Pasar al contenido principal

EVALUACION DE LA DURABILIDAD Y LA POLARIDAD SUPERFICIAL DE MATERIALES POROSOS ACTUADOS ELECTRICAMENTE PARA FINES ENERGETICOS Y TECNOLOGIAS SOSTENIBLES DE INGENIERIA DE TEJIDOS

MAT2017-86357-C3-2-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario FUNDACION CIDETEC

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Functional macroporous iron-phosphorous films by electrodeposition on colloidal crystal templates

  • Golvano Escobal, Irati|||0000-0001-8518-8185
  • de Paz Castany, Roger|||0000-0003-4211-2636
  • Alcantara, Carlos
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • García-Lecina, Eva|||0000-0001-8915-840X
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Pseudo-ordered macroporous iron-phosphorous (Fe-P) films have been electrodeposited potentiostatically from a citrate-sulfate bath onto Au surfaces pre-patterned with a colloidal crystal mask of polystyrene spheres of 350 nm in diameter. The electrolyte contained sodium hypophosphite as the P source, enabling the incorporation of 6-14 at.% P. For comparative purposes, continuous films have been obtained galvanostatically on unpatterned Au surfaces. In both cases, the P content could be varied to a certain extent by adjusting the deposition potential or current density. Tunable microstructure and magnetic response was observed due to the dissimilar chemical composition, with coercivity values being larger in the macroporous films. Additionally, wettability analyses showed that these were more hydrophobic, reaching contact angle values of about 130∘. In spite of their hydrophobic character, the samples were catalytic toward oxygen evolution reaction (OER) in alkaline media. The macroporous Fe-P films showed faster kinetics for OER than their nonporous counterparts. Our results show that electrodeposited porous Fe-P based materials show an interesting combination of properties which make them appealing for applications including water cleaning, soft-magnetic components, or electrocatalytic production of oxygen, to name a few.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Monolayered versus multilayered electroless NiP coatings, Impact of the plating approach on the microstructure, mechanical and corrosion properties of the coatings

  • Salicio-Paz, Asier|||0000-0002-0500-6634
  • Grande, H.
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Offoiach, R.
  • Lekka, M.
  • García-Lecina, Eva|||0000-0001-8915-840X
Electroless nickel-phosphorous (NiP) coatings were produced on low carbon steel substrates for a total plating time of 3 h. Different preparation modalities were pursued. Multilayered coatings were produced by stacking three layers of the same composition by successive electroless plating with rinsing steps in between. On the other hand, coatings termed 'monolayered' for the sake of comparison were deposited by one step electroless process, with and without undergoing bath replenishment of the electrolyte during plating. All the samples were subjected to thermal annealing at 400 °C for 1 h under argon atmosphere. The results show that the multilayer approach prevents crack propagation in the as-deposited coatings because the interfaces between layers block the advance of defects. Bath replenishment during monolayered coatings production creates pseudo-interfaces similar to those of the multilayered case but they are ineffective in terms of corrosion protection. Un-replenishment of the electrolyte promotes a change in the coating's microstructure from lamellar to columnar which severely worsens their performance. Upon annealing, the presence of interfaces, along with the recrystallization of the metallic matrix, promotes an upgrading of the corrosion performance of the multi-layered coatings. The corrosion products spread laterally at the interface where they stockpile. At a certain point, the accumulation of these by-products provokes the exfoliation of the outermost layer exposing the layer underneath to the corrosive media, thereby delaying the advancement of the corrosion attack. The results of this study highlight the importance of the plating approach selection, as well as the need for proper electrolyte maintenance during the production of high-performance electroless coatings.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanocrystalline electrodeposited Fe-W/Al2O3 Composites, effect of Alumina Sub-microparticles on the mechanical, tribological, and corrosion properties

  • Nicolenco, Aliona|||0000-0003-4624-2163
  • Mulone, Antonio
  • Imaz, Naroa
  • Tsyntsaru, Natalia|||0000-0002-9813-2460
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
  • Klement, Uta
  • Cesiulis, Henrikas|||0000-0002-5077-7884
  • García-Lecina, Eva|||0000-0001-8915-840X
In this study, nanocrystalline Fe-W alloy and Fe-W/Al2O3 composite coatings with various contents of sub-microsized alumina particles have been obtained by electrodeposition from an environmentally friendly Fe(III)-based electrolyte with the aim to produce a novel corrosion and wear resistant material. The increase in volume fraction of Al2O3 in deposits from 2 to 12% leads to the grain refinement effect, so that the structure of the coatings change from nanocrystalline to amorphous-like with grain sizes below 20 nm. Nevertheless, the addition of particles to the Fe-W matrix does not prevent the development of a columnar structure revealed for all the types of studied coatings. The observed reduction in both hardness and elastic modulus of the Fe-W/Al2O3 composites is attributed to the apparent grain size refinement/amorphization and the nanoporosity surrounding the embedded Al2O3 particles. In the presence of 12 vol% of Al2O3 in deposits, the wear rate decreases by a factor of 10 as compared to Fe-W alloy tested under dry friction conditions due to the lowering of tribo-oxidation. The addition of alumina particles slightly increases the corrosion resistance of the coatings; however, the corrosion in neutral chloride solution occurs through the preferential dissolution of Fe from the matrix. The obtained results provide a possibility to integrate the nanocrystalline Fe-W/Al2O3 composite coatings into various systems working under dry friction conditions, for example, in high-temperature vacuum systems.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electroless Palladium-Coated Polymer Scaffolds for Electrical Stimulation of Osteoblast-Like Saos-2 Cells

  • Careta, Oriol|||0000-0003-1333-0300
  • Salicio-Paz, Asier|||0000-0002-0500-6634
  • Pellicer, Eva|||0000-0002-8901-0998
  • Ibáñez, Elena|||0000-0002-0275-6958
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • García-Lecina, Eva|||0000-0001-8915-840X
  • Sort, Jordi|||0000-0003-1213-3639
  • Nogués, Carme|||0000-0002-6361-8559
Three-dimensional porous scaffolds offer some advantages over conventional treatments for bone tissue engineering. Amongst all non-bioresorbable scaffolds, biocompatible metallic scaffolds are preferred over ceramic and polymeric scaffolds, as they can be used as electrodes with different electric field intensities (or voltages) for electric stimulation (ES). In the present work we have used a palladium-coated polymeric scaffold, generated by electroless deposition, as a bipolar electrode to electrically stimulate human osteoblast-like Saos-2 cells. Cells grown on palladium-coated polyurethane foams under ES presented higher proliferation than cells grown on foams without ES for up to 14 days. In addition, cells grown in both conditions were well adhered, with a flat appearance and a typical actin cytoskeleton distribution. However, after 28 days in culture, cells without ES were filling the entire structure, while cells under ES appeared rounded and not well adhered, a sign of cell death onset. Regarding osteoblast differentiation, ES seems to enhance the expression of early expressed genes. The results suggest that palladium-coated polyurethane foams may be good candidates for osteoblast scaffolds and demonstrate that ES enhances osteoblast proliferation up to 14 days and upregulate expression genes related to extracellular matrix formation.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Full optimization of an electroless nickel solution, boosting the performance of low-phosphorous coatings

  • Salicio-Paz, Asier|||0000-0002-0500-6634
  • Ugarte, Ixone
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
  • García-Lecina, Eva|||0000-0001-8915-840X
Univariate and multivariate optimizations of a novel electroless nickel formulation have been carried out by means of the Taguchi method. From the compositional point of view, adjustment of the complexing agent concentration in solution is crucial for fine-tuning free Ni2+ ions concentration and, in turn, the mechanical properties of the resulting coatings. The Ni (II) concentration and the pH are the main parameters which help restrict the incorporation of phosphorous into the Ni layers. On the other hand, the stirring rate, the pH and the reducing agent concentration are the most influential parameters for the corrosion resistance of the coatings. Multivariate optimization of the electrolyte leads to a set of optimized parameters in which the mechanical properties (hardness and worn volume) of the layers are similar to the optimal values achieved in the univariate optimization, but the corrosion rate is decreased by one order of magnitude.