Pasar al contenido principal

APLICACION DE LAS ALEACIONES BASE-FE NANOESTRCTURADAS COMO SOLUCION SOSTENIBLE PARA LOS SISTEMAS DE GENERACION DE ENERGIA DE ALTA EFICIENCIA

MAT2016-80875-C3-1-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Ausforming Temperature on the Microstructure of G91 Steel

  • Vivas Méndez, Javier
  • Capdevila, Carlos
  • Jiménez, José Antonio
  • Benito-Alfonso, Miguel
  • San-Martín, David
The development of thermomechanical treatments (TMT) has a high potential for improving creep-strength in 9Cr-1Mo ferritic/martensitic steel (ASTM T/P91) to operate at temperatures beyond 600 °C. To maximize the number of nanoscale MX precipitates, an ausforming procedure has been used to increase the number of nucleation sites for precipitation inside the martensite lath. Relative to standard heat treatments (consisting of austenitization at about 1040 °C followed by tempering at about 730 °C) this processing concept has enabled achieving a microstructure containing approximately three orders of magnitude higher number density of MX precipitates having a size around four times smaller in ASTM T/P91 steel. On the other hand; this TMT has little effect on the size and number density of M<sub>23</sub>C<sub>6</sub> particles. The optimized microstructure produced by this TMT route proposed is expected to improve the creep strength of this steel., The authors acknowledge financial support to Spanish Ministerio de Economia y Competitividad (MINECO) in the form of a Coordinate Project (MAT2016-80875-C3-1-R). The work presented here is done within the Joint Program on Nuclear Materials of the European Energy Research Alliance Pilot Project CREMAR. The authors also would like to acknowledge financial support to Comunidad de Madrid through DIMMAT-CM_S2013/MIT-2775 project., We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

In-Situ Investigation of Strain-Induced Martensitic Transformation Kinetics in an Austenitic Stainless Steel by Inductive Measurements

  • Celada-Casero, Carola
  • Kooiker, Harm
  • Groen, Manso
  • Post, Jan
  • San-Martín, David
An inductive sensor developed by Philips ATC has been used to study in-situ the austenite (γ) to martensite (α′) phase transformation kinetics during tensile testing in an AISI 301 austenitic stainless steel. A correlation between the sensor output signal and the volume fraction of α′-martensite has been found by comparing the results to the ex-situ characterization by magnetization measurements, light optical microscopy, and X-ray diffraction. The sensor has allowed for the observation of the stepwise transformation behavior, a not-well-understood phenomena that takes place in large regions of the bulk material and that so far had only been observed by synchrotron X-ray diffraction., We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI)., Carola Celada-Casero acknowledges the financial support from Consejo Superior de Investigaciones Científicas (CSIC) in the form of a JAE-Predoc grant (JAEPre_2011_01167), co-funded by the European Social Fund. The authors deeply acknowledge the financial support from Research Fund for Coal for funding this research under the Contract RFCS-02-2015 (Grant Agreement No.: RFSR-CT-2012-00021) and the Spanish Ministerio de Economia y Competitividad (MINECO) through the form of a Coordinate Project (MAT2016-80875-C3-1-R). Authors are also grateful to Jose Antonio Jimenez (CENIM-CSIC), Julio Romero de Paz (CAI of Physical Techniques, UCM) and Marijke de Vries and Ronald van der Linden (Philips ATC) for the experimental support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of extensive and limited plastic deformation on recrystallized microstructure of oxide dispersion strengthened Fe-Cr-Al alloy

  • Capdevila, Carlos
  • Rementería, Rosalía
  • Aranda, M. M.
  • Vivas Méndez, Javier
  • Chao, Jesús
  • Amigó, Vicente
Ferritic oxide dispersion-strengthened alloys (ODS) are manufactured using a mechanical alloying process. The development of a coarse-grained microstructure during recrystallization has been detected and discussed by several authors, but the mechanism of grain growth remains uncertain. Recent work has emphasized the large influence of non-uniformities on the development of the recrystallized microstructure. The purpose of the present work is to study the effect of both slight heterogeneous plastic strains and strong directional deformation on recrystallization of a ferritic Fe-base ODS alloy., The authors acknowledge financial support from the Spanish Ministerio de Economia y Competitividad (MINECO) in the form of a Coordinate Project (MAT2016-80875-C3-1-R). The work presented here is done within the Joint Programme on Nuclear Materials of the European Energy Research Alliance Pilot Project CREMAR. The authors would also like to acknowledge financial support from Comunidad de Madrid through DIMMAT-CM_S2013/MIT-2775 project. J. Vivas acknowledges financial support in the form of a FPI Grant BES-2014-069863., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Understanding Mechanical Properties of Nano-Grained Bainitic Steels from Multiscale Structural Analysis

  • García Caballero, Francisca
  • Rementería, Rosalía
  • Morales-Rivas, Lucía
  • Benito-Alfonso, Miguel
  • Yang, Jer-Ren
  • Castro Mazariegos, David de
  • Poplawsky, Jonathan D.
  • Sourmail, Thomas
  • García Mateo, Carlos
Steel components working in extreme conditions require materials presenting the highest performances. Nowadays, nanoengineering is being applied to the development of ultra-high strength steels as a key-enabling technology in the steel sector. The present article describes the multiscale structure of nano-grained steels designed using atomic transformation theory and processed by a simple heat treatment. Outstanding mechanical properties for these novel steels are reported, and strain-hardening mechanisms are discussed., This research was funded by the European Research Fund for Coal and Steel under the contracts RFSR-CT-2014-00016 and RFSR-CT-2014-00019 and the Spanish Ministry of Economy and Competitiveness under the contracts MAT2016-80875-C3-1-R, We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructural Degradation and Creep Fracture Behavior of Conventionally and Thermomechanically Treated 9% Chromium Heat Resistant Steel

  • Vivas Méndez, Javier
  • Capdevila, Carlos
  • Altstadt, Eberhard
  • Houska, M.
  • Sabirov, IIchat
  • San-Martín, David
The microstructural degradation and the creep fracture behavior of conventionally and thermomechanically treated Grade 91 steel were investigated after performing small punch creep tests. A remarkable reduction in creep ductility was observed for the samples thermomechanically treated in comparison to those conventionally treated under the tested conditions of load (200 N) and temperature (700 °C). A change in the fracture mechanism from a ductile transgranular fracture to a brittle intergranular fracture was observed when changing from the conventionally treated to the thermomechanically treated processing condition, leading to this drop in creep ductility. The change in the fracture mechanism was associated to the localized concentration of creep deformation, close to coarse M23C6 carbides, at the vicinity of prior austenite grain boundaries (PAGB) in the thermomechanically treated samples. The preferential recovery experienced at the vicinity of PAGB produced the loss of the lath structure and the coarsening of the M23C6 precipitates. The electron microscopy images provided suggest that the creep cavities nucleate in these weak recovered areas, associated to the presence of coarse M23C6. After the coalescence of the cavities the propagation of the cracks was facilitated by the large prior austenite grain size produced during the austenitization which favors the propagation of the cracks along grain boundaries triggering the intergranular brittle fracture. This fracture mechanism limits the potential use of the proposed thermomechanical processing routes., Authors acknowledge financial support to Ministerio de Economia y Competitividad (MINECO) through in the form of a Coordinate Project (MAT2016-80875-C3-1-R). Authors also would like to acknowledge financial support to Comunidad de Madrid through DIMMAT-CM_S2013/MIT-2775 project. The authors are grateful for the dilatometer tests by Phase Transformation laboratory. J.Vivas acknowledges financial support in the form of a FPI Grant BES-2014-069863. This work contributes to the Joint Programme on Nuclear Materials (JPNM) of the European Energy Research Alliance (EERA)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación

Advanced heat treatments and complex ferritic structures for bearing steels

  • García Caballero, Francisca
  • Pujante, Jaume
  • Sourmail, Thomas
  • Rementería, Rosalía
  • Castro Mazariegos, David de
  • Dierickx, Pierre
  • Ramírez, Giselle
  • Sidoroff-Coicaud, Christine
  • Valizadeh Moghaddam, Pouria
  • Vuorinen, Esa
Nanostructured bainitic steels exhibit an optimum strength/toughness combination as a consequence of their extremely fine structure. They have also demonstrated potential for wear-resistance applications. The aim of this work was to develop bearing steels by the multi-scale control of complex ferritic structures, designed using atomic transformation theory and processed by novel heat treatments. Based on the results, the new ball bearings outperformed conventional grades, approaching more expensive material options., This research was funded by the European Research Fund for Coal and Steel under the contract RFSR-CT-2014-00016. D.D.C. acknowledges the Spanish Ministry of Science Economy and Competitiveness for his PhD research grant, reference BES-2017-080945.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The influence of texture on the ductile-to-brittle transition behavior in Fe20Cr4.5Al oxide dispersion strengthened alloy

  • Chao, Jesús
  • Capdevila, Carlos
This paper reports on hardness, tensile properties and notch impact bending toughness values of an Fe20Cr4.5Al oxide dispersion strengthened (ODS) alloy specifically processed to achieved different preferential orientations: random, <100>, <110> and <111> parallel to the bar axis. In spite of the differences in the grain size, it was found for <100>, <111> and random orientations that the mean hardness values on the transverse cross sections is not remarkably sensitive to the texture. On the other hand, a significantly different mean hardness value for the material having the <110> crystalline orientation was found. Regarding the yield strength, it was found for random, <100> and <111> orientations that the yield strength is proportional to the Taylor’s factor. The difference between experimental and predicted yield strength values for <110> orientation was attributed to the offset effect induced by the dislocation cell size. The variation of the cleavage fracture strength with the texture was analyzed in the basis of two criteria: one based on the Normal Stress Law (macroscopic nature), and the other based on the assumption that fracture occurs from the propagation of a microcrack-like defect (microscopic nature). In this sense, it was concluded from the fractographic evidences that random and <100> orientations follow a mechanism where the fracture kinks along of the cleavage plane from a penny shaped microcrack nucleated in a second phase particle, meanwhile in the <110> and <111> orientations the fracture propagation arises from a penny shaped defect on the cleavage plane. Finally, the lower shelf values determined for the conditions studied are the same regardless of the texture and microstructure. The effect of texture on the notch toughness was noted where plastic flow predominates, i.e., in the ductile to brittle transition temperature and in the upper shelf energy., This research received funding from the Spanish Ministerio de Ciencia, Innovación y Universidades in the form of a Coordinate Project (MAT2016-80875-C3-1-R). The authors would like to acknowledge financial support from the Comunidad de Madrid through DIMMAT-CM_S2013/MIT-2775 project.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Effect of Ausforming on Creep Strength of G91 Heat-Resistant Steel

  • Vivas Méndez, Javier
  • Rementería, Rosalía
  • Serrano, M.
  • Altstadt, Eberhard
  • San-Martín, David
  • Capdevila, Carlos
Título Libro: Processing and Manufacturing of Advanced Materials, The major challenge in a heat-resistant steel is to generate thermally stable microstructures that allow increasing the operating temperature, which will improve the thermal efficiency of the power plant without diminishing strength or time to rupture. The strengthening mechanism in tempered martensitic 9Cr steels comes mainly from the combination of solid solution effect and of precipitation hardening by fine MX carbo-nitrides, which enhance the sub-boundary hardening. This work is focused on the effect of ausforming processing on MX nanoprecipitation, on both their distribution and number density, during the subsequent tempering heat treatment. The creep strength at 700 oC was evaluated by small punch creep tests. The creep results after ausforming were compared to those obtained after conventional heat treatment concluding, in general, that ausforming boosts the creep strength of the steel at 700 oC. Therefore, conventional ausforming thermomechanical treatment is a promising processing route to raise the operating temperature of 9Cr heat-resistant steels., Authors acknowledge financial support to Spanish Ministerio de Economia y Competitividad (MAT2016-80875-C3-1-R) and Comunidad de Madrid (DIMMAT-CM_S2013/MIT-2775). This work is carried out under the auspices of the Joint Programme on Nuclear Materials of the European Energy Research Alliance Pilot Project CREMAR. J. Vivas acknowledges financial support in the form of a FPI Grant BES-2014-069863.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Design and high temperature behavior of novel heat resistant steels strengthened by high density of stable nanoprecipitates

  • Vivas Méndez, Javier
  • Castro Mazariegos, David de
  • Altstadt, Eberhard
  • Houska, M.
  • San-Martín, David
  • Capdevila, Carlos
International efforts have been focused on the development of new 9Cr Ferritic/Martensitic steels capable of operating at temperatures above 700 °C to improve thermal efficiency of new power plants. The distribution and size of the MX nanoprecipitates present in these steels have been reported to be the key factor for improving the thermal stability of the microstructure during creep. Bearing in mind these findings, three different heat resistant steels were designed to have a higher number density of MX nanoprecipitates than commercial 9Cr Ferritic/Martensitic steels. The manufacturing and subsequent microstructural characterization carried out showed that this goal was achieved. Preliminary high temperature strength results performed by means of Small Punch Creep Tests (SPCT) demonstrated that these new steels improve significantly the high temperature strength without an important loss of ductility as compared to a current commercial 9Cr Ferritic/Martensitic steel., Authors acknowledge financial support to Spanish Ministerio de Economia y Competitividad (MINECO) in the form of a Coordinate Project (MAT2016-80875-C3-1-R). Authors also would like to acknowledge financial support to Comunidad de Madrid through DIMMAT-CM_S2013/MIT-2775 project. J. Vivas acknowledges financial support in the form of a FPI Grant BES-2014-069863. This work contributes to the Joint Programme on Nuclear Materials (JPNM) of the European Energy Research Alliance (EERA).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of the microsegregation on martensitic and bainitic reactions in a high carbon-high silicon cast steel

  • Basso, A. D.
  • Toda Caraballo, Isaac
  • Eres-Castellanos, Adriana
  • San-Martín, David
  • Jiménez, José Antonio
  • García Caballero, Francisca
Casting processes show some weaknesses. A particular problem is presented when the workpiece needs to be subjected to heat treatments to achieve a desired microstructure. This problem arises from the microsegregation phenomena typically present in cast parts. The effect of the microsegregation on the martensitic and bainitic transformations has been investigated in a high carbon-high silicon cast steel, with the approximate composition Fe-0.8C-2Si-1Mn-1Cr (in wt. %), which was poured into 25 mm keel block-shaped sand molds. The microsegregation maps of Cr, Si, and Mn characterized by electron probe microanalysis (EPMA) show that interdendritic regions are enriched while dendrites are impoverished in these elements, implying that their partition coefficients are lower that the unity (k < 1). As-quenched martensitic and austempered bainitic microstructures (at 230 ⁰C) were obtained and analyzed after applying an austenitization heat treatment at 920 ⁰C (holding for 60 min). The thermal etching method used to reveal the prior austenite grain size showed a bimodal grain size distribution, with larger grains in the dendritic regions (≈22.4µm) than in the interdendritic ones (≈6.4 µm). This is likely due to both the microsegregation and the presence of small undissolved cementite precipitates. Electron Backscatter Diffraction (EBSD) analysis carried out on the martensitic microstructure do not unveil any differences in misorientation distribution frequency and block size between the dendritic and interdendritic zones related to the microsegregation and bimodality of the austenite grain size. On the contrary, the bainitic transformation starts earlier (incubation time of 80 min), proceeds faster and bainitic ferrite plates are longer in the dendritic zones, were prior austenite grains are larger and impoverish in solute. The presence of these microsegregation pattern leads to the non-uniform development of the bainitic reaction in cast parts, modifying its kinetics and the resulting microstructures, which would probably have a major impact on the mechanical properties., This work has been supported by CONICET, ANPCyT and MINCyT of Argentina [Project PICT 12-1146]. Some of the authors (ITC, DSM, FGC) also acknowledge financial support from the Ministerio de Economia y Competitividad (MINECO) in the form of a Coordinate Project (MAT2016-80875-C3-1-R) and to the Comunidad de Madrid through P2018/NMT4381project. ITC is also grateful for financial support in the form of a fellowship 2016-T2/IND-1693, from the Programme Atracción de Talento Investigador (Conserjería de Educación, Juventud y Deporte, Comunidad de Madrid).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Positron Annihilation Spectroscopy Study of Carbon-Vacancy Interaction in Low-Temperature Bainite

  • Rementería, Rosalía
  • Domínguez-Reyes, Ricardo
  • Capdevila, Carlos
  • García Mateo, Carlos
  • García Caballero, Francisca
Nano-scale investigations of bainitic structures formed at temperatures below 350 °C have shown that the bainitic ferrite lattice is super-saturated in carbon. A high density of intrinsic defects would be playing a part in the carbon-supersaturation levels detected. In this work, the role of C−vacancy complexes on carbon-supersaturation in low temperature bainite is investigated by means of Positron Annihilation Spectroscopy. Results reveal the presence of a significant amount of monovacancies in the structures that plays an important role on the formation of carbon clusters in the ferrite lattice of nano-scale bainitic structures., Tis research was supported by the Spanish Ministerio de Economia y Competitividad (MINECO) in the form of a Coordinate Project (MAT2016-80875-C3-1-R and ENE2015-70300-C3-2-R); by the Regional Government of Madrid through the programs S2013/MAE-2745 TECHNOFUSION(II)-CM MINECO/FEDER, and S2013/MIT-2862-MULTIMAT-CHALLENGE; and the Research Fund for Coal and Steel under the Contracts RFCS-CT-2015-709607 and RFCS-CT-2016-754070.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of cast part size on macro- and microsegregation patterns in a high carbon high silicon steel

  • Basso, A.
  • Toda Caraballo, Isaac
  • San-Martín, David
  • García Caballero, Francisca
In this work, the macro and microsegregation of Cr, Si and Mn have been investigated in a high-carbon high-silicon cast steel using X-ray fluorescence (XRF) and electron probe microanalysis (EPMA), respectively. Two different keel block sizes with leg thicknesses of 12.5 and 75 mm have been compared. In each of the keel blocks, three different locations along the leg thickness have been analyzed: A) zone near surface (≈1 mm); C) the central zone of the leg thickness and B) an equidistant zone from A and C. After comparing the analysis performed by XRF in these three zones no macrosegregation of the Cr, Mn and Si has been observed in any of the two keel blocks. However, clear microsegregation patterns have been obtained by EPMA for these three elements; interdendritic zones are enriched while dendrites are impoverished in these elements implying that their partition coefficient is lower that the unity (k < 1). This coefficient has been estimated using the EPMA measurements and Thermo-Calc calculations, finding good agreement between both approaches for Si and Mn but not for Cr. Finally, for both keel block leg thicknesses, similar microsegregation intensity, measured in terms of alloying element concentration has been observed. This result suggests that the cast part size (or dimension) do not have a strong influence on the microsegregation profiles. This it attributed to the back diffusion phenomena involving redistribution of solute during the solidification process., This work has been supported by CONICET, ANPCyT and MINCyT of Argentine [Project PICT 12-1146]. Some of the authors (ITC, DSM, FGC) also acknowledge financial support from the Ministerio de Economia y Competitividad (MINECO) in the form of a Coordinate Project (MAT2016-80875-C3-1-R) and to the Comunidad de Madrid through DIMMAT-CM_S2013/MIT-2775 project. Authors are also grateful to Dr. José Antonio Jiménez for the experimental support with the X-ray fluorescence analysis, the Phase Transformations and Microscopy labs from CENIM-CSIC, and the ICTS Centro Nacional de Microscopía Electrónica (CNME) located at the Complutense University of Madrid, for the provision of laboratory facilities (EMPA) and technical support. ITC is also grateful for financial support of the fellowship 2016-T2/IND-1693, from the Programme Atracción de talento investigador (Consejería de Educación, Juventud y Deporte, Comunidad de Madrid).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Electrical Steels

  • Capdevila, Carlos
Chapter 12 Electrical Steels, A developed electrical system enables power to be generated at key locations and distributed widely. To realize such a system requires means of generation, distribution and utilization. Electrical steels play a key role in an electrical system, alongside copper conductors, they make the whole system feasible. This chapter reviews the production and recent developments, with special attention to coating technologies, of the two main groups of electrical steels, i.e. the grain-oriented electrical steels and the non-grain-oriented grain electrical steels., The author acknowledges financial support to Spanish Ministerio de Economia y Competitividad (MINECO) through in the form of a Coordinate Project (MAT2016-80875-C3-1-R). Authors also acknowledge financial support to Comunidad de Madrid through DIMMAT-CM_S2013/MIT-2775 project.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Nanostructured Steels

  • Capdevila, Carlos
  • García Caballero, Francisca
  • Rementería, Rosalía
Chapter 8 Nanostructured Steels, Nanostructured metals with grain sizes smaller than 100 nm usually exhibit strengths which can be more than twice higher than their coarse-grained counterparts. The “smaller is stronger” effect is generally understood in terms of the Hall-Petch effect of grain size strengthening, or the capability of grain boundaries to obstruct the motion of dislocations as carriers of plastic deformation. Nanostructured steels take benefit of reductions in the grain size to show improved tensile strength, hardness and in-service properties. The steel nanostructures are usually multi-phase and hierarchical, maintaining or even improving the stress-ductility trade-off. The increasing demands for stronger, tougher, wear resistant and heat-tolerant materials have led to the development of new families of steels where the length scale that controls such properties is in the nanometer range. This chapter provides an overview of the current status of the most technologically relevant bulk nanostructured steels, describing the approaches to metallurgical design, processing routes, mechanical properties, in-use behavior and industrial applications., The authors acknowledge financial support from the Spanish Ministerio de Economia y Competitividad (MINECO) in the form of a coordinate project (MAT2016-80875-C3-1-R) and the Research Fund for Coal and Steel of the European Commission under the contract SuperHigh (RFSR-CT-2014-00019).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Creep strength boosted by a high-density of stable nanoprecipitates in high-chromium steels

  • Vivas Méndez, Javier
  • Castro Mazariegos, David de
  • Poplawsky, Jonathan D.
  • Altstadt, Eberhard
  • Houska, M.
  • Urones-Garrote, E.
  • San-Martín, David
  • García Caballero, Francisca
  • Serrano, M.
  • Capdevila, Carlos
There is a need worldwide to develop materials for advanced power plants with steam temperatures of 700 °C and above that will achieve long-term creep-rupture strength and low CO2 emissions. The creep resistance of actual 9-12Cr steels is not enough to fulfil the engineering requirements above 600 °C. In this paper, the authors report their advances in the improvement of creep properties of this type of steels by the microstructural optimization through nano-precipitation using two methodologies. 1) Applying a high temperature austenitization cycle followed by an ausforming step (thermomechanical treatment, TMT) to G91 steel, to increase the martensite dislocation density and, thus, the number density of MX precipitates (M = V,Nb; X = C,N) but at the expense of deteriorating the ductility. 2) Compositional adjustments, guided by computational thermodynamics, combined with a conventional heat treatment (no TMT), to design novel steels with a good ductility while still possessing a high number density of MX precipitates, similar to the one obtained after the TMT in G91. The microstructures have been characterized by optical, scanning and transmission electron microscopy, EBSD and atom probe tomography. The creep behaviour at 700 °C has been evaluated under a load of 200 N using small punch creep tests., Authors acknowledge financial support to Agencia Estatal de Investigación (AEI) in the form of Coordinate Projects MAT2016-80875-C3-1-R and PID2019-109334RB-C31. J. Vivas acknowledges financial support in the form of a FPI Grant BES-2014-069863. D. De-Castro acknowledges financial support in the form of a FPI Grant BES-C-2017-0090. APT was conducted at ORNL's Center for Nanophase Materials Sciences (CNMS), which is a U.S. DOE Office of Science User Facility.