso de capas alternas implica la generación de más estructuras anisotrópicas, ya que normalmente el poro del eje z está limitado a la altura de la capa, mientras que el tamaño de los poros x e y se pueden adaptar a necesidades especıificas. Los defectos creados por la alineación, o la falta de ella, en el punto de inicio de la nueva capa, afectan significativamente al comportamiento mecánico de los andamios. La velocidad de enfriamiento, o incluso la velocidad de impresión, se puede modificar para obtener micropatrones más caóticos, incluso nanofibras, sin necesidad de utilizar tecnologías adicionales. Se diseñó con éxito una biotinta a base de plasma y se combinó con un cemento de fosfato cálcico formador de hidroxiapatita, que se asemeja al mineral nativo del hueso. Nuestros resultados mostraron que la deposición combinada de la biotinta basada en plasma y la pasta de CPC para dar lugar a constructos celularizados, forman un sistema sinérgico que apoya la adhesión, la proliferación y la diferenciación osteogénica de las células óseas. Gracias a la bioimpresora invertida desarrollada, se ha podido demostrar que la biotinta desarrollada y los materiales de soporte, como el cemento óseo de fosfato cálcico autoajustable, son aptos para la (bio)impresión extrusión. Son tan adhesivos que incluso se pueden imprimir al revés y, por lo tanto, contra la gravedad de la Tierra, pudiendo usarse en condiciones de gravedad alterada., DAAD Research Grant. Program: Short-Term Grants, 2018 (57378443). – Project "3D Printing of Living Tissue for Space Exploration" funded from the European Space Agency (ESA). Funds came them partially by the University of Dresden via a contract (No. 4000123640/17/NL/BJ/gp/TUD) of OHB System AG, Bremen and by OHB System AG itself, under a contract of the European Space Agency ESA (contract No. 4000123640/18/NL/BJ/gp). – "Low intensity ultrasounds for early detection and modulation of tumour and stroma". Convocatoria Proyecto Retos I+D+i 2017. AEI/FEDER: DPI2017-90147-R. Entidad financiadora: Agencia Estatal de Investigación, Ministerio de Economía, Industria y Competitividad, Gobierno de España., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis de maestría (MasterThesis)

PREPARACIÓN Y PROPIEDADES REOLÓGICAS DE MACROMOLÉCULAS DE POLICAPROLACTONA-IMIDAZOL

  • Pérez, Luis Andrés
The goal of this project is the synthesis and characterization of a polyurethane made of soft segments of polycaprolactone (PCL) and hard segments of hexamethylen isocyanate (HDI), 1,3-di (2-hydroxyetil) imidazolium (IMI) or 1,4-butanediol (BT). Obtained polymers have been characterized by 1H –NMR and GPC and the effect of the introduction of the hard segments in the thermal and mechanical properties evaluated. IMI and BT have been successfully incorporated into the PCL backbone. The soft segment has maintained the capacity to crystallize. Melting point of the obtained compounds is lower than melting point of PCL favoring the processability. The wettability is improved in comparison with the PCL as well. The compound with a lower ratio of hard segment also improved thermal stability. Variations in the fluency point and Young modulus have not been observed, Los polímeros obtenidos se han caracterizado fundamentalmente por 1H-RMN, IR-ATR y HPLC. Por otro lado, se ha medido la influencia de la incorporación de los segmentos duros de HDI-IMI o HDI-BD en las propiedades térmicas y mecánicas. En las muestras sintetizadas las muestras con segmento blando de PCL ha mantenido su capacidad de cristalización, además de producirse un ligero aumento de hidrofilia y una disminución en el punto de fusión de la PCL, lo que mejora su procesabilidad. Se ha observado también como con la incorporación del segmento duro de HDI-IMI se obtiene una mejora en su estabilidad térmica con respecto a su homónima de HDI-BD. En cuanto a las propiedades mecánicas, no se ha observado una gran variación en el punto de fluencia ni en el módulo de Young., AEI/FEDER,UE (DPI2017-90147-R, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis of in situ silica-alginate hybrid hydrogels by a sol-gel route

  • Hernández-González, Aurora C.
  • Téllez-Jurado, Lucía
  • Rodríguez-Lorenzo, Luis M.
The preparation of silica-alginate hybrid hydrogels by a sol-gel route is proposed in this work. The in-situ synthesis of silica networks from tetraethoxysilane (TEOS) and aminopropyltriethoxysilane (APTES) precursors in an alginate matrix is assayed. The experimental parameters were analyzed in three consecutive stages to obtain hybrid materials with specific properties. Stage 1: effect of water and catalyst ratios. Stage 2: effect of the inorganic precursor¿s ratio. Stage 3: effect of concentration of the alginate solution. The hydrolysis-condensation reactions of the silica precursors were regulated by the alginate concentration, the silica precursor nature, and the HCl/inorganic/H2O ratio. Hybrids prepared with both silica precursors generate longer silica chains. High alginate amounts increase the storage modulus of synthesized hybrids, and high catalyst ratios reduce their stability. Compositions with alginate content of 5 and 8 (wt/v)%, TEOS/APTES weight ratio of 74/26, and without catalyst are suitable to evaluation for their application in tissue engineering, This work was supported by Instituto Politécnico Nacional,México (IPN-SIP 20196660 and IPN-SIP 20201294), and AEI/FEDER,UE (DPI2017-90147-R). Financial support from CONACYT scholarshipis acknowledged
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessment of a PCL-3D Printing-Dental Pulp Stem Cells Triplet for Bone Engineering: An In Vitro Study

  • Raúl Rosales-Ibáñez, Nieves Cubo-Mateo, Amairany Rodríguez-Navarrete, Arely M González-González, Tomás E Villamar-Duque, Leticia O Flores-Sánchez, Luis M Rodríguez-Lorenzo
The search of suitable combinations of stem cells, biomaterials and scaffolds manufacturing methods have become a major focus of research for bone engineering. The aim of this study was to test the potential of dental pulp stem cells to attach, proliferate, mineralize and differentiate on 3D printed polycaprolactone (PCL) scaffolds. A 100% pure Mw: 84,500 +- 1000 PCL was selected. 5 x 10 x 5 mm3 parallelepiped scaffolds were designed as a wood-pilled structure composed of 20 layers of 250 microm in height, in a non-alternate order ([0,0,0,90,90,90º]). 3D printing was made at 170 ºC. Swine dental pulp stem cells (DPSCs) were extracted from lower lateral incisors of swine and cultivated until the cells reached 80% confluence. The third passage was used for seeding on the scaffolds. Phenotype of cells was determined by flow Cytometry. Live and dead, Alamar blue™, von Kossa and alizarin red staining assays were performed. Scaffolds with 290 + 30 micron strand diameter, 938 x 80 micron pores in the axial direction and 689 x 13 micron pores in the lateral direction were manufactured. Together, cell viability tests, von Kossa and Alizarin red staining indicate the ability of the printed scaffolds to support DPSCs attachment, proliferation and enable differentiation followed by mineralization. The selected material-processing technique-cell line (PCL-3D printing-DPSCs) triplet can be though to be used for further modelling and preclinical experiments in bone engineering studies., Grant PAPIIT IA207420, UNAM, México and AEI/FEDER, UE (DPI2017-90147-R) Spain., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

PREPARATION OF COVALENTLY BONDED SILICA-ALGINATE HYBRID HYDROGELS BY SCHIFF BASE AND SOL-GEL REACTIONS

  • Hernández-González, Aurora C.
  • Téllez-Jurado, Lucía
  • Rodríguez-Lorenzo, Luis M.
Organic-inorganic hybrid materials overcome drawbacks associated with alginate hydrogels. In this work, covalently coupled silica-alginate hybrids were prepared by Schiff base formation and sol-gel reaction using alginate dialdehyde (ADA), (3- Aminopropyl) triethoxysilane (APTES), and APTES/tetraethylorthosilicate (TEOS) precursors. The influence of the polysaccharide/inorganic ratio, the nature of the inorganic precursor and the ionic crosslinking ability are studied. Prepared hybrids were characterized by FT-IR, 13C and 29Si -NMR spectroscopies, SEM, and rheology. For ADA/APTES hybrids, at higher ADA content, Schiff base formation is predominant, but at lower ADA content, the sol-gel reaction is prevalent. However, the progress of the sol-gel reactions for ADA/(APTES+TEOS), is favored with higher ADA compositions. Introducing a posterior ionic crosslinking treatment was possible, increasing the moduli in ADA/(APTES+TEOS) hybrids from 86207Pa for 1.5 ADA/Si to 362171Pa for 1.5 ADA/Si-Ca. In-situ ADA-Silica hybrid hydrogels containing both ionic and covalent crosslinking can be successfully synthesized with the proposed method., Instituto Politécnico Nacional, México (IPN-SIP 20196660 and IPN-SIP 20201294), AEI/FEDER,UE (DPI2017-90147-R), CONACYT scholarship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Modeling of Pancreatic Tumors using 3D Bioprinting

  • Banda Sánchez, C.
  • Cubo-Mateo, Nieves
  • Frutos Díaz-Alejo, Jesús
  • Earl, Julie
  • González Gómez, Icíar
  • Rodríguez-Lorenzo, Luis M.
AEI/FEDER UE (DPI2017-90147-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrasounds in cancer therapy: A summary of their use and unexplored potential

  • Frutos Díaz-Alejo, Jesús
  • González Gómez, Icíar
  • Earl, Julie
8 páginas, 2 tablas, Ultrasounds (US) are a non-ionizing mechanical wave, with less adverse effects than conventional pharmacological or surgical treatments. Different biological effects are induced in tissues and cells by ultrasound actuation depending on acoustic parameters, such as the wave intensity, frequency and treatment dose. This non-ionizing radiation has considerable applications in biomedicine including surgery, medical imaging, physical therapy and cancer therapy. Depending on the wave intensity, US are applied as high-intensity ultrasounds (HIUS) and low-intensity pulsed ultrasounds (LIPUS), with different effects on cells and tissues. HIUS produce thermal and mechanical effects, resulting in a large localized temperature increase, leading to tissue ablation and even tumor necrosis. This can be achieved by focusing low intensity waves emitted from different electrically shifted transducers, known as high-intensity focused ultrasounds (HIFU). LIPUS have been used extensively as a therapeutic, surgical and diagnostic tool, with diverse biological effects observed in tissues and cultured cells. US represent a non-invasive treatment strategy that can be applied to selected areas of the body, with limited adverse effects. In fact, tumor ablation using HIFU has been used as a curative treatment in patients with an early-stage pancreatic tumor and is an effective palliative treatment in patients with advanced stage disease. However, the biological effects, dose standardization, benefit-risk ratio and safety are not fully understood. Thus, it is an emerging field that requires further research in order to reach its full potential., The authors would like to acknowledge the following funding related with the effects of ultrasounds on cancer cells and tissues: Spanish National Plan project RETOS DPI 2017-90147-R. Intramural call for new research projects for clinical researchers and emerging research groups. IRYCIS. (2018/0240). Ibero-American Network CYTED-DITECROD-218RT0545., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Low-intensity continuous ultrasound to inhibit cancer cell migration

  • González Gómez, Icíar
  • Luzuriaga, Jon
  • Valdivieso, Alba
  • Candil, Manuel
  • Frutos, Jesús
  • López, Jaime
  • Hernández, Luis
  • Rodríguez-Lorenzo, Luis M.
  • Yaguë-Jiménez, Virginia
  • Blanco-Murillo, José Luis
  • Pinto, Alberto
  • Earl, Julie
In recent years, it has been verified that collective cell migration is a fundamental step in tumor spreading and metastatic processes. In this paper, we demonstrate for the first time how low-intensity ultrasound produces long-term inhibition of collective migration of epithelial cancer cells in wound healing processes. In particular, we show how pancreatic tumor cells, PANC-1, grown as monolayers in vitro respond to these waves at frequencies close to 1 MHz and low intensities (<100mWcm−2) for 48–72 h of culture after some minutes of a single ultrasound irradiation. This new strategy opens a new line of action to block the spread of malignant cells in cancer processes. Despite relevant spatial variations of the acoustic pressure amplitude induced in the assay, the cells behave as a whole, showing a collective dynamic response to acoustic performance. Experiments carried out with samples without previous starving showed remarkable effects of the LICUs from the first hours of culture, more prominent than those with experiments with monolayers subjected to fasting prior to the experiments. This new strategy to control cell migration demonstrating the effectiveness of LICUS on not starved cells opens a new line of action to study effects of in vivo ultrasonic actuation on tumor tissues with malignant cells. This is a proof-of-concept study to demonstrate the physical effects of ultrasound stimulation on tumor cell migration. An in-depth biological study of the effects of ultrasounds and underlying biological mechanisms is on-going but out of the scope of this article., Project PID2021-128985OB-I00 funded by MCIN/ AEI/10.13039/501100011033/“FEDER Una manera de hacer Europa and AEI, FEDER , UE DPI 2017-90147-R and Intramural call for new research projects for clinical researchers and emerging research groups IRYCIS (2018/0240)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tailoring/Tuning properties of polyester urea-urethanes through hybridization with titania obtained by sol-gel process

  • González García, Dulce María
  • Rodríguez-Lorenzo, Luis M.
  • Marcos-Fernández, Ángel
  • Jiménez-Gallego, Rodrigo
  • Sánchez Téllez, Daniela A.
  • Téllez-Jurado, Lucía
Hybrid materials have been studied because in these materials the properties of organic components, such as elasticity and biodegradability, could be combined with the properties of inorganic components, such as good biological response, thereby transforming them into a single material with improved properties. In this work, Class I hybrid materials based on polyester-ureaurethanes and titania were obtained using the modified sol–gel method. This was corroborated using the FT-IR and Raman techniques which highlighted the formation of hydrogen bonds and the presence of Ti–OH groups in the hybrid materials. In addition, the mechanical and thermal properties and degradability were measured using techniques, such as Vickers hardness, TGA, DSC, and hydrolytic degradation; these properties could be tailored according to hybridization between both organic and inorganic components. The results show that Vickers hardness increased by 20% in hybrid materials as compared to polymers; also, the surface hydrophilicity increases in the hybrid materials, improving their cell viability. Furthermore, cytotoxicity in vitro test was carried out using osteoblast cells for intended biomedical applications and they showed non-cytotoxic behavior, This work was supported by project PID2020-119047RB-I00, financed by spanish Ministerio de Ciencia e Innovación (MCIN/AEI/10.13039/501100011033/), CONACYT and IPN-SIP/20201294 from Mexico for the fellowship grant number 393020 and DPI 2017-90147-R from MINECO-AEI, Spain for the fund, Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A label free disposable device for rapid isolation of rare tumor cells from blood by ultrasounds

  • González, I.
  • Earl, J.
  • Fernández, L.J.
  • Sainz, B.
  • , Jr.
  • Pinto, A.
  • Monge, R.
  • Alcalá, S.
  • Castillejo, A.
  • Soto, J.L.
  • Carrato, A.
The use of blood samples as liquid biopsy is a label-free method for cancer diagnosis that offers benefits over traditional invasive biopsy techniques. Cell sorting by acoustic waves offers a means to separate rare cells from blood samples based on their physical properties in a label-free, contactless and biocompatible manner. Herein, we describe a flow-through separation approach that provides an efficient separation of tumor cells (TCs) from white blood cells (WBCs) in a microfluidic device, "THINUS-Chip" (Thin-Ultrasonic-Separator-Chip), actuated by ultrasounds. We introduce for the first time the concept of plate acoustic waves (PAW) applied to acoustophoresis as a new strategy. It lies in the geometrical chip design: different to other microseparators based on either bulk acoustic waves (BAW) or surface waves (SAW, SSAW and tSAW), it allows the use of polymeric materials without restrictions in the frequency of work. We demonstrate its ability to perform high-throughput isolation of TCs from WBCs, allowing a recovery rate of 84%±8% of TCs with a purity higher than 80% and combined viability of 85% at a flow rate of 80 µL/min (4.8 mL/h). The THINUS-Chip performs cell fractionation with low-cost manufacturing processes, opening the door to possible easy printing fabrication.