Pasar al contenido principal

RED TEMATICA PARA EL CONTROL Y CARACTERIZACION DE LUZ LASER

FIS2015-71933-REDT

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Redes Investigación /Redes Excelencia
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Investigación, Desarrollo e Innovación
Centro beneficiario UNIVERSIDAD DE SALAMANCA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Outdoor performance evaluation of a holographic solar concentrator optimized for building integration

  • Marín Sáez, Julia
  • Chemisana Villegas, Daniel
  • Atencia Carrizo, Jesús
  • Collados, María Victoria
A holographic solar concentrating system with a Silicon photovoltaic (PV) cell is designed, constructed and characterized. The design is based on a previous system and is further optimized. The cylindrical holographic lenses forming the concentrating system are modeled with a ray-tracing algorithm based on Coupled Wave Theory and are recorded on Bayfol® HX photopolymer. Measurements are carried out outdoors with solar illumination and provide a current density of 146 mA/cm2 with a current concentration factor of 3.48, validating the theoretical simulations results (172 mA/cm2 and 3.81, respectively). The effect of the temperature on the performance of the Holographic Optical Elements (HOEs) is studied and taking it into account by assuming a 1.3° tilt of the fringes of the hologram caused by thermal expansion (which is reversible if the HOEs are encapsulated and sealed) provides simulation results closer to the experimental ones (a current density value of 155 mA/cm2 and current concentration of 3.43). The ageing of HOEs recorded in Bayfol® HX photopolymer due to the outdoor environmental conditions is also analyzed, revealing the need of encapsulation and sealing., The authors would like to thank Dr. Enrico Orselli (Covestro Deutschland AG) for supplying the recording photopolymer material. This research has been supported by the Spanish Ministerio de Economía y Competitividad (grants ENE2016-81040-R and FIS2015-71933-REDT), the Diputación General de Aragón-Fondo Social Europeo (TOL research group, E44_17R), the Universidad de Zaragoza (UZ2018-CIE-07) and the Generalitat de Catalunya (grants 2017 SGR 1276, 2017FI_B2_00127 and ICREA Academia).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Laser induced periodic surface structures on polymer nanocomposites with carbon nanoadditives

  • Rodríguez-Beltrán, René, I.
  • Paszkiewicz, S.
  • Szymczyk, A.
  • Roslaniec, Z.
  • Nogales, Aurora
  • Ezquerra, Tiberio A.
  • Castillejo, Marta
  • Moreno, Pablo
  • Rebollar, Esther
7 pags., 7 figs., tab., Laser induced periodic surface structures (LIPSS) are formed on poly(trimethylene terephthalate) and its composites with single-walled carbon nanotubes (SWCNT) and with both SWCNT and expanded graphite (EG) upon irradiation with a Q-Switched Nd:YAG laser (266 nm, 8 ns). The morphology of the polymer films was characterized by atomic force microscopy. A cantilever with a colloidal probe was used to obtain information about surface adhesion. Surface energies were estimated by contact angle measurements using different liquids. Chemical modification in the materials upon irradiation was assessed by Raman spectroscopy. Results show a dependence of the number of pulses required for LIPSS formation as a consequence of the presence of the carbon nanoadditive and an increase of the hydrophilic character of surfaces after irradiation. Moreover, the polar component of the surface free energy changes significantly and surface adhesion increases by the addition of the additive to the polymer matrix. Additionally, the adhesion force decreases after laser nanostructuring as a consequence of a lower contact area in the nanostructured material., The authors gratefully acknowledge financial support from the MINECO (FIS2013-44174-P, MAT2014-59187-R, MAT2015-66443-C02-1-R, FIS2015-71933-REDT, CTQ2016- 75880-P) and Junta de Castilla y León (Project SA046U16). RIR is grateful for the International Scholarship number 314197 provided by Consejo Nacional de Ciencia y Tecnología (CONACyT-México) and E.R. thanks MINECO for a Ramón y Cajal contract (RYC- 2011-08069)., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Outdoor performance evaluation of a holographic solar concentrator optimized for building integration

  • Marín Sáez, Julia
  • Chemisana Villegas, Daniel
  • Atencia Carrizo, Jesús
  • Collados, María Victoria
A holographic solar concentrating system with a Silicon photovoltaic (PV) cell is designed, constructed and characterized. The design is based on a previous system and is further optimized. The cylindrical holographic lenses forming the concentrating system are modeled with a ray-tracing algorithm based on Coupled Wave Theory and are recorded on Bayfol® HX photopolymer. Measurements are carried out outdoors with solar illumination and provide a current density of 146 mA/cm2 with a current concentration factor of 3.48, validating the theoretical simulations results (172 mA/cm2 and 3.81, respectively). The effect of the temperature on the performance of the Holographic Optical Elements (HOEs) is studied and taking it into account by assuming a 1.3° tilt of the fringes of the hologram caused by thermal expansion (which is reversible if the HOEs are encapsulated and sealed) provides simulation results closer to the experimental ones (a current density value of 155 mA/cm2 and current concentration of 3.43). The ageing of HOEs recorded in Bayfol® HX photopolymer due to the outdoor environmental conditions is also analyzed, revealing the need of encapsulation and sealing., The authors would like to thank Dr. Enrico Orselli (Covestro Deutschland AG) for supplying the recording photopolymer material. This research has been supported by the Spanish Ministerio de Economía y Competitividad (grants ENE2016-81040-R and FIS2015-71933-REDT), the Diputación General de Aragón-Fondo Social Europeo (TOL research group, E44_17R), the Universidad de Zaragoza (UZ2018-CIE-07) and the Generalitat de Catalunya (grants 2017 SGR 1276, 2017FI_B2_00127 and ICREA Academia).