Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Helvia. Repositorio Institucional de la Universidad de Córdoba
Publicación Artículo científico (JournalArticle)

Effect of incorporating municipal solid waste incinerated bottom ash in alkali-activated fly ash concrete subjected to accelerated CO2 curing

  • Suescum-Morales, David
  • Vasco Silva, Rui
  • Bravo, Miguel
  • Jiménez Romero, José Ramón
  • Fernández Rodríguez, José María
  • De Brito, Jorge
The effect of incorporating bottom ash from municipal solid waste incineration (MIBA) as partial replacement for fly ash (FA) (0%, 15% and 30%) was studied on alkali-activated mortars under two curing environments: conventional climatic chamber (∼0.04% CO2) and carbonation chamber (5% CO2). The microstructural characterization showed that the use of MIBA resulted in a decrease of calcium silicate hydrate gel (C–S–H) and sodium aluminosilicate hydrate (N-A-S-H) observed as “rounded growths” worsening the macrostructural behaviour (compressive/flexural strength, ultrasonic pulse velocity, dynamic Young’ modulus, dry bulk density, shrinkage, depth of carbonation and porosity accessible to water). The accelerated CO2 curing stage produced high amounts of aragonite, observed as “needle-like” formations improving the macrostructural behaviour. One tonne of mixture with MIBA and CO2 curing could decarbonise approximately 3695, 7391 and 10163 m3 of air volume at the age of 7, 14 and 28 days. The combined substitution of FA with MIBA and CO2 curing can be a highly viable technique in plain precast products
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publicación Artículo científico (JournalArticle)

Effect of reactive magnesium oxide in alkali-activated fly ash mortars exposed to accelerated CO2 curing

  • Suescum-Morales, David
  • Bravo, Miguel
  • Vasco Silva, Rui
  • Jiménez Romero, José Ramón
  • Fernández Rodríguez, José María
  • De Brito, Jorge
The effect of reactive magnesium oxide (MgO) as partial fly ash replacement in alkali-activated fly ash mortars (0, 10 and 20 %) was studied under two different environments: conventional climatic chamber and climatic carbonation chamber with 0.04 and 5 % level of CO2 respectively. A complete characterisation of all raw materials was performed. The effect of replacing fly ash with MgO resulted in a decline of compressive (up to 52.3 % at 28 days of age and 20% of MgO replacement) and flexural strength, ultrasonic pulse velocity and dynamic Young’s modulus mainly due to the formation of weak and expansive brucite, detected by X-ray diffraction (XRD). Carbonation depth and shrinkage also were obtained. CO2 curing improved the physicomechanical properties, due to the formation of nesquehonite in samples with MgO. An improvement of CO2 absorption of 2 g CO2/kg mixes with the CO2 curing and the substitution of fly ash with MgO was obtained (determined by thermogravimetric and differential thermal analysis). The increase in mass due to CO2 capture was of 6.91%, 9.39% and 12.26% at the age of 7, 14 and 28 days, respectively, when compared to mixes cured with 0.04 (reference) and 5 % (CO2 curing) level of CO2
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publicación Artículo científico (JournalArticle)

Potential CO2 capture in one-coat limestone mortar modified with Mg3Al–CO3 calcined hydrotalcites using ultrafast testing technique

  • Suescum-Morales, David
  • Cantador Fernández, David
  • Jiménez Romero, José Ramón
  • Fernández Rodríguez, José María
The objective of this work is to quantify the CO2 capture capacity of an industrial one-coat limestone mortar containing different percentages of calcined Mg3Al–CO3 hydrotalcite (HT C2500) added (0, 2.5, and 5%) in different hardening environments (with different concentrations of CO2). The maximum CO2 capture capacity (calculated by thermogravimetric analysis) for 0, 2.5, and 5% of added HT C2500 were 1127, 1143, and 1223 g·m−2 (as rendering), respectively. This amount of CO2 is approximately one-third of that emitted during the manufacture of the cement used for this mortar. The addition of calcined hydrotalcite worsened the compressive strengths obtained in all the hardening environments studied. A 5% of calcined hydrotalcite increased the CO2 capture capacity by 8.52% with respect to the reference mortar. Ultrafast testing method (using CO2 isotherms at high pressure) has been proposed to quantify the CO2 capture capacity in very short period of time. A slight modification in the dosage of calcined hydrotalcite in an industrial one-coat mortar can contribute to mitigating climate change