Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Characterization of Functionalized Side-Chain Liquid CrystalMethacrylates Containing Nonmesogenic Units by DielectricSpectroscopy

  • Martinez-Felipe, Alfonso
  • Santonja Blasco, Laura
  • Badia, J.D.
  • Imrie, C.
  • Ribes-Greus, A.
[EN] The dielectric response of a series of side-chain liquid crystal copolymers, SCLCPs, the poly[6-(4'-methoxyazobenzene-4'-oxy)hexyl methacrylate]-co-poly[methyl methacrylate]s, MeOAzB/MMA copolymers, is presented in the frequency range f = 10(-2) to 107 Hz and over the temperature interval T = 150 to 120 degrees C. The relaxation spectra of these polymers have been studied in terms of the complex dielectric permittivity (epsilon' and epsilon '') and the dielectric loss tangent, tan(delta). The electric modulus, M*, has been also calculated. It is possible to distinguish two relaxations zones, one at low temperatures (including gamma and beta relaxations) and another at higher temperatures (including the alpha and beta 1 relaxations), all of them reported for liquid crystalline poly(methacrylate)s. The individual relaxations have been analyzed using Havriliak-Negami (HN) functions, and the effect of conductivity at high temperatures is subtracted. The thermal activation of the relaxations at low temperatures is studied using the Arrhenius equations as a function of copolymer composition, while the alpha and beta 1 relaxations are analyzed using Vogel-Tammann-Fulcher equations. The activation entropy has been also evaluated for all the relaxations through the Eyring equation. The temperature ranges, activation energies, and entropies of the relaxations at low temperatures (gamma and beta) are similar in the homopolymer and copolymers. However, the introduction of MMA units promotes variations in all the parameters related to the relaxations associated with the motions of the ester groups adjoining the polymer backbone. Specifically, a decrease is observed in the activation entropy values of the beta 1 relaxation, which suggests that the activation of the local motions of the side groups involves smaller cooperative regions in the copolymers with respect to the homopolymer. This fact may account for the extinction of the smectic behavior, together with the dilution of the anisotropic interactions between the mesogenic units on increasing MMA content. The study of this beta 1 relaxation can be then applied to anticipate the formation and stability of smectic phases in functionalized SCLCPs, by controlling the local mobility resulting in different mesogenic behavior., This paper is meant to be a tribute and recognition to the research activity of Professor Giulio Sarti. The authors would like to thank Dr. Victor Saenz de Juano for his advice during the discussion of the results and also the Spanish Ministry of Science and Innovation, through the Research Projects ENE2007-67584-C03, UPOVCE-3E-013, IT2009-0074, and ENE2011-28735-C02-01 and two FPI and FPU predoctoral grants, and the financial support of the Generalitat Valenciana, through the Grisolia and Forteza programs and the ACOMP/2011/189 program. UPV is also thanked for additional support through the PAID 05-09-4331 and PAID-06-11 programs.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A methodology to assess the energetic valorization of bio-based polymers from the packaging industry: pyrolysis of reprocessed polylactide

  • Badía Valiente, José David
  • Santonja Blasco, Laura
  • Martinez-Felipe, Alfonso
  • Ribes-Greus, A.|||0000-0003-2460-8291
The energetic valorization process of bio-based polymers is addressed in this study, taking polylactide (PLA) as model. The pyrolysis of virgin and multiple-injected PLA was simulated by means of multi-rate linear-non-isothermal thermogravimetric experiments. A complete methodology, involving control of gases, thermal stability and thermal decomposition kinetics was proposed. The release of gases was monitored by Evolved Gas Analysis of the fumes of pyrolysis, by in-line FT-IR, with the aid of 2D-correlation IR characterization. A novel model to establish the thermal stability of PLAs under any linear heating profile was proposed. A kinetic strategy was methodically applied to assess the thermal decomposition in terms of activation energy and kinetic model. It was found that the pyrolysis technologies for virgin PLA could be straightforwardly transferred for the valorization of its recyclates., The authors would like to acknowledge the Spanish Ministry of Science and Innovation for the financial support through the Research Projects ENE2007-67584-C03, UPOVCE-3E-013, ENE2011-28735-C02-01, IT-2009-0074, as well as for the pre-doctoral research position for L. Santonja-Blasco through the FPI program. The Spanish Ministry for Education is acknowledged for the concession of a pre-doctoral research position to J.D. Badia and A. Martinez-Felipe by means of the FPU program. The authors thank the financial support of the Generalitat Valenciana through the ACOMP/2011/189, the Grisolia research position for A. Martinez-Felipe, and for the Forteza technician position for J.D. Badia. Universitat Politecnica de Valencia (UPV, Spain) is thanked for additional support through the PAID 05-09-4331 and PAID 06-11-2037 projects. AIMPLAS is acknowledged for providing and processing the material. This paper is warmly dedicated to Gael Badia-Ombuena, in commemoration of his birth.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The role of crystalline, mobile amorphous and rigid amorphous fractions in the performance of recycled poly (ethylene terephthalate) (PET)

  • Badia, J.D.
  • Strömberg, Emma
  • Karlsson, Sigbritt
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The action of thermo-mechanical degradation induced by mechanical recycling of poly(ethylene terephthalate) was simulated by successive injection moulding cycles. Degradation reactions provoked chain scissions and a reduction in molar mass mainly driven by the reduction of diethyleneglycol to ethylene glycol units in the flexible domain of the PET backbone, and the formation of -OH terminated species with shorter chain length. The consequent microstructural changes were quantified taking into account a three-fraction model involving crystalline, mobile amorphous (MAF) and rigid amorphous fractions (RAF). A remarkable increase of RAF, to a detriment of MAF was observed, while the percentage of crystalline fraction remained nearly constant. A deeper analysis of the melting behaviour, the segmental dynamics around the glass-rubber relaxation, and the macroscopic mechanical performance, showed the role of each fraction leading to a loss of thermal, viscoelastic and mechanical features, particularly remarkable after the first processing cycle. © 2011 Elsevier Ltd. All rights reserved., The authors would like to acknowledge the Spanish Ministry of Science and Innovation for the financial support through the Research Project UPOVCE-3E-013 and for the funding of a pre-doctoral research position to J.D. Badía by means of the FPU program conceded by the Spanish Ministry for Education. Catalana de Polimers, S.A. and AIMPLAS are acknowledged for providing and processing the material, respectively. Mr. Peter Kaali is thanked for carrying out impact tests and Mrs. Sevil Atari Jabarzadeh for helping with SEM analysis. The authors thank the financial support of the Generalitat Valenciana through the ACOMP/2011/189 and the Gerónimo Forteza grant to J.D. Badía. Universitat Politècnica de València (UPV, Spain) is thanked for additional support through the PAID 05-09-4331 program and Royal Institute of Technology (KTH, Sweden) is thanked for additional economical support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Material valorisation of amorphous polylactide. Influence of thermo-mechanical degradation on the morphology, segmental dynamics, thermal and mechanical performance

  • Badía Valiente, José David
  • Strömberg, Emma
  • Karlsson, Sigbritt
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] This paper reports the effects of multiple mechanical recycling on the structure and properties of amorphous polylactide (PLA). The influence of the thermo-mechanical degradation induced by means of five successive injection cycles was initially addressed in terms of macroscopic mechanical properties and surface modification. A deeper inspection on the structure and morphology of PLA was associated to the thermal properties and viscoelastic behaviour. Although FT-IR analysis did not show significant changes in functional groups, a remarkable reduction in molar mass was found by viscometry. PLA remained amorphous throughout the reprocessing cycles, but the occurrence of a cold-crystallization during DSC and DMTA measurements, which enthalpy increased with each reprocessing step, suggested chain scission due to thermo-mechanical degradation. The effect of chain shortening on the glass-rubber relaxation studied by DMTA showed an increase in free volume affecting the segmental dynamics of PLA, particularly after the application of the second reprocessing step, in connection to the overall loss of performance showed by the remaining properties. © 2012 Elsevier Ltd. All rights reserved., The authors would like to acknowledge the Spanish Ministry of Science and Innovation for the financial support through the Research Project UPOVCE-3E-013 and for the funding of a predoctoral research position to J.D. Badia by means of the FPU program conceded by the Spanish Ministry for Education. The authors acknowledge the financial support of the Generalitat Valenciana through the ACOMP/2011/189. Universitat Politecnica de Valencia (UPV, Spain) is thanked for additional support through the PAID 05-09-4331 program and Royal institute of Technology (KTH, Sweden) is thanked for additional. Mr. Enrique Benavent at AIMPLAS is acknowledged for taking care of processing the material. Mr. Peter Kaali at KTH is thanked for carrying out impact tests and Mrs. Sevil Atari Jabarzadeh at KTH for helping with SEM analysis. Mrs. L. Santonja-Blasco at UPV is thanked for endless and enjoyable discussions.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Reprocessed polylactide: Studies of thermo-oxidative decomposition

  • Badía Valiente, José David
  • Santonja Blasco, Laura
  • Martinez-Felipe, Alfonso
  • Ribes-Greus, A.|||0000-0003-2460-8291
The combustion process of virgin and reprocessed polylactide (PLA) was simulated by multi-rate linear non-isothermal thermogravimetric experiments under O2. A complete methodology that accounted on the thermal stability and emission of gases was thoroughly developed. A new model, Thermal Decomposition Behavior, and novel parameters, the Zero-Decomposition Temperatures, were used to test the thermal stability of the materials under any linear heating rate. The release of gases was monitored by Evolved Gas Analysis with in-line FT-IR analysis. In addition, a kinetic analysis methodology that accounted for variable activation parameters showed that the decomposition process could be driven by the formation of bubbles in the melt. It was found that the combustion technologies for virgin PLA could be transferred for the energetic valorization of its recyclates. Combustion was pointed out as appropriate for the energetic valorization of PLA submitted to more than three successive reprocessing cycles, The authors would like to acknowledge the Spanish Ministry of Science and Innovation for the financial support through the Research Projects ENE2007-67584-C03, UPOVCE-3E-013, ENE2011-28735-C02-01, IT-2009-0074, as well as for the pre-doctoral research position for L. Santonja-Blasco through the FPI program. The Spanish Ministry for Education is acknowledged for the concession of a pre-doctoral research position to J.D. Badia and A. Martinez-Felipe by means of the FPU program. The authors thank the financial support of the Generalitat Valenciana through the ACOMP/2011/189, the Grisolia research position for A. Martinez-Felipe, and for the Forteza technician position. Universitat Politecnica de Valencia (UPV, Spain) is thanked for additional support through the PAID 05-09-4331 and PAID 06-11-2037 projects. AIMPLAS (Technological Institute of Plastic) is acknowledged for providing and processing the material.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A kinetic study of the formation of smectic phases in novel liquid crystal ionogens

  • Martinez-Felipe, Alfonso
  • Badia, J.D.
  • Santonja Blasco, Laura
  • Imrie, C.T.
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] A multi-rate non-isothermal kinetic analysis of the isotropic-melt to liquid crystalline phase transition of novel liquid crystalline ionogenic copolymers, LCIs, the 10-(4-methoxyazobenzene-4'-oxy)decyl methacrylate]-co-2-(acrylamido-2-methyl-1-propanesulfonic acid)s, 10-MeOAzB/AMPS, copolymers, has been performed by means of calorimetric experiments. An analytical methodology which includes the study of the phase transition rate parameter, the determination of the activation energies by using Kissinger and Flynn-Wall-Ozawa models, and the study of the phase transition kinetics by the use of the Avrami theory, has been applied. The formation of the mesophases from the isotropic state occurred close to thermodynamic equilibrium. The results evidence the presence of several individual processes in the formation of liquid crystalline phases from the melt and a strong dependence of phase transition rates and activation energies with acid contents. A decrease in the phase transition rate, related to a decrease in the overall change of the transition entropy, has been observed. The final inhibition of the liquid crystal (LC) behaviour is ascribed to an exponential increase in the activation energy of the phase transition, promoted by strong acid aggregation. An optimum composition of the 10-MeOAzB/AMPS copolymers to achieve the dual characteristics of LCIs (ionogenic and liquid crystalline behaviour) requires acid concentrations capable of promoting structure-forming effects on the LC phases and the evolution of phase separated morphologies., The authors would like to acknowledge the Spanish Ministry of Science and Innovation, through the Research Projects ENE2007-67584-C03, UPOVCE-3E-013, ENE2011-28735-C02-01, IT-2009-0074 and three FPI and FPU predoctoral grants, and the financial support of the Generalitat Valenciana, through the Grisolia and Forteza programs and the ACOMP/2011/189 program. The Vice-rectorate for Research of UPV is also thanked for additional support through the PAID 05-09-4331, PAID-05-11/2806, and PAID 06-11-2037 projects.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hygrothermal ageing of reprocessed polylactide

  • Badia, J.D.
  • Santonja Blasco, Laura
  • Martinez-Felipe, Alfonso
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] The influence of an accelerated hygrothermal ageing simulation test on a commercial PLA and its three subsequent mechanically-reprocessed materials was studied. The analysis was focused on the water diffusion kinetics and the physico-chemical changes induced by the hygrothermal degradation. Water diffusion proceeded faster than chain relaxation processes, as defined by a Case II absorption model. It was proved that the water diffusion rate decreased with subsequent reprocessing cycles and increased with higher hygrothermal ageing temperatures. Hydrolytic chain scission provoked significant molar mass decays and consequent general losses of thermal and mechanical performance. The rearrangement into crystalline fractions of shorter chains provoked by hygrothermal ageing was qualitatively and quantitatively followed by both Fourier-Transform Infrared Spectroscopy and Differential Scanning Calorimetry. The microstructural changes were monitored by the cold-crystallization temperature, the crystallinity degree XC and the absorbance intensity ratio I921/I955. A Weibull model showed that the crystallites were formed faster at higher reprocessing cycles and at lower hygrothermal ageing temperatures. All these effects were particularly significant for PLA reprocessed more than one time., B.Sc. Oscar Gil-Castell is acknowledged for his dedication in the lab and his outstanding attitude towards learning. The authors thank the Spanish Ministry of Science and Innovation, through the Research Projects ENE2011-28735-C02-01 and UPOVCE-3E-013, the Ministry of Education and Science for the awarding of the FPI pre-doctoral grant to L. Santonja-Blasco and FPU pre-doctoral grants to A. Martinez-Felipe and J.D. Badía. The financial support of the Generalitat Valenciana, through the Grisolia (A. Martinez-Felipe) and Forteza (J.D. Badia) programs and the ACOMP/2011/189. UPV is thanked for additional support through the PAID 05-09-4331 program and the PAID 04-11 for the allowance conceded to attend to the III International Conference on Biodegradable and Biobased Polymers (BIOPOL2011) in Strasbourg.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of Structure Formation in Side-Chain Liquid Crystal Copolymers by Variable Temperature Fourier Transform Infrared Spectroscopy

  • Martinez-Felipe, Alfonso
  • Imrie, Corrie Thomas
  • Ribes-Greus, A.|||0000-0003-2460-8291
The formation of smectic phases in side-chain liquid crystal copolymers, SCLCPs, containing sulfonic acid-based nonmesogenic units, has been investigated using variable temperature FT-IR microscopy. Two copolymers have been characterized, namely, the poly[10-(4-methoxy-4′-oxy-azobenzene) decyl methacrylate]−copoly[2-acrylamido-2-methyl-1- propanesulfonic acid]s, the X-MeOAzB/AMPS copolymers, containing X = 0.71 and 0.56 mol fraction of mesogenic sidechains, respectively. For comparative purposes the corresponding side chain liquid crystal homopolymer, poly[10-(4-methoxy-4′- oxy-azobenzene) decyl methacrylate], MeOAzB, has also been characterized. The 0.56-MeOAzB/AMPS copolymer exhibits a bilayer smectic A phase, in which the mesogenic side chains constitute one layer with a SmA1 packing arrangement and the sulfonic acid groups another; whereas in the smectic A phase shown by the 0.71-MeOAzB/AMPS copolymer, the acid groups are located within the smectic layers giving a partially interdigated SmAd phase and reducing side chain packing efficiency. Smectic stabilization is attributed to a combination of stronger interactions involving the ester groups, as reflected in changes to the C O stretching band at ν ∼ 1730 cm−1 , and hydrogen bonding between the amide groups within the acid-based layers, as inferred by changes to the NH stretching band at ν ∼ 3320 cm−1 . The temperature response observed for groups with different chemical environments permits the mapping of the short-range interactions between the various structural components in SCLCPs with a view to controlling the functionality of the materials., This paper is meant to be a tribute and recognition to the research activity of Professor Giulio Sarti. The authors also thank the Spanish Ministry of Science and Innovation, through the Research Projects ENE2007-67584-C03, UPOVCE-3E-013, IT2009-0074, ENE2011-28735-C02-01 and two FPI and FPU predoctoral grants, and the financial support of the Generalitat Valenciana, through the Grisolia (GRISOLIAP/2010/057, GRISOLIAP/2012/056, GRISOLIAP/2013/A/036) and Forteza programs and the ACOMP/2011/189 program. The UPV is also thanked for additional support through the PAID 05-09-4331 and PAID-06-11 program.