Pasar al contenido principal

-

RYC-2012-10839

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Contratación e Incorporación de RRHH
Subprograma Subprograma Ramón y Cajal (RYC)
Convocatoria Ramón y Cajal
Año convocatoria 2012
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSIDAD AUTONOMA DE BARCELONA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 59
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanomechanical behavior of 3D porous metal-ceramic nanocomposite Bi/Bi2 O3 films

  • Domingo Roca, Roger|||0000-0002-0557-5431
  • Esqué-de los Ojos, Daniel|||0000-0002-6279-2037
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Pellicer, Eva|||0000-0002-8901-0998
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Sort, Jordi|||0000-0003-1213-3639
The nanomechanical properties of three-dimensional (3D) porous metal/metal oxide composite (Bi/Bi2O3) films grown by direct current electrodeposition have been studied by nanoindentation at two different loading rates. The synthesized films exhibit a mixture of crystallographic phases of metallic Bi and α-Bi2O3, as evidenced by X-ray diffraction. An in-situ compaction of the sample during the nanoindentation assays has been observed. This in-situ compaction has an influence over both the hardness and elastic modulus of the material, being more important on the latter and, therefore, on the determination of the degree of porosity of the composite film. The influence of the loading rate on the mechanical properties has been investigated. In addition, time-dependent deformation processes (creep tests) have been also performed, revealing an anelastic behavior irrespective of the loading rate. From these creep tests, a viscoelastic non-Newtonian behavior of the sample is evidenced, which is well-described by a three-element Voigt model.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Structurally and mechanically tunable molybdenum oxide films and patterned submicrometer structures by electrodeposition

  • Quintana, Alberto|||0000-0002-9813-735X
  • Varea Espelt, Aïda
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Baró, M. D.|||0000-0002-8636-1063
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
1.5 μm-thick molybdenum oxide films have been electrodeposited potentiostatically from 0.2 M Na₂MoO₄ electrolyte onto indium tin oxide (ITO)/glass substrates at pH = 1, 6 and 9. The influence of cetyltrimethylammonium bromide (CTAB) surfactant on films' adhesion, morphology, degree of porosity, molybdenum speciation, and crystallographic structure has been systematically investigated. The addition of CTAB (0.01 M) to the bath clearly improves film adherence to the substrate, reduces cracking, and increases crystallinity. This has an impact on the physical properties of the films. In particular, both hardness (H) and Young's modulus (E) increase, as determined from nanoindentation tests. The growth of ordered arrays of molybdenum oxide submicrometer structures, including pillars and stripes, by electrodeposition onto e-beam lithographed Au/Ti/Si substrates is also reported.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanostructured Ti-Zr-Pd-Si-(Nb) bulk metallic composites, novel biocompatible materials with superior mechanical strength and elastic recovery

  • Hynowska, Anna
  • Blanquer, Andreu|||0000-0002-3551-1885
  • Pellicer, Eva|||0000-0002-8901-0998
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Baró, M. D.|||0000-0002-8636-1063
  • Gebert, A.
  • Calin, Mariana
  • Eckert, Jürgen|||0000-0003-4112-3181
  • Nogués, Carme|||0000-0002-6361-8559
  • Ibáñez, Elena|||0000-0002-0275-6958
  • Barrios, Leonardo|||0000-0002-6151-8503
  • Sort, Jordi|||0000-0003-1213-3639
The microstructure, mechanical behaviour, and biocompatibility (cell culture, morphology, and cell adhesion) of nanostructured Ti45 Zr15 Pd35- x Si5 Nbx with x = 0, 5 (at. %) alloys, synthesized by arc melting and subsequent Cu mould suction casting, in the form of rods with 3 mm in diameter, are investigated. Both Ti-Zr-Pd-Si-(Nb) materials show a multi-phase (composite-like) microstructure. The main phase is cubic β-Ti phase (Im3m) but hexagonal α-Ti (P63/mmc), cubic TiPd (Pm3m), cubic PdZr (Fm3m), and hexagonal (Ti, Zr)5 Si3 (P63/mmc) phases are also present. Nanoindentation experiments show that the Ti45 Zr15 Pd30 Si5 Nb5 sample exhibits lower Young's modulus than Ti45 Zr15 Pd35 Si5 . Conversely, Ti45 Zr15 Pd35 Si5 is mechanically harder. Actually, both alloys exhibit larger values of hardness when compared with commercial Ti-40Nb, (HTi-Zr-Pd-Si ≈ 14 GPa, HTi-Zr-Pd-Si-Nb ≈ 10 GPa and HTi-40Nb ≈ 2.7 GPa). Concerning the biological behaviour, preliminary results of cell viability performed on several Ti-Zr-Pd-Si-(Nb) discs indicate that the number of live cells is superior to 94% in both cases. The studied Ti-Zr-Pd-Si-(Nb) bulk metallic system is thus interesting for biomedical applications because of the outstanding mechanical properties (relatively low Young's modulus combined with large hardness), together with the excellent biocompatibility.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Protective coatings for intraocular wirelessly controlled microrobots for implantation, corrosion, cell culture, and in vivo animal tests

  • Pokki, Juho
  • Ergeneman, Olgaç
  • Chatzipirpiridis, George
  • Lühmann, Tessa
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
  • Pot, Simon A.
  • Spiess, Bernhard M.
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Nelson, Bradley J.|||0000-0001-9070-6987
Diseases in the ocular posterior segment are a leading cause of blindness. The surgical skills required to treat them are at the limits of human manipulation ability, and involve the risk of permanent retinal damage. Instrument tethering and design limit accessibility within the eye. Wireless microrobots suturelessly injected into the posterior segment, steered using magnetic manipulation, are proposed for procedures involving implantation. Biocompatibility is a prerequisite for these procedures. This paper investigates the use of cobalt-nickel microrobots coated with polypyrrole, and gold, which has been used as an ocular implant material. Polypyrrole has well-established biocompatibility properties, but no reports concerning its ocular implantation is available. Coated and uncoated microrobots were investigated for their corrosion properties, and solutions that had contained coated and uncoated microrobots for one week were tested for cytotoxicity by monitoring NIH3T3 cell viability. None of the microrobots showed significant corrosion currents and corrosion potentials were as expected in relation to the intrinsic nobility of the materials. NIH3T3 cell viability was not affected by the release medium, in which coated/uncoated microrobots were stored. In vivo tests inside rabbit eyes were performed using coated microrobots. There were no significant inflammatory responses during the first week after injection. An inflammatory response detected after two weeks was likely due to a lack of longer-duration biocompatibility. The results provide valuable information for those who work on implant technology and biocompatibility. Coated microrobots have the potential to facilitate a new generation of surgical treatments, diagnostics and drug-delivery techniques, when implantation in the ocular posterior segment will be possible.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrochemically synthesized amorphous and crystalline nanowires: dissimilar nanomechanical behavior in comparison with homologous flat films

  • Zeeshan, M. Arif
  • Esqué-de los Ojos, Daniel|||0000-0002-6279-2037
  • Castro-Hartmann, Pablo|||0000-0002-8991-9560
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Nogués, Josep|||0000-0003-4616-1371
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Baró, M. D.|||0000-0002-8636-1063
  • Nelson, Bradley J.|||0000-0001-9070-6987
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
The effects of constrained sample dimensions on the mechanical behavior of crystalline materials have been extensively investigated. However, there is no clear understanding of these effects in nano-sized amorphous samples. Herein, nanoindentation together with finite element simulations are used to compare the properties of crystalline and glassy CoNi(Re)P electrodeposited nanowires (ϕ ≈ 100 nm) with films (3 μm thick) of analogous composition and structure. The results reveal that amorphous nanowires exhibit a larger hardness, lower Young's modulus and higher plasticity index than glassy films. Conversely, the very large hardness and higher Young's modulus of crystalline nanowires are accompanied by a decrease in plasticity with respect to the homologous crystalline films. Remarkably, proper interpretation of the mechanical properties of the nanowires requires taking the curved geometry of the indented surface and sink-in effects into account. These findings are of high relevance for optimizing the performance of new, mechanically-robust, nanoscale materials for increasingly complex miniaturized devices.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Toward uniform electrodeposition of magnetic Co-W mesowires arrays, direct versus pulse current deposition

  • Tsyntsaru, N.
  • Silkin, S.
  • Cesiulis, Henrikas|||0000-0002-5077-7884
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Template-assisted electrodeposition of Co-rich Co-W alloys into mesoporous anodized aluminum oxide from ammonia-free solutions is investigated. The optimum deposition conditions rendering uniform filling of the pores, either by direct current (DC) or pulse current (PC) methods, are established. Contrary to the DC deposition on flat surfaces (which is kinetically controlled), the DC electrodeposition in the mesopores of the template is limited by mass transfer. Conversely, under PC mode, the Co-W electrodeposition process is controlled by kinetics at frequencies.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Modeling the collective magnetic behavior of highly-packed arrays of multi-segmented nanowires

  • Agramunt Puig, Sebastià|||0000-0002-3627-2820
  • Valle, Nuria del|||0000-0003-2608-5009
  • Pellicer, Eva|||0000-0002-8901-0998
  • Zhang, Jin
  • Nogués, Josep|||0000-0003-4616-1371
  • Navau, Carles|||0000-0003-4763-5305
  • Sánchez Moreno, Álvaro|||0000-0002-2988-0289
  • Sort, Jordi|||0000-0003-1213-3639
A powerful model to evaluate the collective magnetic response of large arrays of segmented nanowires comprising two magnetic segments of dissimilar coercivity separated by a non-magnetic spacer is introduced. The model captures the essential aspects of the underlying physics in these systems while being at the same time computationally tractable for relatively large arrays. The minimum lateral and vertical distances rendering densely packed weakly-interacting nanowires and segments are calculated for optimizing their performance in applications like magnetic sensors or recording media. The obtained results are appealing for the design of multifunctional miniaturized devices actuated by external magnetic fields, whose successful implementation relies on achieving a delicate balance between two opposing technological demands: the need for an ultra-high density of nanowires per unit area and the minimization of inter-wire and inter-segment dipolar interactions.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Tailoring staircase-like hysteresis loops in electrodeposited trisegmented magnetic nanowires, a strategy toward minimization of interwire interactions

  • Zhang, Jin
  • Agramunt Puig, Sebastià|||0000-0002-3627-2820
  • Valle, Nuria del|||0000-0003-2608-5009
  • Navau, Carles|||0000-0003-4763-5305
  • Baró, M. D.|||0000-0002-8636-1063
  • Estrade, Sonia|||0000-0002-3340-877X
  • Peiro, Francesca|||0000-0002-5697-0554
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Nelson, Bradley J.|||0000-0001-9070-6987
  • Sánchez Moreno, Álvaro|||0000-0002-2988-0289
  • Nogués, Josep|||0000-0003-4616-1371
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
A new strategy to minimize magnetic interactions between nanowires (NWs) dispersed in a fluid is proposed. Such a strategy consists of preparing trisegmented NWs containing two antiparallel ferromagnetic segments with dissimilar coercivity separated by a nonmagnetic spacer. The trisegmented NWs exhibit a staircase-like hysteresis loop with tunable shape that depends on the relative length of the soft- and hard-magnetic segments and the respective values of saturation magnetization. Such NWs are prepared by electrodepositing CoPt/Cu/Ni in a polycarbonate (PC) membrane. The antiparallel alignment is set by applying suitable magnetic fields while the NWs are still embedded in the PC membrane. Analytic calculations are used to demonstrate that the interaction magnetic energy from fully compensated trisegmented NWs with antiparallel alignment is reduced compared to a single-component NW with the same length or the trisegmented NWs with the two ferromagnetic counterparts parallel to each other. The proposed approach is appealing for the use of magnetic NWs in certain biological or catalytic applications where the aggregation of NWs is detrimental for optimized performance.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Ni-, Pt- and (Ni/Pt)-doped TiO₂ nanophotocatalysts, a smart approach for sustainable degradation of Rhodamine B dye

  • Pol, Roberto|||0000-0002-4387-4061
  • Guerrero, Miguel|||0000-0001-8350-8261
  • García-Lecina, Eva|||0000-0001-8915-840X
  • Altube, Ainhoa
  • Rossinyol Casals, Emma|||0000-0002-1656-1254
  • Garroni, Sebastiano|||0000-0001-7686-6589
  • Baró, M. D.|||0000-0002-8636-1063
  • Pons Picart, Josefina|||0000-0003-1834-9326
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Ni (1 wt%)-, Pt (1 wt%)- and [Ni (0.5 wt%)/Pt (0.5 wt%)]-doped TiO₂ nanoporous catalysts have been successfully obtained through a facile two-step hydrothermal route. TiO₂ crystallizes mostly in the anatase phase and acts as a mesoporous matrix. Meanwhile, Ni, Pt and Ni/Pt dopants form small nanoparticles (NPs) (3-95 nm in diameter) which are hosted by the TiO₂ framework. The resulting composites exhibit a rather large surface area, in the range of 186-200 m2/g. The band gap energy reduces from 3.03 eV for the undoped TiO₂ to 2.15 eV for the Pt-loaded TiO₂. As a consequence, absorption expands toward the visible light range. The photodegradation of Rhodamine B dye in aqueous medium has been investigated under UV-vis light irradiation. The presence of Ni, Pt and Ni/Pt NPs significantly enhances the photocatalytic activity of the material. Furthermore, the Ni-doped TiO₂ shows ferromagnetic behavior at room temperature, which makes its recovery and subsequent fast reutilization possible. Interestingly, this sample also exhibits the best stability upon recycling. Considering all the current challenges in sustainable water remediation, these new photocatalysts could find applications in real environmental contexts in the near future.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

The influence of pore size on the indentation behavior of metallic nanoporous materials, a molecular dynamics study

  • Esqué-de los Ojos, Daniel|||0000-0002-6279-2037
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
In general, the influence of pore size is not considered when determining the Young's modulus of nanoporous materials. Here, we demonstrate that the pore size needs to be taken into account to properly assess the mechanical properties of these materials. Molecular Dynamics simulations of spherical indentation experiments on single crystalline nanoporous Cu have been undertaken in systems with: (i) a constant degree of porosity and variable pore diameter; and (ii) a constant pore diameter and variable porosity degree. The classical Gibson and Ashby expression relating Young's modulus with the relative density of the nanoporous metal is modified to include the influence of the pore size. The simulations reveal that, for a fixed porosity degree, the mechanical behavior of materials with smaller pores differs more significantly from the behavior of the bulk, fully dense counterpart. This effect is ascribed to the increase of the overall surface area as the pore size is reduced, together with the reduced coordination number of the atoms located at the pores edges.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Room-temperature synthesis of three-dimensional porous ZnO@CuNi hybrid magnetic layers with photoluminescent and photocatalytic properties

  • Guerrero, Miguel|||0000-0001-8350-8261
  • Zhang, Jin
  • Altube, Ainhoa
  • García-Lecina, Eva|||0000-0001-8915-840X
  • Roldán, Mónica
  • Pellicer, Eva|||0000-0002-8901-0998
  • Baró, M. D.|||0000-0002-8636-1063
  • Sort, Jordi|||0000-0003-1213-3639
A facile synthetic approach to prepare porous ZnO@CuNi hybrid films is presented. Initially, magnetic CuNi porous layers (consisting of phase separated CuNi alloys) are successfully grown by electrodeposition at different current densities using H₂ bubbles as a dynamic template to generate the porosity. The porous CuNi alloys serve as parent scaffolds to be subsequently filled with a solution containing ZnO nanoparticles previously synthesized by sol-gel. The dispersed nanoparticles are deposited dropwise onto the CuNi frameworks and the solvent is left to evaporate while the nanoparticles impregnate the interior of the pores, rendering ZnO-coated CuNi 3D porous structures. No thermal annealing is required to obtain the porous films. The synthesized hybrid porous layers exhibit an interesting combination of tunable ferromagnetic and photoluminescent properties. In addition, the aqueous photocatalytic activity of the composite is studied under UV-visible light irradiation for the degradation of Rhodamine B. The proposed method represents a fast and inexpensive approach towards the implementation of devices based on metal-semiconductor porous systems, avoiding the use of post-synthesis heat treatment steps which could cause deleterious oxidation of the metallic counterpart, as well as collapse of the porous structure and loss of the ferromagnetic properties.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrochemical synthesis of bismuth particles, tuning particle shape through substrate type within a narrow potential window

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Reusable and long-lasting active micro-cleaners for heterogeneous water remediation

  • Parmar, Jemish
  • Vilela, Diana
  • Pellicer, Eva|||0000-0002-8901-0998
  • Esqué-de los Ojos, Daniel|||0000-0002-6279-2037
  • Sort, Jordi|||0000-0003-1213-3639
  • Sánchez Ordóñez, Samuel|||0000-0001-9713-9997
Self-powered micro-machines are promising tools for the future environmental remediation technology. Waste water treatment and water reuse is an essential part of environmental sustainability. Herein, we present reusable Fe/Pt multi-functional active micro-cleaners that are capable of degrading organic pollutants by generated hydroxyl radicals via Fenton-like reaction. Various different properties of micro-cleaners such as the effect of their size, short-term storage, long-term storage, reusability, continuous swimming capability, surface composition and mechanical properties are studied. We find that micro-cleaners can continuously swim for more than 24 hours and can be stored more than 5 weeks during multiple cleaning cycles. Micro-cleaners can also be reused, which reduces the cost of the process. Over the reuse cycles, the outer iron surface of the Fe/Pt micro-cleaners generates in-situ heterogeneous Fenton catalyst and releases a low concentration of iron into the treated water while the mechanical properties also appear to be improved due to both surface composition and structural changes. Results have been characterized by SEM, XPS, Nanoindentation and Finite Element Modeling (FEM).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Toward robust segmented nanowires, understanding the impact of crystallographic texture on the quality of segment interfaces in magnetic metallic nanowires

  • Zhang, Jin
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Segmented nanowires (NWs) have found a wealth of applications due to their multifuctionality, arising from complementarities and synergies among segments of different materials. However, to ensure a practical use of segmented NWs, high quality interfaces between dissimilar segments must be ensured. Herein, tri-segmented CoPt/Cu/Ni NWs and bi-segmented CoPt/Ni magnetic NWs are fabricated by means of template-assisted electrodeposition and the characteristics of their interfaces are investigated in detail. The presence of a Cu segment sandwiched between the CoPt and the Ni segments severely affects the integrity of the whole NW. Namely, Cu deposits in a (200) textured face-centered cubic (fcc) structure, which cannot accommodate well on the c-axis oriented hexagonal close-packed CoPt. Instead, when the Cu segment is absent, well-connected CoPt/Ni NWs with smooth interface are obtained. Unlike the Cu segment, Ni shows the (111) textured fcc structure, which holds good crystallographic matching with the underlying CoPt segment. Magnetic measurements reveal that CoPt/Ni NWs exhibit staircase-like hysteresis loops similar to the tri-segmented CoPt/Cu/Ni NWs. Such loop shape stems from the dissimilar coercivity between the hard (CoPt) and soft (Ni) segments. The bi-segmented NWs (with robust interfaces) are appealing for multi-bit recording media, magnetic nanoelectromechanical systems and magnetically-driven wireless drug delivery nanoplatforms.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Sub-micron magnetic patterns and local variations of adhesion force induced in non-ferromagnetic amorphous steel by femtosecond pulsed laser irradiation

  • Zhang, Huiyan
  • Feng, Yuping
  • Nieto, Daniel
  • García-Lecina, Eva|||0000-0001-8915-840X
  • Mcdaniel, Clare
  • Díaz Marcos, Jordi
  • Flores-Arias, María Teresa
  • O'connor, Gerard M.
  • Baró, M. D.|||0000-0002-8636-1063
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Periodic ripple and nanoripple patterns are formed at the surface of amorphous steel after femtosecond pulsed laser irradiation (FSPLI). Formation of such ripples is accompanied with the emergence of a surface ferromagnetic behavior which is not initially present in the non-irradiated amorphous steel. The occurrence of ferromagnetic properties is associated with the laser-induced devitrification of the glassy structure to form ferromagnetic (α-Fe and Fe₃C) and ferrimagnetic [(Fe,Mn)₃O₄ and Fe₂CrO4] phases located in the ripples. The generation of magnetic structures by FSPLI turns out to be one of the fastest ways to induce magnetic patterning without the need of any shadow mask. Furthermore, local variations of the adhesion force, wettability and nanomechanical properties are also observed and compared to those of the as-cast amorphous alloy. These effects are of interest for applications (e.g., biological, magnetic recording, etc.) where both ferromagnetism and tribological/adhesion properties act synergistically to optimize material performance.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrodeposition of sizeable and compositionally tunable rhodium-iron nanoparticles and their activity toward hydrogen evolution reaction

  • Golvano Escobal, Irati|||0000-0001-8518-8185
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Baró, M. D.|||0000-0002-8636-1063
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Rh-Fe nanoparticles (NPs) with variable Rh/Fe ratios have been obtained by direct current electrodeposition onto Au-metalized Si/Ti substrates from an electrolyte containing Rh(III) and Fe(III) chloride salts. NP mean diameter could be varied in the range of 20-80 nm by playing with the applied current density (-j = 0.5-2 mA cm-2) and deposition times (t = 200-3200 s). NPs were very well adhered to the substrate and became progressively enriched in Fe as the absolute value of the current density increased. X-ray photoelectron spectroscopy analyses revealed that the NPs are mostly metallic. The oxygen signal detected at surface level is relatively high but reduces down to less than 1 at% after 1 min Ar ions sputtering. The as-deposited Rh-Fe NPs are active toward hydrogen evolution reaction in alkaline medium. Different values of the onset potential for water reduction have been observed depending on the j and t values applied for NPs growth. Cycling stability tests reveal that NPs do not suffer from excessive deterioration of their electrocatalytic activity with time.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrochemical deposition of NiMnGa alloys

  • Özkale, Berna|||0000-0002-3016-9363
  • Mushtaq, Fajer
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Sort, Jordi|||0000-0003-1213-3639
  • Muller Jevenois, Carlos
  • Pellicer, Eva|||0000-0002-8901-0998
An electrochemical synthesis route for NiMnGa alloys is presented. Thin films (TFs) of NiMnGa were fabricated by single step electrodeposition from aqueous electrolytes using direct current (DC) over a range of current densities. By meticulous electrolyte tuning, homogeneous TFs with high Ga and Mn content could be achieved at current densities as high as -400 mA cm-2. Detailed compositional analysis of the alloys showed that growth was homogeneous and oxygen content was minimized. TFs plated at very low current densities were found to be nanocrystalline/ amorphous. In order to obtain fully crystalline samples, thermal annealing was carried out. Mechanical characterization was assessed by nanoindentation, and the effect of Ga content on mechanical properties was investigated.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Novel Fe-Mn-Si-Pd alloys: insights on mechanical, magnetic, corrosion performance and biocompatibility

  • Feng, Yuping
  • Blanquer, Andreu|||0000-0002-3551-1885
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Zhang, Huiyan
  • Solsona, Pau|||0000-0001-9274-2447
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Ibáñez, Elena|||0000-0002-0275-6958
  • Barrios, Leonardo|||0000-0002-6151-8503
  • Pellicer, Eva|||0000-0002-8901-0998
  • Nogués, Carme|||0000-0002-6361-8559
  • Sort, Jordi|||0000-0003-1213-3639
Two new Fe-based alloys, Fe-10Mn6Si1Pd and Fe-30Mn6Si1Pd, have been fabricated by arc-melting followed by copper mold suction casting. The Fe-30Mn6Si1Pd alloy mainly consists of ε-martensite and γ-austenite Fe-rich phases whereas the Fe-10Mn6Si1Pd alloy primarily contains α-Fe(Mn)-ferrite phase. Additionally, Pd-rich precipitates were detected in both alloys. Good mechanical response was observed by nanoindentation: hardness values around 5.6 GPa and 4.2 GPa and reduced Young's modulus values of 125 GPa and 93 GPa were measured for the as-prepared Fe-10Mn6Si1Pd and Fe-30Mn6Si1Pd alloys, respectively. Both alloys are thus harder and exhibit lower Young's modulus than 316L stainless steel, which is one of the most common Fe-based reference materials for biomedical applications. Compared with the ferromagnetic Fe-10Mn6Si1Pd alloy, the paramagnetic Fe-30Mn6Si1Pd alloy is more appropriate to be used as an implant since it would be compatible with nuclear magnetic resonance (NMR) and magnetic resonance imaging (MRI) analyses. Concerning biocompatibitliy, the more hydrophilic Fe-10Mn6Si1Pd shows improved cell adhesion but its pronounced ion leaching has a negative effect on the proliferation of cells. The influence of immersion in simulated body fluid on composition, microstructure, mechanical and magnetic properties of both alloys is assessed, and the correlation between microstructure evolution and physical properties is discussed.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Conformal oxide nanocoatings on electrodeposited 3D porous Ni films by atomic layer deposition

  • Zhang, Jin
  • Coll, Maria Dolors
  • Puig i Molina, Mª Teresa|||0000-0002-1873-0488
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
A versatile chemical synthesis procedure to obtain Al2O3 and Co2FeO4 nanolayers conformally coating a three-dimensional (3D) porous Ni film is presented. First, porous Ni is grown by hydrogen bubble template-assisted electrodeposition. Subsequently, Al2O3 and Co2FeO4 layers, with thickness ranging from 5 nm to 25 nm, are directly deposited onto the pore walls by atomic layer deposition, while maintaining the porous architecture and magnetic properties of the Ni scaffold. The crystal structure, thickness and distribution of elements within the composite coatings are investigated in detail. The resulting magnetic and wettability properties are assessed. Contact angle tests reveal that 3D porous Ni films become more hydrophilic after coating with Al2O3 or Co2FeO4. From a technological point of view, the obtained composite porous films could be appealing for applications like magnetically-actuated micro/nano-electromechanical systems (MEMS/NEMS) or bio-MEMS/NEMS, among others.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Cross-sectioning spatio-temporal Co-In electrodeposits: disclosing a magnetically-patterned nanolaminated structure

  • Golvano Escobal, Irati|||0000-0001-8518-8185
  • Sirvent, Juan de Dios
  • Ferran, Marta|||0000-0003-1198-0641
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Baró, M. D.|||0000-0002-8636-1063
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Micrometer-thick cobalt-indium (Co-In) films consisting of self-assembled layers parallel to the cathode plane, and with a periodicity of 175 ± 25 nm, have been fabricated by electrodeposition at a constant current density. These films, which exhibit spatio-temporal patterns on the surface, grow following a layer-by-layer mode. Films cross-sections were characterized by electron microscopies and electron energy loss spectroscopy. Results indicate the spontaneous formation of nanolayers that span the whole deposit thickness. A columnar structure was revealed inside each individual nanolayer which, in turn, was composed of well-distinguished In- and Co-rich regions. Due to the dissimilar magnetic character of these regions, a periodic magnetic nanopatterning was observed in the cross-sectioned films, as shown by magnetic force microscopy studies.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanomechanical behaviour of open-cell nanoporous metals: homogeneous versus thickness-dependent porosity

  • Esqué-de los Ojos, Daniel|||0000-0002-6279-2037
  • Zhang, Jin
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Two dierent nanoporous materials, porous copper prepared by dealloying and porous nickel prepared by electrodeposition, have been studied by means of nanoindentation experiments at dierent maximum applied loads. While nanoporous Cu is homogeneous along its cross-section, the electrodeposited Ni lms show a graded porosity, with smaller pores and thicker pore walls close to the lm's surface. The mechanical properties of the two materials have been extracted using a methodology based on scaling laws and subsequent interpretation has been performed using nite element simulations. Two dierent deformation mechanisms are observed for nanoporous Cu and nanoporous Ni, respectively. Dealloyed porous copper behaves as an homogeneous material without evident eect of densication and with mechanical properties that are independent of the applied load. Given this homogeneity, it is possible to t the entire loading - unloading curve for dierent maximum applied loads with a single set of mechanical properties. Conversely, electrodeposited porous nickel shows a decrease in the reduced Young's modulus, an increase in yield stress and a constant hardness when the maximum applied load during nanoindentation is increased. While the decrease in the reduced Young's modulus can be explained in the context of thickness inhomogeneity of the electrodeposited porous nickel (i.e., increase of porosity with depth), this cannot explain, and actually would go against, the observed increase in the yield stress, which is instead associated to the decrease in the ligament size.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanocasting synthesis of mesoporous SnO₂ with a tunable ferromagnetic response through Ni loading

  • Fan, Junpeng|||0000-0003-2243-5251
  • Zhang, Jin
  • Solsona, Pau|||0000-0001-9274-2447
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Baró, M. D.|||0000-0002-8636-1063
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Undoped and Ni-doped ordered mesoporous SnO₂ powders ([Ni(II)]/[Sn(II)] = 0 : 100, 5 : 95, 15 : 85, 20 : 80) were synthesized by nanocasting from mesoporous KIT-6 silica. The resulting Ni content in the Ni-loaded powders ranged between 1 at% and 9 at%. Successful replication of the silica template was verified by scanning electron microscopies for all samples. Residual silicon content did not surpass 4 at%. X-ray diffraction analyses showed that the powders were nanocrystalline, being the rutile-like phase of SnO₂ the dominant structure. Changes in the lattice constants depending on the Ni content were observed, suggesting that Ni enters the rutile structure of SnO₂ to some extent. No extra phases attributed to Ni were detected in the powders except for the sample synthesized from 20 : 80 [Ni(II)]/[Sn(II)], for which NiO as secondary phase was observed. The oxidation state and spatial distribution of Ni in the powders was investigated by X-ray photoelectron spectroscopy (XPS) and electron energy loss spectroscopy (EELS) measurements, respectively. For 6 at% and 9 at% Ni content, the presence of Ni2+ was established. The corresponding EELS mapping showed that a fraction of Ni (the one not forming part of the rutile phase) tended to accumulate at the pore edges, forming a nanometer-thick NiO layer. Compared to undoped SnO₂, Ni-containing powders exhibit a ferromagnetic response at low and room temperatures. Uncompensated spins at the surface of NiO are likely to contribute, in part, to the observed ferromagnetic properties.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanoindenting the Chelyabinsk meteorite to learn about impact deflection effects in asteroids

  • Moyano-Cambero, Carles Eduard|||0000-0002-1543-8377
  • Pellicer, Eva|||0000-0002-8901-0998
  • Trigo-Rodríguez, J.M.|||0000-0001-8417-702X
  • Williams, Iwan P.
  • Blum, Jürgen
  • Michel, Patrick
  • Küppers, Michael
  • Martínez-Jiménez, Marina
  • Lloro, Ivan|||0000-0001-5966-1434
  • Sort, Jordi|||0000-0003-1213-3639
The Chelyabinsk meteorite is a highly shocked, low porosity, ordinary chondrite, probably similar to S- or Q-type asteroids. Therefore, nanoindentation experiments on this meteorite allow us to obtain key data to understand the physical properties of near-Earth asteroids (NEAs). Tests at different length scales provide information about the local mechanical properties of the minerals forming this meteorite: reduced Young's modulus, hardness, elastic recovery, and fracture toughness. Those tests are also useful to understand the potential to deflect threatening asteroids using a kinetic projectile. We found that the differences in mechanical properties between regions of the meteorite, which increase or reduce the efficiency of impacts, are not a result of compositional differences. A low mean particle size, attributed to repetitive shock, can increase hardness, while low porosity promotes a higher momentum multiplication. Momentum multiplication is the ratio between the change in momentum of a target due to an impact, and the momentum of the projectile, and therefore higher values imply more efficient impacts. In the Chelyabinsk meteorite the properties of the light-colored lithology materials facilitate obtaining higher momentum multiplication values, compared to the other regions described for this meteorite. Also, we found a low value of fracture toughness in the shock-melt veins of Chelyabinsk, which would promote the ejection of material after an impact and therefore increase the momentum multiplication. These results are relevant in the context of a future mission to test asteroid deflection, currently being studied by ESA and NASA: the Asteroid Impact and Deflection Assessment (AIDA) mission.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Spontaneous formation of spiral-like patterns with distinct periodic physical properties by confined electrodeposition of Co-In disks

  • Golvano Escobal, Irati|||0000-0001-8518-8185
  • Gonzalez-Rosillo, Juan Carlos
  • Domingo Marimon, Neus|||0000-0002-5229-6638
  • Illa, Xavi|||0000-0002-3212-1128
  • López-Barbera, José Francisco|||0000-0002-9475-625X
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Solsona, Pau|||0000-0001-9274-2447
  • Aballe, Lucía|||0000-0003-1810-8768
  • Foerster, Michael|||0000-0002-4147-6668
  • Baró, M. D.|||0000-0002-8636-1063
  • Puig i Molina, Mª Teresa|||0000-0002-1873-0488
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Nogués, Josep|||0000-0003-4616-1371
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Spatio-temporal patterns are ubiquitous in different areas of materials science and biological systems. However, typically the motifs in these types of systems present a random distribution with many possible different structures. Herein, we demonstrate that controlled spatio-temporal patterns, with reproducible spiral-like shapes, can be obtained by electrodeposition of Co-In alloys inside a confined circular geometry (i.e., in disks commensurate with the typical size of the spatio-temporal features). These patterns are mainly of compositional nature, i.e., with virtually no topographic features. Interestingly, the local changes in composition lead to a periodic modulation of the physical (electric, magnetic and mechanical) properties. Namely, the Co-rich areas show higher saturation magnetization and electrical conductivity and are mechanically harder than the In-rich ones. Thus, this work reveals that confined electrodeposition of this binary system constitutes an effective procedure to attain template-free magnetic, electric and mechanical surface patterning with specific and reproducible shapes.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Effect of surface modifications of Ti40Zr10Cu38Pd12 bulk metallic glass and Ti-6Al-4V alloy on human osteoblasts in vitro biocompatibility

  • Blanquer, Andreu|||0000-0002-3551-1885
  • Hynowska, Anna
  • Nogués, Carme|||0000-0002-6361-8559
  • Ibáñez, Elena|||0000-0002-0275-6958
  • Sort, Jordi|||0000-0003-1213-3639
  • Baró, M. D.|||0000-0002-8636-1063
  • Özkale, Berna|||0000-0002-3016-9363
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Pellicer, Eva|||0000-0002-8901-0998
  • Barrios, Leonardo|||0000-0002-6151-8503
The use of biocompatible materials, including bulk metallic glasses (BMGs), for tissue regeneration and transplantation is increasing. The good mechanical and corrosion properties of Ti40Zr10Cu38Pd12 BMG and its previously described biocompatibility makes it a potential candidate for medical applications. However, it is known that surface properties like topography might play an important role in regulating cell adhesion, proliferation and differentiation. Thus, in the present study, Ti40Zr10Cu38Pd12 BMG and Ti6-Al-4V alloy were surface-modified electrochemically (nanomesh) or physically (microscratched) to investigate the effect of material topography on human osteoblasts cells (Saos-2) adhesion, proliferation and differentiation. For comparative purposes, the effect of mirror-like polished surfaces was also studied. Electrochemical treatments led to a highly interconnected hierarchical porous structure rich in oxides, which have been described to improve corrosion resistance, whereas microscratched surfaces showed a groove pattern with parallel trenches. Cell viability was higher than 96% for the three topographies tested and for both alloy compositions. In all cases, cells were able to adhere, proliferate and differentiate on the alloys, hence indicating that surface topography plays a minor role on these processes, although a clear cell orientation was observed on microscratched surfaces. Overall, our results provide further evidence that Ti40Zr10Cu38Pd12 BMG is an excellent candidate, in the present two topographies, for bone repair purposes.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Biodegradable FeMnSi sputter-coated macroporous polypropylene membranes for the sustained release of drugs

  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Soriano Martín, Jorge|||0000-0003-3295-7643
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Sirvent, Juan de Dios
  • Ferran, Marta|||0000-0003-1198-0641
  • Ibáñez, Elena|||0000-0002-0275-6958
  • Barrios, Leonardo|||0000-0002-6151-8503
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Nogués, Carme|||0000-0002-6361-8559
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Pure Fe and FeMnSi thin films were sputtered on macroporous polypropylene (PP) membranes with the aim to obtain biocompatible, biodegradable and, eventually, magnetically-steerable platforms. Room-temperature ferromagnetic response was observed in both Fe- and FeMnSi-coated membranes. Good cell viability was observed in both cases by means of cytotoxicity studies, though the FeMnSi-coated membranes showed higher biodegradability than the Fe-coated ones. Various strategies to functionalize the porous platforms with transferrin-Alexa Fluor 488 (Tf-AF488) molecules were tested to determine an optimal balance between the functionalization yield and the cargo release. The distribution of Tf-AF488 within the FeMnSi-coated PP membranes, as well as its release and uptake by cells, was studied by confocal laser scanning microscopy. A homogeneous distribution of the drug within the membrane skeleton and its sustained release was achieved after three consecutive impregnations followed by the addition of a layer made of gelatin and maltodextrin, which prevented exceedingly fast release. The here-prepared organic-inorganic macroporous membranes could find applications as fixed or magnetically-steerable drug delivery platforms.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrodeposited Ni-based magnetic mesoporous films as smart surfaces for atomic layer deposition: an 'all-chemical' deposition approach toward 3D nanoengineered composite layers

  • Zhang, Jin
  • Quintana, Alberto|||0000-0002-9813-735X
  • Menéndez, Enric|||0000-0003-3809-2863
  • Coll, Maria Dolors
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Mesoporous Ni and Cu-Ni (Cu₂₀Ni₈₀ and Cu₄₅Ni₅₅ in at. %) films, showing a three-dimensional (3D) porous structure and tunable magnetic properties, are prepared by electrodeposition from aqueous surfactant solutions using micelles of P-123 triblock copolymer as structure-directing entities. Pores between 5 and 30 nm and dissimilar space arrangements (continuous interconnected networks, circular pores, corrugated mesophases) are obtained depending on the synthetic conditions. X-ray diffraction studies reveal that the Cu-Ni films have crystallized in the face-centered cubic structure, are textured, and exhibit certain degree of phase separation, particularly those with a higher Cu content. Atomic layer deposition (ALD) is used to conformally coat the mesopores of Cu₂₀Ni₈₀ film with amorphous Al₂O₃, rendering multiphase "nano-in-meso" metal-ceramic composites without compromising the ferromagnetic response of the metallic scaffold. From a technological viewpoint, these 3D nanoengineered composite films could be appealing for applications like magnetically actuated micro/nanoelectromechanical systems (MEMS/NEMS), voltage-driven magneto-electric devices, capacitors, or as protective coatings with superior strength and tribological performance.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanoporous Fe-based alloy prepared by selective dissolution, an effective Fenton catalyst for water remediation

  • Zhang, Huiyan
  • Feng, Yuping
  • Cheng, Yangyang
  • Baró, M. D.|||0000-0002-8636-1063
  • Altube, Ainhoa
  • García-Lecina, Eva|||0000-0001-8915-840X
  • Alcaide, Francisco|||0000-0002-3373-3978
  • Pellicer, Eva|||0000-0002-8901-0998
  • Zhang, Tao
  • Sort, Jordi|||0000-0003-1213-3639
A fully nanoporous Fe-rich alloy, prepared by selective dissolution of melt-spun Fe₄₃.₅Cu₅₆.₅ ribbons, exhibits outstanding properties as a heterogeneous Fenton catalyst toward the degradation of methyl orange (MO) in aqueous solution. In addition, the ferromagnetic characteristics of this material enable its wireless manipulation toward specific locations within polluted wastewater. The influence of selective dissolution on the microstructure, sample morphology (surface and cross-section), elemental composition, and magnetic properties of the resulting nanoporous alloy is investigated. The dealloying procedure enhances the saturation magnetization and drastically increases the catalytic performance (i.e., the time required for full degradation of MO from the medium is reduced by a factor of approximately 2 by subjecting the Fe43.5Cu56.5 ribbons to prior dealloying). Remarkably, the effectiveness of this nanoporous material surpasses the results obtained by the homogeneous Fenton reaction using an equivalent concentration of Fe cations leached into the media from the nanoporous alloy. The different factors that promote the high catalytic activity are discussed. The outstanding catalytic activity, together with the simplicity of the synthetic procedure, makes this material very appealing for water remediation using advanced Fenton processes.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Fabrication of sustainable hydrophobic and oleophilic pseudo-ordered macroporous Fe-Cu films with tunable composition and pore size via electrodeposition through colloidal templates

  • Dislaki, Evangelia|||0000-0002-3360-1588
  • Pokki, Juho
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
In this work, sustainable hydrophobic and oleophilic macroporous Fe-Cu films are fabricated using a straightforward, inexpensive and environmentally friendly two-step procedure which combines electrodeposition with the colloidal lithography technique. Elemental, morphological and structural characterization of the resulting pseudo-ordered meshes is carried out and wettability is assessed using contact angle measurements with respect to two distinct film compositions (3 at.% Fe vs 75-85 at.% Fe) and three different pore diameters (namely, 200 nm, 350 nm and 500 nm). Water contact angles are measured to be in the range of approximately 109.0-155.1° (without any post-surface functionalization) and a low contact angle hysteresis is observed in the superhydrophobic samples. The increase in the hydrophobic character of the films correlates well with an increase in surface roughness, whereas differences in composition play a minor role. For the superhydrophobic Fe-rich macroporous film, water-oil separation capability and recyclability are also demonstrated while the pore size is favorable for effective water-oil mixture and emulsion separation. The results shown here demonstrate that sustainable and affordable materials processed in a simple and cheap manner can be an asset for the removal of water-immiscible organic compounds from aqueous environments.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Micelle-assisted electrodeposition of mesoporous Fe-Pt smooth thin films onto various substrates and their electrocatalytic activity towards hydrogen evolution reaction

  • Isarain-Chávez, Eloy|||0000-0002-4154-1343
  • Baró, M. D.|||0000-0002-8636-1063
  • Alcantara, Carlos
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Mesoporous Fe-Pt thin films are obtained by micelle-assisted electrodeposition onto metallic substrates with dissimilar activity (namely, gold, copper, and aluminum seed layers evaporated on Si/Ti) under constant applied potential (E=-1.1 V vs. Ag/AgCl) and deposition time (600 s). The amphiphilic triblock copolymer Pluronic P-123 is used as a soft template to guide the formation of mesopores. The occurrence of pores (ca. 7 nm in diameter) with narrow size distribution, distributed evenly over the surface, is observed in all cases. Despite the applied conditions being the same, the roughness and the amount of Fe incorporated in the films are influenced by the nature of the substrate. In particular, ultra-smooth films containing a larger amount of Fe (21 wt %) are obtained when deposition takes place on the Au surface. X-ray diffraction analyses reveal that Pt and Fe are alloyed to a certain extent, although some iron oxides/hydroxides also unavoidably form. The resulting films have been tested as electrocatalysts in the hydrogen evolution reaction (HER) in alkaline media. The mesoporous Fe-rich Fe-Pt films on Au show excellent HER activity and cyclability.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Parametric aqueous electrodeposition study and characterization of Fe-Cu films

  • Dislaki, Evangelia|||0000-0002-3360-1588
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
In this study, FexCu1-x films over a wide composition range (0≤x≤86) were prepared from an aqueous sulfate electrolytic solution using three different complexing agents and variable plating conditions. The effect of parameters such as bath composition, current density and temperature on the elemental composition, morphology, structure and magnetic properties of the deposits was investigated. The electrochemical behavior was studied using cyclic voltammetry. High quality, smooth deposits with good substrate adhesion and minimized oxygen content were achieved. X-ray patterns indicate phase separation, though results from Rietveld analysis strongly suggest partial alloying. Magnetization dependence on Fe content is clearly demonstrated.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A facile co-precipitation synthesis of heterostructured ZrO₂/ZnO nanoparticles as efficient photocatalysts for wastewater treatment

  • Quintana, Alberto|||0000-0002-9813-735X
  • Altube, Ainhoa
  • García-Lecina, Eva|||0000-0001-8915-840X
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Baró, M. D.|||0000-0002-8636-1063
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
  • Guerrero, Miguel|||0000-0001-8350-8261
ZrO₂-decorated ZnO (ZrO₂/ZnO) nanoparticles (NPs) have been synthesized by a facile co-precipitation method in the presence of cetyltrimethylammonium bromide (CTAB) surfactant. The ZrO₂ amount in the NPs has been varied from 1.0, 2.0, 4.9, to 9.3% by weight. The resulting NPs are heterostructured and consist of a crystalline ZnO core (wurtzite phase) surrounded by an amorphous ZrO₂ layer. X-ray diffraction analyses support this observation. The NPs show a narrow size distribution and are slightly elongated. Compared to pure ZnO NPs, the hybrid ZrO₂/ZnO ones show enhanced photocatalytic activity toward the degradation of Rhodamine B under UV-Vis light. Such enhancement has been partly attributed to the increased amount of oxygen vacancies when ZrO₂ is incorporated into the NPs, as shown by X-ray photoelectron spectroscopy analyses.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Mechanical properties, corrosion performance and cell viability studies on newly developed porous Fe-Mn-Si-Pd alloys

  • Feng, Yuping
  • Gaztelumendi, Nerea|||0000-0002-3837-2956
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Zhang, Huiyan
  • Solsona, Pau|||0000-0001-9274-2447
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Ibáñez, Elena|||0000-0002-0275-6958
  • Barrios, Leonardo|||0000-0002-6151-8503
  • Pellicer, Eva|||0000-0002-8901-0998
  • Nogués, Carme|||0000-0002-6361-8559
  • Sort, Jordi|||0000-0003-1213-3639
Porous Fe-30Mn6Si1Pd (wt.%) alloys were prepared by a simple press and sinter process from ball-milled Fe, Mn, Si and Pd powders blended with 10 wt%, 20 wt% and 40 wt% NaCl to obtain different degrees of porosity. For comparison purposes, a bulk fully-compact Fe-30Mn6Si1Pd alloy was produced by arc-melting and subsequent copper-mold suction-casting. While the porous Fe-30Mn6Si1Pd alloys only consist of γ-austenite, their fully-compact counterpart comprises ε-martensite and γ-austenite phases. In all cases, the low magnetic susceptibility response assures good compatibility with nuclear magnetic resonance and magnetic resonance imaging techniques. Furthermore, a reduction of the Young's modulus, from 55 to 7 GPa, was attained by introducing porosity. The biodegradation performance was evaluated by static immersion and electrochemical corrosion tests in Hank's solution. The influence of immersion time on composition, microstructure, mechanical and magnetic properties was assessed. While introducing porosity renders alloys with suitable mechanical and magnetic properties, it also has a detrimental effect in terms of cell viability. Hence, the porosity level needs to be controlled in order to obtain alloys with an optimized performance.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Evaporation-induced self-assembly synthesis of Ni-doped mesoporous SnO₂ thin films with tunable room temperature magnetic properties

  • Fan, Junpeng|||0000-0003-2243-5251
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Carretero-Genevrier, Adrian|||0000-0003-0488-9452
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Mesoporous Ni-doped SnO₂ thin films synthesized from variable [Ni(II)/Sn(IV)] molar ratios (0 : 100, 5 : 95, 10 : 90, 15 : 85 and 20 : 80), thicknesses in the range of 100-150 nm, and average pore sizes lower than 10 nm were obtained through a sol-gel based self-assembly process using Pluronic P-123 as a structure-directing agent. Grazing incidence X-ray diffraction experiments indicate that the films mostly possess a tetragonal SnO₂ structure with Ni²+ in substitutional positions, although energy-dispersive X-ray analyses also reveal the occurrence of small NiO clusters in the films produced from high [Ni(II)/Sn(IV)] molar ratios (corresponding to a Ni amount of 8.6 at%). X-ray photoelectron spectroscopy experiments indicate the lack of metallic Ni and the occurrence of oxygen vacancies in the mesoporous films. Interestingly, the magnetic properties of these mesoporous films significantly vary as a function of the doping percentage. The undoped SnO₂ films exhibit a diamagnetic behavior, whereas a clear paramagnetic signal dominates the magnetic response of the Ni-doped mesoporous films, probably due to the presence of NiO as a secondary phase. A small ferromagnetic-like contribution superimposed to the paramagnetic background is observed for samples with high Ni contents, possibly stemming from the combined effect from Ni incorporation and the occurrence of oxygen vacancies.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Voltage-induced coercivity reduction in nanoporous alloy films, a boost towards energy-efficient magnetic actuation

  • Quintana, Alberto|||0000-0002-9813-735X
  • Zhang, Jin
  • Isarain-Chávez, Eloy|||0000-0002-4154-1343
  • Menéndez, Enric|||0000-0003-3809-2863
  • Quadrado del Burgo, Ramón|||0000-0002-8344-2319
  • Robles, Roberto|||0000-0001-7808-0395
  • Baró, M. D.|||0000-0002-8636-1063
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Nelson, Bradley J.|||0000-0001-9070-6987
  • Muller Jevenois, Carlos
  • Ordejon, Pablo|||0000-0002-2353-2793
  • Nogués, Josep|||0000-0003-4616-1371
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Magnetic data storage and magnetically actuated devices are conventionally controlled by magnetic fields generated using electric currents. This involves significant power dissipation by Joule heating effect. To optimize energy efficiency, manipulation of magnetic information with lower magnetic fields (i.e., lower electric currents) is desirable. This can be accomplished by reducing the coercivity of the actuated material. Here, a drastic reduction of coercivity is observed at room temperature in thick (≈600 nm), nanoporous, electrodeposited Cu-Ni films by simply subjecting them to the action of an electric field. The effect is due to voltage-induced changes in the magnetic anisotropy. The large surface-area-to-volume ratio and the ultranarrow pore walls of the system allow the whole film, and not only the topmost surface, to effectively contribute to the observed magnetoelectric effect. This waives the stringent "ultrathin-film requirement" from previous studies, where small voltage-driven coercivity variations were reported. This observation expands the already wide range of applications of nanoporous materials (hitherto in areas like energy storage or catalysis) and it opens new paradigms in the fields of spintronics, computation, and magnetic actuation in general.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Self-templating faceted and spongy single-crystal ZnO nanorods, resistive switching and enhanced piezoresponse

  • Quintana, Alberto|||0000-0002-9813-735X
  • Gómez, Andrés|||0000-0003-2847-0138
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
A template-free, cost-effective, hydrothermal procedure is used to synthesize large areas of either faceted or spongy self-standing single-crystalline ZnO nanorods (NRs) from electrodeposited Zn films. The morphology of the NRs (faceted versus spongy) can be easily adjusted by simply varying the electrodeposition parameters of the parent Zn film. The obtained NRs exhibit an enhanced piezoelectric response (compared to bulk ZnO) and resistive switching properties which depend on their intrinsic morphology. This combination of properties together with the simplicity of the synthetic approach is particularly appealing for the fabrication of large arrays of nanosensors, nanoactuators and other applications that could benefit from an enhanced surface area in single-crystalline semiconductors.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Unraveling the origin of magnetism in mesoporous Cu-doped SnO₂ magnetic semiconductor

  • Fan, Junpeng|||0000-0003-2243-5251
  • Menéndez, Enric|||0000-0003-3809-2863
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Quintana, Alberto|||0000-0002-9813-735X
  • Weschke, Eugen
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
The origin of magnetism in wide-gap semiconductors doped with non-ferromagnetic 3d transition metals still remains intriguing. In this article, insights in the magnetic properties of ordered mesoporous Cu-doped SnO₂ powders, prepared by hard-templating, have been unraveled. Whereas, both oxygen vacancies and Fe-based impurity phases could be a plausible explanation for the observed room temperature ferromagnetism, the low temperature magnetism is mainly and unambiguously arising from the nanoscale nature of the formed antiferromagnetic CuO, which results in a net magnetization that is reminiscent of ferromagnetic behavior. This is ascribed to uncompensated spins and shape-mediated spin canting effects. The reduced blocking temperature, which resides between 30 and 5 K, and traces of vertical shifts in the hysteresis loops confirm size effects in CuO. The mesoporous nature of the system with a large surface-to-volume ratio likely promotes the occurrence of uncompensated spins, spin canting, and spin frustration, offering new prospects in the use of magnetic semiconductors for energy-efficient spintronics.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Micelle-assisted electrodeposition of highly mesoporous Fe-Pt nodular films with soft magnetic and electrocatalytic properties

  • Isarain-Chávez, Eloy|||0000-0002-4154-1343
  • Baró, M. D.|||0000-0002-8636-1063
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Mesoporous Fe-Pt nodular films (with a regular spatial arrangement of sub-15 nm pores) are grown onto evaporated Au, Cu and Al conductive layers by micelle-assisted electrodeposition from metal chloride salts in the presence of Pluronic P123 tri-block copolymer dissolved in the aqueous electrolytic bath. This synthetic approach constitutes a simple, one-step, versatile procedure to grow multifunctional mesoporous layers appealing for diverse applications that take advantage of materials with an ultra-high surface area-to-volume ratio. The films exhibit tuneable composition with relative Fe/Pt weight ratios, disregarding oxygen, varying from 4/96 to 52/48. All the mesoporous alloys show a soft magnetic behaviour with tuneable saturation magnetization and coercivity values (the latter ranging from ca. 5 Oe to 40 Oe). In addition, the Au/Fe-Pt deposits (even the ones with higher Fe content) exhibit good performance towards hydrogen evolution reaction in both alkaline and acidic media due to the inherent mesoporosity, with excellent stability after running 50 cycles. The interest of alloying Fe with Pt is thus two-fold: (i) to confer magnetic properties to the mesoporous alloys and (ii) to reduce the amount of the costly noble metal in the electrocatalyst in an environmentally sustainable manner.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Mechanical behaviour of brushite and hydroxyapatite coatings electrodeposited on newly developed FeMnSiPd alloys

  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Feng, Yuping
  • Pellicer, Eva|||0000-0002-8901-0998
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Sort, Jordi|||0000-0003-1213-3639
Calcium phosphate coatings (CaP) (i.e., brushite and hydroxyapatite) were grown by pulsed current electrodeposition on FeMnSiPd alloys, a newly developed material proposed for biomedical implants. The electrolytic baths contained Ca(NO₃)₂·4H₂O and NH₄H₂PO₄ as precursors. Bath additives, such as H₂O₂ and NaOH, were used to promote hydroxyapatite (HAp) coating formation directly from the bath. The effect of the electrodeposition parameters on the structure, morphology and mechanical performance of the coatings was investigated. Increasing the electrodeposition time from 900s to 3600s resulted in an increase of HAp over the dominant brushite structure. Addition of 2000 ppm of NaOH or 3000 ppm of H₂O₂ also promoted an increase of HAp fraction when compared to the coatings obtained from the additive-free bath. Nonetheless, pure HAp was only achieved with the addition of 4000 ppm of NaOH to the electrolyte. The morphologies of the CaP particles in the coatings ranged from needle- to plate-like structures depending on the electrodeposition parameters and the resulting phases. The mechanical behaviour of the coatings was studied by scratch testing and nanoindentation. As a general trend, the Young's modulus and hardness values of the electrodeposited coatings were lower than those reported for fully-dense HAp, independently of the deposition conditions, because of the porous morphology of the coatings. No signs of cracking or delamination were observed during nanoindentation or scratch tests except for the coating prepared form the electrolyte containing 3000 ppm of H₂O₂.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Ferromagnetic-like behaviour in bismuth ferrite films prepared by electrodeposition and subsequent heat treatment

  • Bilican, Doğa|||0000-0002-9497-5065
  • Menéndez, Enric|||0000-0003-3809-2863
  • Solsona, Pau|||0000-0001-9274-2447
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Bismuth ferrite (BiFeO₃) films (10 μm in thickness) are synthesized by electrodeposition from a dimethylformamide bath containing Bi and Fe nitrate salts as precursors followed by heat treatment in air. Thermal treatments are needed to induce crystallisation of the as-deposited amorphous-like films. A detailed morphological, structural and magnetic characterisation evidences that BiFeO3 forms in a rather narrow temperature window (around 600 °C). At lower and higher temperatures, secondary binary and ternary oxides are also formed. Soft ferromagnetic-like behaviour is observed in all films, which presumably arises from the obtained nanoscale structure, which favours the occurrence of spin canting in the BiFeO₃ antiferromagnetic phase. The eventual contribution from secondary phases to the observed ferromagnetic-like response is also discussed. The obtained results are appealing for the integration of BiFeO₃ into devices that may require relatively thick films with an enhanced surface area-to-volume ratio. The growth of this type of material by techniques other than electrodeposition is not straightforward.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Tunable magnetism in nanoporous CuNi alloys by reversible voltage-driven element-selective redox processes

  • Quintana, Alberto|||0000-0002-9813-735X
  • Menéndez, Enric|||0000-0003-3809-2863
  • Isarain-Chávez, Eloy|||0000-0002-4154-1343
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Solsona, Pau|||0000-0001-9274-2447
  • Baró, M. D.|||0000-0002-8636-1063
  • Nogués, Josep|||0000-0003-4616-1371
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Voltage-driven manipulation of magnetism in electrodeposited 200 nm thick nanoporous single-phase solid solution Cu20 Ni80 (at%) alloy films (with sub 10 nm pore size) is accomplished by controlled reduction-oxidation (i.e., redox) processes in a protic solvent, namely 1 m NaOH aqueous solution. Owing to the selectivity of the electrochemical processes, the oxidation of the CuNi film mainly occurs on the Cu counterpart of the solid solution, resulting in a Ni-enriched alloy. As a consequence, the magnetic moment at saturation significantly increases (up to 33% enhancement with respect to the as-prepared sample), while only slight changes in coercivity are observed. Conversely, the reduction process brings Cu back to its metallic state and, remarkably, it becomes alloyed to Ni again. The reported phenomenon is fully reversible, thus allowing for the precise adjustment of the magnetic properties of this system through the sign and amplitude of the applied voltage.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Thermal treatment effect on the mechanical, tribological and corrosion properties of Ni-W alloy obtained by direct and pulse plating electrodeposition

  • Imaz, Naroa
  • Díez, J. A.
  • Grande, H.
  • García-Lecina, Eva|||0000-0001-8915-840X
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Ni-W electrodeposits have emerged as one of the most suitable alternatives to hard chromium mainly owing to their remarkable mechanical and tribological properties. Additionally, advanced technologies that require materials resistant to high temperatures could benefit from the use of Ni-W coatings. In this work, the effect of thermal treatment at different temperatures (300, 500, 700°C) on the characteristics of Ni-W coatings obtained by direct and pulse plating (PP) was studied. The morphology, composition, crystalline structure, hardness, wear rate, friction coefficient and corrosion resistance of the thermally treated coatings were analysed and compared with the performance of hard chromium coatings. The results indicate that the pulse-plated Ni-W coatings show better mechanical and tribological properties than the ones obtained by direct current. A significant improvement in hardness in Ni-W layers was achieved by thermal treatment, mainly in the films grown by PP, with minor changes in wear resistance and corrosion performance.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Multiwavelength light-responsive Au/B-TiO2 Janus micromotors

  • Jang, Bumjin
  • Hong, Ayoung
  • KangHa, Eun Kang
  • Alcantara, Carlos
  • Charreyron, Samuel
  • Mushtaq, Fajer
  • Pellicer, Eva|||0000-0002-8901-0998
  • Büchel, Robert
  • Sort, Jordi|||0000-0003-1213-3639
  • Lee, Sung Sik
  • Nelson, Bradley J.|||0000-0001-9070-6987
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
Conventional photocatalytic micromotors are limited to the use of specific wavelengths of light due to their narrow light absorption spectrum, which limits their effectiveness for applications in biomedicine and environmental remediation. We present a multiwavelength light-responsive Janus micromotor consisting of a black TiO₂ microsphere asymmetrically coated with a thin Au layer. The black TiO₂ microspheres exhibit absorption ranges between 300 and 800 nm. The Janus micromotors are propelled by light, both in H₂O₂ solutions and in pure H₂O over a broad range of wavelengths including UV, blue, cyan, green, and red light. An analysis of the particles' motion shows that the motor speed decreases with increasing wavelength, which has not been previously realized. A significant increase in motor speed is observed when exploiting the entire visible light spectrum (.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Enhanced mechanical properties and microstructural modifications in electrodeposited Fe-W alloys through controlled heat treatments

  • Mulone, Antonio
  • Nicolenco, Aliona|||0000-0003-4624-2163
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Pellicer, Eva|||0000-0002-8901-0998
  • Tsyntsaru, N.
  • Cesiulis, Henrikas|||0000-0002-5077-7884
  • Sort, Jordi|||0000-0003-1213-3639
  • Klement, U.
Among W alloys, Fe-W has seen much attention recently, due to the need of moving toward the design of environmentally friendly materials. Coatings with 4, 16 and 24 at.% of W were electrodeposited from an environmental friendly Fe(III)-based glycolate-citrate bath. The samples were annealed in vacuum at different temperatures up to 800 °C. Different crystalline phases are formed upon annealing: α-Fe, Fe2W, Fe3W3C, Fe6W6C, and FeWO4. Their grain size and distribution within the coating was studied by means of Electron Backscattered Diffraction (EBSD) technique. The effect of annealing on the mechanical properties of the coatings was analyzed performing nanoindentation measurements. The results show a considerable increase of the hardness followed by a rapid decrease at higher temperatures. The highest hardness value, i.e. 16.5 GPa, is measured for the sample with 24 at.% of W after annealing at 600 °C owing to the precipitation of α-Fe crystallites. This study indicates the possibility to substantially increase the hardness of electrodeposited Fe-W coatings by optimization of the annealing treatment. In addition, the critical influence of the carbide and oxide phases on the mechanical properties of alloys is discussed. Hence, Fe-W coatings rich in W can be applied as a possible candidate for protective coating applications at elevated temperatures.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrodeposition of amorphous Fe-Cr-Ni stainless steel alloy with high corrosion resistance, low cytotoxicity and soft magnetic properties

  • Bertero, Enrico|||0000-0001-6952-8741
  • Hasegawa, Madoka
  • Staubli, Samuel
  • Pellicer, Eva|||0000-0002-8901-0998
  • Herrmann, Inge K.
  • Sort, Jordi|||0000-0003-1213-3639
  • Michler, Johann|||0000-0001-8860-4068
  • Philippe, Laetitia|||0000-0003-0928-4487
Electrodeposition of Fe-Cr-Ni alloy thin films with high corrosion resistance, low cytotoxicity and soft-magnetic properties is reported. Fe-Cr-Ni films with Cr contents from 5 wt% to 40 wt% were prepared by adjusting the current density during electrodeposition and the film properties were investigated. An excellent corrosion resistance was found in films with high Cr contents (≥30 wt%), where anodic polarization performance similar to those of AISI 304 and 316L stainless steels was observed in both acidic and biological media. Cell compatibility, measured by lactate dehydrogenase assay, demonstrated that electrodeposited Fe-Cr-Ni films exhibit low cytotoxicity, comparable to AISI 304 and 316L stainless steels. Unlike AISI 304 and AISI 316L, which are conventional austenite stainless steels, the electrodeposited Fe-Cr-Ni films were found to be amorphous. This leads to soft ferromagnetic characteristics, which are dependent on the alloy composition. The unique combination of excellent corrosion resistance, low cytotoxicity and tunable magnetic properties makes this material interesting for functional coatings and components in advanced biological and medical microsystems.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

New binuclear copper(ii) coordination polymer based on mixed pyrazolic and oxalate ligands, Structural characterization and mechanical properties

  • López Marzo, Adaris María|||0000-0001-8552-8637
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Calvet, Teresa|||0000-0002-4058-7171
  • Font-Bardia, Mercè|||0000-0002-7892-8744
  • Pellicer, Eva|||0000-0002-8901-0998
  • Baró, M. D.|||0000-0002-8636-1063
  • Pons Picart, Josefina|||0000-0003-1834-9326
  • Sort, Jordi|||0000-0003-1213-3639
A new inorganic-organic coordination polymer based on a copper(ii) binuclear complex coordinated with pyrazole (L1), 1-(hydroxymethyl)pyrazole) (L2) and oxalate (Ox) ligands has been unexpectedly obtained. The crystal structure of this coordination polymer has been unequivocally determined from single crystal X-ray diffraction. One copper(ii) center (Cu1) is four-coordinated with two nitrogens (N2, L1 and N3, L2), one oxygen (O1, L1) and one chlorine atom, while the other copper(ii) nucleus (Cu2) is five-coordinated with one nitrogen (N1, L1), three oxygens (O1, L2; O2 and O3, Ox) and one chlorine atom, giving slightly distorted square-planar and square-pyramidal geometries, respectively. To the best of our knowledge, such coordination environments have never been previously observed to coexist in the same structure. The terminal chlorine (Cl1) forms the connecting bridge between the planar binuclear [CuCl(Ox)(L1)(L2)] units ending in an attractive structural framework. An extended layered structure staggered along the b-axis is observed in the supramolecular view. Nanoindentation experiments were carried out and relevant mechanical parameters such as hardness, Young's modulus, indentation energies and elastic recovery were determined. Additionally, a comparative analysis between the supramolecular structure and the mechanical properties is reported.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Coercivity Modulation in Fe-Cu Pseudo-Ordered Porous Thin Films Controlled by an Applied Voltage, A Sustainable, Energy-Efficient Approach to Magnetoelectrically Driven Materials

  • Dislaki, Evangelia|||0000-0002-3360-1588
  • Robbennolt, Shauna|||0000-0001-5723-7971
  • Campoy-Quiles, Mariano|||0000-0002-8911-640X
  • Nogués, Josep|||0000-0003-4616-1371
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Fe-Cu films with pseudo-ordered, hierarchical porosity are prepared by a simple, two-step procedure that combines colloidal templating (using sub-micrometer-sized polystyrene spheres) with electrodeposition. The porosity degree of these films, estimated by ellipsometry measurements, is as high as 65%. The resulting magnetic properties can be controlled at room temperature using an applied electric field generated through an electric double layer in an anhydrous electrolyte. This material shows a remarkable 25% voltage-driven coercivity reduction upon application of negative voltages, with excellent reversibility when a positive voltage is applied, and a short recovery time. The pronounced reduction of coercivity is mainly ascribed to electrostatic charge accumulation at the surface of the porous alloy, which occurs over a large fraction of the electrodeposited material due to its high surface-area-to-volume ratio. The emergence of a hierarchical porosity is found to be crucial because it promotes the infiltration of the electrolyte into the structure of the film. The observed effects make this material a promising candidate to boost energy efficiency in magnetoelectrically actuated devices.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Large magnetoelectric effects in electrodeposited nanoporous microdisks driven by effective surface charging and magneto-ionics

  • Navarro Senent, Cristina Maria|||0000-0002-7757-0357
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Isarain-Chávez, Eloy|||0000-0002-4154-1343
  • Quintana, Alberto|||0000-0002-9813-735X
  • Menéndez, Enric|||0000-0003-3809-2863
  • Foerster, Michael|||0000-0002-4147-6668
  • Aballe, Lucía|||0000-0003-1810-8768
  • Weschke, Eugen
  • Nogués, Josep|||0000-0003-4616-1371
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
A synergetic approach to enhance magnetoelectric effects (i.e., control of magnetism with voltage) and improve energy efficiency in magnetically actuated devices is presented. The investigated material consists of an ordered array of Co-Pt microdisks, in which nanoporosity and partial oxidation are introduced during the synthetic procedure to synergetically boost the effects of electric field. The microdisks are grown by electrodeposition from an electrolyte containing an amphiphilic polymeric surfactant. The bath formulation is designed to favor the incorporation of oxygen in the form of cobalt oxide. A pronounced reduction of coercivity (88%) and a remarkable increase of Kerr signal amplitude (60%) are observed at room temperature upon subjecting the microdisks to negative voltages through an electrical double layer. These large voltage-induced changes in the magnetic properties of the microdisks are due to (i) the high surface-area-to-volume ratio with ultranarrow pore walls (sub-10 nm) that promote enhanced electric charge accumulation and (ii) magneto-ionic effects, where voltage-driven O2- migration promotes a partial reduction of CoO to Co at room temperature. This simple and versatile procedure to fabricate patterned "nano-in-micro" magnetic motifs with adjustable voltage-driven magnetic properties is very appealing for energy-efficient magnetic recording systems and other magnetoelectronic devices.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Voltage-controlled ON-OFF ferromagnetism at room temperature in a single metal oxide film

  • Quintana, Alberto|||0000-0002-9813-735X
  • Menéndez, Enric|||0000-0003-3809-2863
  • Liedke, Maciej O.
  • Butterling, Maik|||0000-0003-3674-0767
  • Wagner, Andreas|||0000-0001-7575-3961
  • Sireus, Verònica
  • Torruella, Pau
  • Estrade, Sonia|||0000-0002-3340-877X
  • Peiro, Francesca|||0000-0002-5697-0554
  • Dendooven, Jolien
  • Detavernier, Christophe
  • Murray, Peyton D.|||0000-0003-0389-0611
  • Allen Gilbert, Dustin
  • Liu, Kai|||0000-0001-9413-6782
  • Pellicer, Eva|||0000-0002-8901-0998
  • Nogués, Josep|||0000-0003-4616-1371
  • Sort, Jordi|||0000-0003-1213-3639
Electric-field-controlled magnetism can boost energy efficiency in widespread applications. However, technologically, this effect is facing important challenges: mechanical failure in strain-mediated piezoelectric/magnetostrictive devices, dearth of room-temperature multiferroics, or stringent thickness limitations in electrically charged metallic films. Voltage-driven ionic motion (magneto-ionics) circumvents most of these drawbacks while exhibiting interesting magnetoelectric phenomena. Nevertheless, magneto-ionics typically requires heat treatments and multicomponent heterostructures. Here we report on the electrolyte-gated and defect-mediated O and Co transport in a Co₃O₄ single layer which allows for room-temperature voltage-controlled ON-OFF ferromagnetism (magnetic switch) via internal reduction/oxidation processes. Negative voltages partially reduce Co₃O₄ to Co (ferromagnetism: ON), resulting in graded films including Co- and O-rich areas. Positive bias oxidizes Co back to Co₃O₄ (paramagnetism: OFF). This electric-field-induced atomic-scale reconfiguration process is compositionally, structurally, and magnetically reversible and self-sustained, since no oxygen source other than the Co₃O₄ itself is required. This process could lead to electric-field-controlled device concepts for spintronics.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Epitaxial versus polycrystalline shape memory Cu-Al-Ni thin films

  • Bilican, Doğa|||0000-0002-9497-5065
  • Kurdi, Samer|||0000-0002-7374-2844
  • Zhu, Yi
  • Solsona, Pau|||0000-0001-9274-2447
  • Pellicer, Eva|||0000-0002-8901-0998
  • Barber, Zoe H.
  • Greer, Alan Lindsay
  • Sort, Jordi|||0000-0003-1213-3639
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
In this work, two different approaches were followed to obtain Cu-Al-Ni thin films with shape memory potential. On the one hand, Cu-Ni/Al multilayers were grown by magnetron sputtering at room temperature. To promote diffusion and martensitic/austenitic phase transformation, the multilayers were subjected to subsequent heat treatment at 800 °C and quenched in iced water. On the other hand, Cu, Al, and Ni were co-sputtered onto heated MgO (001) substrates held at 700 °C. Energy-dispersive X-ray spectroscopy, X-ray diffraction, and transmission electron microscopy analyses were carried out to study the resulting microstructures. In the former method, with the aim of tuning the thin film's composition, and, consequently, the martensitic transformation temperature, the sputtering time and applied power were adjusted. Accordingly, martensitic Cu-14Al-4Ni (wt.%) and Cu-13Al-5Ni (wt.%) thin films and austenitic Cu-12Al-7Ni (wt.%) thin films were obtained. In the latter, in situ heating during film growth led to austenitic Cu-12Al-7Ni (wt.%) thin films with a (200) textured growth as a result of the epitaxial relationship MgO(001)[100]/Cu-Al-Ni(001)[110]. Resistance versus temperature measurements were carried out to investigate the shape memory behavior of the austenitic Cu-12Al-7Ni (wt.%) thin films produced from the two approaches. While no signs of martensitic transformation were detected in the quenched multilayered thin films, a trend that might be indicative of thermal hysteresis was encountered for the epitaxially grown thin films. In the present work, the differences in the crystallographic structure and the shape memory behavior of the Cu-Al-Ni thin films obtained by the two different preparation approaches are discussed.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrodeposition of nanocrystalline Fe-P coatings, influence of bath temperature and glycine concentration on structure, mechanical and corrosion behavior

  • Kovalska, Natalia
  • Tsyntsaru, Natalia|||0000-0002-9813-2460
  • Cesiulis, Henrikas|||0000-0002-5077-7884
  • Gebert, Annet
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
  • Hansal, Wolfgang
  • Kautek, Wolfgang|||0000-0003-2772-2049
A detailed electrochemical study and investigation of a Fe-P glycine bath as a function of the temperature and glycine concentrations and current density, and their resulting corrosion and mechanical behavior is presented. A low addition of glycine to the electrolyte led to a drastic increase of the P content. At low Fe-P deposition rates, heterogeneous rough deposits with morphological bumps and pores were observed. By increasing the Fe-P deposition rate, the number of pores were reduced drastically, resulting in smooth coatings. Increasing the P content led to the formation of nanocrystalline grains from an "amorphous-like" state. Coatings with higher P contents exhibited better corrosion resistance and hardening, most likely attributed to grain boundary strengthening.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Functional macroporous iron-phosphorous films by electrodeposition on colloidal crystal templates

  • Golvano Escobal, Irati|||0000-0001-8518-8185
  • de Paz Castany, Roger|||0000-0003-4211-2636
  • Alcantara, Carlos
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • García-Lecina, Eva|||0000-0001-8915-840X
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Pseudo-ordered macroporous iron-phosphorous (Fe-P) films have been electrodeposited potentiostatically from a citrate-sulfate bath onto Au surfaces pre-patterned with a colloidal crystal mask of polystyrene spheres of 350 nm in diameter. The electrolyte contained sodium hypophosphite as the P source, enabling the incorporation of 6-14 at.% P. For comparative purposes, continuous films have been obtained galvanostatically on unpatterned Au surfaces. In both cases, the P content could be varied to a certain extent by adjusting the deposition potential or current density. Tunable microstructure and magnetic response was observed due to the dissimilar chemical composition, with coercivity values being larger in the macroporous films. Additionally, wettability analyses showed that these were more hydrophobic, reaching contact angle values of about 130∘. In spite of their hydrophobic character, the samples were catalytic toward oxygen evolution reaction (OER) in alkaline media. The macroporous Fe-P films showed faster kinetics for OER than their nonporous counterparts. Our results show that electrodeposited porous Fe-P based materials show an interesting combination of properties which make them appealing for applications including water cleaning, soft-magnetic components, or electrocatalytic production of oxygen, to name a few.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

'Green' Cr(III)-glycine electrolyte for the production of FeCrNi coatings, Electrodeposition mechanisms and role of by-products in terms of coating composition and microstructure

  • Bertero, Enrico|||0000-0001-6952-8741
  • Manzano, Cristina V.|||0000-0001-5708-6544
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
  • Ulfig, Robert M.
  • Mischler, Stefano
  • Michler, Johann|||0000-0001-8860-4068
  • Philippe, Laetitia|||0000-0003-0928-4487
The electrodeposition of stainless steel-like FeCrNi alloys for miniaturised devices is appealing as it would allow combining excellent material properties (e.g. corrosion resistance, hardness, biocompatibility) at low-cost. However, conventional baths often contain hazardous hexavalent chromium. Cr-based alloys electrodeposited from environmentally friendly trivalent chromium electrolytes are crucial for industrial application for facilitating the transition towards sustainable and ecological production and processing. Nevertheless, this process has not been comprehensively studied or understood in depth: Especially the role of organic agents (common additives for improving Cr(iii)-based plating; e.g. glycine) in terms of material properties of the electrodeposits. The aim of this work was to investigate the electrodeposition of FeCrNi coatings from a 'green' Cr(iii)-glycine electrolyte. Novel information was attained by analysing films developed under various conditions and characterising them using a combination of advanced techniques. The evolution of microstructure (from amorphous to nanocrystalline) in correlation with film composition (i.e. metals ratio and presence of impurities) and elemental 3D spatial distribution was achieved for coatings produced from different anode materials and thermal post-treatment. The influence of Cr(iii) and glycine in terms of coating atomic contents (i.e. Fe-Cr-Ni-O-C-N-H) was evaluated for films in which both the applied current density and electrolyte composition were varied. These results, together with a thorough analysis on metals speciation/complexation allowed us to propose various Cr(iii)-based electroreduction mechanisms, and to observe, upon annealing, segregation and distribution of impurities, as well as of oxides and metals with respect to microstructure variation, providing an explanation for the amorphisation process.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Large magnetoelectric effects mediated by electric-field-driven nanoscale phase transformations in sputtered (nanoparticulate) and electrochemically dealloyed (nanoporous) Fe-Cu films

  • Robbennolt, Shauna|||0000-0001-5723-7971
  • Quintana, Alberto|||0000-0002-9813-735X
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Large magnetoelectric effects are observed in as-sputtered (nanoparticulate-like) and electrochemically dealloyed (nanoporous) 200 nm thick Fe-Cu films. Large magnetoelectric effects are observed in as-sputtered (nanoparticulate-like) and electrochemically dealloyed (nanoporous) 200 nm thick Fe-Cu films. Application of positive voltages decreases both the saturation magnetization (M ) and coercivity (H ) of the films, while negative voltages cause the reverse effect (increase of M and H ). The relative variations are as high as 20% for M and beyond 100% for H , both for the as-sputtered and dealloyed states. These changes in magnetic properties are caused by controlled and reversible electric-field-driven nanoscale phase transformations between face-centered cubic (fcc) and body-centered cubic (bcc) structures. These phase transitions are in turn due to selective redox reactions induced by the applied voltage, which can be regarded as a "magnetoionic effect." The controlled tuning of H and M with the moderate values of applied voltage, together with the sustainable composition of the investigated alloys (not containing noble metals, as opposed to many previous works on magnetoelectric effects in thin films), pave the way towards the implementation of magnetic and spintronic devices with enhanced energy efficiency and functionalities.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrolyte-gated magnetoelectric actuation, Phenomenology, materials, mechanisms, and prospective applications

  • Navarro Senent, Cristina Maria|||0000-0002-7757-0357
  • Quintana, Alberto|||0000-0002-9813-735X
  • Menéndez, Enric|||0000-0003-3809-2863
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Manipulation of the magnetic behavior of materials with voltage (i.e., magnetoelectric actuation) has become a topic of intense research during the last years. Apart from its obvious interest from a basic science standpoint, control and eventual switching of the magnetization without applying any external magnetic field (or spin polarized current) has the potential to drastically reduce the power consumption of magnetic devices due to the lack (or minimization) of Joule heating dissipation effects. Herein, an overview of the state-of-the-art of electrolyte-gated magnetoelectric actuation (where an electric field is applied using an electrolyte, either liquid or solid) is provided. The different types of mechanisms responsible for voltage-driven magnetic actuation (surface charging, ionic migration, also termed "magneto-ionics," reduction/oxidation reactions, and ferroelectric/ferromagnetic coupling) are summarized. The various effects (changes in coercivity, anisotropy easy axis, exchange bias field, saturation magnetization, Curie temperature, etc.) observed in the different types of materials investigated so far (mainly metallic thin films and semiconductors, porous alloys, and nanocomposite structures) are described. The potential applications of electrolyte-gated magnetoelectric actuation in devices as well as the current challenges in the field are also reviewed with the aim of providing the basic ingredients for further prospects and technological advancements in this area.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Reversible, electric-field induced magneto-tonic control of magnetism in mesoporous cobalt ferrite thin films

  • Robbennolt, Shauna|||0000-0001-5723-7971
  • Menéndez, Enric|||0000-0003-3809-2863
  • Quintana, Alberto|||0000-0002-9813-735X
  • Gómez, Andrés|||0000-0003-2847-0138
  • Auffret, Stéphane
  • Baltz, Vincent
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
The magnetic properties of mesoporous cobalt ferrite films can be largely tuned by the application of an electric field using a liquid dielectric electrolyte. By applying a negative voltage, the cobalt ferrite becomes reduced, leading to an increase in saturation magnetization of 15% (M) and reduction in coercivity (H) between 5-28%, depending on the voltage applied (-10 V to -50 V). These changes are mainly non-volatile so after removal of -10 V M remains 12% higher (and H 5% smaller) than the pristine sample. All changes can then be reversed with a positive voltage to recover the initial properties even after the application of -50 V. Similar studies were done on analogous films without induced porosity and the effects were much smaller, underscoring the importance of nanoporosity in our system. The different mechanisms possibly responsible for the observed effects are discussed and we conclude that our observations are compatible with voltage-driven oxygen migration (i.e., the magneto-ionic effect).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Piezoelectrically enhanced photocatalysis with BiFeO3 nanostructures for efficient water remediation

  • Mushtaq, Fajer
  • Chen, Xiangzhong|||0000-0002-2294-7487
  • Hoop, Marcus
  • Torlakcik, Harun
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
  • Gattinoni, Chiara
  • Nelson, Bradley J.|||0000-0001-9070-6987
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
Designing new catalysts that can efficiently utilize multiple energy sources can contribute to solving the current challenges of environmental remediation and increasing energy demands. In this work, we fabricated single-crystalline BiFeO3 (BFO) nanosheets and nanowires that can successfully harness visible light and mechanical vibrations and utilize them for degradation of organic pollutants. Under visible light both BFO nanostructures displayed a relatively slow reaction rate. However, under piezocatalysis both nanosheets and nanowires exhibited higher reaction rates in comparison with photocatalytic degradation. When both solar light and mechanical vibrations were used simultaneously, the reaction rates were elevated even further, with the BFO nanowires degrading 97% of RhB dye within 1 hr (k-value 0.058 min-1). The enhanced degradation under mechanical vibrations can be attributed to the promotion of charge separation caused by the internal piezoelectric field of BFO. BFO nanowires also exhibited good reusability and versatility toward degrading four different organic pollutants.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Synthesis of α-Fe2O3 and Fe-Mn oxide foams with highly tunable magnetic properties by the replication method from polyurethane templates

  • Feng, Yuping
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Zhang, Huiyan
  • Solsona, Pau|||0000-0001-9274-2447
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Open cell foams consisting of Fe and Fe-Mn oxides are prepared from metallic Fe and Mn powder precursors by the replication method using porous polyurethane (PU) templates. First, reticulated PU templates are coated by slurry impregnation. The templates are then thermally removed at 260 °C and the debinded powders are sintered at 1000 °C under N2 atmosphere. The morphology, structure, and magnetic properties are studied by scanning electron microscopy, X-ray diffraction and vibrating sample magnetometry, respectively. The obtained Fe and Fe-Mn oxide foams possess both high surface area and homogeneous open-cell structure. Hematite (α-Fe2O3) foams are obtained from the metallic iron slurry independently of the N2 flow. In contrast, the microstructure of the FeMn-based oxide foams can be tailored by adjusting the N2 flow. While the main phases for a N2 flow rate of 180 L/h are α-Fe2O3 and FeMnO3, the predominant phase for high N2 flow rates (e.g., 650 L/h) is Fe2MnO4. Accordingly, a linear magnetization versus field behavior is observed for the hematite foams, while clear hysteresis loops are obtained for the Fe2MnO4 foams. Actually, the saturation magnetization of the foams containing Mn increases from 5 emu/g to 52 emu/g when the N2 flow rate (i.e., the amount of Fe2MnO4) is increased. The obtained foams are appealing for a wide range of applications, such as electromagnetic absorbers, catalysts supports, thermal and acoustic insulation systems or wirelessly magnetically-guided porous objects in fluids.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Structural and magnetic properties of FexCu1-x sputtered thin films electrochemically treated to create nanoporosity for high-surface-area magnetic components

  • Robbennolt, Shauna|||0000-0001-5723-7971
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Quintana, Alberto|||0000-0002-9813-735X
  • Zhang, Huiyan
  • Menéndez, Enric|||0000-0003-3809-2863
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Sputter deposition is a facile and widely used technique for fabricating thin-film materials. Electrochemical dealloying, on the other hand, is a promising method for creating nanoporosity, and therefore increasing surface area, in metallic materials. Surprisingly, little work has been done on the application of electrochemical dealloying to sputter-deposited thin films. Here, we prepare FexCu1-x thin films by sputter deposition to be then electrochemically treated to create porosity. We investigate the structural and magnetic properties of as-sputtered and electrochemically treated films. We find that the morphology, crystal structure, and magnetic properties are highly dependent on initial film composition. For high copper content films (Fe29Cu71), relative Cu content is found to decrease during the dealloying process. For these films, the crystal structure is not greatly affected by the induced porosity and the porous films show increased saturation magnetization. However, for the more Fe-rich compositions (Fe63Cu37), we find that Fe is preferentially lost and making the films nanoporous induces a crystal structure change from body-centered cubic (bcc) to a mixture of face-centered cubic (fcc) and bccphases. These same porous films show a decrease in saturation magnetization and a large increase in coercivity compared to the as-sputtered films. These films are attractive as high-surface-area magnetic components because of the tunability of their magnetic properties and their high surface area due to porosity. To the best of our knowledge, these results constitute the first example of nanoporous, magnetic thin films by prepared by sputtering and subsequent electrochemical treatment.