Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of the heat treatment on the microstructure and hardness evolution of a AlSi10MgCu alloy designed for laser powder bed fusion

  • Martin, Arturo
  • San Sebastián, María
  • Gil, E.
  • Wang, C.Y.
  • Milenkovic, Srdjan
  • Pérez Prado, María Teresa
  • Cepeda-Jiménez, C.M.
The aim of this work is to investigate the influence of the addition of Cu on the microstructure and on the microhardness of a laser powder bed fusion (L-PBF)-fabricated AlSi10MgCu alloy. With this goal, AlSi10Mg+4 wt%Cu pre-alloyed powder was produced by gas atomization. Following a parameter optimization study, dense as-built specimens with a high relative density of 99.8% were fabricated. An outstanding microhardness value, exceeding 180 HV, was obtained after aging at 160 °C for 16 h. This value is similar to that of the high strength Al 7075 in the T6 condition. With the aid of analytical transmission electron microscopy, it was concluded that the origin of the observed excellent mechanical behavior could be attributed to the beneficial effect of Cu in reducing the Al-matrix cell size, and in increasing the density and decreasing the size of the Si-based nanoprecipitates at cell interiors. More specifically, it is proposed that the maximum hardness is associated to the development of Cu-rich GP-I zones, which act as precursors of Si nanoprecipitates. Overaging leads to a reduction in microhardness due to transformation of these GP-I zones into coarser θ’’ precipitates and thus to a smaller volume fraction of larger Si-based nanoparticles., This work was funded by the European Union's Horizon 2020 Clean Sky 2 research and innovation program under grant agreement No 755610, project AlForAMA. The authors acknowledge the support from the topic manager, Leonardo Aircraft. CYW acknowledges the financial support from the Fundamental Research Funds for the Central Universities in China (grant number 3102019QD0415). MTPP would like to acknowledge funding from the Madrid region under the program S2018/NMT-4381-MAT4.0-CM.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The relation between ductility at high temperature and solid solution in Mg alloys

  • Cepeda-Jiménez, C.M.
  • Shi, D.F.
  • Pérez Prado, María Teresa
This work investigates the effect of solid solution on ductility and on the activation of individual deformation mechanisms at moderate temperatures and at quasi-static strain rates in Mg-Zn and Mg-Al alloys. With that aim, four solid solution Mg-Zn and Mg-Al binary alloy ingots containing 1 and 2 wt.% solute atoms were subjected to hot rolling and subsequent annealing to generate polycrystals with similar average grain size and basal-type texture for each composition. The activity of the different slip systems after tensile testing at 150°C and at 250°C was evaluated in pure Mg and in the alloys by EBSD-assisted slip trace analysis. In addition, segregation of Zn and Al atoms at grain boundaries during the thermo-mechanical processing was characterized by HAADF-STEM and EDX. It was found that while the addition of Al and Zn atoms to pure Mg does not lead to major changes in the mechanical strength at the investigated temperatures, it does enhance ductility significantly, especially at 250°C. Our results show that this increase in ductility cannot be attributed to a higher activation of non-basal systems in the alloys, as reported earlier, as the incidence of non-basal systems is indeed considerably higher in pure Mg. This work suggests, on the contrary, that the ductility increase may be attributed to the presence of a more homogenous basal activity in the alloys due to a lower degree of orientation clustering, to grain boundary solute segregation, and to a higher slip diffusivity at grain interiors., The research leading to these results has received funding from the Madrid region under programme S2018/NMT-4381-MAT4.0-CM project. Funding from projects PID2019-111285RB-I00 and PID2020-118626RB-I00 awarded by the Spanish Ministry of Science, Innovation and Universities, is also acknowledged. DFS acknowledges the financial support from the China Scholarship Council (Grant no 201706050154).
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Effect of Solute Content and Temperature on the Deformation Mechanisms and Critical Resolved Shear Stress in Mg-Al and Mg-Zn Alloys

  • Wang, De-Yi
  • Li, Na
  • Alizadeh Balochi, Reza
  • Monclús, M. A.
  • Cui, Yuwen
  • Molina Aldareguía, Jon M.|||0000-0003-3508-6003
  • Llorca Martinez, Francisco Javier|||0000-0002-3122-7879
Archivo Digital UPM
Publicación Contribución de congreso (ConferenceOutput)

Integrated Analysis and Quality Control of Laser-Based Additive Manufacturing Processes

  • Ocaña Moreno, José Luis|||0000-0001-9263-8404
  • Cordovilla Baró, Francisco|||0000-0001-7438-2804
  • García Beltrán, Ángel|||0000-0003-1900-0222
  • Vicente Oliva, Jesús de
  • Porro González, Juan Antonio|||0000-0001-5260-527X
  • Díaz Muñoz, Marcos|||0000-0001-7751-4913
  • Tapia Fernández, Santiago|||0000-0002-1418-9276
  • Angulo Ramonell, Ignacio
  • Díaz, J.
  • Álvarez, P.
  • Montealegre, M. A.
  • Garzón, M.
  • Muñoz, D. A.
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

The effect of temperature on the high-strain-rate response of Co-Al-W- base alloys: experiments and modeling

  • Casas Ferreras, Rafael|||0000-0001-5649-2161
  • Sancho Cadenas, Rafael|||0000-0002-7635-0483
  • Campos Gómez, Mónica|||0000-0002-8360-9561
  • Gálvez Díaz-Rubio, Francisco|||0000-0003-2894-935X
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

A Methodology to Automatically Segment 3D Ultrasonic Data Using X-ray Computed Tomography and a Convolutional Neural Network

  • Caballero Garzón, Juan Ignacio|||0000-0003-3759-6146
  • Cosarinsky, Guillermo|||0000-0002-6148-7612
  • Camacho, Jorge|||0000-0001-7528-558X
  • Menasalvas Ruiz, Ernestina|||0000-0002-5615-6798
  • Gonzalo Martí­n, Consuelo|||0000-0002-0804-9293
  • Sket, Federico|||0000-0001-5075-3180
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

A deep encoder-decoder for surrogate modelling of liquid moulding of composites

  • Fernández León, Joaquín|||0000-0003-3822-4715
  • Keramati, Keayvan|||0000-0003-3781-5361
  • Miguel, C
  • González Martínez, Carlos Daniel|||0000-0002-0724-138X
  • Baumela Molina, Luis|||0000-0001-6910-4359
Archivo Digital UPM
Publicación Tesis doctoral (DoctoralThesis)

Improving the characterization of porosity by ultrasonic testing in composite materials using X-ray computed tomography, machine learning and signal processing

  • Caballero Garzón, Juan Ignacio|||0000-0003-3759-6146
Archivo Digital UPM
Publicación Contribución de congreso (ConferenceOutput)

The Role of Process Design and Modelling in the Quality Assurance of Additively Manufactured Metallic Components

  • Ocaña Moreno, José Luis|||0000-0001-9263-8404
  • Cordovilla Baró, Francisco|||0000-0001-7438-2804
  • Angulo Ramonell, Ignacio
  • García Beltrán, Ángel|||0000-0003-1900-0222
  • Radhakrishnan, J.
  • Warzanskyj Prieto, Wsewolod|||0000-0002-7121-2022
  • Díaz Muñoz, Marcos|||0000-0001-7751-4913
  • Porro González, Juan Antonio|||0000-0001-5260-527X
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

A Machine Learning Strategy for Race-Tracking Detection During Manufacturing of Composites by Liquid Moulding

  • Fernández León, Joaquín|||0000-0003-3822-4715
  • Keramati, Keayvan|||0000-0003-3781-5361
  • Garoz Gómez, David|||0000-0003-2110-0118
  • Baumela Molina, Luis|||0000-0001-6910-4359
  • Miguel Giraldo, Carlos de
  • González Martínez, Carlos Daniel|||0000-0002-0724-138X