Pasar al contenido principal

NUEVAS ALTERNATIVAS DE CAPTURA Y UTILIZACION DE CO2 EN PREFABRICADOS DE HORMIGON

PID2019-111029RB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE CORDOBA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

Helvia. Repositorio Institucional de la Universidad de Córdoba
Publicación Artículo científico (JournalArticle)

Effect of incorporating municipal solid waste incinerated bottom ash in alkali-activated fly ash concrete subjected to accelerated CO2 curing

  • Suescum-Morales, David
  • Vasco Silva, Rui
  • Bravo, Miguel
  • Jiménez Romero, José Ramón
  • Fernández Rodríguez, José María
  • De Brito, Jorge
The effect of incorporating bottom ash from municipal solid waste incineration (MIBA) as partial replacement for fly ash (FA) (0%, 15% and 30%) was studied on alkali-activated mortars under two curing environments: conventional climatic chamber (∼0.04% CO2) and carbonation chamber (5% CO2). The microstructural characterization showed that the use of MIBA resulted in a decrease of calcium silicate hydrate gel (C–S–H) and sodium aluminosilicate hydrate (N-A-S-H) observed as “rounded growths” worsening the macrostructural behaviour (compressive/flexural strength, ultrasonic pulse velocity, dynamic Young’ modulus, dry bulk density, shrinkage, depth of carbonation and porosity accessible to water). The accelerated CO2 curing stage produced high amounts of aragonite, observed as “needle-like” formations improving the macrostructural behaviour. One tonne of mixture with MIBA and CO2 curing could decarbonise approximately 3695, 7391 and 10163 m3 of air volume at the age of 7, 14 and 28 days. The combined substitution of FA with MIBA and CO2 curing can be a highly viable technique in plain precast products
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publicación Artículo científico (JournalArticle)

Effect of reactive magnesium oxide in alkali-activated fly ash mortars exposed to accelerated CO2 curing

  • Suescum-Morales, David
  • Bravo, Miguel
  • Vasco Silva, Rui
  • Jiménez Romero, José Ramón
  • Fernández Rodríguez, José María
  • De Brito, Jorge
The effect of reactive magnesium oxide (MgO) as partial fly ash replacement in alkali-activated fly ash mortars (0, 10 and 20 %) was studied under two different environments: conventional climatic chamber and climatic carbonation chamber with 0.04 and 5 % level of CO2 respectively. A complete characterisation of all raw materials was performed. The effect of replacing fly ash with MgO resulted in a decline of compressive (up to 52.3 % at 28 days of age and 20% of MgO replacement) and flexural strength, ultrasonic pulse velocity and dynamic Young’s modulus mainly due to the formation of weak and expansive brucite, detected by X-ray diffraction (XRD). Carbonation depth and shrinkage also were obtained. CO2 curing improved the physicomechanical properties, due to the formation of nesquehonite in samples with MgO. An improvement of CO2 absorption of 2 g CO2/kg mixes with the CO2 curing and the substitution of fly ash with MgO was obtained (determined by thermogravimetric and differential thermal analysis). The increase in mass due to CO2 capture was of 6.91%, 9.39% and 12.26% at the age of 7, 14 and 28 days, respectively, when compared to mixes cured with 0.04 (reference) and 5 % (CO2 curing) level of CO2
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publicación Artículo científico (JournalArticle)

Accelerated carbonation of fresh cement-based products containing recycled masonry aggregates for CO2 sequestration

  • Suescum-Morales, David
  • Kalinowska-Wichrowska, Katarzyna
  • Fernandez Rodriguez, José María
  • Jiménez Romero, José Ramón
This study examines the effects of accelerated carbonation on the mechanical properties, dry bulk density, porosity accessible to water, and the CO2 sequestration capacity of a porous cement-based material that contains different replacement ratios of natural aggregate (NA) by recycled masonry aggregate (RMA). Two hardening environments were used: a conventional climate chamber as a reference (0.04 % CO2) and a climatic chamber for accelerated carbonation (5% CO2), with curing times of 1, 3, and 7 days. A volumetric substitution method where NA was replaced with RMA did not significantly affect its mechanical properties. Accelerated carbonation reduced the curing time, improved mechanical properties, increased dry bulk density, and decreased accessible porosity for water for all the mixes studied. The maximum CO2 sequestration for cement-based materials made with mixed recycled aggregates was 27 kg CO2/t of mix. Accelerated carbonation of fresh cement-based products containing RMA is a promising CO2 capture and utilisation technology for precast non-reinforced concrete product manufacturing
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publicación Artículo científico (JournalArticle)

Mitigation of CO2 emissions by hydrotalcites of Mg3Al-CO3 at 0 °C and high pressure

  • Suescum-Morales, David
  • Cantador Fernández, David
  • Jiménez Romero, José Ramón
  • Fernández Rodríguez, José María
This work shows the maximum CO2 capture capacity, using CO2 isotherms at 0, 20 and 30 °C and pressures of up to 35 atm, of four adsorbents with different particle size distribution and different pore size distribution: two hydrotalcites of Mg3Al-CO3, one synthesized in laboratory (C1) and another commercial (C2) and two calcined (C1 500 and C2 500) obtained from C1 and C2 by calcination at 500 °C for 2 h, respectively. The maximum capture capacities were obtained for samples calcined (CLDH), 98.16 mg·g−1 for C2 500 sample and 142.02 mg·g−1 for sample C1 500, both at 0 °C and 34.28 atm. The capture capacity of the C2 500 sample was the least influenced by temperature changes, which could be related to the porous structure of the samples. Consequently, for applications that are carried out between 0 and 30 °C, the best sample will be C2 500. Previously the samples were characterized by X-ray diffraction, transmission and scanning electron microscopy, thermogravimetric and thermo-differential analysis, particle size distribution and pore size distribution by N2 adsorption isotherms. The CO2 adsorption isotherms data were adjusted to the Freundlich, Langmuir, Dubinin-Radushkevich y Temkin models. These two last models confirmed that the nature for CO2 adsorption was physical. In short, this work showed the usefulness of calcined hydrotalcite as a CO2 adsorbent, using low temperature (0 °C) and high pressure (34.28 atm) as working conditions.
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publicación Artículo científico (JournalArticle)

Potential CO2 capture in one-coat limestone mortar modified with Mg3Al–CO3 calcined hydrotalcites using ultrafast testing technique

  • Suescum-Morales, David
  • Cantador Fernández, David
  • Jiménez Romero, José Ramón
  • Fernández Rodríguez, José María
The objective of this work is to quantify the CO2 capture capacity of an industrial one-coat limestone mortar containing different percentages of calcined Mg3Al–CO3 hydrotalcite (HT C2500) added (0, 2.5, and 5%) in different hardening environments (with different concentrations of CO2). The maximum CO2 capture capacity (calculated by thermogravimetric analysis) for 0, 2.5, and 5% of added HT C2500 were 1127, 1143, and 1223 g·m−2 (as rendering), respectively. This amount of CO2 is approximately one-third of that emitted during the manufacture of the cement used for this mortar. The addition of calcined hydrotalcite worsened the compressive strengths obtained in all the hardening environments studied. A 5% of calcined hydrotalcite increased the CO2 capture capacity by 8.52% with respect to the reference mortar. Ultrafast testing method (using CO2 isotherms at high pressure) has been proposed to quantify the CO2 capture capacity in very short period of time. A slight modification in the dosage of calcined hydrotalcite in an industrial one-coat mortar can contribute to mitigating climate change