Pasar al contenido principal

Highly sensitive microwave sensors for dielectric characterization, microfluidics, and biosensors

IJC2019-040786-I

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Incorporación
Convocatoria Juan de la Cierva Incorporación
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD AUTONOMA DE BARCELONA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Transmission-Mode Phase-Variation Planar Microwave Sensor Based on a Step-Impedance Shunt Stub for High Sensitivity Defect Detection, Dielectric Constant, and Proximity Measurements

  • Canalias, Xavier|||0009-0002-6473-7514
  • Vélez, Paris|||0000-0001-6502-5987
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Su, Lijuan|||0000-0002-4753-9340
  • Martín, Ferran|||0000-0002-1494-9167
This article proposes a highly sensitive planar microwave sensor able to detect tiny changes in the dielectric constant of the medium surrounding the sensing element or other variables related to it. The sensor is a two-port structure consisting of a step-impedance shunt stub made of a cascade of high/low-admittance inverters (implemented by means of quarter-wavelength transmission line sections) terminated with an open-ended quarter- or half-wavelength resonator (the sensitive element). The sensor operates in transmission, is fed by a harmonic (single-frequency) signal, and uses the phase of the transmission coefficient at the frequency of the feeding signal as the output variable. The achieved sensitivity in the fabricated prototype, in the limit of small perturbations, is Smax = -227.9∘ per unit of dielectric constant variation, and the figure of merit (FoM), defined as the ratio between the maximum sensitivity and the area of the sensing region expressed in guided squared wavelengths, is FoM = 7912°/ λ2 . The sensor is the transmission-mode counterpart of previously reported phase-variation sensors based on one-port reflective-mode structures made of a cascade of inverters terminated with a sensing resonator. The advantage of the proposed sensor over those reflective-mode sensors is the fact that the feeding (input) harmonic signal and the (output) signal containing the relevant (phase) information are present at different ports. This fact eases the measurements in applications where, rather than a vector network analyzer (VNA), a phase detector must be used.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly Sensitive Transmission-Mode Phase-Variation Permittivity Sensor Based on Resonance and Antiresonance

  • Canalias, Xavier|||0009-0002-6473-7514
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Vélez, Paris|||0000-0001-6502-5987
  • Su, Lijuan|||0000-0002-4753-9340
  • Martín, Ferran|||0000-0002-1494-9167
This article presents a strategy for implementing highly sensitive planar microwave permittivity sensors operating in transmission and based on the measurement of the phase of the transmission coefficient at a single frequency. The idea is to shunt-connect a sensitive element to the host line exhibiting a zero (resonance) and a pole (antiresonance) closely spaced. By this means, the phase of the transmission coefficient experiences a significant variation between the zero and the pole, and the sensitivity can be boosted up by tuning the frequency of operation to the pole frequency. The specific implementation consists of a shunt-connected step-impedance resonator (SIR) in parallel with an inductive strip. The effects of coupling between both elements are analyzed in detail. It is shown that such coupling (magnetic) limits the achievable sensitivity. Thus, a method to circumvent such coupling between the SIR and the inductive strip, thereby enhancing the sensitivity, is presented. The maximum sensitivity in the optimized prototype, without coupling, is Smax = -86.18∘, and the figure of merit (FoM), defined as the ratio between Smax and the area of the sensing region expressed in terms of the squared wavelength, is FoM = 17380°/ λ2.
Dipòsit Digital de Documents de la UAB
Publicación Libro o Monografía (Book)

Coupled Structures for Microwave Sensing

  • Martín, Ferran|||0000-0002-1494-9167
This book offers a comprehensive and timely review of planar microwave sensors based on coupled structures. Gathering chapters contributed by the most authoritative researchers on this topic, it presents various strategies for sensor performance optimization using coupled lines, directional couplers, and coupled resonators (either distributed or semi-lumped), focusing mainly on sensitivity optimization, and covering chains of coupled resonators as well. The book also reports on analytical methods, design formulas, sensor validation tests, with both simulation and experimental methods, describing some relevant practical applications. Mainly reflecting the research activity carried out by the different contributors in the last years, this book also includes two introductory chapters to help readers who are not very familiar with microwave sensing technologies and coupled structures. All in all, this book addresses advanced graduate students and researchers involved in microwave and sensor technologies, and may be of interest for engineers and professionals as well, working in areas as diverse as wireless sensors and sensor networks, biosensing, chemical sensing, motion control, microfluidics, Internet of Things (IoT), and smart systems.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Planar Phase-Variation Microwave Sensors for Material Characterization, a review and comparison of various approaches

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Coromina, Jan|||0000-0002-3541-4663
  • Vélez, Paris|||0000-0001-6502-5987
  • Su, Lijuan|||0000-0002-4753-9340
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Martín, Ferran|||0000-0002-1494-9167
Planar phase-variation microwave sensors have attracted increasing interest in recent years since they combine the advantages of planar technology (including low cost, low profile, and sensor integration with the associated circuitry for post-processing and communication purposes, among others) and the possibility of operation at a single frequency (thereby reducing the costs of the associated electronics). This paper reviews and compares three different strategies for sensitivity improvement in such phase-variation sensors (devoted to material characterization). The considered approaches include line elongation (through meandering), dispersion engineering (by considering slow-wave artificial transmission lines), and reflective-mode sensors based on step-impedance open-ended lines. It is shown that unprecedented sensitivities compatible with small sensing regions are achievable with the latter approach.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Parametric analysis of the edge capacitance of uniform slots and application to frequency-variation permittivity sensors

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Martel Villagrán, Jesús|||0000-0002-2705-5912
  • Vélez, Paris|||0000-0001-6502-5987
  • Medina, Francisco|||0000-0002-9947-506X
  • Su, Lijuan|||0000-0002-4753-9340
  • Martín, Ferran|||0000-0002-1494-9167
This paper presents a parametric analysis relative to the effects of the dielectric constant of the substrate, substrate thickness and slot width on the edge capacitance of a slot-based resonator. The interest is to find the conditions (ranges of the previously cited parameters) compatible with the presence of a quasi-magnetic wall in the plane of the slot (or plane of the metallization). If such magnetic wall is present (or roughly present), the electric field in the plane of the slot is tangential (or quasi-tangential) to it and the edge capacitance can be considered to be the parallel combination of the capacitances at both sides of the slot. Moreover, variations in one of such capacitances, e.g., caused by a change in the material on top of the slot, or by a modification of the dielectric constant of the substrate do not affect the opposite capacitance. Under the magnetic wall approximation, the capacitance of certain electrically small slot-based resonators can be easily linked to the dielectric constant of the material present on top of it. The consequence is that such resonators can be used as sensing elements in a permittivity sensor and the dielectric constant of the so-called material under test (MUT) can be determined from the measured resonance frequency and a simple analytical expression. In this paper, the results of this parametric analysis are validated by considering several sensing structures based on dumbbell defect ground structure (DB-DGS) resonators of different dimensions.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Discussion and analysis of dumbbell defect-ground-structure (DB-DGS) resonators for sensing applications from a circuit theory perspective

  • Su, Lijuan|||0000-0002-4753-9340
  • Vélez, Paris|||0000-0001-6502-5987
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Martín, Ferran|||0000-0002-1494-9167
Microstrip transmission lines loaded with dumbbell defect-ground-structure (DB-DGS) resonators transversally oriented have been exhaustively used in microwave circuits and sensors. Typically, these structures have been modelled by means of a parallel LC resonant tank series connected to the host line. However, the inductance and capacitance of such model do not have a physical meaning, since this model is inferred by transformation of a more realistic model, where the DB-DGS resonator, described by means of a resonant tank with inductance and capacitance related to the geometry of the DB-DGS, is magnetically coupled to the host line. From parameter extraction, the circuit parameters of both models are obtained by considering the DB-DGS covered with semi-infinite materials with different dielectric constant. The extracted parameters are coherent and re-veal that the general assumption of considering the simple LC resonant tank series-connected to the line to describe the DB-DGS-loaded line is reasonable with some caution. The implications on the sensitivity, when the structure is devoted to operating as a permittivity sensor, are discussed.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

On the Modeling of Microstrip Lines Loaded With Dumbbell Defect-Ground-Structure (DB-DGS) and Folded DB-DGS Resonators

  • Su, Lijuan|||0000-0002-4753-9340
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Martel Villagrán, Jesús|||0000-0002-2705-5912
  • Medina, Francisco|||0000-0002-9947-506X
  • Martín, Ferran|||0000-0002-1494-9167
This paper presents a lumped-element equivalent circuit model of microstrip lines loaded with dumbbell defect-ground-structure (DB-DGS) resonators, etched in the ground plane. The model is valid for ordinary (i.e., unfolded) DB-DGSs, as well as for folded DB-DGSs with an arbitrary aperture angle and relative orientation between the line and the resonator. It is shown that in folded, or partially folded, DB-DGS resonators both magnetic and electric coupling between the line and the resonator should be considered, except for a particular DB-DGS orientation, namely, the one where the symmetry plane of the particle (a magnetic wall) is orthogonal to the line axis. In this case, the particle is exclusively excited by the electric field generated by the line. It is also shown that the circuit model of a microstrip line loaded with an unfolded DB-DGS resonator transversally oriented to the line can be derived from the general model by considering the effects of opening the particle, i.e., a reduction of the electric coupling. In the extreme situation where the DB-DGS is completely opened (unfolded), the electric coupling vanishes, and the particle is exclusively driven by the magnetic field generated by the line. This effect is taken into account in the model by considering that the capacitance between the line and the inner metallic region of the folded, or partially folded, DB-DGS depends on the aperture angle of the particle, and it is null when the particle is unfolded. The models are validated by parameter extraction and comparison of the circuit responses with the responses inferred by electromagnetic simulation and measurement.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly Sensitive Reflective-Mode Phase-Variation Permittivity Sensor Based on a Coplanar Waveguide Terminated With an Open Complementary Split Ring Resonator (OCSRR)

  • Su, Lijuan|||0000-0002-4753-9340
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Martín, Ferran|||0000-0002-1494-9167
This paper presents a one-port reflective-mode phase-variation microwave sensor consisting of a coplanar waveguide (CPW) transmission line terminated with a grounded open complementary split ring resonator (OCSRR). The sensor is useful for measuring the dielectric constant of the so-called material under test (MUT), which should be placed in contact with the OCSRR, the sensitive element. The output variable is the phase of the reflection coefficient. Design guidelines for the implementation of highly sensitive sensors are derived in the paper, and validated through simulation and experiment. As compared to other reflective mode phase-variation sensors based on open-ended sensing lines, the designed and fabricated devices exhibit a very small sensitive region by virtue of the use of an electrically small resonant element, the OCSRR. The relevant figure of merit, defined as the ratio between the maximum sensitivity and the size of the sensing area (expressed in terms of the squared wavelength), is as high as FoM = 5643°/λ 2 in one of the reported prototypes. Moreover, the paper analyzes the effects of losses. From this study, it is concluded that MUT losses do not significantly affect the output variable, provided losses are small. It is also demonstrated that the sensor is useful to estimate the loss tangent of the considered MUT samples.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly sensitive defect detectors and comparators exploiting port imbalance in rat-race couplers loaded with step-impedance open-ended transmission lines

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Circuit Analysis of a Coplanar Waveguide (CPW) Terminated With a Step-Impedance Resonator (SIR) for Highly Sensitive One-Port Permittivity Sensing

  • Casacuberta, Pau|||0000-0002-2658-2200
  • Vélez, Paris|||0000-0001-6502-5987
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Su, Lijuan|||0000-0002-4753-9340
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Ebrahimi, Amir|||0000-0002-1787-2230
  • Martín, Ferran|||0000-0002-1494-9167
This paper presents a single-frequency reflective-mode phase-variation microwave sensor devoted to the dielectric characterization of materials. The device is implemented in coplanar waveguide (CPW) technology and consists of two parts: (i) the sensing region, a step-impedance resonator (SIR) as termination of a CPW transmission line, and (ii) the design region, a cascade of high/low impedance quarter-wavelength inverters, used to boost up the sensitivity. By placing the so-called material under test (MUT) on top of the sensing region, the capacitance of the SIR is altered due to the effects of the dielectric constant of the MUT. This modifies the phase of the reflection coefficient seen from the input port, the output variable. From a circuit analysis, it is demonstrated that the sensitivity for small perturbations in the vicinity of the dielectric constant of a reference (REF) material can be optimized by setting the operation frequency of the sensor to the resonance frequency of the SIR loaded with such REF material. The maximum sensitivity in one of the reported sensors is as high as 66.5°, and the main figure of merit, defined as the ratio between the maximum sensitivity and the area of the sensing region expressed in terms of the squared guided wavelength, is FoM=3643∘/λ2 . Such figure of merit represents a significant improvement as compared to the one of the equivalent sensor implemented by means of an open-ended quarter-wavelength sensing line. Such equivalence between the semi-lumped element (i.e., SIR-based) sensor and the fully distributed counterpart is also analyzed in the paper.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Portable Reflective-Mode Phase-Variation Microwave Sensor Based on a Rat-Race Coupler Pair and Gain/Phase Detector for Dielectric Characterization

  • Vélez, Paris|||0000-0001-6502-5987
  • Paredes Marco, Ferran|||0000-0002-7252-1169
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Elgeziry, Mahmoud|||0000-0002-2801-2826
  • Su, Lijuan|||0000-0002-4753-9340
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Costa, Filippo|||0000-0001-7572-2014
  • Genovesi, Simone|||0000-0002-5323-1780
  • Martín, Ferran|||0000-0002-1494-9167
This article presents a low-cost and portable phase-variation planar microwave sensor operating in reflective mode, where the output variable, the phase of the reflection coefficient of the one-port sensing element, is retrieved by means of a distributed circuit based on a pair of rat-race hybrid couplers and the associated electronics. This includes a microcontroller, a voltage controlled oscillator (VCO), a digital-to-analog converter (DAC), and an RF/microwave gain/phase detector. By this means, vector network analyzers (VNAs), i.e., high-cost instruments typically used for obtaining the reflection coefficient in one-port structures or circulators (microwave components able to separate the injected signal from the reflected signal in any one-port network) are avoided. Indeed, the presented architecture (including the microwave rat-race hybrid configuration and the associated electronics) can be adapted to other one-port reflective-mode phase-variation microwave sensors. A prototype example, where the sensing element is a one-port step-impedance open-ended transmission line, is reported. The device provides the phase of the reflection coefficient of the sensing element as a function of the dielectric constant of the material under test (MUT) with a maximum sensitivity of -65.7° and a relative error of less than 8% in all the measurements.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Microwave Humidity Sensor for Early Detection of Sweat and Urine Leakage

  • Su, Lijuan|||0000-0002-4753-9340
  • Vélez, Paris|||0000-0001-6502-5987
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Martín, Ferran|||0000-0002-1494-9167
A planar microwave sensor devoted to the detection of humidity in underwear and clothes in general is proposed. The ultimate goal of the sensor is to detect the presence of liquids in fabrics, which is of interest to aid patients who suffer from certain pathologies, such as hyperhidrosis and enuresis. The main target in the design of the sensor, considering the envisaged application, is simplicity. Thus, the sensor operates at a single frequency, and the working principle is the variation in the magnitude of the transmission coefficient of a matched line loaded with an open-ended quarter-wavelength sensing stub resonator. The stub, which must be in contact with the so-called fabric under test (FUT), generates a notch in the transmission coefficient with a resonance frequency that depends on the humidity level of the fabric. By designing the stub with a moderately high-quality factor, the variation in the resonance frequency causes a significant change in the magnitude level at the operating frequency, which is the resonance frequency when the sensing stub is loaded with the dry fabric, and the presence of liquid can be detected by means of an amplitude detector. A prototype device is proposed and experimentally validated. The measured change in the magnitude level by simply depositing one 50 μL drop of water in the FUT is roughly 25 dB.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly sensitive reflective-mode phase-variation permittivity sensors using coupled line sections

  • Casacuberta, Pau|||0000-0002-2658-2200
  • Vélez, Paris|||0000-0001-6502-5987
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Su, Lijuan|||0000-0002-4753-9340
  • Martín, Ferran|||0000-0002-1494-9167
Highly sensitive permittivity sensors operating in reflection and exploiting phase variation are presented in this article. The sensors are one-port structures implemented by means of a pair of coupled lines, the sensitive region, with an appropriate termination. In particular, it is demonstrated that by either short-circuiting the crossed port to the input port of the device (opening the remaining two ports), or opening the crossed port to the input port (terminating the other two ports with a short-circuit), the sensitivity can be driven to very high values, controlled by the coupling factor. For that purpose, the electrical length of the pair of coupled lines must be set to 90° when such lines are loaded with the reference (REF) material. Thus, the sensitivity is optimized for dielectric constants (the input variable) in the vicinity of the dielectric constant of the REF material, where the indicated phase condition is fulfilled. The output variable is the phase of the reflection coefficient, an easily measurable quantity. For validation purposes, three prototype sensors are designed and fabricated. The achieved sensitivities in two of the fabricated sensors are as high as 659.6° and 736.0°, with figures of merit (FoMs), or ratio between the maximum sensitivity and the area of the sensing region expressed in terms of the squared-wavelength, of FoM.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Losses Assisted Sensitivity Enhancement in Reflective-Mode Phase-Variation Permittivity Sensors Based on Weakly Coupled Distributed Resonators

  • Casacuberta, Pau|||0000-0002-2658-2200
  • Vélez, Paris|||0000-0001-6502-5987
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Su, Lijuan|||0000-0002-4753-9340
  • Martín, Ferran|||0000-0002-1494-9167
This letter demonstrates that losses [including substrate losses and losses in the material under test (MUT)] can be beneficial to boost the sensitivity in one-port reflective-mode phase-variation planar permittivity sensors based on a pair of weakly coupled quarter-wavelength resonators (the sensing elements). It is shown that the key aspect of optimizing the sensitivity in the limit of small perturbations of the dielectric constant of the MUT in the vicinity of the reference dielectric constant is to achieve a high slope in the phase of the reflection coefficient at the operating frequency and the output variable. Depending on the level of losses, such phase slope can be either negative (low-loss regime) or positive (high-loss regime). Nevertheless, the relevant aspect is that, regardless of its sign, the magnitude of the phase slope can be arbitrarily high by adequately designing the sensor considering the device and MUT losses. Thus, losses do not necessarily degrade sensitivity; instead, they can be strategically utilized to achieve unprecedented sensitivities in this type of sensor, which operates based on the measurement of the reflection coefficient phase.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Phase-variation microwave sensor for permittivity measurements based on a high-impedance half-wavelength transmission line

  • Su, Lijuan|||0000-0002-4753-9340
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Martín, Ferran|||0000-0002-1494-9167
A phase-variation microwave sensor operating in transmission and implemented by means of a high-impedance half-wavelength sensing line is reported in this paper. The sensor is useful for dielectric constant measurements and dielectric characterization of materials. By forcing the electrical length of the sensing line to be a half-wavelength when it is loaded with the so-called reference (REF) material, perfect matching is obtained regardless of the characteristic impedance of the line. This fact can be used to enhance the sensitivity for small perturbations, by merely increasing the characteristic impedance of the sensing line. An exhaustive analysis that supports such conclusion is reported in the paper. Then, two prototype sensors are designed and fabricated for validation purposes. As compared to the ordinary phase-variation permittivity sensor implemented by means of a matched ( 50-Ω) line with identical length, the sensitivity for small perturbations in the proposed sensor is 2.1 times larger. Further advantages of these sensors are low-cost, small size, implementation in planar technology, and very simple design and fabrication, derived from the fact that the sensing region is a half-wavelength transmission line.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Reflective-mode phase-variation submersible sensor for liquid characterization

  • Su, Lijuan|||0000-0002-4753-9340
  • Vélez, Paris|||0000-0001-6502-5987
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Gil Barba, Marta|||0000-0002-1106-5059
  • Martín, Ferran|||0000-0002-1494-9167
A one-port reflective-mode microwave submersible sensor based on an open-ended step-impedance microstrip line configuration, operating at a single frequency, useful for the dielectric characterization of liquids and the measurement of liquid composition in binary mixtures, is proposed in this article. The sensor constitutes two parts, namely, the microwave module, including the sensitive region, and a 3-D-printed case (made of polylactic acid-PLA), necessary for sealing, thus preventing from any liquid leakage to the nonsensing regions of the microwave module. To enhance the sensitivity, the open-ended line Section of the microwave module, i.e., the sensing region in contact with the liquid under test (LUT), is a quarter wavelength microstrip line with high impedance. Thus, the phase of the reflection coefficient is the output variable, highly dependent on the input variable-the dielectric constant of the LUT placed directly above the sensing region. In order to validate the sensing structure, a prototype device has been designed and fabricated. The average sensitivity to variations in the concentration of ethanol in solutions of deionized (DI) water is 1.22°/%, and sensor resolution is 2%. The fabricated sensor is resistant to liquid leakage, and therefore, it can be completely submerged for measuring purposes, acting as an effective measuring probe.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Reflective-Mode Phase-Variation Permittivity Sensor Based on a Step-Impedance Microstrip Line Terminated With a Slot Resonator for Solid and Liquid Characterization

  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Vélez, Paris|||0000-0001-6502-5987
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Su, Lijuan|||0000-0002-4753-9340
  • Martín, Ferran|||0000-0002-1494-9167
This article proposes a highly sensitive single-frequency microwave sensor for dielectric characterization of solids and liquids. The sensor is a reflective-mode one-port device consisting of a step-impedance microstrip line terminated with a slot resonator (the sensing element) transversely etched on the ground plane. The working principle of the sensor is the variation experienced by the phase of the reflection coefficient at the operating frequency as a consequence of changes in the dielectric properties (dielectric constant) of the material under test (MUT), either a solid or a liquid, which should be in contact with the slot resonator. A relevant advantage of the reported sensor is the fact that the MUT is located in the back substrate side of the microstrip structure. Therefore, any potential interaction between the MUT, including the mechanic holder used for liquid sensing, and the microstrip line, is prevented. A detailed sensitivity analysis that considers the effects of losses is carried out. It is concluded that, depending on the losses of the MUT, there are two different sensor operation regimes (the low-loss and the high-loss regimes), with unequal behavior, but both are useful to sensitively detect changes in the dielectric properties of the MUT. The maximum sensitivity in the prototype device devoted to the measurement of the dielectric constant in low-loss solid samples is 255.5 ∘. In the liquid sensor, equipped with a 3-D-printed holder, and focused in this article on the detection of small volume fractions of isopropanol in deionized (DI) water, the maximum sensitivity is 64.96 ∘ /%.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Effects of losses on the sensitivity of reflective-mode phase-variation liquid sensors

  • Vélez, Paris|||0000-0001-6502-5987
  • Canalias, Xavier|||0009-0002-6473-7514
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Casacuberta, Pau|||0000-0002-2658-2200
  • Su, Lijuan|||0000-0002-4753-9340
  • Martín, Ferran|||0000-0002-1494-9167
This article is focused on the analysis of the effects of losses on the sensitivity of reflective-mode phase-variation liquid sensors implemented by means of an open-ended (either quarter-wavelength or half-wavelength) transmission line distributed resonator (the sensing element) cascaded to a set of high/low impedance inverters (implemented by means of quarter-wavelength line sections). The device operates at a single frequency, and the working principle is the variation of the phase of the reflection coefficient (the output variable) caused by changes in the dielectric properties of the material under test (MUT), a liquid in this study. Since liquids are lossy samples, it is expected that the sensitivity of the sensor is influenced by losses, an aspect demonstrated in this article. It is shown that two operation regimes can be distinguished: 1) the low-loss regime, where the sensitivity is influenced by MUT losses, but the behavior is similar to the one of the lossless case and 2) the high-loss regime, where losses not only play a key role on the sensitivity but also modify the dependence of the output variable with the dielectric constant of the liquid under consideration compared to the lossless case. Nevertheless, contrary to general belief, with an adequate sensor design, losses might be beneficial in order to boost the sensitivity in the limit of small perturbations (this is the main contribution of this article). Validation is carried out by considering different types of oil samples and various sensing devices operating either in the low-loss regime or the high-loss regime.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly Sensitive Coplanar Waveguide (CPW) reflective-mode phase-variation permittivity sensors based on weakly coupled Step-Impedance Resonators (SIRs)

  • Casacuberta, Pau|||0000-0002-2658-2200
  • Vélez, Paris|||0000-0001-6502-5987
  • Muñoz Enano, Jonathan|||0000-0003-1271-3801
  • Su, Lijuan|||0000-0002-4753-9340
  • Martín, Ferran|||0000-0002-1494-9167
This article presents a small-sized and highly sensitive planar microwave permittivity sensor based on a pair of weakly coupled step-impedance resonators (SIRs), the sensing elements. The sensor, a one-port structure, is implemented in coplanar waveguide (CPW) technology, and it operates in the reflection mode. The sensing principle is the variation in the phase of the reflection coefficient at the operating frequency, the output variable, caused by the changes in the dielectric constant of the material under test (MUT). This article demonstrates that the maximum sensitivity is inversely proportional to the square of the electric coupling coefficient between the sensing SIRs. Thus, the sensitivity can be unprecedentedly enhanced by merely separating enough the coupled SIRs (thereby reducing their mutual coupling). Since the sensing area is circumscribed to the region occupied by the square (capacitive) patches of the SIRs, it follows that the proposed sensor exhibits also a very high figure of merit ( FoM=26551∘/λ2 ), or ratio between the maximum sensitivity and the size of the sensing area expressed in terms of the squared guided wavelength, λ2.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly sensitive lossy tunable permittivity sensor

  • Casacuberta, Pau|||0000-0002-2658-2200
  • Vélez, Paris|||0000-0001-6502-5987
  • Su, Lijuan|||0000-0002-4753-9340
  • Canalias, Xavier|||0009-0002-6473-7514
  • Martín, Ferran|||0000-0002-1494-9167
This letter presents a novel lossy tunable permittivity sensor that enhances sensitivity through a controllable conductivity method using a junction field-effect transistor (JFET) in the ohmic region. The sensor, a one-port reflective-mode device, includes a coplanar waveguide (CPW) ending in a step impedance resonator (SIR) as the sensing element, with the JFET bridging the SIR patch and ground. The high sensitivity is achieved by virtue of the strong shift in the phase of the reflection coefficient at resonance experienced by varying the dielectric constant of the material under test (MUT). This device not only serves as a permittivity sensor but also for tracking variables linked to permittivity changes. Our experimental results uniquely demonstrate that sensitivity to minute perturbations can be significantly enhanced by tuning losses. The prototype, designed and constructed for detecting submillimeter proximity changes with a dielectric slab, achieves a peak sensitivity of 2291°/mm within a compact 8.5×12 -mm footprint.