Pasar al contenido principal

-

IJCI-2015-27030

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Incorporación
Convocatoria Juan de la Cierva Incorporación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSIDAD AUTONOMA DE BARCELONA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Large magnetoelectric effects in electrodeposited nanoporous microdisks driven by effective surface charging and magneto-ionics

  • Navarro-Senent, Cristina
  • Fornell, Jordina
  • Isarain-Chávez, Eloy
  • Quintana, Alberto
  • Menéndez, Enric
  • Foerster, Michael
  • Aballe, Lucía
  • Weschke, Eugen
  • Nogués, Josep
  • Pellicer, Eva
  • Sort, Jordi
A synergetic approach to enhance magnetoelectric effects (i.e., control of magnetism with voltage) and improve energy efficiency in magnetically actuated devices is presented. The investigated material consists of an ordered array of Co–Pt microdisks, in which nanoporosity and partial oxidation are introduced during the synthetic procedure to synergetically boost the effects of electric field. The microdisks are grown by electrodeposition from an electrolyte containing an amphiphilic polymeric surfactant. The bath formulation is designed to favor the incorporation of oxygen in the form of cobalt oxide. A pronounced reduction of coercivity (88%) and a remarkable increase of Kerr signal amplitude (60%) are observed at room temperature upon subjecting the microdisks to negative voltages through an electrical double layer. These large voltage-induced changes in the magnetic properties of the microdisks are due to (i) the high surface-area-to-volume ratio with ultranarrow pore walls (sub-10 nm) that promote enhanced electric charge accumulation and (ii) magneto-ionic effects, where voltage-driven O2– migration promotes a partial reduction of CoO to Co at room temperature. This simple and versatile procedure to fabricate patterned “nano-in-micro” magnetic motifs with adjustable voltage-driven magnetic properties is very appealing for energy-efficient magnetic recording systems and other magnetoelectronic devices., This work was funded by the European Research Council under the SPIN-PORICS 2014-Consolidator Grant (Agreement No. 648454), the Generalitat de Catalunya (2017-SGR292 project), the Spanish Government (MAT2017-86357-C3-1-R, MAT2014-57960-C3-1-R, and associated FEDER projects), and the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No. 665919. J.F. and E.P. acknowledge the Juan de la Cierva (IJCI-2015-27030) and Ramon y Cajal (RYC-2012-10839) fellowships, respectively, from MINECO. The ICN2 is funded by the CERCA program/Generalitat de Catalunya. ICN2 also acknowledges the support from the Severo Ochoa Program (MINECO, grant SEV-2013-0295), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tunable magnetism in nanoporous CuNi alloys by reversible voltage‐driven element‐selective redox processes

  • Quintana, Alberto
  • Menéndez, Enric
  • Isarain-Chávez, Eloy
  • Fornell, Jordina
  • Solsona, Pau
  • Fauth, François
  • Baró, María Dolors
  • Nogués, Josep
  • Pellicer, Eva
  • Sort, Jordi
Voltage-driven manipulation of magnetism in electrodeposited 200 nm thick nanoporous single-phase solid solution Cu20 Ni80 (at%) alloy films (with sub 10 nm pore size) is accomplished by controlled reduction-oxidation (i.e., redox) processes in a protic solvent, namely 1 m NaOH aqueous solution. Owing to the selectivity of the electrochemical processes, the oxidation of the CuNi film mainly occurs on the Cu counterpart of the solid solution, resulting in a Ni-enriched alloy. As a consequence, the magnetic moment at saturation significantly increases (up to 33% enhancement with respect to the as-prepared sample), while only slight changes in coercivity are observed. Conversely, the reduction process brings Cu back to its metallic state and, remarkably, it becomes alloyed to Ni again. The reported phenomenon is fully reversible, thus allowing for the precise adjustment of the magnetic properties of this system through the sign and amplitude of the applied voltage., The financial support by the European Research Council (SPINPORICS 2014-Consolidator Grant, Agreement No. 648454), the Spanish Government (Projects MAT2017-86357-C3-1-R, MAT2014-57960-C3-1-R and associated FEDER), the Generalitat de Catalunya (2017-SGR-292), and the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement no. 665919 is acknowledged. E.P. is grateful to MINECO for the “Ramón y Cajal” contract (RYC-2012-10839). The authors are also indebted to the National Council on Science and Technology in Mexico (CONACYT) for the postdoctoral grant (274347) given to E.I.-C. J.F. acknowledges the Juan de la Cierva Fellowship from MINECO (Grant no. IJCI-2015-27030). The ICN2 is funded by the CERCA programme/Generalitat de Catalunya. ICN2 also acknowledges the support from the Severo Ochoa Program (MINECO, Grant no. SEV-2013-0295)., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Biodegradable FeMnSi sputter-coated macroporous polypropylene membranes for the sustained release of drugs

  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Soriano Martín, Jorge|||0000-0003-3295-7643
  • Guerrero, Miguel|||0000-0001-8350-8261
  • Sirvent, Juan de Dios
  • Ferran, Marta|||0000-0003-1198-0641
  • Ibáñez, Elena|||0000-0002-0275-6958
  • Barrios, Leonardo|||0000-0002-6151-8503
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Nogués, Carme|||0000-0002-6361-8559
  • Sort, Jordi|||0000-0003-1213-3639
  • Pellicer, Eva|||0000-0002-8901-0998
Pure Fe and FeMnSi thin films were sputtered on macroporous polypropylene (PP) membranes with the aim to obtain biocompatible, biodegradable and, eventually, magnetically-steerable platforms. Room-temperature ferromagnetic response was observed in both Fe- and FeMnSi-coated membranes. Good cell viability was observed in both cases by means of cytotoxicity studies, though the FeMnSi-coated membranes showed higher biodegradability than the Fe-coated ones. Various strategies to functionalize the porous platforms with transferrin-Alexa Fluor 488 (Tf-AF488) molecules were tested to determine an optimal balance between the functionalization yield and the cargo release. The distribution of Tf-AF488 within the FeMnSi-coated PP membranes, as well as its release and uptake by cells, was studied by confocal laser scanning microscopy. A homogeneous distribution of the drug within the membrane skeleton and its sustained release was achieved after three consecutive impregnations followed by the addition of a layer made of gelatin and maltodextrin, which prevented exceedingly fast release. The here-prepared organic-inorganic macroporous membranes could find applications as fixed or magnetically-steerable drug delivery platforms.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Mechanical properties, corrosion performance and cell viability studies on newly developed porous Fe-Mn-Si-Pd alloys

  • Feng, Yuping
  • Gaztelumendi, Nerea|||0000-0002-3837-2956
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Zhang, Huiyan
  • Solsona, Pau|||0000-0001-9274-2447
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Ibáñez, Elena|||0000-0002-0275-6958
  • Barrios, Leonardo|||0000-0002-6151-8503
  • Pellicer, Eva|||0000-0002-8901-0998
  • Nogués, Carme|||0000-0002-6361-8559
  • Sort, Jordi|||0000-0003-1213-3639
Porous Fe-30Mn6Si1Pd (wt.%) alloys were prepared by a simple press and sinter process from ball-milled Fe, Mn, Si and Pd powders blended with 10 wt%, 20 wt% and 40 wt% NaCl to obtain different degrees of porosity. For comparison purposes, a bulk fully-compact Fe-30Mn6Si1Pd alloy was produced by arc-melting and subsequent copper-mold suction-casting. While the porous Fe-30Mn6Si1Pd alloys only consist of γ-austenite, their fully-compact counterpart comprises ε-martensite and γ-austenite phases. In all cases, the low magnetic susceptibility response assures good compatibility with nuclear magnetic resonance and magnetic resonance imaging techniques. Furthermore, a reduction of the Young's modulus, from 55 to 7 GPa, was attained by introducing porosity. The biodegradation performance was evaluated by static immersion and electrochemical corrosion tests in Hank's solution. The influence of immersion time on composition, microstructure, mechanical and magnetic properties was assessed. While introducing porosity renders alloys with suitable mechanical and magnetic properties, it also has a detrimental effect in terms of cell viability. Hence, the porosity level needs to be controlled in order to obtain alloys with an optimized performance.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Mechanical behaviour of brushite and hydroxyapatite coatings electrodeposited on newly developed FeMnSiPd alloys

  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Feng, Yuping
  • Pellicer, Eva|||0000-0002-8901-0998
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Sort, Jordi|||0000-0003-1213-3639
Calcium phosphate coatings (CaP) (i.e., brushite and hydroxyapatite) were grown by pulsed current electrodeposition on FeMnSiPd alloys, a newly developed material proposed for biomedical implants. The electrolytic baths contained Ca(NO₃)₂·4H₂O and NH₄H₂PO₄ as precursors. Bath additives, such as H₂O₂ and NaOH, were used to promote hydroxyapatite (HAp) coating formation directly from the bath. The effect of the electrodeposition parameters on the structure, morphology and mechanical performance of the coatings was investigated. Increasing the electrodeposition time from 900s to 3600s resulted in an increase of HAp over the dominant brushite structure. Addition of 2000 ppm of NaOH or 3000 ppm of H₂O₂ also promoted an increase of HAp fraction when compared to the coatings obtained from the additive-free bath. Nonetheless, pure HAp was only achieved with the addition of 4000 ppm of NaOH to the electrolyte. The morphologies of the CaP particles in the coatings ranged from needle- to plate-like structures depending on the electrodeposition parameters and the resulting phases. The mechanical behaviour of the coatings was studied by scratch testing and nanoindentation. As a general trend, the Young's modulus and hardness values of the electrodeposited coatings were lower than those reported for fully-dense HAp, independently of the deposition conditions, because of the porous morphology of the coatings. No signs of cracking or delamination were observed during nanoindentation or scratch tests except for the coating prepared form the electrolyte containing 3000 ppm of H₂O₂.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Ferromagnetic-like behaviour in bismuth ferrite films prepared by electrodeposition and subsequent heat treatment

  • Bilican, Doğa|||0000-0002-9497-5065
  • Menéndez, Enric|||0000-0003-3809-2863
  • Solsona, Pau|||0000-0001-9274-2447
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Bismuth ferrite (BiFeO₃) films (10 μm in thickness) are synthesized by electrodeposition from a dimethylformamide bath containing Bi and Fe nitrate salts as precursors followed by heat treatment in air. Thermal treatments are needed to induce crystallisation of the as-deposited amorphous-like films. A detailed morphological, structural and magnetic characterisation evidences that BiFeO3 forms in a rather narrow temperature window (around 600 °C). At lower and higher temperatures, secondary binary and ternary oxides are also formed. Soft ferromagnetic-like behaviour is observed in all films, which presumably arises from the obtained nanoscale structure, which favours the occurrence of spin canting in the BiFeO₃ antiferromagnetic phase. The eventual contribution from secondary phases to the observed ferromagnetic-like response is also discussed. The obtained results are appealing for the integration of BiFeO₃ into devices that may require relatively thick films with an enhanced surface area-to-volume ratio. The growth of this type of material by techniques other than electrodeposition is not straightforward.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Tunable magnetism in nanoporous CuNi alloys by reversible voltage-driven element-selective redox processes

  • Quintana, Alberto|||0000-0002-9813-735X
  • Menéndez, Enric|||0000-0003-3809-2863
  • Isarain-Chávez, Eloy|||0000-0002-4154-1343
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Solsona, Pau|||0000-0001-9274-2447
  • Baró, M. D.|||0000-0002-8636-1063
  • Nogués, Josep|||0000-0003-4616-1371
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Voltage-driven manipulation of magnetism in electrodeposited 200 nm thick nanoporous single-phase solid solution Cu20 Ni80 (at%) alloy films (with sub 10 nm pore size) is accomplished by controlled reduction-oxidation (i.e., redox) processes in a protic solvent, namely 1 m NaOH aqueous solution. Owing to the selectivity of the electrochemical processes, the oxidation of the CuNi film mainly occurs on the Cu counterpart of the solid solution, resulting in a Ni-enriched alloy. As a consequence, the magnetic moment at saturation significantly increases (up to 33% enhancement with respect to the as-prepared sample), while only slight changes in coercivity are observed. Conversely, the reduction process brings Cu back to its metallic state and, remarkably, it becomes alloyed to Ni again. The reported phenomenon is fully reversible, thus allowing for the precise adjustment of the magnetic properties of this system through the sign and amplitude of the applied voltage.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Enhanced mechanical properties and microstructural modifications in electrodeposited Fe-W alloys through controlled heat treatments

  • Mulone, Antonio
  • Nicolenco, Aliona|||0000-0003-4624-2163
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Pellicer, Eva|||0000-0002-8901-0998
  • Tsyntsaru, N.
  • Cesiulis, Henrikas|||0000-0002-5077-7884
  • Sort, Jordi|||0000-0003-1213-3639
  • Klement, U.
Among W alloys, Fe-W has seen much attention recently, due to the need of moving toward the design of environmentally friendly materials. Coatings with 4, 16 and 24 at.% of W were electrodeposited from an environmental friendly Fe(III)-based glycolate-citrate bath. The samples were annealed in vacuum at different temperatures up to 800 °C. Different crystalline phases are formed upon annealing: α-Fe, Fe2W, Fe3W3C, Fe6W6C, and FeWO4. Their grain size and distribution within the coating was studied by means of Electron Backscattered Diffraction (EBSD) technique. The effect of annealing on the mechanical properties of the coatings was analyzed performing nanoindentation measurements. The results show a considerable increase of the hardness followed by a rapid decrease at higher temperatures. The highest hardness value, i.e. 16.5 GPa, is measured for the sample with 24 at.% of W after annealing at 600 °C owing to the precipitation of α-Fe crystallites. This study indicates the possibility to substantially increase the hardness of electrodeposited Fe-W coatings by optimization of the annealing treatment. In addition, the critical influence of the carbide and oxide phases on the mechanical properties of alloys is discussed. Hence, Fe-W coatings rich in W can be applied as a possible candidate for protective coating applications at elevated temperatures.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Large magnetoelectric effects in electrodeposited nanoporous microdisks driven by effective surface charging and magneto-ionics

  • Navarro Senent, Cristina Maria|||0000-0002-7757-0357
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Isarain-Chávez, Eloy|||0000-0002-4154-1343
  • Quintana, Alberto|||0000-0002-9813-735X
  • Menéndez, Enric|||0000-0003-3809-2863
  • Foerster, Michael|||0000-0002-4147-6668
  • Aballe, Lucía|||0000-0003-1810-8768
  • Weschke, Eugen
  • Nogués, Josep|||0000-0003-4616-1371
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
A synergetic approach to enhance magnetoelectric effects (i.e., control of magnetism with voltage) and improve energy efficiency in magnetically actuated devices is presented. The investigated material consists of an ordered array of Co-Pt microdisks, in which nanoporosity and partial oxidation are introduced during the synthetic procedure to synergetically boost the effects of electric field. The microdisks are grown by electrodeposition from an electrolyte containing an amphiphilic polymeric surfactant. The bath formulation is designed to favor the incorporation of oxygen in the form of cobalt oxide. A pronounced reduction of coercivity (88%) and a remarkable increase of Kerr signal amplitude (60%) are observed at room temperature upon subjecting the microdisks to negative voltages through an electrical double layer. These large voltage-induced changes in the magnetic properties of the microdisks are due to (i) the high surface-area-to-volume ratio with ultranarrow pore walls (sub-10 nm) that promote enhanced electric charge accumulation and (ii) magneto-ionic effects, where voltage-driven O2- migration promotes a partial reduction of CoO to Co at room temperature. This simple and versatile procedure to fabricate patterned "nano-in-micro" magnetic motifs with adjustable voltage-driven magnetic properties is very appealing for energy-efficient magnetic recording systems and other magnetoelectronic devices.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Epitaxial versus polycrystalline shape memory Cu-Al-Ni thin films

  • Bilican, Doğa|||0000-0002-9497-5065
  • Kurdi, Samer|||0000-0002-7374-2844
  • Zhu, Yi
  • Solsona, Pau|||0000-0001-9274-2447
  • Pellicer, Eva|||0000-0002-8901-0998
  • Barber, Zoe H.
  • Greer, Alan Lindsay
  • Sort, Jordi|||0000-0003-1213-3639
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
In this work, two different approaches were followed to obtain Cu-Al-Ni thin films with shape memory potential. On the one hand, Cu-Ni/Al multilayers were grown by magnetron sputtering at room temperature. To promote diffusion and martensitic/austenitic phase transformation, the multilayers were subjected to subsequent heat treatment at 800 °C and quenched in iced water. On the other hand, Cu, Al, and Ni were co-sputtered onto heated MgO (001) substrates held at 700 °C. Energy-dispersive X-ray spectroscopy, X-ray diffraction, and transmission electron microscopy analyses were carried out to study the resulting microstructures. In the former method, with the aim of tuning the thin film's composition, and, consequently, the martensitic transformation temperature, the sputtering time and applied power were adjusted. Accordingly, martensitic Cu-14Al-4Ni (wt.%) and Cu-13Al-5Ni (wt.%) thin films and austenitic Cu-12Al-7Ni (wt.%) thin films were obtained. In the latter, in situ heating during film growth led to austenitic Cu-12Al-7Ni (wt.%) thin films with a (200) textured growth as a result of the epitaxial relationship MgO(001)[100]/Cu-Al-Ni(001)[110]. Resistance versus temperature measurements were carried out to investigate the shape memory behavior of the austenitic Cu-12Al-7Ni (wt.%) thin films produced from the two approaches. While no signs of martensitic transformation were detected in the quenched multilayered thin films, a trend that might be indicative of thermal hysteresis was encountered for the epitaxially grown thin films. In the present work, the differences in the crystallographic structure and the shape memory behavior of the Cu-Al-Ni thin films obtained by the two different preparation approaches are discussed.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Electrodeposition of nanocrystalline Fe-P coatings, influence of bath temperature and glycine concentration on structure, mechanical and corrosion behavior

  • Kovalska, Natalia
  • Tsyntsaru, Natalia|||0000-0002-9813-2460
  • Cesiulis, Henrikas|||0000-0002-5077-7884
  • Gebert, Annet
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
  • Hansal, Wolfgang
  • Kautek, Wolfgang|||0000-0003-2772-2049
A detailed electrochemical study and investigation of a Fe-P glycine bath as a function of the temperature and glycine concentrations and current density, and their resulting corrosion and mechanical behavior is presented. A low addition of glycine to the electrolyte led to a drastic increase of the P content. At low Fe-P deposition rates, heterogeneous rough deposits with morphological bumps and pores were observed. By increasing the Fe-P deposition rate, the number of pores were reduced drastically, resulting in smooth coatings. Increasing the P content led to the formation of nanocrystalline grains from an "amorphous-like" state. Coatings with higher P contents exhibited better corrosion resistance and hardening, most likely attributed to grain boundary strengthening.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Strain gradient mediated magnetoelectricity in Fe-Ga/P(VDF-TrFE) multiferroic bilayers integrated on silicon

  • Nicolenco, Aliona|||0000-0003-4624-2163
  • Gómez, Andrés|||0000-0003-2847-0138
  • Chen, Xiangzhong|||0000-0002-2294-7487
  • Menéndez, Enric|||0000-0003-3809-2863
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Pané i Vidal, Salvador|||0000-0003-0147-8287
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
The primary advantage of magnetoelectric heterostructures exhibiting direct magnetoelectric effect is the possibility to induce and modulate the electrical response of the ferroelectric phase directly with an external magnetic field (i.e., wirelessly, without applying electric field). Nevertheless, the magnetoelectric coupling in such heterostructures is commonly limited by substrate clamping which hinders effective strain propagation. In this work, 1 μm thick ferromagnetic Fe-Ga layers were electrodeposited onto rigid Si/Cu substrates and subsequently coated with ferroelectric P(VDF-TrFE). Under magnetic field, the (110) textured Fe-Ga alloy is compressed along the z-direction by 0.033%, as demonstrated by X-ray diffraction. The experimental results suggest that while the bottom of the Fe-Ga layer is clamped, its air side exhibits a pronounced tetragonal deformation thanks to the residual nanoporosity existing between the columnar grains, that is, a strain gradient develops across the thickness of the Fe-Ga film. This strain gradient in Fe-Ga induces a change in the piezoresponse of the adjacent ferroelectric P(VDF-TrFE) layer. These results pave the way to the design of high-performance microelectromechanical systems (MEMS) with magnetoelectric response integrated on rigid substrates.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Tailoring magnetic and mechanical properties of mesoporous single-phase Ni-Pt films by electrodeposition

  • Eiler, Konrad|||0000-0001-8648-6395
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Navarro Senent, Cristina Maria|||0000-0002-7757-0357
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Homogeneous mesoporous Ni-rich Ni-Pt thin films with adjustable composition have been synthesised by one-step micelle-assisted electrodeposition. The films exhibit a face-centred cubic solid solution (single phase) and their magnetic and mechanical properties can be tuned by varying the alloy composition. In particular, the Curie temperature (TC) is shown to decrease with the Pt content and thin films with a TC close to room temperature (i.e. Ni58Pt42) and below can be produced. Hysteresis loops show a decrease of saturation magnetisation (Ms) and coercivity (Hc) with decreasing Ni content. A comparison of porous and dense films reveals significantly lower saturation magnetic field strength for porous films. Concerning mechanical properties, mainly two trends can be observed: a decrease of the Young's modulus of the nanoporous films with respect to dense films by 10% in average and a progressive increase of Young's modulus with the Ni content from 4.2 GPa to 5.7 GPa in both types of films. The tunability of properties and facility of synthesis make this alloy a promising material for microelectromechanical systems (MEMS).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Synthesis of α-Fe2O3 and Fe-Mn oxide foams with highly tunable magnetic properties by the replication method from polyurethane templates

  • Feng, Yuping
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Zhang, Huiyan
  • Solsona, Pau|||0000-0001-9274-2447
  • Baró, M. D.|||0000-0002-8636-1063
  • Suriñach, Santiago|||0000-0001-8125-0594
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Open cell foams consisting of Fe and Fe-Mn oxides are prepared from metallic Fe and Mn powder precursors by the replication method using porous polyurethane (PU) templates. First, reticulated PU templates are coated by slurry impregnation. The templates are then thermally removed at 260 °C and the debinded powders are sintered at 1000 °C under N2 atmosphere. The morphology, structure, and magnetic properties are studied by scanning electron microscopy, X-ray diffraction and vibrating sample magnetometry, respectively. The obtained Fe and Fe-Mn oxide foams possess both high surface area and homogeneous open-cell structure. Hematite (α-Fe2O3) foams are obtained from the metallic iron slurry independently of the N2 flow. In contrast, the microstructure of the FeMn-based oxide foams can be tailored by adjusting the N2 flow. While the main phases for a N2 flow rate of 180 L/h are α-Fe2O3 and FeMnO3, the predominant phase for high N2 flow rates (e.g., 650 L/h) is Fe2MnO4. Accordingly, a linear magnetization versus field behavior is observed for the hematite foams, while clear hysteresis loops are obtained for the Fe2MnO4 foams. Actually, the saturation magnetization of the foams containing Mn increases from 5 emu/g to 52 emu/g when the N2 flow rate (i.e., the amount of Fe2MnO4) is increased. The obtained foams are appealing for a wide range of applications, such as electromagnetic absorbers, catalysts supports, thermal and acoustic insulation systems or wirelessly magnetically-guided porous objects in fluids.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Structural and magnetic properties of FexCu1-x sputtered thin films electrochemically treated to create nanoporosity for high-surface-area magnetic components

  • Robbennolt, Shauna|||0000-0001-5723-7971
  • Fornell Beringues, Jordina|||0000-0002-0909-3843
  • Quintana, Alberto|||0000-0002-9813-735X
  • Zhang, Huiyan
  • Menéndez, Enric|||0000-0003-3809-2863
  • Pellicer, Eva|||0000-0002-8901-0998
  • Sort, Jordi|||0000-0003-1213-3639
Sputter deposition is a facile and widely used technique for fabricating thin-film materials. Electrochemical dealloying, on the other hand, is a promising method for creating nanoporosity, and therefore increasing surface area, in metallic materials. Surprisingly, little work has been done on the application of electrochemical dealloying to sputter-deposited thin films. Here, we prepare FexCu1-x thin films by sputter deposition to be then electrochemically treated to create porosity. We investigate the structural and magnetic properties of as-sputtered and electrochemically treated films. We find that the morphology, crystal structure, and magnetic properties are highly dependent on initial film composition. For high copper content films (Fe29Cu71), relative Cu content is found to decrease during the dealloying process. For these films, the crystal structure is not greatly affected by the induced porosity and the porous films show increased saturation magnetization. However, for the more Fe-rich compositions (Fe63Cu37), we find that Fe is preferentially lost and making the films nanoporous induces a crystal structure change from body-centered cubic (bcc) to a mixture of face-centered cubic (fcc) and bccphases. These same porous films show a decrease in saturation magnetization and a large increase in coercivity compared to the as-sputtered films. These films are attractive as high-surface-area magnetic components because of the tunability of their magnetic properties and their high surface area due to porosity. To the best of our knowledge, these results constitute the first example of nanoporous, magnetic thin films by prepared by sputtering and subsequent electrochemical treatment.