Pasar al contenido principal

Nuevas técnicas para el desarrollo de componentes RF/microondas. Desarrollo de sensores RF/microndas

IJCI-2017-31339

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Incorporación
Convocatoria Juan de la Cierva Incorporación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD AUTONOMA DE BARCELONA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Reactively-loaded non-periodic slow-wave artificial transmission lines for stop band bandwidth enhancement, application to power splitters

  • Coromina, Jan|||0000-0002-3541-4663
  • Vélez, Paris|||0000-0001-6502-5987
  • Bonache, Jordi|||0000-0002-7225-5737
  • Aznar Ballesta, Francisco|||0000-0002-1845-7071
  • Fernández-Prieto, Armando|||0000-0002-1158-6049
  • Martín, Ferran|||0000-0002-1494-9167
This paper presents slow-wave transmission lines based on non-periodic reactive loading. Specifically, the loading elements are stepped impedance shunt stubs (SISS). By sacrificing periodicity using SISS tuned to different frequencies, multiple transmission zeros above the pass band arise, and the rejection level and bandwidth of the stop band is improved as compared with those of periodic structures. Through a proper design, it is possible to achieve compact lines, simultaneously providing the required electrical length and characteristic impedance at the design frequency (dictated by specifications), and efficiently filtering the response at higher frequencies. These lines are applied to the design of a compact power splitter with filtering capability in this work. The length of the splitter, based on a 35.35 Ω impedance inverter, is reduced by a factor of roughly two. Moreover, harmonic suppression better than 20 dB up to the fourth harmonic is achieved.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Differential-mode to common-mode conversion detector based on rat-race hybrid couplers, analysis and application to differential sensors and comparators

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

An analytical method to implement high-sensitivity transmission line differential sensors for dielectric constant measurements

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Martín, Ferran|||0000-0002-1494-9167
A simple analytical method useful to optimize the sensitivity in differential sensors based on a pair of meandered microstrip lines is presented in this paper. Sensing is based on the phase difference of the transmission coefficients of both lines, when such lines are asymmetrically loaded. The analysis provides the combination of operating frequency and line length (the main design parameters) that are necessary to obtain the maximum possible differential phase (±180°) for a given level of the differential dielectric constant (input dynamic range). The proposed sensor is useful to detect tiny defects of a sample under test (SUT) as compared to a reference (REF) sample. It can also be applied to the measurement of the complex dielectric constant of the SUT, where the real part is inferred from the differential phase, whereas the imaginary part, or the loss tangent, is derived from the modulus of the transmission coefficient of the line loaded with the SUT. It is experimentally demonstrated that the proposed device is able to detect the presence of few and small (purposely generated) defects in a commercial microwave substrate, as well as subtle variations in their density, pointing out the high achieved sensor sensitivity. Sensor validation is also carried out by determining the dielectric constant and loss tangent of commercial microwave substrates.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Signal balancing in unbalanced transmission lines

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Martín, Ferran|||0000-0002-1494-9167
Balanced lines operating as transmission line interconnects are subjected to differential-mode to common-mode conversion (and vice versa) in situations where symmetry imbalances (e.g., caused by line bends) are unavoidable. In this paper, a technique to compensate for such symmetry imbalances, providing pure differential-mode signals at the differential output port of the line, is presented. Such technique uses a rat-race balun (to generate the differential-mode signal) with the isolated port conveniently loaded, and it is based on the modification of the characteristic impedance of one of the unbalanced lines. A detailed analysis that justifies this compensation technique (valid for any arbitrary four-port network) and provides the design equations is presented. The approach is validated through simulation and experiment, by demonstrating that common-mode signals are not transmitted to the differential output port of a bended (i.e., unbalanced) line pair.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Branch line couplers with small size and harmonic suppression based on non-periodic step impedance shunt stub (SISS) loaded lines

  • Coromina, Jan|||0000-0002-3541-4663
  • Vélez, Paris|||0000-0001-6502-5987
  • Bonache, Jordi|||0000-0002-7225-5737
  • Martín, Ferran|||0000-0002-1494-9167
This paper presents branch line couplers with compact size and harmonic suppression based on non-periodic reactively loaded artificial lines. The reactive loading elements of the lines are step impedance shunt stubs (SISSs). Such elements provide transmission zeros, which are useful to efficiently suppressing the harmonic content of the device. Moreover, by virtue of reactive loading, the reported artificial lines exhibit a slow wave effect of interest for device miniaturization. The combination of size, harmonic suppression efficiency, and design simplicity (with a clear design methodology) is of interest within the framework of artificial transmission lines and their application to the optimization of microwave passive components.
Dipòsit Digital de Documents de la UAB
Publicación Artículo de revisión (ReviewArticle)

Planar microwave resonant sensors, a review and recent developments

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Martín, Ferran|||0000-0002-1494-9167
Microwave sensors based on electrically small planar resonant elements are reviewed in this paper. By virtue of the high sensitivity of such resonators to the properties of their surrounding medium, particularly the dielectric constant and the loss factor, these sensors are of special interest (although not exclusive) for dielectric characterization of solids and liquids, and for the measurement of material composition. Several sensing strategies are presented, with special emphasis on differential-mode sensors. The main advantages and limitations of such techniques are discussed, and several prototype examples are reported, mainly including sensors for measuring the dielectric properties of solids, and sensors based on microfluidics (useful for liquid characterization and liquid composition). The proposed sensors have high potential for application in real scenarios (including industrial processes and characterization of biosamples).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Planar Phase-Variation Microwave Sensors for Material Characterization, a review and comparison of various approaches

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Coromina, Jan|||0000-0002-3541-4663
  • Vélez, Paris|||0000-0001-6502-5987
  • Su, Lijuan|||0000-0002-4753-9340
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Martín, Ferran|||0000-0002-1494-9167
Planar phase-variation microwave sensors have attracted increasing interest in recent years since they combine the advantages of planar technology (including low cost, low profile, and sensor integration with the associated circuitry for post-processing and communication purposes, among others) and the possibility of operation at a single frequency (thereby reducing the costs of the associated electronics). This paper reviews and compares three different strategies for sensitivity improvement in such phase-variation sensors (devoted to material characterization). The considered approaches include line elongation (through meandering), dispersion engineering (by considering slow-wave artificial transmission lines), and reflective-mode sensors based on step-impedance open-ended lines. It is shown that unprecedented sensitivities compatible with small sensing regions are achievable with the latter approach.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A Reflective-Mode Phase-Variation Displacement Sensor

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Su, Lijuan|||0000-0002-4753-9340
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Martín, Ferran|||0000-0002-1494-9167
In this paper, a displacement sensor based on an open-ended step-impedance transmission line is reported. The sensor operates in reflection, and the output variable is the phase of the reflection coefficient. The static part of the sensor is the step-impedance transmission line, where the open-ended line section is the sensitive part (sensing line). The movable part is a dielectric slab, e.g., an uncladded microwave substrate. When such slab, located on top of the sensing line, is in relative motion to the line, in the direction of the line axis, the portion of the sensing line covered by the slab varies, and this results in a change in the phase of the reflection coefficient of the line. The step impedance discontinuity contributes to optimize the sensor sensitivity, the key parameter. A detailed analysis providing the design guidelines is carried out and used to design a prototype displacement sensor. The characterization of the fabricated device points out the potential of the approach to implement highly sensitive displacement sensors. The sensor is a one-port device and operates at a single frequency.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

On the Modeling of Microstrip Lines Loaded With Dumbbell Defect-Ground-Structure (DB-DGS) and Folded DB-DGS Resonators

  • Su, Lijuan|||0000-0002-4753-9340
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Martel Villagrán, Jesús|||0000-0002-2705-5912
  • Medina, Francisco|||0000-0002-9947-506X
  • Martín, Ferran|||0000-0002-1494-9167
This paper presents a lumped-element equivalent circuit model of microstrip lines loaded with dumbbell defect-ground-structure (DB-DGS) resonators, etched in the ground plane. The model is valid for ordinary (i.e., unfolded) DB-DGSs, as well as for folded DB-DGSs with an arbitrary aperture angle and relative orientation between the line and the resonator. It is shown that in folded, or partially folded, DB-DGS resonators both magnetic and electric coupling between the line and the resonator should be considered, except for a particular DB-DGS orientation, namely, the one where the symmetry plane of the particle (a magnetic wall) is orthogonal to the line axis. In this case, the particle is exclusively excited by the electric field generated by the line. It is also shown that the circuit model of a microstrip line loaded with an unfolded DB-DGS resonator transversally oriented to the line can be derived from the general model by considering the effects of opening the particle, i.e., a reduction of the electric coupling. In the extreme situation where the DB-DGS is completely opened (unfolded), the electric coupling vanishes, and the particle is exclusively driven by the magnetic field generated by the line. This effect is taken into account in the model by considering that the capacitance between the line and the inner metallic region of the folded, or partially folded, DB-DGS depends on the aperture angle of the particle, and it is null when the particle is unfolded. The models are validated by parameter extraction and comparison of the circuit responses with the responses inferred by electromagnetic simulation and measurement.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly Sensitive Reflective-Mode Phase-Variation Permittivity Sensor Based on a Coplanar Waveguide Terminated With an Open Complementary Split Ring Resonator (OCSRR)

  • Su, Lijuan|||0000-0002-4753-9340
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Martín, Ferran|||0000-0002-1494-9167
This paper presents a one-port reflective-mode phase-variation microwave sensor consisting of a coplanar waveguide (CPW) transmission line terminated with a grounded open complementary split ring resonator (OCSRR). The sensor is useful for measuring the dielectric constant of the so-called material under test (MUT), which should be placed in contact with the OCSRR, the sensitive element. The output variable is the phase of the reflection coefficient. Design guidelines for the implementation of highly sensitive sensors are derived in the paper, and validated through simulation and experiment. As compared to other reflective mode phase-variation sensors based on open-ended sensing lines, the designed and fabricated devices exhibit a very small sensitive region by virtue of the use of an electrically small resonant element, the OCSRR. The relevant figure of merit, defined as the ratio between the maximum sensitivity and the size of the sensing area (expressed in terms of the squared wavelength), is as high as FoM = 5643°/λ 2 in one of the reported prototypes. Moreover, the paper analyzes the effects of losses. From this study, it is concluded that MUT losses do not significantly affect the output variable, provided losses are small. It is also demonstrated that the sensor is useful to estimate the loss tangent of the considered MUT samples.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Microfluidic reflective-mode differential sensor based on open split ring resonators (OSRRs)

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Martín, Ferran|||0000-0002-1494-9167
This paper proposes a differential sensor based on a pair of open split ring resonators (OSRR) operating in reflection. The output signal is thus the differential reflection coefficient of both resonators, intimately related to their dielectric loading. Thus, for identical loads in both sensing resonators, the individual reflection coefficients are equal, thereby providing an ideally null output signal. By contrast, when unequal dielectric loads truncate the symmetry, the reflection coefficients are different, resulting in a differential output signal related to the level of asymmetry. In order to ease the measurement of the output signal, a rat-race hybrid coupler is used. The OSRR sensing loads are connected to the coupled ports of the hybrid coupler, whereas the input signal is injected to the Δ-port, and the output signal is collected at the isolated port (Σ-port). By this means, the output signal, i.e. the differential reflection coefficient between both sensing loads, is obtained from the transmission coefficient of a simple two-port structure. For experimental validation purposes, the sensor is applied to the measurement of isopropanol content in aqueous solutions, and for that purpose, the sensitive regions are equipped with microfluidic channels.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

On the Sensitivity of Reflective-Mode Phase-Variation Sensors Based on Open-Ended Stepped-Impedance Transmission Lines: Theoretical Analysis and Experimental Validation

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Su, Lijuan|||0000-0002-4753-9340
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Martín, Ferran|||0000-0002-1494-9167
This article presents an exhaustive study of the sensitivity in reflective-mode phase-variation sensors based on an open-ended transmission line with a step-impedance discontinuity. Such discontinuity delimits the sensing region (which extends up to the open end of the so-called sensing line), from the transmission line section connected to the input port (design line), which is used to enhance the sensitivity. The theoretical analysis provides the design guidelines to achieve a sensor with high sensitivity compared with the one based on an ordinary (uniform) line with a similar length. In particular, it is shown that for sensitivity optimization, the electrical length of the design line must be set to 90° (or an odd multiple), whereas either a 90° (or an odd multiple) or a 180° (or an even or odd multiple) sensing line can be alternatively used in order to maximize the sensitivity. It is shown that the impedance contrast, defined as the ratio between the characteristic impedances of the design and sensing line, is a key parameter for sensitivity enhancement, and it must be as low or as high as possible for the 90° or 180° sensing lines, respectively. For validation purposes, two prototype devices (one with a 90° and the other one with a 180° sensing line) have been designed and fabricated following the design guidelines. Such devices have been tested by loading the sensing region with several materials with different dielectric constants. Compared with the ordinary line-based sensors, it is found that the maximum sensitivity is enhanced by a factor of 19.7 and 11.4 in the phase-variation sensor based on a 90° and 180° sensing line, respectively. Finally, the sensor concept is generalized to a multisection step-impedance transmission line as a means of further increasing the sensitivity, and a prototype device exhibiting 528.7° maximum sensitivity is implemented.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Differential Sensing Based on Quasi-Microstrip Mode to Slot-Mode Conversion

  • Vélez, Paris|||0000-0001-6502-5987
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Martín, Ferran|||0000-0002-1494-9167
In this letter, a differential sensor and comparator based on a mode conversion detector implemented by means of a slotline resonator is proposed for the first time. The sensor divides the input signal between two identical sensing elements, a pair of microstrip lines loaded with complementary split-ring resonators (CSRRs). Such CSRRs are symmetrically etched in the ground plane at both sides of the slotline. Therefore, by truncating symmetry, e.g., by loading one of the CSRRs with the reference (REF) sample and the other one with the sample under test (SUT), the slot mode is generated in the slotline resonator. The signal level associated with this mode, which can be inferred by means of a slotline/microstrip transition, depends on the level of asymmetry generated by CSRR loading. Consequently, the proposed structure is useful for differential sensing, where a single input and output port suffices to excite the sensor and to measure the output variable, the magnitude of the transmission coefficient.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Single-frequency amplitude-modulation sensor for dielectric characterization of solids and microfluidics

  • Vélez, Paris|||0000-0001-6502-5987
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Ebrahimi, Amir|||0000-0002-1787-2230
  • Herrojo, Cristian|||0000-0003-1934-9993
  • Paredes Marco, Ferran|||0000-0002-7252-1169
  • Scott, James
  • Ghorbani, Kamran|||0000-0001-8767-0207
  • Martín, Ferran|||0000-0002-1494-9167
A microfluidic sensor based on a microstrip line loaded with a composite resonator is reported in this paper. The composite resonator combines a shunt connected step impedance resonator (SIR) and a complementary split ring resonator CSRR) etched in the ground plane. By etching the CSRR beneath the patch of the SIR, the composite CSRR-loaded SIR resonator exhibits two transmission zeros and a pole in between. The operating principle of the sensor is the variation of the transmission coefficient at the pole frequency of the bare resonator, when a material or liquid under test (LUT) is in contact with the CSRR (the sensitive element). By designing the CSRR-loaded SIR resonator with closely spaced pole and transmission zeros, highly sensitive sensors are obtained. Despite the fact that the proposed sensor can also operate as a frequency variation sensor, using it as a single-frequency sensor based on the variation of the transmission coefficient (caused by the LUT) at a specific frequency reduces sensor costs. The reason is that a harmonic signal injected to the input port of the microstrip-based sensor plus a simple amplitude modulation (AM) detector (connected to the output port) suffices for measuring purposes. The proposed microfluidic sensor is applied to the characterization of volume fraction of solutions of isopropanol in deionized (DI) water. The sensor is able to resolve volume fractions as small as 5%, and the maximum measured sensitivity is as good as 4 mV/%.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Characterization of electrolyte content in urine samples through a differential microfluidic sensor based on dumbbell-shaped defected ground structures

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Gil Barba, Marta|||0000-0002-1106-5059
  • José Cunilleras, Eduard|||0000-0002-4536-7717
  • Martín, Ferran|||0000-0002-1494-9167
In this paper, a differential microfluidic sensor and comparator based on a pair of microstrip lines loaded with dumbbell-shaped defected ground structure resonators is applied to the characterization of electrolyte concentration in samples of horse urine. Since variations in the total electrolyte content in urine may be indicative of certain pathologies, the interest is to use the device as a comparator, in order to determine changes in the electrolyte concentration as compared to a reference level. To validate the approach, we have made differential measurements of a set of urine samples with different electrolyte concentrations (which have been previously obtained by means of electrochemical methods). The obtained results correlate with the nominal electrolyte concentrations of the samples, thereby pointing out the potential of the approach as a low-cost pre-screening method (or complementary diagnosis system) to detect potential pathologies or diseases in horses and other animals.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly sensitive defect detectors and comparators exploiting port imbalance in rat-race couplers loaded with step-impedance open-ended transmission lines

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly sensitive phase variation sensors based on step-impedance coplanar waveguide (CPW) transmission lines

  • Su, Lijuan|||0000-0002-4753-9340
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Martín, Ferran|||0000-0002-1494-9167
Reflective-mode step-impedance transmission line based sensors for dielectric characterization of solids or liquids have been recently proposed. In this article, in order to further increase the sensitivity, the sensor is implemented in coplanar waveguide (CPW technology), and this constitutes the main novelty of this work. The sensor thus consists of a high-impedance 90° (or low-impedance 180°) open-ended sensing line cascaded to a low-impedance 90° (or high-impedance 90°) line. The output variable is the phase of the reflection coefficient, which depends on the dielectric constant of the material under test (MUT), the input variable. Placing a MUT on top of the sensing line causes a variation in the effective dielectric constant of the line, thereby modifying the phase of such line. This in turn produces a multiplicative effect on the phase of the reflection coefficient, by virtue of the step-impedance discontinuity. The main advantage of the CPW-based sensor, over other similar sensors based on microstrip technology, is the stronger dependence of the phase velocity of the sensing line with the dielectric constant of the MUT, resulting in sensitivities as high as -45.48° in one of the designed sensors. The sensor is useful for dielectric characterization of solids and liquids, and for the measurement of variables related to changes in the dielectric constant of the MUT (defect detection, material composition, etc.).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Phase-variation microwave sensor for permittivity measurements based on a high-impedance half-wavelength transmission line

  • Su, Lijuan|||0000-0002-4753-9340
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Martín, Ferran|||0000-0002-1494-9167
A phase-variation microwave sensor operating in transmission and implemented by means of a high-impedance half-wavelength sensing line is reported in this paper. The sensor is useful for dielectric constant measurements and dielectric characterization of materials. By forcing the electrical length of the sensing line to be a half-wavelength when it is loaded with the so-called reference (REF) material, perfect matching is obtained regardless of the characteristic impedance of the line. This fact can be used to enhance the sensitivity for small perturbations, by merely increasing the characteristic impedance of the sensing line. An exhaustive analysis that supports such conclusion is reported in the paper. Then, two prototype sensors are designed and fabricated for validation purposes. As compared to the ordinary phase-variation permittivity sensor implemented by means of a matched ( 50-Ω) line with identical length, the sensitivity for small perturbations in the proposed sensor is 2.1 times larger. Further advantages of these sensors are low-cost, small size, implementation in planar technology, and very simple design and fabrication, derived from the fact that the sensing region is a half-wavelength transmission line.