Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 21
Encontrada(s) 1 página(s)

Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Electric field as a useful tool to improve the poor adsorption affinity of pollutants on carbonaceous aerogel pellets

  • Puga Pazo, Antón
  • Meijide Fernandez, Jessica
  • Pazos Currás, Marta María
  • Rosales Villanueva, Emilio
  • Sanromán Braga, María Ángeles
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, The removal of ionisable drugs (fluoxetine, sulfamethizole and antipyrine) from aqueous solution was performed by conventional adsorption using carbonaceous aerogel pellets as adsorbents. Although >96 % elimination was achieved for sulfamethizole and antipyrine after 1440 min, only 2.5 % fluoxetine was removed. In a multicomponent system, the presence of these three drugs in the solution leads to a fivefold depletion of the adsorbed total mass. Thus, the authors proposed to influence the traditional adsorption process by an electric field to improve the low affinity of fluoxetine to the aerogel. Specifically, the electrosorptive removal of fluoxetine was investigated by applying different voltages between 0.8 and 1.3 V, with the maximum adsorption achieved at 1.2 V. The application of an electric field increases the affinity of the contaminants to aerogel pellets. After demonstrating the applicability of the electrosorption in the removal of fluoxetine, the effect of the water matrix on the process was analysed. For this purpose, the removal of these ionisable drugs was evaluated using real wastewater, specifically, raw wastewater and wastewater after primary and tertiary treatment from a municipal wastewater treatment plant. As expected, pollutant removal was somewhat lower due to the complexity of the water matrix. Total percent removal of all pollutants was achieved using only the effluent treated water as the matrix due to minimal competitive adsorption. Finally, the Microtox® test confirmed the excellent ability of this approach to remove these pharmaceuticals, resulting in luminescence inhibition that decreased by 60–80 % depending on the water matrix compared to the polluted influent., Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Agencia Estatal de Investigación | Ref. PID2020-113667 GB-I00, Xunta de Galicia | Ref. ED431C 2021-43, Xunta de Galicia | Ref. ED481B 2018/096
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Thin-film photoreactor with hydrogel-immobilized carbon dot-functionalized graphitic carbon nitride for pollutant degradation

  • Fernández Sanromán, Antía
  • Otero Romero, David
  • Pazos Currás, Marta María
  • Rosales Villanueva, Emilio
This study reports the development of a sustainable, metal-free photocatalytic system for degrading emerging pollutants in water. A novel photocatalyst based on graphitic carbon nitride modified with carbon dots and amine-functionalized (GCN@CD-A) was synthesized to enhance visible-light absorption and charge separation, resulting in improved photocatalytic activity. The GCN@CD-A composite was immobilized within biopolymer hydrogels composed of carboxymethylcellulose (CMC) and sodium alginate (SA) to address the recovery and reuse limitations associated with powdered catalysts. Different CMC:SA ratios were tested to optimize the mechanical stability and photocatalytic performance of the hydrogel matrix. Among them, ratio 1:1 provided the best balance between structural integrity and catalytic efficiency, maintaining degradation performance comparable to the powdered catalyst toward model pollutants such as Rhodamine B, paracetamol, and acebutolol. Comprehensive material characterization confirmed successful composite formation and effective catalyst immobilization, while scavenger experiments identified superoxide radicals as the dominant reactive radical. The optimized hydrogel was subsequently integrated into a 3D-printed inclined thin-film photoreactor designed to enhance light exposure and mass transfer under laminar flow conditions. Photocatalytic performance was evaluated in recirculation mode using different water matrices, including ultrapure water, tap water, and secondary effluent. Complete degradation of the target pollutants was achieved under visible light irradiation, although reaction efficiency was influenced by water matrix complexity. Overall, this integrated approach demonstrates a scalable, eco-friendly solution for advanced water treatment, combining efficient pollutant degradation with improved catalyst reusability and practical applicability., Agencia Estatal de Investigación | Ref. PID2023-146133NB-I00, Xunta de Galicia | Ref. ED431C 2025/47, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Agencia Estatal de Investigación | Ref. PRE2021-098540, Xunta de Galicia | Ref. ED481B 2025/057, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Heterogeneous advanced oxidation processes: current approaches for wastewater treatment

  • Lama Rodriguez, Gabriela
  • Meijide Fernandez, Jessica
  • Sanromán Braga, María Ángeles
  • Pazos Currás, Marta María
Nowadays, water pollution is one of the most dangerous environmental problems in the world. The presence of the so-called emerging pollutants in the different water bodies, impossible to eliminate through conventional biological and physical treatments used in wastewater treatment plants due to their persistent and recalcitrant nature, means that pollution continues growing throughout the world. The presence of these emerging pollutants involves serious risks to human and animal health for aquatic and terrestrial organisms. Therefore, in recent years, advanced oxidation processes (AOPs) have been postulated as a viable, innovative and efficient technology for the elimination of these types of compounds from water bodies. The oxidation/reduction reactions triggered in most of these processes require a suitable catalyst. The most recent research focuses on the use and development of different types of heterogeneous catalysts, which are capable of overcoming some of the operational limitations of homogeneous processes such as the generation of metallic sludge, difficult separation of treated water and narrow working pH. This review details the current advances in the field of heterogeneous AOPs, Fenton processes and photocatalysts for the removal of different types of emerging pollutants., Ministerio de Ciencia e Innovación | Ref. PID2020-113667GB-I00, Ministerio de Ciencia e Innovación | Ref. PDC2021-121394-I00, Xunta de Galicia | Ref. ED481B 2018/096
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Structured organic frameworks as endocrine disruptor adsorbents suitable for Fenton regeneration and reuse

  • Díez Sarabia, Aida Maria
  • García Ocampo, Juanjo
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
  • Kolen’ko, Yury V.
New porous materials, such as metal-organic frameworks (MOFs) and covalent-organic frameworks (COFs), have been actively investigated due to their environmental applications. In this study, four of such structured materials, namely Fe3O4 @COF, MIL-53(Al), MIL-53(Al)-F127 and NH2-MIL-101(Fe) were synthetized. These materials have been tested for the first time for the adsorption in aqueous media of two endocrine disruptor pollutants, bisphenol A (BPA) and prednisolone (PDN). The adsorbents were characterized by the analysis of the point of zero charge (PZC), the functional groups (FTIR) and their physic-chemical structure (N2-isotherms, SEM, XRD and XPS). MIL-53-Al provided the highest uptake of both BPA (177.78 mg g− 1) and PDN (280.70 mg g− 1) even when using a real wastewater matrix. Additionally, this MOF resulted to be a so-called catalytic-adsorbent, maintaining an appropriate adsorbent capacity after five regenerations cycles via Fenton-like process, causing only 20% and 5% adsorption detriment for BPA and PDN, respectively. This avoids spent adsorbent disposal issues and make this new kind of adsorbent to have the potential to be used in real environmental application scenarios., Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Xunta de Galicia | Ref. ED481D-2023/015, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Novel Fe-Ti nanoparticles synthesized in deep eutectic solvents for enhanced photo-electro-Fenton processes: Synergistic effects and environmental applications

  • Puga Pazo, Antón
  • Meijide Fernandez, Jessica
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
  • Rosales Villanueva, Emilio
An innovative titanium-magnetite (Fe-Ti) catalyst was developed using a production strategy based on water-free solvents such as deep eutectic solvents (DES) for the removal of persistent pollutants. The prepared catalyst was applied in electro-Fenton and photo-electro-Fenton processes. To this end, a new cell design with electrodes based on conductive materials was developed using 3D printing in two different electrochemical cells configurations: vertical electrode configuration (VEC) and horizontal electrode configuration (HEC). The HEC showed good performance attaining a yield hydrogen peroxide production of 20 mg⋅L1 and being able to operate in electro-Fenton degradation batch assays for the removal of the drugs (Antipyrine and Lissamine Green B). Then, the heterogeneous bimetallic catalyst (BC-FeTi) was tested and compared with the monometallic Fe catalyst (MCFe). The results with both catalysts showed a synergistic effect combining electrochemical oxidation and Fenton reaction, promoting the best removal of the target pollutants. Subsequently, the contribution of UV radiation was evaluated with BC-FeTi, achieving that more than 80 % of both pollutants were removed in 80 min by the photo- Fenton process, confirming the high affinity of oxidizing free radicals for high molecular weight organic molecules. Finally, the simultaneous application of electro- and photo-oxidation (photo-electro-Fenton) significantly improved the removal of the target contaminants from the aqueous solution, achieving complete removal in 50 and 80 min for Lissamine Green B and Antipyrine, respectively. The stability and reusability of BC-FeTi and 3Dprinted electrodes were achieved in five successive working cycles, with negligible loss of activity compared to new catalysts, which achieved greater than 99 % removal after five consecutive runs. Leaching of iron and titanium from the catalyst evaluated throughout the cycles, was low, totalling 2.7 and 4.5 % at the end of the fifth cycle., Agencia Estatal de Investigación | Ref. PCI2022-132941, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Xunta de Galicia | Ref. ED481B 2018/096, Xunta de Galicia | Ref. ED431C 2021-43, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Anti-inflammatory drug diclofenac removal by a synthesized MgAl layered double hydroxide

  • Mkaddem, H.
  • Rosales Villanueva, Emilio
  • Pazos Currás, Marta María
  • Ben Amor, H.
  • Sanromán Braga, María Ángeles
  • Meijide Fernandez, Jessica
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, Layered double hydroxides (LDHs) containing Mg:Al (molar ratio 3:1) were synthesized by coprecipitation from nitrate salts under alkaline conditions. Their further characterisation by different techniques allowed the determination of their structural, nanotextural and chemical properties. XRD measurements confirmed the high crystallisation with the presence of two metal cations (Mg2+ and Al3+). The use of these materials as eco-friendly adsorbents was analysed to remove diclofenac from wastewater. Under optimal conditions (0.4 g L 1, 30 ppm initial pollutant concentration, pH 8.5), around 65% diclofenac removal was achieved after 60 min of treatment. The pseudo-second kinetic order model and Freundlich isotherm accurately described the experimental data, suggesting chemisorption process on the heterogeneous LDH surface. After diclofenac adsorption, XRD analysis revealed an increase in interlayer spacing followed by contraction of adjacent layers, so that anion exchange between layer was considered to be the main mechanism for diclofenac adsorption. Thermodynamic studies indicate diclofenac adsorption occurs spontaneously, endothermically, and also, with increasing randomness at the solid/solution surface. Batch test revealed limitations in terms of long-term stability of the material. Therefore, a post-synthesis strategy, calcination, was required to increase the degree of resistance. For this purpose, the effect of calcination temperature was examined in the range 200–300 C. Although, the kinetic rate constant decreased slightly after calcination, the improvement of its structural properties allowed to operate under continuous system., Ministerio de Ciencia e Innovación | Ref. PID2020- 113667 GB-I00, Ministerio de Ciencia e Innovación | Ref. PDC2021-121394-I00, Xunta de Galicia | Ref. ED431C 2021-43, Xunta de Galicia | Ref. ED481B 2018/096
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Application of deep eutectic solvents (DES) for the synthesis of iron heterogeneous catalyst: application to sulfamethoxazole degradation by advanced oxidation processes

  • Puga Pazo, Antón
  • Rosales Villanueva, Emilio
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
The development of novel approaches to the remotion of pharmaceuticals in wastewater is a subject of concern due to their effect on living beings and the environment. Advanced oxidation processes and the use of relevant catalysts are feasible treatment alternatives that require further development. The development of suitable heterogeneous catalysts is a necessity. This work proposes the synthesis of an iron catalyst in a deep eutectic solvent (Fe-DES) composed of choline chloride and citric acid, which was physically and chemically characterized using SEM-EDS and TEM, FTIR, RAMAN, XRD and XPS. The characterisation confirmed the presence of iron in the form of hematite. Fe-DES was shown to be a multipurpose catalyst that can be applied in the removal of sulfamethoxazole as a reagent in the Fenton and electro-Fenton processes and as an activator of peroxymonosulfate (PMS) processes. After testing the catalyst with the aforementioned techniques, the best result was achieved by combining these processes in an electro-PMS, with great efficiency achieved by dual activation of the PMS with the catalyst and electric field, attaining total elimination at natural pH in 90 min. Furthermore, the degradation was confirmed by the detection of short-chain carboxylic acids (oxalic, succinic, and acetic) and reduction in toxicity values. These results confirm the suitability of Fe-DES to degrade high-priority pharmaceutical compounds., Xunta de Galicia y FEDER | Ref. ED431C 2021-43, Ministerio de Ciencia e Innovación | Ref. PCI2022-132941, Ministerio de Ciencia e Innovación | Ref. PDC2021-121394-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

On-site regeneration by ultrasound activated persulfate of iron-rich Antipyrine-loaded biochar

  • Ouiriemmi , Imen
  • Escudero Curiel, Silvia
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, Adsorption process has proven its efficiency in the abatement of pharmaceuticals in liquid media, even if large volumes of wastewater need to be treated. Nevertheless, exhausted adsorbent regeneration is economically and environmentally necessary. For this reason, recent studies are aimed at finding new methods of regeneration. In this study, an on-site adsorption-regeneration method was assessed. Initially, a model pharmaceutical, Antipyrine (Apy), has been adsorbed onto a low-cost biochar. Apy adsorption followed a pseudo-second order kinetic and a Langmuir isotherm. In a second step, spent biochar was regenerated by oxidation using SO4- . To do this, SO4- was generated by activation of persulfate by ultrasound and assisted by the iron inherently into the biochar. To facilitate the availability of this iron, the addition of an enhancing agent such as oxalic acid was evaluated. The regenerated biochar proved its stability and reusability achieving an uptake percentage of around 87% after the third adsorption-regeneration cycle. Therefore, this on-site regeneration method could be promising for treating other kinds of adsorbents and resolving the pollution problems caused by the non-controlled throw of the exhausted adsorbents., Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Xunta de Galicia | Ref. ED431C 2021-43
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Pesticide abatement using environmentally friendly nano zero valent particles as photo-Fenton catalyst

  • Díez Sarabia, Aida Maria
  • Moreira, Manuela M.
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
  • Albergaria, T.
  • Delerue-Matos, C.
Nano-zero valent iron particles (NZVI) have been used for the pesticide pirimicarb degradation under simulated solar radiation. These particles have been synthesized by extracts from agro-industrial residues, namely vineyard and blueberry pruning, black tea and algae, so they can be labelled as “green-NZVI”. The physico-chemical properties of these green-NZVI were compared to those of NZVI synthesized with NaBH4. The usage of agroindustrial residues as reducing agent not only provided better performant NZVI but also evade the usage of harmful reagents. Indeed, this process is not only within circular economy, and environmentally friendly, but also defeats the degradation performance of the widely reported photo-Fenton process with Fe2+ catalyst. 96.5 % pirimicarb degradation was achieved under simulated solar radiation within 15 min with 0.08 mM H2O2 and 0.16 mM NZVI synthesized with black tea extract. Further, the developed process was optimized in terms of reagents concentration and natural antioxidant extract used for NZVI synthesis, which demonstrated a strong effect on pirimicarb degradation due to the differences on natural phenolic compounds present on them. The pirimicarb degradation pathway was analysed, confirming the successful pesticide degradation. In terms of H2O2 concentration, it can be reduced by its sequential addition in time. Under optimal conditions, even real effluents can be successfully degraded., Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Agencia Estatal de Investigación | Ref. PCI2022-132941, Fundação para a Ciência e a Tecnologia | Ref. UIDB/50006/2020, Fundação para a Ciência e a Tecnologia | Ref. UIDP/50006/2020, Xunta de Galicia | Ref. ED481D-2023/015, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Methodology for decentralized analysis: detection, quantification and in situ monitoring of pharmaceutical formulations removal by electro-Fenton

  • Caruncho Pérez, Sara
  • Prado Comesaña, Ana M.
  • Arellano Pardo, María
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
  • González Romero, Elisa
Water quality is essential to both human and ecosystem health, and a fast detection of emerging pollutants is claimed, along with effective wastewater treatment plants to eliminate these types of substances. The goal of this study was the development of a sensitive and selective methodology to customize a handle device that meets this demand. Clozapine and its pharmacological formulation, Leponex®, were used as a model. The results obtained from the studies by differential pulse voltammetry (DPV) demonstrated that this methodology allows a simpler and cheaper decentralized analysis without losing sensitivity, performing electrochemical measurements in situ, in real-time and directly without sample treatment, with a good precision (RSD 3.7 %) and excellent accuracy (recoveries between 97.6 and 99.9 %). Moreover, the methodology was successfully used for direct follow-up the medicine removal in real samples by electro-Fenton (EF) treatment. The results gathered showed a relative error of less than 2 % concerning the measurements made with the conventional potentiostat. Bearing this in mind, the effectiveness of these electrochemical techniques used in tandem with the comfort and high specificity offered by the portable device, a more exhaustive control of water quality can be achieved, thus improving the quality of life in the planet., Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Agencia Estatal de Investigación | Ref. CTM2017-87326-R, Xunta de Galicia | Ref. ED431C 2017/47, Xunta de Galicia | Ref. ED431D 2017/06
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Facile one-step synthesis of a versatile nitrogen-doped hydrochar from olive oil production waste, “alperujo”, for removing pharmaceuticals from wastewater

  • Escudero Curiel, Silvia
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, In line with the principles of zero waste and recycling, alperujo (AL) was used in this study to produce a value-added product: hydrochar (HC) with high adsorption capacity. An optimization of the hydrothermal carbonization (HTC) conditions, such as temperature, residence time, and water/solid ratio, was carried out to maximize the adsorption capacity. Eight HCs were obtained, and an in-depth comparative characterization, as well as adsorption tests of two pharmaceuticals with very different physicochemical properties (fluoxetine (FLX) and cefazolin (CFZ)), were performed. This first step allowed for elucidation of the best candidates to carry out nitrogen grafting on their surface, resulting in the HC obtained at a higher water/solid ratio and temperature, and longer residence time: 3-220°C-2.5 h with a maximum uptake of 4.6 and 0.4 mg/g for FLX and CFZ, respectively. After that, a facile one-step, one-pot synthesis of nitrogen-doped hydrochars (N-HC) was developed to prepare a versatile bio-adsorbent with enhanced adsorption capacity. Two N–HCs were prepared using urea (U-HC) and polyethyleneimine (PEI-HC) and were intensively characterized to shed light on the adsorption mechanism. In both cases, amide groups were formed, which favored the adsorption process. PEI-HC acquired an outstanding maximum adsorption capacity of 983.84 mg/g for CFZ, and 29.31 mg/g for FLX, and the process was well described by the Freundlich isotherm and pseudo-second-order kinetic model. A co-adsorption test was performed using PEI-HC for both pharmaceuticals, finding that the adsorption process occurs in different active sites because there was no interference between the pollutants. This fact corroborates the versatility of the new bio-adsorbent synthesized., Ministerio de Ciencia e Innovación | Ref. PID 2020- 113667GBI00, Ministerio de Ciencia e Innovación | Ref. PDC 2021-121394-I00, Xunta de Galicia | Ref. ED431C 2021-43, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Heterogeneous electro-Fenton system using Fe-MOF as catalyst and electrocatalyst for degradation of pharmaceuticals

  • Fernández Sanromán, Antía
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
  • Rosales Villanueva, Emilio
In recent years, heterogeneous electro-Fenton processes have gained considerable attention as an alternative to homogeneous processes. In this context, the aim of this study is the use of a commercial iron metal-organic framework (Fe-MOF), Basolite® F-300, as a base material for the design of a heterogeneous electro-Fenton treatment system for the removal of antipyrine. Initially, the catalyst was applied as powder in aqueous solution and three key parameters of the electro-Fenton process (pH, Fe-MOF concentration and current density) were evaluated and optimized by a Central Composite Design Face Centred (CCD-FC) using antipyrine removal and energy consumption as response functions. Near complete antipyrine removal (94%) was achieved under optimal conditions: pH 3, Fe-MOF 157.78 mg/L and current density 6.67 mA/cm2, obtaining an energy consumption of 0.29 W·h per mg of antipyrine removed. Later, two electrocatalysts (Fe-MOF functionalized cathodes), prepared by different Fe-MOF immobilisation approaches (composite of carbon black/polytetrafluoroethylene or by electrospinning on Ni foam), were synthesized. Their characterisation showed notable Fe-MOF incorporation into the material and favourable properties as electrocatalysts. Both Fe-MOF functionalized cathodes were evaluated in the removal of antipyrine at different pH (acidic and natural) and current density (27.78 and 55.56 mA/cm2), achieving in the best conditions removal levels around 80% in 1 h without any operational problems. In addition, several intermediates generated during the treatment were identified and their toxicity estimated. According to the obtained results, the degradation compounds have less toxicity than the parent compounds, confirming the effectiveness of the treatment., Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Xunta de Galicia | Ref. ED431C 2021–43, Agencia Estatal de Investigación | Ref. PRE2021-098540, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Voltammetric methodology for the quality control and monitoring of sulfamethoxazole removal from water

  • Caruncho Pérez, Sara
  • Bernárdez Rodas, Nuria
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
  • González Romero, Elisa
Sulfamethoxazole is an antibiotic that is among the drugs most frequently found in waters around the world because of its habitual consumption and its high chemical stability that prevents it from being eliminated from the environment. In this study, an electroanalytical methodology based on differential pulse voltammetry is developed for the analysis of sulfamethoxazole at trace levels in water. After the optimization of the instrumental parameters a linear range from 6.59 to 96.27 μM was found with limits of detection and quantification of 1.98 and 6.59 μM, respectively, with an RSD below 6 %. Moreover, several validation studies involving different pH values, water samples and instrumentation-techniques were performed in order to ensure the robustness of the method. For this purpose, the peak area was used as quantitative variable since it is not affected by the pH of the medium even if there is any modification of this parameter during the experiments. Furthermore, the effect of other drug such as trimethoprim on the analytical signal of sulfamethoxazole was also evaluated. Once the method was developed it was tested on the quality control of Soltrim®, obtaining recoveries between 98 and 102 %. Lastly, the voltammetric method was applied for the in situ monitoring of sulfamethoxazole’s removal from water samples, specifically by anodic oxidation and electro-Fenton treatments. While the former was coupled to an adsorption process, the latter was carried out with different iron sources including commercial medicines that can be found in wastewater. The problem of significant variation in pH during the treatment was solved by working with the peak area, and so obtaining valid and reliable kinetic data. Although anodic oxidation proved to be faster considering the calculated kobs, electro-Fenton turned out to be more efficient in eliminating the drug, achieving the disappearance of its analytical signal in only 30 min of treatment., Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Heterogeneous Electro-Fenton-like designs for the disposal of 2-phenylphenol from water

  • Fernández Sanromán, Antía
  • Martínez Treinta, Rocío
  • Pazos Currás, Marta María
  • Rosales Villanueva, Emilio
  • Sanromán Braga, María Ángeles
The hunt for efficient and environmentally friendly degradation processes has positioned the heterogeneous advanced oxidation processes as an alternative more interesting and economical rather than homogenous processes. Hence, the current study lies in investigating the efficiency of different heterogeneous catalysts using transition metals in order to prevent the generation of iron sludge and to extend the catalogue of possible catalysts to be used in advanced oxidation processes. In this study, nickel and zinc were tested and the ability for radical-generation degradation capacity of both ions as homogeneous was evaluated in the electro-Fenton-like degradation of 2-phenylphenol. In both cases, the degradation profiles followed a first-order kinetic model with the highest degradation rate for nickel (1 mM) with 2-phenylphenol removal level of 90.12% and a total organic reduction near 70% in 2 h. To synthesise the heterogeneous nickel catalyst, this transition metal was fixed on perlite by hydrothermal treatment and in a biochar or carbon nanofibers by adsorption. From the removal results using the three synthesized catalysts, it is concluded that the best catalysts were obtained by inclusion of nickel on biochar or nanofibers achieving in both with removal around 80% before 1 h. Thus, to synthetize a nickel electrocatalyst, nickel doped nanofibers were included on carbon felt. To do this, the amount of carbon black, nickel nanofibers and polytetrafluoroethylene to add on the carbon felt was optimized by Taguchi design. The obtained results revealed that under the optimised conditions, a near-complete removal was achieved after 2 h with high stability of the nickel electrocatalyst that open the applicability of this heterogeneous system to operate in flow systems., Ministerio de Ciencia e Innovación | Ref. PDC2021-121394-I00, Ministerio de Ciencia e Innovación | Ref. CTM 2017-87326-R, Xunta de Galicia | Ref. ED431C 2021-43
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Disinfection through advance oxidation processes: optimization and application on real wastewater matrices

  • Blanco Canella, Pablo
  • Lama Rodríguez, Gabriela
  • Sanromán Braga, María Ángeles
  • Pazos Currás, Marta María
Disinfection is an essential and significant process for water treatment to protect the environment and human beings from pathogenic infections. In this study, disinfection through the generation of hydroxyl (Fenton process (FP)) and sulfate (Fenton-like process (FLP)) radicals was validated and optimized. The optimization was carried out in synthetic water through an experimental design methodology using the bacteria Escherichia coli as a model microorganism. Different variables were evaluated in both processes: precursor concentration (peroxymonosulfate (PMS) and H2O2), catalyst concentration (Fe+2), and pH in the Fenton process. After that, the optimized conditions (FP: 132.36 mM H2O2, 0.56 mM Fe+2 and 3.26 pH; FLP: 3.82 mM PMS and 0.40 mM Fe+2) were applied to real matrices from wastewater treatment plants. The obtained results suggest that both processes are promising for disinfection due to the high oxidant power of hydroxyl and sulfate radicals., Ministerio de Ciencia e Innovación | Ref. PDC2021-121394-I00, Ministerio de Ciencia e Innovación | Ref. PID2020-113667GB-I00
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Sustainable removal of antipyrine from wastewater via an eco-friendly heterogeneous electro-Fenton-like process employing Zero-Valent iron nanoparticles loaded activated carbon

  • Tesnim, Dhiss
  • Díez Sarabia, Aida Maria
  • Amor Hédi, Ben
  • Sanromán Braga, María Ángeles
  • Pazos Currás, Marta María
This study addresses the growing environmental and health concern associated with pharmaceutical compounds detected in wastewater by employing an innovative and environmentally friendly approach. Polyphenol reducing agents were extracted from palm petiole (PP) using a coffee marker to synthesize zero-valent iron nanoparticles (P-NZVI) in an environmentally sustainable manner. The residual PP materials after extraction were used to prepare an eco-friendly activated carbon (AC). Subsequently, the syntetized P-NZVIwere integrated with AC to form a composite AC-NZVI. After the physical–chemical characterization of the developed materials, AC and AC-NZVI were evaluated as catalysts in a heterogeneous electro-Fenton-like (EFL) process, employing a boron-doped diamond (BDD) as anode and carbon-felt (CF) as cathode to enhance antipyrine (ATP) degradation. This study investigates influential factors such as catalyst dosage, pH, current density, scavengers’ presence and water matrices effect. Results showcase a remarkable 97 % ATP removal efficiency and low energy consumption (EC) of 0.0683 kWh/g over 60 min EFL in deionized water with 1.4 g/L AC-NZVI and at current density of 10 mA/cm2. Quenching experiments emphasize hydroxyl radicals as the predominant species, particularly in acidic conditions. Notably, AC-NZVI exhibits high removal efficiencies even in real wastewater, achieving 87 % ATP removal. The study confirms the recyclability and stability of the AC-NZVI catalyst over five cycles, confirmed by comprehensive analyses, including FTIR, XPS, Raman, and XRD, achieving a mineralization efficiency of 84 % within 3 h. Elucidation of the ATP degradation pathway is accomplished through LC-MS., Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Xunta de Galicia | Ref. ED431C-2021–43, Xunta de Galicia | Ref. ED481D-2023/015
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Tesis doctoral (DoctoralThesis)

Application of biomaterials in aquatic contaminated environments, Biomateriales para su aplicación en la remediación de ambientes acuáticos contaminados, Biomateriais para a súa aplicación na remediación de ambientes acuáticos contaminados

  • Escudero Curiel, Silvia
The recovery of waste produced in various activities and allowing its return to the productive system within the goal of zero waste and as one of the maxims of the circular economy allows an improvement of both economic and environmental sustainability. These waste, both organic and inorganic, can be used for their application in environmental remediation processes. The presence of emerging pollutants in aquatic environments represents a significant problem given the pernicious effects they generate in living beings and their elimination focuses on new research for their elimination with various technologies such as adsorption and where it is required to obtain new more effective adsorbents . In this thesis project, we intend to develop new biomaterials for the treatment of aquatic environments contaminated with emerging pollutants of diverse nature. For this, it is proposed, on the one hand, to evaluate a mixture of different adsorbent biomaterials (such as agro-industrial waste) as well as the production of different carbonaceous materials obtained by various pretreatments followed by thermal treatments, which will be optimized, of these residues. The new adsorbents will be characterized and the elimination of representative compounds of contamination in polluted effluents will be investigated both individually and combined, relying on tools such as the design of experiments. The benignity of the proposed remediation strategies will be determined through toxicity analysis. The operating conditions will be optimized and the laboratory scale system will be studied both in discontinuous and continuous treatments, which will allow the simulation of the process through computer tools and facilitate its scaling., La valorización de residuos producidos en diversas actividades y que permita su retorno al sistema productivo dentro del objetivo de residuos cero y como una de las máximas de la economía circular permite una mejora de la sostenibilidad tanto económica como medioambiental. Dichos residuos, tanto orgánicos como inorgánicos, pueden ser empleados para su aplicación en procesos de remediación ambiental. La presencia de contaminantes emergentes en ambientes acuáticos representa una significativa problemática dados los efectos perniciosos que estos generan en los seres vivos y su eliminación focaliza nuevas investigaciones para su eliminación con diversas tecnologías como es la adsorción y donde se requiere la obtención de nuevos adsorbentes más eficaces. En el presente proyecto de Tesis se pretenden desarrollar nuevos biomateriales para el tratamiento de ambientes acuáticos contaminados con contaminantes emergentes de naturaleza diversa. Para ello, se propone, por una parte, evaluar una mezcla de diferentes biomateriales adsorbentes (tales como residuos agroindustriales) así como la producción de diferentes materiales carbonosos obtenidos mediante diversos pretratamientos seguidos de tratamientos térmicos, que se optimizarán, de estos residuos. Los nuevos adsorbentes se caracterizarán y se investigará la eliminación de compuestos representativos de contaminación en efluentes contaminados tanto a nivel individual como combinados apoyándose en herramientas como el diseño de experimentos. Se determinará la benignidad de las estrategias de remediación propuestas mediante análisis de toxicidad. Se optimizarán las condiciones de operación y se estudiará el sistema a escala laboratorio tanto en tratamientos en discontinuo como en continuo, lo que permitirá la simulación del proceso mediante herramientas informáticas y facilitará su escalado., A recuperación de residuos producidos en diversas actividades e permitir o seu regreso ao sistema produtivo dentro da meta de cero residuos como unha economía circular superior permite unha mellora tanto na sustentabilidade económica e ambiental. Estes residuos, tanto orgánicos como inorgánicos, pódense utilizar para a súa aplicación nos procesos de remediación ambiental. A presenza de contaminantes emerxentes en ambientes acuáticos representa un problema significativo, dado os efectos destrutivos que xeran nos organismos vivos ea súa eliminación céntrase máis investigacións para eliminación con varias tecnoloxías, como a adsorção e onde a obtención de novos adsorbentes máis eficaz require . No presente proxecto de tese pretende desenvolver novos biomateriais para o tratamento de contaminados con contaminantes de varias naturezas ambientes acuáticos emerxente. Para estes efectos, propón-se, por unha banda, para avaliar unha mestura de diferentes biomateriais adsorbentes (tales como residuos agro-industriais) ea produción de diferentes materiais carbonáceos obtidos por varios pre-tratamentos seguido tratamentos de calor a ser optimizado, destes residuos. Novos adsorbentes caracterizado e retirada de compostos representativos de contaminación contaminado tanto individualmente e efluentes combinados foron investigadas como ferramentas baseándose na concepción de experiencias. A benignidade das estratexias de remediación propostas determinaranse mediante a análise de toxicidade. as condicións de funcionamento foron optimizados eo sistema será estudada en ambos escala tratamento de lote e de laboratorio continuo, permitindo que a simulación do proceso utilizando ferramentas e facilitar o seu dimensionamento., Agencia Estatal de Investigación | Ref. CTM 2017-87326-R, Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Xunta de Galicia | Ref. ED431C 2017/47, Xunta de Galicia | Ref. ED431C 2021-43
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Pushing the operational barriers for g-C3N4: a comprehensive review of cutting-edge immobilization strategies

  • Fernández Sanromán, Antía
  • Pazos Currás, Marta María
  • Rosales Villanueva, Emilio
  • Sanromán Braga, María Ángeles
This comprehensive review explores recent advancements in immobilization strategies for graphitic carbon nitride (g-C3N4), a metal-free photocatalyst that has gained significant attention for its optical and physicochemical properties comparable to traditional photocatalysts like TiO2. However, a critical challenge regarding their application has emerged from the difficulty of its recovery due to its powdery nature. Therefore, several alternatives are being explored to immobilize this material, facilitating its recovery and reuse. This review systematically categorizes various physical and chemical immobilization techniques, providing an in-depth analysis of their advantages, drawbacks, and applications. Techniques such as encapsulation, electrospinning, casting, and coating, along with their adaptations for g-C3N4, are thoroughly examined. Additionally, the impact of these strategies on enhancing the photocatalytic efficiency and operational stability of g-C3N4, particularly in environmental applications, is also assessed. Thus, this review aims to provide valuable insights and guide future research in the realms of photocatalysis and environmental remediation. The review contributes to the understanding of how immobilization strategies can optimize the performance of g-C3N4, furthering its potential applications in sustainable and efficient environmental solutions., Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Agencia Estatal de Investigación | Ref. PCI2022-132941, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Xunta de Galicia | Ref. ED431C 2021-43
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Advancing in wastewater treatment using sustainable electrosorbents

  • Fernández Sanromán, Antía
  • Pazos Currás, Marta María
  • Rosales Villanueva, Emilio
  • Sanromán Braga, María Ángeles
Separation and purification processes using adsorption are becoming more and more popular, with excellent benefit-cost ratio and high effluent quality. However, it is important to recognize the requirement for new adsorbents and to avoid the generation of contaminated adsorbents that can have a severe impact on the environment. Thus, underscoring the need for sustainable approaches in the management and regeneration of these materials. To improve this process, two challenges are being approached nowadays: the synthesis of adsorbents from wastes in a circular economy model and its integration with electrochemistry (electrosorption) to enhance the adsorbent capacity and its regeneration by green electricity. This review summarizes the key studies and trends related to electrosorption (60 articles) and its application in the removal of different pollutants from wastewater. It must be highlighted that around 33% of them, detailed the synthesis of green electrosorbents with application in the removal of inorganic and organic pollutants. In addition, other studies with non-sustainable electrodes (approximately 23%) describe the last trend to improve electrosorbent characteristics. From our standpoint, it is crucial to delve into this research, particularly regarding their application to green electrosorbents to enhance the efficiency of electrosorption processes, a potential breakthrough in the field., Agencia Estatal de Investigación | Ref. PCI2022-132941, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Xunta de Galicia | Ref. ED431C 2021-43, Agencia Estatal de Investigación | Ref. PRE2021-098540, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

From waste to resource: valorization of lignocellulosic agri-food residues through engineered hydrochar and biochar for environmental and clean energy applications—a comprehensive review

  • Escudero Curiel, Silvia
  • Giráldez Rodríguez, Alba
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
Agri-food residues or by-products have increased their contribution to the global tally of unsustainably generated waste. These residues, characterized by their inherent physicochemical properties and rich in lignocellulosic composition, are progressively being recognized as valuable products that align with the principles of zero waste and circular economy advocated for by different government entities. Consequently, they are utilized as raw materials in other industrial sectors, such as the notable case of environmental remediation. This review highlights the substantial potential of thermochemical valorized agri-food residues, transformed into biochar and hydrochar, as versatile adsorbents in wastewater treatment and as promising alternatives in various environmental and energy-related applications. These materials, with their enhanced properties achieved through tailored engineering techniques, offer competent solutions with cost-effective and satisfactory results in applications in various environmental contexts such as removing pollutants from wastewater or green energy generation. This sustainable approach not only addresses environmental concerns but also paves the way for a more eco-friendly and resource-efficient future, making it an exciting prospect for diverse applications., Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Agencia Estatal de Investigación | Ref. PCI2022-132941, Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Xunta de Galicia | Ref. ED431C 2021-43, Universidade de Vigo
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Sustainable regeneration of a honeycomb carbon aerogel used as a high-capacity adsorbent for Fluoxetine removal

  • Escudero Curiel, Silvia
  • Pazos Currás, Marta María
  • Sanromán Braga, María Ángeles
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, Pharmaceuticals and personal care products (PPCPs) harm ecosystems and human health. The focus is now being put on regulating discharges at wastewater treatment plants (WWTPs). Stressful and lonely lifestyles, accentuated by the COVID-19 outbreak, have led to an increase in the consumption of antidepressants, particularly in the form of Fluoxetine (FLX). A highly effective process for the removal of PPCPs is of key importance for the economic feasibility of the process in the industry. Consequently, a high-capacity adsorption/regeneration system is crucial to solving this problem. In this study, the removal of FLX by an adsorption process and the subsequent in situ regeneration of the adsorbent was evaluated in successive cycles. NQ40 honeycomb 3D carbon aerogel was employed as a high-capacity adsorbent, obtaining uptakes of 125.24 mg/g. A detailed study of NQ40 and the mechanisms governing the adsorption process was conducted, with chemisorption and intra-particle diffusion playing the main role. A Fenton and a Fenton-like process with peroxymonosulfate (PMS) were evaluated for regeneration purposes, finding hydrogen peroxide to be more efficient in removing a high concentration of FLX. A regeneration capacity of 98.85% was achieved in the first NQ40 adsorption-regeneration cycle and 98.04% in the second one, without negatively affecting the structural characteristics of NQ40. Therefore, with a high porosity, low density, high biocompatibility, high chemical stability and 3D structural stability, this aerogel is at the forefront of novel high-capacity adsorbent materials for industrial-scale use in WWTPs., Agencia Estatal de Investigación | Ref. PID2020-113667GB-I00, Agencia Estatal de Investigación | Ref. PDC2021-121394-I00, Xunta de Galicia | Ref. ED431C 2021-43