Pasar al contenido principal

CAPAS FINAS DE PEROVSKITA CON CONTACTOS SELECTIVOS DE ELECTRONES PARA CONVERSION FOTOVOLTAICA, MODELOS Y CARACTERIZACION (UPO)

MAT2013-47192-C3-3-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSIDAD PABLO DE OLAVIDE, DE SEVILLA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The interaction between hybrid organic-inorganic halide perovskite and selective contacts in perovskite solar cells: An infrared spectroscopy study

  • Idígoras, J.
  • Todinova, A.
  • Sánchez-Valencia, J. R.
  • Barranco, Ángel
  • Borrás, Ana
  • Anta, J. A.
The interaction of hybrid organic-inorganic halide perovskite and selective contacts is crucial to get efficient, stable and hysteresis-free perovskite-based solar cells. In this report, we analyze the vibrational properties of methylammonium lead halide perovskites deposited on different substrates by infrared absorption (IR) measurements (4000-500 cm). The materials employed as substrates are not only characterized by different chemical natures (TiO, ZnO and AlO), but also by different morphologies. For all of them, we have investigated the influence of these substrate properties on perovskite formation and its degradation by humidity. The effect of selective-hole contact (Spiro-OmeTad and P3HT) layers on the degradation rate by moisture has also been studied. Our IR results reveal the existence of a strong interaction between perovskite and all ZnO materials considered, evidenced by a shift of the peaks related to the N-H vibrational modes. The interaction even induces a morphological change in ZnO nanoparticles after perovskite deposition, pointing to an acid-base reaction that takes place through the NH groups of the methylammonium cation. Our IR and X-ray diffraction results also indicate that this specific interaction favors perovskite decomposition and PbI formation for ZnO/perovskite films subjected to humid conditions. Although no interaction is observed for TiO, AlO, and the hole selective contact, the morphology and chemical nature of both contacts appear to play an important role in the rate of degradation upon exposure to moisture., We thank the Regional Government of Andalusia for financial support via grants FQM1851 and FQM2310 and Ministerio de Economia y Competitividad under grants MAT2013-47192-C3-3-R and MAT2013-42900-P. MINECO/ICTI2013-2016/MAT2013-42900-P
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Impact of moisture on efficiency-determining electronic processes in perovskite solar cells

  • Salado, Manuel
  • Contreras-Bernal, Lidia
  • Calió, Laura
  • Todinova, Anna
  • López-Santos, Carmen
  • Ahmad, Shahzada
  • Borrás, Ana
  • Idígoras, Jesús
  • Anta, Juan A.
Moisture-induced degradation in perovskite solar cells was thoroughly investigated by structural (SEM, EDS, XRD and XPS) and device characterization (impedance and intensity modulated photocurrent spectroscopy) techniques. Both the influence of the perovskite composition and the nature of the hole selective material were analyzed. The degradation rate was found to be significantly slower for mixed perovskites and P3HT-based devices. However, for a fixed degradation degree (defined as a 50% drop from the initial photocurrent), all configurations show similar features in small-perturbation analysis. Thus, a new mid-frequency signal appears in the impedance response, which seems to be related to charge accumulation at the interfaces. In addition, faster recombination, with a more important surface contribution, and slower transport were clearly inferred from our results. Both features can be associated with the deterioration of the contacts and the formation of a higher number of grain boundaries., We thank Junta de Andalucía for financial support via grant FQM 1851 and FQM 2310. We thank the Ministerio de Economía y Competitividad of Spain (MAT2013-47192-C3-3-R and MAT2016-76892-C3-2-R) and the EU through the Cohesion Fund and FEDER programs (MAT2013-42900-P and MAT2016-79866-R) for financial support and Red de Excelencia “Emerging photovoltaic Technologies”. SA and LC are thankful for the “Thinface” project from the European Union Seventh Framework Programme, under grant agreement no. 607232, for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The role of surface recombination on the performance of perovskite solar cells: effect of morphology and crystalline phase of TiO2 contact

  • Idígoras, Jesús
  • Contreras-Bernal, Lidia
  • Cave, James M.
  • Courtier, Nicola E.
  • Barranco, Ángel
  • Borrás, Ana
  • Sánchez-Valencia, J. R.
  • Anta, Juan A.
  • Walker, Alison B.
Herein, the preparation of 1D TiO nanocolumnar films grown by plasma-enhanced chemical vapor deposition is reported as the electron selective layer (ESL) for perovskite solar devices. The impact of the ESL architecture (1D and 3D morphologies) and the nanocrystalline phase (anatase and amorphous) is analyzed. For anatase structures, similar power conversion efficiencies are achieved using an ESL either the 1D nanocolumns or the classical 3D nanoparticle film. However, lower power conversion efficiencies and different optoelectronic properties are found for perovskite devices based on amorphous 1D films. The use of amorphous TiO as electron selective contact produces a bump in the reverse scan of the current–voltage curve as well as an additional electronic signal, detected by impedance spectroscopy measurements. The dependence of this additional signal on the optical excitation wavelength used in the IS experiments suggests that it stems from an interfacial process. Calculations using a drift-diffusion model which explicitly considers the selective contacts reproduces qualitatively the main features observed experimentally. These results demonstrate that for a solar cell in which the contact is working properly the open-circuit photovoltage is mainly determined by bulk recombination, whereas the introduction of a “bad contact” shifts the balance to surface recombination., The authors thank Junta de Andalucía for financial support via grant FQM 1851 and FQM 2310. The authors thank Ministerio de Economía y Competitividad of Spain and Agencia Estatal de Investigación (AEI) and EU (FEDER) under grants MAT2013‐47192‐C3‐3‐R, MAT2016‐76892‐C3‐2‐R, MAT2016‐79866‐R and Red de Excelencia “Emerging photovoltaic Technologies” for financial support. J.R.S.‐V. and A.B. acknowledge Marie Skłodowska‐Curie ActionsH2020‐MSCA‐IF‐2014 PlasmaPerovSol grant (Project ID 661480) and the University of Seville through the VI PPIT‐US. J.M.C. and N.E.C. were supported by EPSRC funded studentships from the CDT in New and Sustainable Photovoltaics (reference EP/L01551X/1). A.B.W. was supported by the Energy oriented Centre of Excellence (EoCoE), Horizon2020 grant research number 676629.