Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Catalytic hydrolysis of cellulose to glucose: on the influence of graphene oxide morphology under microwave radiation

  • Frecha, E.
  • Torres, D.
  • Remón, J.
  • Gammons, R.
  • Matharu, A.S.
  • Suelves, I.
  • Pinilla, J.L.
Carbon nanostructures provide a unique platform for the synthesis of novel catalysts for biomass conversion. In this work, a set of graphene oxide (GO)-based materials (nanofibers (GONF), sheets of few-layers (FLGO), and quantum dots (GOQD)), differing structurally in morphology and size, was prepared from fishbone-carbon nanofibers (CNF) and their catalytic behavior was compared on the hydrolysis of amorphous cellulose under microwave (MW) radiation. First, the influence of the reaction temperature (135–180 ºC), holding time (0–120 min), catalyst morphology and cellulose/water ratio (0.25–2.0 wt%) was thoroughly screened and compared with conventional heating mode. The use of GO morphologies in concert with MW energy showed the potential to achieve similar kinetic profiles than previously reported sulfonated carbons (110 kJ/mol) but using considerably less amount of catalyst (cellulose-to-catalyst ratio 12-fold lower). Overall, the reactivity of the GO-catalyst was related to their degree of oxidation/exfoliation, decreasing as follows: GOQD > FLGO > GONF. Compared with conventional heating, MW-technology enabled higher loadings of cellulose (2.0 vs. 0.25 wt%) to be processed in a shorter time (20 min instead of 24 h), which is a landmark achievement toward process intensification.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Optimisation of the processing conditions of hydrolytic hydrogenation of cellulose using carbon nanofiber supported Ni catalysts

  • Frecha, E.
  • Remón, J.
  • Torres, D.
  • Suelves, I.
  • Pinilla, J.L.
The synthesis of sorbitol from cellulose over Ni catalysts is a promising valorisation route in the biorefinery scenario, applying relatively simple preparation methods and earth-abundant metals. The overall selectivity, however, depends on the kinetic control of a complex reaction network, involving the hydrolysis of cellulose to monosaccharides via cello-oligomers, glucose hydrogenation into sorbitol and hydrogenolysis side-reactions of sugars and sorbitol to low molecular weight polyols. Therein, subtle changes in the catalyst composition and process conditions might have a strong impact on the final product distribution. Driven by these challenges, this work first-time provides novel insights into the hydrothermal hydrogenation of cellulose over a carbon nanofibre supported Ni catalyst (Ni/CNF). Firstly, the impact of the duration of a ball-milling pre-treatment step and the influences of the hydrothermal time and temperature were thoroughly analysed. The experimental results obtained highlighted the importance of process control to promote the first transformation of cellulose to glucose and its subsequent hydrogenation to sorbitol to minimise the extension of side reactions. Finally, an additional study was conducted to palliate the recalcitrant nature of cellulose by decreasing mass transfer limitations to a minimum extent. This was achieved by including an additional mix-milling of the amorphous cellulose produced in the first pre-treatment with the catalyst and increasing the H2 pressure of the hydrothermal hydrogenation process. This allowed attaining a sorbitol yield as high as 62% at 190 ºC using an initial H2 pressure of 8 MPa for 26 h, which is one of the best results reported in the literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Highly selective catalytic hydrodeoxygenation of guaiacol to benzene in continuous operation mode

  • Gracia, J.
  • Ayala-Cortés, A.
  • Di Stasi, C.
  • Remón, J.
  • Torres, D.
  • Pinilla, J.L.
  • Suelves, I.
Benzene, mostly produced from fossil fuel sources, is an essential chemical to many modern industries. Alternatively to non-renewable methods currently used, the present work explores using fast pyrolysis biomass-derived bio-oils to furnish this valuable platform molecule. Notably, we report for the first time the impact of different operational parameters on the highly selective continuous catalytic hydrodeoxygenation of guaiacol, a bio-oil model compound, into benzene using a Mo2C/CNF-based catalyst. The parametric study includes a first evaluation of the effect of the hydrogen pressure (25, 50 and 75 bar), temperature (300, 325 and 350 °C) and weight hourly space velocity (4 and 10 gorg gcat−1 h−1) on the guaiacol conversion and product distribution, and a subsequent long-term evaluation (30 h on stream) of the catalyst under appropriate processing conditions The experimental results revelated that our Mo2C/CNF was able to achieve a conversion of 90–98% with a relative amount of benzene in the liquid product up to 81% for at least 30 h without any sign of deactivation at 75 bar of H2 and 350 °C, which is a landmark achievement in the conversion of bio-oil derived molecules into platform chemicals.