Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Aromatic poly(ether ether ketone)s capable of crosslinking via UV irradiation to improve gas separation performance

  • Puertas-Bartolomé, María
  • Dose, M. E.
  • Bosch, Paula
  • Freeman, Benny D.
  • McGrath, J. E.
  • Riffle, J. S.
  • Lozano López, Ángel Emilio
  • González de la Campa, José
  • Álvarez, Cristina
The effect of UV-crosslinking on the gas transport properties of two poly(ether ether ketone)s derived from difluorobenzophenone and two bisphenol derivatives, with four (TMBP-DFB) or six (HMBP-DFB) methyl groups, has been studied. The crosslinking reaction was conducted on dense membranes, using polychromatic light, with wavelengths higher than 350 nm, at room temperature and in presence of air. Both polymers were able to produce crosslinked membranes, with gel fractions close to 75%, but a shorter irradiation time was required for HMBP-DFB. A DFT quantum mechanical study has stated that HMBP-DFB radical formation is much easier than for TMBP-DFB, which would support the fastest kinetics of the crosslinking process for HMBP-DFB. The crosslinked membranes have shown greatly improved gas transport properties, especially for the O2/N2 gas pair, where the Robeson upper bound line of 1991 was clearly surpassed. The improvement in selectivity has been ascribed to the better molecular-sieving characteristics of crosslinked membranes, We acknowledge the Financial support provided by MINECO (MAT2013-45071-R, CTQ2012-31076 and MAT2016-76413-C2- R2) and by the National Science Foundation under grant number IIP-1237857. Authors wish to thank Judit González for helping with the characterization of polymers, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis, characterization and gas separation properties of novel polyimides containing cardo and tert-butyl-m-terphenyl moieties

  • Bermejo, L. A.
  • Álvarez, Cristina
  • Maya, Eva M.
  • García Sánchez, Carolina
  • González de la Campa, José
  • Lozano López, Ángel Emilio
series of aromatic polyimides has been obtained by the reaction of two dianhydrides, the commercial 2,2'- bis(3,4-dicarboxyphenyl)hexafluoropropane dianhydride (6FDA) and another having a 5'-tert-butyl-m-terphenyl moiety (BTPDA), with several diamines, including two that have a cardo structure (derived from 9H-fluorene), one of them bearing methyl groups ortho to the amino functionalities (TMeCardo). The solubility, and also the thermal, mechanical, and gas separation properties of the corresponding polyimide membranes were evaluated and compared in order to explore the effect of the different groups in the polyimide backbone. The novel polyimides, which were derived from BTPDA and the cardo diamines, showed high thermal stability, excellent solubility in organic solvents and good gas separation properties, especially the polyimide that bore the ortho methyl substituents. The behavior was especially good for the pair O/N, where the TMeCardo polymer overpassed the Robeson upper bound., The financial support of this work by the Spanish Ministry of Economy and Competitiveness (MINECO) (MAT2013- 45071, CTQ2013-48406-P, MAT2016-76413-C2-R2) is greatly appreciated., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermally rearranged polybenzoxazoles made from poly(orthohydroxyamide)s. Characterization and evaluation as gas separation membranes

  • Díez, Blanca
  • Cuadrado, Purificación
  • Marcos-Fernández, Ángel
  • González de la Campa, José
  • Tena, Alberto
  • Prádanos, Pedro
  • Palacio, Laura
  • Moo Lee, Young
  • Álvarez, Cristina
  • Lozano López, Ángel Emilio
  • Hernández, Antonio
Two series of aromatic poly(ortho-hydroxyamide)s (poly(o-hydroxyamide)s, HPAs) were prepared by reaction of two diamines, 2,2-bis(3-amino-4-hydroxyphenyl) propane (APA) and 2,2-bis(3-amino-4-hydroxyphenyl) hexafluoropropane (APAF), with four aromatic diacid chlorides; terephthaloyl dichloride (TPC), isophthaloyl dichloride (IPC), 2,2-bis[4-chlorocarbonylphenyl)hexafluoropropane (6FC) and 4,4¿-sulfonyldibenzoyl dichloride (DBSC). Amorphous HPAs with high molecular weights (inherent viscosities higher than 0.5 dL/g) and relatively high glass transition temperatures (220¿280 °C) were obtained. Dense membranes of HPAs were able to undergo a thermal rearrangement (TR) process to polybenzoxazoles (ß-TR-PBOs) heating at moderate temperatures (between 250 and 375 °C), and their complete conversion was reached at a temperature below 375 °C, depending on the o-hydroxy diamine moiety, APA and APAF. The ß-TR-PBOs films derived from APAF showed a higher thermal stability and higher Tg than those from APA. Gas separation properties of TR-PBOs membranes were superior to those of their poly(o-hydroxyamide) precursors, particularly for the following gas pairs: O2/N2, CO2/CH4, He/CH4 and He/CO2., The financial support provided, by the Spain's MINECO (MAT2013- 45071-R and MAT2016-76413-C2-1-R and MAT2016-76413-C2-2-R AEI/FEDER, UE and CTQ 2012-31076) is greatly acknowledged. This research was also supported by the Korea Carbon Capture & Sequestration R&D Center (KCRC) through the National Research Foundation of Korea (NRF) funded by the Ministry of Science, ICT, and Future Planning (NRF-2014M1A8A1049305). We are also indebted to the Spanish Junta de Castilla y León for its funding help (project VA248U13). Authors kindly acknowledge Sara Rodriguez for carrying out the gas separation tests and Judit González Jarillo for performing polymer characterization, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Porous bidentate polyimines as ligands for transition metals: catalysts for transfer hydrogenation of furfural

  • Maya, Eva M.
  • Campa, José G. de la
  • Iglesias, Marta
Poster presented at the 1st European Conference on Metal Organic Frameworks and Porous Polymers, held on October 11-14th, 2015, Potsdam (Germany)., In 2009, Uribe-Romo et al.1 reported a new class of materials, porous polyimines, by reacting a dialdehyde and a tetraamine. These materials are rich nitrogen-polymers with potential applications such as gas storage or catalysis. In fact Verde et al.2 probed the excellent catalytic properties of Cu and Ir- porous polyimines. In this work we report the preparation of porous bidentate polyimines by reacting a trior a tetraamine with pyridine-2,6-dicarbaldehyde. These polyimines can act as bidentate ligands and coordinate to transition metals leading to a new family of heterogenized transition metal catalyst; now, we have incorporate Fe(II) to obtain ThPyFe and C3vPyFe (Figure 1) and have been used as catalysts in the transfer hydrogenation (TH) of furfural. Furfural (F) is a highly reactive aldehyde which causes the unstabilty of crude bio-oil. Thus the transformation of F is required for improving the bio-oil as substitute for diesel. The TH of F produces mainly furfuryl alcohol (FA) and traces of the corresponding furfuryl ether (FE). We found that minimal amounts (0.1% weight respect to F) of Fe-bidentate porous polyimines are able to transform F completely in a single product, FE, in short times (TOF values up to 1100 h-1) using 1-butanol as a source of hydrogen and 120°C. The complex ThPyFe was reused under the same conditions, maintaining the activity for at least seven runs (100% of F conversion, 100% yield in FE formation)., Projects MAT2013-45071 and Consolider-Ingenio 2010-(CSD-0050-MULTICAT).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Insight into ETS-10 synthesis for the preparation of mixed matrix membranes for CO2/CH4 gas separation

  • Sorribas, S.
  • Comesaña-Gándara, B.
  • Lozano, A.E.
  • Zornoza, B.
  • Téllez, C.
  • Coronas, J.
An in-depth study into the synthesis of the titanosilicate ETS-10 has been carried out to obtain crystals with different particle sizes, roughness and porosity. The effect of these parameters on the CO2/CH4 gas separation performance using mixed matrix membranes (MMMs) has been studied. MMMs based on ETS-10 polycrystalline particles of 1-2 µm in size with high surface roughness and porosity gave rise to a good filler dispersion and filler-polymer interaction. The addition of 10 wt% ETS-10 polycrystalline particles into the polysulfone matrix increased the CO2 permeability from 6.1 to 7.8 Barrer and the CO2/CH4 selectivity from 31 to 38. When using the polyimide 6FDA-6FpDA, a glassy polymer with high gas permeability, the addition of 10 wt% ETS-10 polycrystalline particles increased the CO2 permeability from 96 to 125 Barrer, with a decrease in CO2/CH4 selectivity from 56 to 51.