Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Non-linear finite element formulation applied to thermoelectric materials under hyperbolic heat conduction model

  • Palma, Roberto
  • Pérez-Aparicio, José L.
  • Taylor, R.L.
In the present work, a three-dimensional, dynamic and non-linear finite element to simulate thermoelectric behavior under a hyperbolic heat conduction model is presented. The transport equations, which couple electric and thermal energies by the Seebeck, Peltier and Thomson effects, are analytically obtained through extended non-equilibrium thermodynamics, since the local equilibrium hypothesis is not valid under the hyperbolic model. In addition, unidimensional analytical solutions are obtained to validate the finite element formulation. Numerically, isoparametric eight-node elements with two degrees of freedom (voltage and temperature) per node are used. Non-linearities due to the temperature-dependence on the transport properties and the Joule effects are addressed with the Newton-Raphson algorithm. For the dynamic problem, HHT and Newmark-ß algorithms are compared to obtain accurate results, since numerical oscillations (Gibbs phenomena) are present when the initial boundary conditions are discontinuous. The last algorithm, which is regularized by relating time steps and element sizes, provides the best results. Finally, the finite element implementation is validated, comparing the analytical and the numerical solutions, and a three-dimensional example is presented., This research was partially supported by the Spanish Ministry of Education through Grant No. FPU AP-2006-02372 and also from Grants MICINN BIA-2008-00522, CSD2008-00037 Canfranc Under-ground Physics, Excelencia Junta Andalucia P08-TEP-03641 and "Ayudas Investigacion" from UPV. The authors would also like to thank Prof. Guillermo Rus for his valuable contributions.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Exact, integrated and complete solutions for composite flywheels

  • Pérez-Aparicio, José L.
  • Ripoll, L.
An integrated general formulation for the analysis and design of flywheel rotors made out of composite material is developed. To have an accurate estimation of stresses in the rotor, all the effects present in the literature and some new ones have been included: axial length (disks vs. cylinders), acceleration (sudden energy releases), hub stiffness and mass (attachment), non-uniform curing (different temperature inside, outside rotor) and moisture absorption (transient, permanent). Through pertinent transformations, these effects are described by a single differential equation that can be directly integrated, giving closed-form expressions for displacements, stresses and failure factors. The new formulation is applied to the study of a standard rotor of the type commonly analyzed in the literature, uni- and multilayer, made out of glass and carbon fiber/epoxy materials. The results are compared with those corresponding to each of the effects, drawing conclusions and design recommendations. © 2010., This work was partially supported by the Grants: Excelencia Junta Andalucia P08-TEP-3641, MCyT DPI 2002-04472-C02 and the "Ayudas Investigacion" from UPV2010.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental design of dynamic model-based damage identification in piezoelectric ceramics

  • Rus, Guillermo
  • Palma, Roberto
  • Pérez-Aparicio, José L.
[EN] A model-based inverse problem strategy is proposed for damage characterization, starting from the electromechanical response measurement as input data, and incorporating a numerical model that simulates the piezoelectric response. Furthermore, a sensitivity analysis is developed to provide a rational basis to correctly design the excitation/measurement system. The model-based inverse problem is solved by minimizing a cost functional using genetic algorithms. The cost functional or discrepancy is defined as the L-2 norm of the difference between experimental and simulated measurements. The latter are obtained by solving the forward problem, using a novel 2D dynamic piezoelectric finite element. The effects of measurement noise and model uncertainties are studied in detail through a sensitivity analysis, where a sensitivity factor is defined and implemented. The proposed inverse problem strategy reconstructs the defect characteristics with sufficient precision, under realistic levels of noise. © 2011 Elsevier Ltd. All rights reserved., The authors would like to thank the Ministerio de Innovacion y Ciencia, Spain, for the FPU Grant AP-2006-02372 and also from Grants Excelencia Junta Andalucia P08-TEP-3641, MCyT DPI 2002-04472-C02-02. Authors would also like to thank Prof. Rafael Gallego for his invaluable contributions to the development of the present work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of hysteretic thermoelectric behavior in photovoltaic materials using the finite element method, extended thermodynamics and inverse problems

  • Palma, Roberto
  • Pérez-Aparicio, José L.
  • Bravo, R.
The main objective of the present work is to develop and prove a theoretical explanation based on the Extended Non-Equilibrium Thermodynamics (ENETs) for the hysteretical thermoelectric behavior observed in certain thin-film photovoltaic materials. The ENET introduces dissipative fluxes in the entropy balance that could explain this behavior. To verify this explanation from a numerical point of view, results are generated using a Finite Element (FE) formulation based on the ENET and already developed in previous publications by the authors. In addition, an identification Inverse Problem (IP) is formulated; a cost function is defined as the quadratic difference between experimental and numerical results and the IP is solved minimizing the cost function using genetic algorithms. The conclusion is that the loop-like distributions are due to energy dissipation introduced by dissipative fluxes that are closely related with relaxation times. Also, the FE-IP combination permits to find an approximated characterization of properties for several materials from single experimental curves. Finally, several numerical simulations are proposed for laboratory experiments to further validate the theoretical interpretation and to confirm the relation between relaxation times and hysteresis., This research was partially supported by the Grants CSD2008-00037 Canfranc Underground Physics, Excelencia Junta Andalucia P08-TEP-03641 and Polytechnic University of Valencia under programs PAID 02-11-1828 and 05-10-2674.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the Accuracy of a Four-Node Delaminated Composite Plate Element and Its Application to Damage Detection. Article 061003

  • Fernández Casanova, César
  • Gallego-Molina, Antolino
  • Lázaro, Mario|||0000-0003-4949-8295
This paper presents a new four-node composite element, which incorporates nd delaminations through its thickness. Based on the extended finite element method (X-FEM) technology, the element is particularized on a CLT (classical laminate theory). Delamination is considered in the kinematic equations with additional degrees of freedom. The result is a four-node quadrilateral element requiring only two single FEM (finite element method) formulations, a bending one and a membrane one. An important result is that this formulation has the same accuracy as when separate elements are considered ( four region approach ). It is furthermore proven that the delaminated element passes the patch test if the selected FEM formulations to build the element pass the test in the pure single problems, making this methodology very attractive to develop other fractured elements. To illustrate this result, two benchmark problems were studied: first a complete delaminated cantilever plate, and second a complete delaminated circular plate. The element was tested in the context of SHM (structural health monitoring). Frequency shifts, damage indexes, and changes in mode shapes and frequency response functions (FRF) were obtained to quantify the severity of damage due to delamination., The authors thanks J. L. Perez-Aparicio for his financial support and the Spanish I + D National Plan "DPI2006-02970" Project, Junta de Andalucia "Proyecto de Excelencia P08-TEP-03641."
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Finite element analysis and material sensitivity of Peltier thermoelectric cells coolers

  • Pérez-Aparicio, José L.
  • Palma, Roberto
  • Taylor, R.L.
In this work, a finite element simulation of a commercial thermoelectric cell, working as a cooling heat pump, is presented. The specially developed finite element is three-dimensional, non-linear in its formulation (using quadratic temperature-dependence on material properties) and fully coupled, including the Seebeck, Peltier, Thomson and Joule effects. Another special interface finite element is developed to prescribe the electric intensity, taking advantage of repetitions and symmetries. A thorough study of the distributions of voltage, temperature and the corresponding fluxes is presented, and the performance of the cell is compared with that of the manufacturer and with simplified analytical formulations, showing a good agreement. Combining the finite element model with the Monte Carlo technique, a sensitivity analysis is presented to take into account the performance dependence on the material properties, geometrical parameters and prescribed values. This analysis, which can be considered a first step to optimize these devices, concludes that the temperature-dependence of the material properties of electric conductivity and Seebeck coefficient is very relevant on cell performance., This research was partially supported by the Ministry of Education through Grant FPU AP-2006-02372 and also from Grants MICINN BIA-2008-00522, MCyT DPI 2002-04472-C02-02 and Excelencia Junta Andalucia P08-TEP-3641.