Pasar al contenido principal

APROVECHAMIENTO DE COMPUESTOS DE BASE LIGNINICA COMO ADITIVOS DE BIOCOMBUSTIBLES

ENE2013-41523-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSIDAD DE ZARAGOZA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bio-oil upgrading in supercritical water using Ni-Co catalysts supported on carbon nanofibres

  • Remón, Javier
  • Arauzo, J.
  • García Nieto, Lucía
  • Arcelus-Arrillaga, Pedro
  • Millan, Marcos
  • Suelves Laiglesia, Isabel
  • Pinilla Ibarz, José Luis
6 Figures, 9 Tables.-- © 2016. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This work addresses the preparation, characterisation and screening of different Ni-Co catalysts supported on carbon nanofibres (CNFs) for use in the upgrading of bio-oil in supercritical water. The aim is to improve the physicochemical properties of bio-oil so that it can be used as a fuel. The CNFs were firstly oxidised in HNO3 and afterwards subjected to a thermal treatment to selectively modify their surface chemistry prior to the incorporation of the metal active phase (Ni-Co). The CNFs and the supported catalysts were thoroughly characterised by several techniques, which allowed a relationship to be established between the catalyst properties and the upgrading results. The use of Ni-Co/CNFs for bio-oil upgrading in supercritical water (SCW) significantly improved the properties of the original feedstock. In addition, the thermal treatment to which the fibres were subjected exerted a significant influence on their catalytic properties. An increase in the severity of the thermal treatment led to a substantial reduction in the oxygen content of the CNFs, mainly due to the removal of the less stable oxygen surface groups, which allowed their surface polarity to decrease. This decrease resulted in less formation of solid products. However, it also reduced the H/C and increased the O/C ratios of the upgraded liquid. Therefore, a compromise between the yield and the properties of the upgraded bio-oil was achieved with a Ni-Co supported on a CNF with a moderate amount of oxygen surface groups., The authors wish to express their gratitude to the Aragon Government (GPT group), the European Social Fund and the Spanish MINECO (projects ENE2010-18985, ENE 2011-28318, ENE2013-41523-R and ENE2014-52189-C2-1-R) for providing financial support. Javier Remón Núñez would like to express his gratitude to the Spanish MINECO for the FPI (BES-2011-044856) and mobility (EEBB-I-14-08688) grants awarded. Jose Luis Pinilla thanks the Spanish MINECO for his Ramon y Cajal research contract., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Production of gaseous and liquid chemicals by aqueous phase reforming of crude glycerol: Influence of operating conditions on the process

  • Remón, J.
  • Giménez, J.R.
  • Valiente, A.
  • García, L.
  • Arauzo, J.
The present work studies the influence of the temperature (200-240 °C), pressure (38-50 bar), glycerol concentration (10-50 wt.%) and mass of catalyst/ glycerol mass flow rate ratio (W/mglycerol = 10-40 g catalyst min/g glycerol) during the aqueous phase reforming (APR) of a glycerol solution obtained from the production of biodiesel. The operating conditions exerted a statistically significant influence on the reforming results. Specifically, the global glycerol conversion and the carbon converted into gas and liquid products varied as follows: 4-100%, 1-80% and 16-93%, respectively. The gas phase was made up of H2 (8-55 vol.%), CO2 (34-66 vol.%), CO (0-4 vol.%) and CH4 (6-45 vol.%). The liquid phase consisted of a mixture of alcohols (monohydric: methanol and ethanol; and polyhydric: 1, 2-propanediol, 1, 2-ethanediol, 2, 3-butanediol), aldehydes (acetaldehyde), ketones (C3-ketones: acetone and 2-propanone-1-hydroxy; C4-ketones: 2-butanone-3-hydroxy and 2-butanone-1-hydroxy; and cyclic ketones), carboxylic acids (acetic and propionic acids) and esters (1, 2, 3-propanetriol-monoacetate), together with unreacted glycerol and water. The relative amount (free of water and un-reacted glycerol) of these compounds in the liquid phase was as follows: monohydric alcohols: 4-47%, polyhydric-alcohols: 14-68%, aldehydes: 0-5%, C3-ketones: 2-33%, C4-ketones: 0-10%, ciclo-ketones: 0-6%, carboxylic acids: 2-43%, and esters: 0-46%. This process turned out to be highly customisable for the valorisation of crude glycerol for the production of either gaseous or liquid products. Gas production is favoured at a low pressure (39 bar), high temperature (238 °C), high W/mglycerol ratio (38 g catalyst min/g glycerol) and employing a 15 wt.% glycerol solution. A high pressure (45 bar), medium temperature (216 °C), medium W/mglycerol ratio (22 g catalyst min/g glycerol) and the feeding of a 16 wt.% glycerol solution favours the production of liquid products.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Hydrogen production from cheese whey by catalytic steam reforming: Preliminary study using lactose as a model compound

  • Remón, J.
  • Laseca, M.
  • García, L.
  • Arauzo, J.
Cheese whey is a yellowish liquid by-product of the cheese making process. Owing to its high BOD and COD values, this feedstock should not be directly discharged into the environment without appropriate treatment. Before dealing with real cheese whey, this work addresses the production of a rich hydrogen gas from lactose (the largest organic constituent of this waste) by catalytic steam reforming. This reforming process has been theoretically and experimentally studied. The theoretical study examines the effect of the temperature (300-600 °C), lactose concentration (1-10 wt.%) and N2 (0-80 cm3 STP/min) and liquid flow (0.1-0.5 mL/min) rates on the thermodynamic composition of the gas. The results show that the temperature and lactose concentration exerted the greatest influence on the thermodynamics. The experimental study, conducted in a fixed bed reactor using a Ni-based catalyst, considers the effect of the temperature (300-600 °C), lactose concentration (1-10 wt.%) and spatial time (4-16 g catalyst min/g lactose) on the global lactose conversion, product distribution on a carbon basis (gas, liquid and solid) and the compositions of the gas and liquid phases. Complete lactose conversion was achieved under all the experimental conditions. The carbon converted into gas, liquid and solid was 2-97%, 0-66% and 0-94%, respectively. The gas phase was made up of a mixture of H2 (0-70 vol.%), CO2 (20-70 vol.%), CO (2-34 vol.%) and CH4 (0-3 vol.%). The liquid phase consisted of a mixture of aldehydes, ketones, carboxylic acids, sugars, furans, alcohols and phenols. Optimal conditions for cheese whey valorisation were sought considering the energetic aspects of the process. Using a lactose concentration similar to that of cheese whey (5.5 wt.%), maxima for the CC gas (88%) and the proportion of H2 (67 vol.%) in the gas together with a carbon-free liquid stream can be achieved at 586 °C using a spatial time of 16 g catalyst min/g lactose. Theoretically, the combustion of 20% of this gas provides the energy necessary for the process enabling the transformation of 68% of the carbon present in the initial effluent into a H2 rich gas (67 vol.%) with a global H2 yield of 16 mol H2/mol lactose. In a real case it would be necessary to increase the amount of gas combusted to compensate for heat losses.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of biodiesel-derived impurities (acetic acid, methanol and potassium hydroxide) on the aqueous phase reforming of glycerol

  • Remón, J.
  • Ruiz, J.
  • Oliva, M.
  • García, L.
  • Arauzo, J.
This work analyses the influence of three biodiesel-derived impurities (CH3OH, CH3COOH and KOH) on the aqueous phase reforming of glycerol at 220 °C and 44 bar using a Ni-La/Al2O3 catalyst. The experiments were planed according to a factorial 2k design and analysed by means of an analysis of variance (ANOVA) test to identify the effect of each impurity and all possible binary and ternary combinations. The presence of CH3OH decreased the glycerol conversion, while CH3COOH and KOH decreased and increased the gas production, respectively. Catalyst deactivation took place under acidic conditions due to the loss of part of the active phase of the catalyst through leaching. The gas phase was made up of H2, CO2, CO and CH4. KOH exerted the greatest influence on the gas composition, increasing H2 production due to the greater gas production and the lower H2 consumption in the hydrogenation reactions. The liquid phase was made up of aldehydes, monohydric and polyhydric alcohols, C3 and C4 ketones and esters. CH3OH increased the proportion of monohydric alcohols, while CH3COOH promoted dehydration reactions, leading to an increase in the relative amount of C3-ketones.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Analysis and optimisation of H2 production from crude glycerol by steam reforming using a novel two step process

  • Remón, J.
  • Jarauta-Córdoba, C.
  • García, L.
  • Arauzo, J.
This work studies the valorisation of biodiesel-derived glycerol to produce a hydrogen rich gas by means of a two-step sequential process. Firstly, the crude glycerol was purified with acetic acid to reduce problematical impurities. The effect of the final pH (5-7) on the neutralisation process was addressed and it was found that a pH of 6 provided the best phase separation and the greatest glycerol purity. Secondly, the refined glycerol was upgraded by catalytic steam reforming and this step was theoretically and experimentally studied. The theoretical study analyses the effect of the temperature (400-700°C), glycerol concentration (10-50 wt.%) and N2 (225-1347 cm3 STP/min) and liquid flow (0.5-1 mL/min) rates on the thermodynamic composition of the gas. The results show that the temperature and glycerol concentration exerted the greatest influence on the thermodynamics. The experimental study considers the effect of the temperature (400-700°C), glycerol concentration (10-50 wt.%) and spatial time (3-17 g catalyst min/g glycerol) on the product distribution in carbon basis (gas, liquid and solid) and on the composition of the gas and liquid phases. The experiments were planned according to a 2 level 3 factor Box-Wilson Central Composite Face Centred (CCF, a: ± 1) design, which is suitable for studying the influence of each variable as well as all the possible interactions between variables. The results were analysed with an analysis of variance (ANOVA) with 95% confidence, enabling the optimisation of the process. The gas phase was made up of a mixture of H2 (65-95 vol.%), CO2 (2-29 vol.%), CO (0-18 vol.%) and CH4 (0-5 vol.%). Temperatures of 550°C and above enabled thermodynamic compositions for the gas to be achieved and helped diminish carbon formation. A possible optimum for H2 production was found at a temperature of around 680°C, feeding a glycerol solution of 37 wt.% and using a spatial time of 3 g catalyst min/g glycerol. These conditions provide a 95% carbon conversion to gas, having the following composition: 67 vol.% H2, 22 vol.% CO2, 11 vol.% CO and 1 vol.% CH4.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Production of gaseous and liquid bio-fuels from the upgrading of lignocellulosic bio-oil in sub- and supercritical water: effect of operating conditions on the process

  • Remon, J.
  • Arcelus-Arrillaga, P.
  • Garcia, L.
  • Arauzo, J.
This work analyses the influence of the temperature (310–450 C), pressure (200–260 bar), catalyst/biooil mass ratio (0–0.25 g catalyst/g bio-oil), and reaction time (0–60 min) on the reforming in sub- and supercritical water of bio-oil obtained from the fast pyrolysis of pinewood. The upgrading experiments were carried out in a batch micro-bomb reactor employing a co-precipitated Ni–Co/Al–Mg catalyst. This reforming process turned out to be highly customisable for the valorisation of bio-oil for the production of either gaseous or liquid bio-fuels. Depending on the operating conditions and water regime (sub/supercritical), the yields to upgraded bio-oil (liquid), gas and solid varied as follows: 5–90%, 7–91% and 3–31%, respectively. The gas phase, having a LHV ranging from 2 to 17 MJ/m3 STP, was made up of a mixture of H2 (9–31 vol.%), CO2 (41–84 vol.%), CO (1–22 vol.%) and CH4 (1–45 vol.%). The greatest H2 production from bio-oil (76% gas yield with a relative amount of H2 of 30 vol.%) was achieved under supercritical conditions at a temperature of 339 C, 200 bar of pressure and using a catalyst/bio-oil ratio of 0.2 g/g for 60 min. The amount of C, H and O (wt.%) in the upgraded bio-oil varied from 48 to 74, 4 to 9 and 13 to 48, respectively. This represents an increase of up to 37% and 171% in the proportions of C and H, respectively, as well as a decrease of up to 69% in the proportion of O. The HHV of the treated bio-oil shifted from 20 to 35 MJ/kg, which corresponds to an increase of up to 89% with respect to the HHV of the original bio-oil. With a temperature of around 344 C, a pressure of 233 bar, a catalyst/bio-oil ratio of 0.16 g/g and a reaction time of 9 min a compromise was reached between the yield and the quality of the upgraded liquid, enabling the transformation of 62% of the bio-oil into liquid with a HHV (29 MJ/kg) about twice as high as that of the original feedstock (17 MJ/kg).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Bio-oil upgrading in supercritical water using Ni-Co catalysts supported on carbon nanofibres

  • Remón, J.
  • Arauzo, J.
  • García, L.
  • Arcelus-Arrillaga, P.
  • Millan, M.
  • Suelves, I.
  • Pinilla, J. L.
This work addresses the preparation, characterisation and screening of different Ni-Co catalysts supported on carbon nanofibres (CNFs) for use in the upgrading of bio-oil in supercritical water. The aim is to improve the physicochemical properties of bio-oil so that it can be used as a fuel. The CNFs were firstly oxidised in HNO3 and afterwards subjected to a thermal treatment to selectively modify their surface chemistry prior to the incorporation of the metal active phase (Ni-Co). The CNFs and the supported catalysts were thoroughly characterised by several techniques, which allowed a relationship to be established between the catalyst properties and the upgrading results. The use of Ni-Co/CNFs for bio-oil upgrading in supercritical water (SCW) significantly improved the properties of the original feedstock. In addition, the thermal treatment to which the fibres were subjected exerted a significant influence on their catalytic properties. An increase in the severity of the thermal treatment led to a substantial reduction in the oxygen content of the CNFs, mainly due to the removal of the less stable oxygen surface groups, which allowed their surface polarity to decrease. This decrease resulted in less formation of solid products. However, it also reduced the H/C and increased the O/C ratios of the upgraded liquid. Therefore, a compromise between the yield and the properties of the upgraded bio-oil was achieved with a Ni-Co supported on a CNF with a moderate amount of oxygen surface groups.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Antioxidants for biodiesel: Additives prepared from extracted fractions of bio-oil

  • García Rodríguez, Manuel
  • Botella Abad, Lucía
  • Gil-Lalaguna, Noemí
  • Arauzo Pérez, Jesús
  • Gonzalo Callejo, Aberto
  • Sánchez Cebrián, José Luis
Unlike petroleum diesel, the chemical structure of biodiesel makes it prone to oxidation during long-term storage, thus involving fuel quality deterioration. Therefore, the addition of antioxidants is usually required to meet the quality standards for biodiesel commercialization. Synthetic sterically-hindered phenols have been usually employed for this purpose as free radical scavenging antioxidants. However, naturally occurring phenolics are also available, for example, in the bio-oil produced in the pyrolysis of lignocellulosic biomass. In this work, the antioxidant potential of extracted fractions of lignocellulosic bio-oil has been evaluated. Different organic solvents were tested as extraction agents, acetate esters being the best ones for incorporating bio-oil antioxidant compounds into biodiesel. In the best case, the incorporation of a small concentration of bio-oil compounds (< 4 wt.%) led to an improvement of the biodiesel oxidation stability of 475% which, in our case, was enough to meet the European standard requirement.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Bio-Oil Hydrotreatment for Enhancing Solubility in Biodiesel and the Oxydation Stability of Resulting Blends

  • Botella, L.
  • Stankovikj, F.
  • Sanchez, J.L.
  • Gonzalo, A.
  • Arauzo, J.
  • Garcia-Perez, M.
The major challenge for the pyrolytic conversion of lignocellulosic materials into crude bio-oil is the poor quality of the final product. Several strategies (addition of solvents, production of emulsions, and extraction with biodiesel) have been studied to improve its fuel properties. The extraction with biodiesel is an interesting solution because it allows direct utilization of some bio-oil fractions as fuels. However, fraction extracted with biodiesel is typically between 10 and 18 wt. %. In this paper we studied mild hydrotreatment of pyrolysis oil to enhance its solubility in biodiesel. The study was conducted with BTG and Amaron oils hydrotreated at temperatures between 200 and 325 degrees C in the presence of Ru/C catalyst. Hydrotreated oils generated three phases: top oil (light hydrocarbons), middle aqueous phase and bottom heavy oil phase. Each of the phases was characterized and the content of acetic acid, phenols, aromatic compounds, and linear alkane hydrocarbons quantified. The upgraded bio-oils were more soluble in biodiesel than the crude bio- oils, obtaining blends with up to 48 and 38 wt. % for the BTG and Amaron bio- oil, respectively. Some of the fuel properties of the resulting blends are also reported here.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Cheese whey management by catalytic steam reforming and aqueous phase reforming

  • Remón, J.
  • García, L.
  • Arauzo, J.
Cheese whey is a yellowish liquid by-product of the cheese making process. Owing to its high BOD and COD values, this feedstock should not be directly discharged into the environment without appropriate treatment. The management of this wastewater has become an important issue, and new treatments must be sought. This work addresses the valorisation of cheese whey by steam reforming and aqueous phase reforming. The catalytic steam reforming of cheese whey turned out to be a promising valorisation route for H2 production from this effluent. This process enabled the organic compounds present in the cheese whey to be transformed into a rich H2 gas (35% of the C of the feed was transformed into a gas with 70 vol.% of H2). This significantly reduced the amount of carbon present in the original feedstock, producing an almost carbon-free liquid stream. The aqueous phase reforming of cheese whey allowed 35% of the carbon present in the whey to be transformed into gases and 45% into valuable liquids. The gas was principally made up of H2 and CO2, while a mixture of added-value liquids such as aldehydes, carboxylic acids, alcohols and ketones constituted the liquid phase. However, both valorisation routes produced a substantial amount of solid. The formation of this solid was promoted by the presence of salts in the original feedstock and caused operational problems for both valorisation processes. In addition, it hampered gas production in the case of steam reforming and reduced gas and liquid formation when using aqueous phase reforming as the valorisation route. The filtration of cheese whey slightly decreased the solid formation in both processes due to the reduction of proteins and fats, both of which partly contribute to such formation. Less solid was formed in the experiments conducted with lactose than in those conducted with whole and with filtered cheese whey.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Simultaneous production of gaseous and liquid biofuels from the synergetic co-valorisation of bio-oil and crude glycerol in supercritical water

  • Remón Núñez, Javier
  • Arcelus-Arrillaga, Pedro
  • García Nieto, Lucía
  • Arauzo Pérez, Jesús
This work addresses the co-valorisation in supercritical water of bio-oil obtained from the fast pyrolysis of wood and crude glycerol yielded as a by-product during biodiesel production. The experiments were conducted at 380¿°C and 230¿bar for 30¿min with a Ni-Co/Al-Mg catalyst, analysing the effects on the process of the catalyst loading (0–0.25¿g catalyst/g organics) and feed composition (each material alone and all possible binary mixtures). The yields to gas, upgraded bio-oil (liquid) and solid varied as follows: 4–87%, 0–46% and 0–18%, respectively. A synergistic interaction between crude glycerol and bio-oil took place during the upgrading process, which allowed the complete and simultaneous transformation of both materials into gas and liquid bio-fuels with a negligible solid formation. The compositions of the gas and the upgraded liquid can be easy tailored by adjusting the catalyst amount and the composition of the feed. The gas phase was made up of H2 (7–49¿vol.%), CO2 (31–56¿vol.), CO (0–7¿vol.%) and CH4 (6–57¿vol.%) and had a Lower Heating Value (LHV) ranging from 8 to 22¿MJ/m3 STP. The upgraded bio-oil consisted of a mixture of carboxylic acids (0–73%), furans (0–7%), phenols (0–85%), ketones (0–22%) and cyclic compounds (0–53%). The proportions of C, H and O in the liquid shifted between 66–77¿wt.%, 7–11¿wt.% and 15–25¿wt.%, respectively, while its Higher Heating Value (HHV) ranged from 29 to 34¿MJ/kg. An optimum for the simultaneous production of gas and liquid bio-fuels was achieved with a solution having equal amounts of each material and employing a catalyst amount of 0.25¿g catalyst/g organics. Under such conditions, 37% of the bio-oil was transformed into an upgraded liquid having a HHV (32¿MJ/kg) two times higher than the original material (16¿MJ/kg) with a negligible solid formation; the rest of the bio-oil and all the crude glycerol being converted into a rich CH4 (55¿vol.%) biogas with a high LHV (21¿MJ/m3 STP). This represents a step-change in future energy production and can help to establish the basis for a more efficient and sustainable biomass valorisation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Hydrogenolysis of glycerol with external h2 supply as value-added liquid chemicals source

  • Jarauta-Córdoba, C.
  • Ehrmaier, A.
  • Denk, C.
  • Lercher, J.A.
  • García, L.
  • Ruíz, J.
  • Arauzo, J.
The hydrogenolysis process of glycerol with external H2 supply has been studied using Ni-exchanged zeolites (FAU, LTA, ZSM-5). The reaction temperature and the oxidation state of the active phase were investigated in this work. Ni/zeolite catalysts were tested for 3 hours in a batch reactor, at different temperatures between 200 and 250 ºC and at 33 bar of initial H2 pressure. A water solution of 5 wt.% glycerol was used as a feedstock. The liquid products collected were analyzed afterwards by GC-MS and GC-FID. Several catalyst characterization techniques were performed: N2 physisorption, XRD, AAS, NH3-TPD and FTIR of adsorbed probe molecule (pyridine or NH3). The relevance of the metallic function for the hydrogenation reaction was proved. In most cases, the increase of the reaction temperature between 200 and 250 ºC implies a steady increase in the glycerol conversion and in the carbon conversion to liquid products, both for the reduced and non-reduced catalysts. The temperature also influences the selectivity to liquid products. Moreover, some temperatures were proposed as optimal for the production of certain liquids under these conditions. El proceso de hidrogenólisis del glicerol con suministro externo de H2 se ha estudiado utilizando zeolitas intercambiadas con Ni (FAU, LTA, ZSM-5). En este trabajo se investigaron la temperatura de reacción y el estado de oxidación de la fase activa. Los catalizadores de Ni/zeolita se probaron durante 3 horas en un reactor discontinuo, a diferentes temperaturas entre 200 y 250 ºC y a 33 bar de presión inicial de H2. Se utilizó como materia prima una solución acuosa de 5% en peso de glicerol. Los productos líquidos recogidos se analizaron posteriormente mediante GC-MS y GC-FID. Se realizaron varias técnicas de caracterización de catalizadores: fisisorción de N2, XRD, AAS, NH3-TPD y FTIR de la molécula sonda adsorbida (piridina o NH3). Se demostró la relevancia de la función metálica para la reacción de hidrogenación. En la mayoría de los casos, el aumento de la temperatura de reacción entre 200 y 250 ºC implica un aumento constante en la conversión de glicerol y en la conversión de carbono a productos líquidos, tanto para los catalizadores reducidos como para los no reducidos. La temperatura también influye en la selectividad hacia los productos líquidos. Además, se propusieron algunas temperaturas como óptimas para la producción de determinados líquidos en estas condiciones.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Obtaining biodiesel antioxidant additives by hydrothermal treatment of lignocellulosic bio-oil

  • Gil-Lalaguna, N.
  • Bautista, A.
  • Gonzalo, A.
  • Sánchez, J.L.
  • Arauzo, J.
The potential use of bio-oil as a small-dosage additive for improving biodiesel oxidation stability has been investigated in this work. Lignocellulosic bio-oil was high-pressure processed under different mixtures of water and organic solvents in order to promote depolymerization of the high molecular lignin still present in bio-oil and increase the content of phenolics, whose antioxidant potential is known. In fact, the antioxidant potential of bio-oil was found to noticeably enhance after the hydrothermal treatment. While the addition of 2% of crude bio-oil improved biodiesel oxidation stability by 135%, the same amount of hydrotreated bio-oil (water, 300 °C, 8.5 MPa) led to an oxidation stability improvement of 400%, which was related to the increase in the concentration of catechol, as well as to the modification of antioxidant properties of the pyrolytic lignin fraction.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of acid (CH3COOH, H2SO4 and H3PO4) and basic (KOH and NaOH) impurities on glycerol valorisation by aqueous phase reforming

  • Remón, J.
  • Jarauta-Córdoba, C.
  • García, L.
  • Arauzo, J.
This work analyses and compares, under the same operating conditions (220 °C and 44 bar with a Ni-La/Al2O3 catalyst), the effects of some of the most common acid (CH3COOH, H2SO4, H3PO4) and basic (KOH and NaOH) biodiesel-derived impurities on the aqueous phase reforming (APR) of a 30 wt.% glycerol solution. The statistical analysis of the results revealed that the impurities did not greatly influence the initial reforming results. Conversely, they significantly influenced the catalyst deactivation, which resulted in different evolutions over time for the glycerol conversion, liquid production and the composition of the gas and liquid phases. Significant decreases over time in the glycerol conversion and liquid production were detected, the severity of the decay being as follows: H3PO4 (KOH = NaOH) > H2SO4 (KOH < NaOH) > CH3COOH (KOH < NaOH). The characterisation of the spent catalyst and the liquid phases revealed that poisoning/fouling, and catalyst active phase or support modification (leaching and crystalline phases alteration), were the major deactivation mechanisms. The proportions of metals (K or Na) deposited on the catalysts with the different acids was as follows: H3PO4 > H2SO4 > CH3COOH. In addition, S and P were also deposited on the catalyst, while boehmite and other new crystalline phases were detected in the spent catalyst after the APR reaction.